74AHCT132 NEXPERIA | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 16
Technical content
Datasheet sections
74AHC132; 74AHCT132 Quad 2-input NAND Schmitt trigger Rev. 7 — 3 July 2020 Product data sheet 1. General description The 74AHC132; 74AHCT132 is a quad 2-input NAND gate with Schmitt-trigger inputs. Inputs are overvoltage tolerant. This feature allows the use of these devices as translators in mixed voltage environments. 2. Features and benefits
- Wide supply voltage range from 2.0 V to 5.5 V
- Overvoltage tolerant inputs to 5.5 V
- High noise immunity
- CMOS low power dissipation
- Input levels:
- For 74AHC132: CMOS level
- For 74AHCT132: TTL level
- ESD protection:
- HBM JESD22-A114E exceeds 2000 V
- MM JESD22-A115-A exceeds 200 V
- CDM JESD22-C101C exceeds 1000 V
- Latch-up performance exceeds 100 mA per JESD 78 Class II Level A
- Multiple package options
- Specified from -40 °C to +85 °C and from -40 °C to +125 °C
Table 1. Ordering information
Table 2. Pin description Table 3. Function table H = HIGH voltage level; L = LOW voltage level.
Table 4. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V). [1] The input and output voltage ratings may be exceeded if the input and output current ratings are observed. [2] For SOT108-1 (SO14) package: Ptot derates linearly with 10.1 mW/K above 100 °C. For SOT402-1 (TSSOP14) package: Ptot derates linearly with 7.3 mW/K above 81 °C. For SOT762-1 (DHVQFN14) package: Ptot derates linearly with 9.6 mW/K above 98 °C.
- Recommended operating conditions
Table 5. Recommended operating conditions Voltages are referenced to GND (ground = 0 V).
Table 6. Static characteristics At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
Table 7. Dynamic characteristics Voltages are referenced to GND (ground = 0 V); for test circuit see Fig. 7. [1] Typical values are measured at nominal supply voltage (VCC = 3.3 V and VCC = 5.0 V). [2] tpd is the same as tPLH and tPHL. [3] CPD is used to determine the dynamic power dissipation (PD in μW). Σ(CL x VCC 2 x fo) = sum of the outputs.
Measurement points are given in Table 8. VOL and VOH are typical voltage output levels that occur with the output load. Table 8. Measurement points Test data is given in Table 9. RT = termination resistance should be equal to output impedance Zo of the pulse generator. CL = load capacitance including jig and probe capacitance. Table 9. Test data
- Transfer characteristics
Table 10. Transfer characteristics At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
Nexperia 74AHC132; 74AHCT132 Quad 2-input NAND Schmitt trigger 0 1 3 1.5 0.5 mna411
2 VI (V)
(mA) 0 5VI (V) ICC (mA) mna412 1 2 3 4 a. VCC = 3.0 V b. VCC = 4.5 V 0 2 6 mna413
4 VI (V)
(mA) c. VCC = 5.5 V Fig. 10. Typical 74AHC132 transfer characteristics 0 5VI (V) ICC (mA) mna414 1 2 3 4 0 2 6 mna415 (mA) a. VCC = 4.5 V b. VCC = 5.5 V Fig. 11. Typical 74AHCT132 transfer characteristics 74AHC_AHCT132 All information provided in this document is subject to legal disclaimers. © Nexperia B.V. 2020. All rights reserved Product data sheet Rev. 7 — 3 July 2020 9 / 16
Nexperia 74AHC132; 74AHCT132 Quad 2-input NAND Schmitt trigger 12. Application information 001aac440 VCC VCC A B Y R C For 74AHC132: For 74AHCT132: Fig. 12. Relaxation oscillator 74AHC_AHCT132 All information provided in this document is subject to legal disclaimers. © Nexperia B.V. 2020. All rights reserved Product data sheet Rev. 7 — 3 July 2020 10 / 16
Nexperia 74AHC132; 74AHCT132 Quad 2-input NAND Schmitt trigger 13. Package outline UNIT A max. A 1 A 2 A 3 b p c D (1) E (1) (1) e H E L L p Q Z y w v θ REFERENCES OUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm inches 1.75 0.25 0.10 1.45 1.25 0.25 0.49 0.36 0.25 0.19 8.75 8.55 4.0 3.8 1.27 6.2 5.8 0.7 0.6 0.7 0.3 8 o o 0.25 0.1 DIMENSIONS (inch dimensions are derived from the original mm dimensions) Note 1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included. 1.0 0.4 SOT108-1 X w M θ A A 1 A 2 b p D H E L p Q detail X E Z e c L v M A (A ) 3 A y 076E06 MS-012 pin 1 index 0.069 0.010 0.004 0.057 0.049 0.01 0.019 0.014 0.0100 0.0075 0.35 0.34 0.16 0.15 0.05 1.05 0.041 0.244 0.228 0.028 0.024 0.028 0.012 0.01 0.25 0.01 0.004 0.039 0.016 99-12-27 03-02-19 0 2.5 5 mm scale SO14: plastic small outline package; 14 leads; body width 3.9 mm SOT108-1 Fig. 13. Package outline SOT108-1 (SO14) 74AHC_AHCT132 All information provided in this document is subject to legal disclaimers. © Nexperia B.V. 2020. All rights reserved Product data sheet Rev. 7 — 3 July 2020 11 / 16
Nexperia 74AHC132; 74AHCT132 Quad 2-input NAND Schmitt trigger UNIT A 1 A 2 A 3 b p c D (1) E (2) (1) e H E L L p Q Z y w v θ REFERENCES OUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm 0.15 0.05 0.95 0.80 0.30 0.19 0.2 0.1 5.1 4.9 4.5 4.3 0.65 6.6 6.2 0.4 0.3 0.72 0.38 o o 0.13 0.1 0.2 1 DIMENSIONS (mm are the original dimensions) Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic interlead protrusions of 0.25 mm maximum per side are not included. 0.75 0.50 SOT402-1 MO-153 99-12-27 03-02-18 w M b p D Z e 0.25 1 7 14 8 θ A A 1 A 2 L p Q detail X L (A ) 3 H E E c v M A X A y 0 2.5 5 mm scale TSSOP14: plastic thin shrink small outline package; 14 leads; body width 4.4 mm SOT402-1 A max. 1.1 pin 1 index Fig. 14. Package outline SOT402-1 (TSSOP14) 74AHC_AHCT132 All information provided in this document is subject to legal disclaimers. © Nexperia B.V. 2020. All rights reserved Product data sheet Rev. 7 — 3 July 2020 12 / 16
Nexperia 74AHC132; 74AHCT132 Quad 2-input NAND Schmitt trigger ReferencesOutline version European projection Issue date IEC JEDEC JEITA SOT762-1 MO-241 sot762-1_po 15-04-10 15-05-05 Unit mm max nom min 1 0.05 3.1 1.65 2.6 0.5 2 0.4 A(1) Dimensions (mm are the original dimensions) Note 1. Plastic or metal protrusions of 0.075 mm maximum per side are not included. DHVQFN14: plastic dual in-line compatible thermal enhanced very thin quad flat package; no leads; 14 terminals; body 2.5 x 3 x 0.85 mm SOT762-1 A1 b 0.30 c D(1) Dh E(1) Eh 1.00 e e1 k k L v 0.1 w y 0.51.15 0 4 mm2 scale terminal 1 index area A c L Eh Dh k b 2 6 13 9 D E terminal 1 index area e e C yCy1 AC Bv Cw detail X AB X Fig. 15. Package outline SOT762-1 (DHVQFN14) 74AHC_AHCT132 All information provided in this document is subject to legal disclaimers. © Nexperia B.V. 2020. All rights reserved Product data sheet Rev. 7 — 3 July 2020 13 / 16
Table 11. Abbreviations Table 12. Revision history
- Legal texts have been adapted to the new company name where appropriate.
- Section 1 and Section 2 updated.
- Table 4: Derating values for Ptot total power dissipation updated.
- Package outline drawing of SOT762-1 (Fig. 15) updated. 74AHC_AHCT132 v.6 20090504 Product data sheet - 74AHC_AHCT132 v.5 Modifications: • Table 6: the conditions for HIGH-level output voltage and LOW-level output voltage have been changed. 74AHC_AHCT132 v.5 20080509 Product data sheet - 74AHC_AHCT132 v.4 74AHC_AHCT132 v.4 20050207 Product data sheet - 74AHC_AHCT132 v.3 74AHC_AHCT132 v.3 20040415 Product specification - 74AHC_AHCT132 v.2 74AHC_AHCT132 v.2 19990924 Product specification - 74AHC_AHCT132 v.1 74AHC_AHCT132 v.1 19990531 Product specification - - 74AHC_AHCT132 All information provided in this document is subject to legal disclaimers. © Nexperia B.V. 2020. All rights reserved Product data sheet Rev. 7 — 3 July 2020 14 / 16
Nexperia 74AHC132; 74AHCT132 Quad 2-input NAND Schmitt trigger 16. Legal information Data sheet status Document status [1][2] Product status [3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification. [1] Please consult the most recently issued document before initiating or completing a design. [2] The term 'short data sheet' is explained in section "Definitions". [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the internet at https://www.nexperia.com. Definitions Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. Nexperia does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local Nexperia sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. Product specification — The information and data provided in a