74AVC16374 NEXPERIA | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 16
Technical content
are provided per 8-bit section. minimum amount of power consumption. be tied to VCC through a pull-up resistor (Live Insertion). drive during transient (see Figure 5 and Figure 6). Table 1. Ordering information
© Nexperia B.V. 2017. All rights reserved 74AVC16374 All information provided in this document is subject to legal disclaimers. Product data sheet Rev. 3 — 16 August 2013 2 of 16 Nexperia 74AVC16374 16-bit edge triggered D-type flip-flop; 3.6 V tolerant; 3-state 4. Functional diagram Fig 1. IEC logic symbol Fig 2. Logic symbol mna577 37 12 1D7 1D0 1D1 1D2 1D3 1D4 1D5 1D6 1Q7 1Q6 1Q5 1Q4 1Q3 1Q2 1Q0 1Q1 2D5 2D0 2D1 2D2 2D3 2D4 2Q5 2Q4 2Q3 2Q2 2Q1 2Q0 2EN 1OE 1 1EN 1CP 2OE 2CP 48 C1 1D 1 2D 2 2D7 2D6 2Q7 2Q6 mna576 1Q0 1Q1 1CP 2CP 1Q2 1Q3 1Q4 1Q5 1Q6 1Q7 1OE 48 25 2Q0 2Q1 2Q2 2Q3 2Q4 2Q5 2Q6 2Q7 1D0 1D1 1D2 1D3 1D4 1D5 1D6 1D7 2D0 2D1 2D2 2D3 2D4 2D5 2D6 2D7 2OE Fig 3. Logic diagram mna578 1CP D CP Q 1OE to 7 other channels FF1 1Q01D0 2CP D CP Q 2OE to 7 other channels FF9 2Q02D0
© Nexperia B.V. 2017. All rights reserved 74AVC16374 All information provided in this document is subject to legal disclaimers. Product data sheet Rev. 3 — 16 August 2013 3 of 16 Nexperia 74AVC16374 16-bit edge triggered D-type flip-flop; 3.6 V tolerant; 3-state 5. Pinning information
5.1 Pinning
Fig 4. Pin configuration 74AVC16374 1OE 1CP 1Q0 1D0 1Q1 1D1 GND GND 1Q2 1D2 1Q3 1D3 VCC VCC 1Q4 1D4 1Q5 1D5 GND GND 1Q6 1D6 1Q7 1D7 2Q0 2D0 2Q1 2D1 GND GND 2Q2 2D2 2Q3 2D3 VCC VCC 2Q4 2D4 2Q5 2D5 GND GND 2Q6 2D6 2Q7 2D7 2OE 2CP mna575
74AVC16374 All information provided in this document is subject to legal disclaimers.
5.2 Pin description
Table 2. Pin description Table 3. Function table [1]
74AVC16374 All information provided in this document is subject to legal disclaimers. [1] The input and output voltage ratings may be exceeded if the input and output current ratings are observed. [2] Above 60 C, the value of Ptot derates linearly with 5.5 mW/K.
- Recommended operating conditions
Table 4. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V). Table 5. Recommended operating conditions
74AVC16374 All information provided in this document is subject to legal disclaimers. [1] All typical values are measured at T amb =2 5 C. Table 6. Static characteristics At recommended operating conditions. Voltages are referenced to GND (ground = 0 V).
74AVC16374 All information provided in this document is subject to legal disclaimers.
9.1 Graphs
Table 7. Dynamic characteristics Voltages are referenced to GND (ground = 0 V). tr = tf 2 ns. For test circuit, see Figure 10.
74AVC16374 All information provided in this document is subject to legal disclaimers. [1] t pd is the same as tPLH and tPHL. ten is the same as tPZL and tPZH. tdis is the same as tPLZ and tPHZ. [3] C PD is used to determine the dynamic power dissipation (PD in W). (CL VCC2 fo) = sum of the outputs. Table 7. Dynamic characteristics …continued Voltages are referenced to GND (ground = 0 V). tr = tf 2 ns. For test circuit, see Figure 10.
© Nexperia B.V. 2017. All rights reserved 74AVC16374 All information provided in this document is subject to legal disclaimers. Product data sheet Rev. 3 — 16 August 2013 9 of 16 Nexperia 74AVC16374 16-bit edge triggered D-type flip-flop; 3.6 V tolerant; 3-state 11. Waveforms Measurement points are given in Table 9. Logic levels: VOL and VOH are typical output voltage levels that occur with the output load. Fig 7. Clock input (nCP) to out put (nQn) propagation delays mna579 nCP input nQn output tPHL tPLH tW VM VOH VI GND VOL VM VM 1/fmax Measurement points are given in Table 9. Logic levels: VOL and VOH are typical output voltage levels that occur with the output load. Fig 8. 3-state enable and disable times mna478 tPLZ tPHZ outputs disabled outputs enabled VY VX outputs enabled output LOW-to-OFF OFF-to-LOW output HIGH-to-OFF OFF-to-HIGH nOE input VI VOL VOH VCC VM GND GND tPZL tPZH VM VM
74AVC16374 All information provided in this document is subject to legal disclaimers. Measurement points are given in Table 9. Logic levels: VOL and VOH are typical output voltage levels that occur with the output load. Table 8. Measurement points
74AVC16374 All information provided in this document is subject to legal disclaimers. Test data is given in Table 9. CL = Load capacitance including jig and probe capacitance. RT = Termination resistance should be equal to output impedance Zo of the pulse generator. VEXT = External voltage for measuring switching times. Table 9. Test data
1.2 V VCC 2 ns 15 pF 2 k open 2 VCC GND
© Nexperia B.V. 2017. All rights reserved 74AVC16374 All information provided in this document is subject to legal disclaimers. Product data sheet Rev. 3 — 16 August 2013 12 of 16 Nexperia 74AVC16374 16-bit edge triggered D-type flip-flop; 3.6 V tolerant; 3-state 12. Package outline Fig 11. Package outline SOT362-1 (TSSOP48) ReferencesOutline version European projection Issue date IEC JEDEC JEITA SOT362-1 MO-153 sot362-1_po 03-02-19 13-08-05 Unit mm max nom min 0.15 0.28 0.2 12.6 0.5 0.8 A Dimensions (mm are the original dimensions) Note 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic interlead protrusions of 0.25 mm maximum per side are not included. TSSOP48: plastic thin shrink small outline package; 48 leads; body width 6.1 mm SOT362-1 A1 A2 1.05 A3 bp cD (1) θE(2) eH E L Lp Qvw yZ 8.3 0.86.2 0.50 pin 1 index vA θ A D Lp Q E Z c L 12 4 48 25 e w y X A HE bp detail X (A3) 0 5 mm scale 2.5
74AVC16374 All information provided in this document is subject to legal disclaimers. Table 10. Abbreviations Table 11. Revision history
- The format of this data sheet has been redesigned to comply with the new identity guidelines of NXP Semiconductors .
- Legal texts have been adapted to the new company name where appropriate. 74AVC16374 v.2 20000309 Product specification - - 74AVC16374 v.1 74AVC16374 v.1 19981211 Pr oduct specification - - -
© Nexperia B.V. 2017. All rights reserved 74AVC16374 All information provided in this document is subject to legal disclaimers. Product data sheet Rev. 3 — 16 August 2013 14 of 16 Nexperia 74AVC16374 16-bit edge triggered D-type flip-flop; 3.6 V tolerant; 3-state 15. Legal information
15.1 Data sheet status
[1] Please consult the most recently issued document before initiating or completing a design. [2] The term ‘short data sheet’ is explained in section “Definitions”. [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nexperia.com .
15.2 Definitions
Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. Nexperia does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request vi a the local Nexperia sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. Product specification — The information and data provided in a Product data sheet shall define the specification of the product as agreed between Nexperia and its customer , unless Nexperia and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the Nexperia product is deemed to offer functions and qualities beyond those described in the Product data sheet.
15.3 Disclaimers
Limited warranty and liability — Information in this document is believed to be accurate and reliable. However, Nexperia does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. Nexperia takes no responsibility for the content in this document if provided by an information source outside of Nexperia. In no event shall Nexperia be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, Nexperia’s aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of Nexperia. Right to make changes — Nexperia reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use — Nexperia products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of a Nexperia product can reasonably be expected to result in personal injury, death or severe property or environmental damage. Nexperia and its suppliers accept no liability for inclusion and/or use of Nexperia products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications — Applications that are described herein for any of these products are for illustrative purpos es only. Nexperia makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using Nexperia products, and Nexperia accepts no liability for any assistance with applications or customer product design. It is customer’s sole responsibility to determine whether the Nexperia product is suitable and fit for the customer’s applications and products planned, as well as for the planned application and use of customer’s third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. Nexperia does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer’s applications or products, or the application or use by customer’s third party customer(s). Customer is responsible for doing all necessary testing for the customer’s applications and products using Nexperia products in order to av oid a default of the applications and the products or of the application or use by customer’s third party customer(s). Nexperia does not accept any liability in this respect. Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. Terms and conditions of commercial sale — Nexperia products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nexperia.com/profile/terms , unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. Nexperia hereby expressly objects to applying the customer’s general terms and conditions with regard to the purchase of Nexperia products by customer. No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification.
© Nexperia B.V. 2017. All rights reserved 74AVC16374 All information provided in this document is subject to legal disclaimers. Product data sheet Rev. 3 — 16 August 2013 15 of 16 Nexperia 74AVC16374 16-bit edge triggered D-type flip-flop; 3.6 V tolerant; 3-state Export control — This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from competent authorities. Non-automotive qualified products — Unless this data sheet expressly states that this specific Nexperia product is automotive qualified, the product is not suitable for automotive use. It is neither qualified nor tested in accordance with automotive testing or application requirements. Nexperia accepts no liabili ty for inclusion and/or use of non-automotive qualified products in automotive equipment or applications. In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without Nexperia’s warranty of the product for such automotive applications, use and specifications, and (b) whenever customer uses the product for automotive applications beyond Nexperia’s specifications such use shall be solely at customer’s own risk, and (c) customer fully indemnifies Nexperia for any liability, damages or failed product claims resulting from customer design and use of the product for automotive app lications beyond Nexperia’s standard warranty and Nexperia’s product specifications . Translations — A non-English (translated) version of a document is for reference only. The English version shall prevail in case of any discrepancy between the translated and English versions.
15.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. 16. Contact information For more information, please visit: http://www.nexperia.com For sales office addresses, please send an email to: salesaddresses@nexperia.com
16-bit edge triggered D-type flip-flop; 3.6 V tolerant; 3-state 17. Contents © Nexperia B.V. 2017. All rights reserved For more information, please visit: http://www.nexperia.com For sales office addresses, please send an email to: salesaddresses@nexperia.com Date of release: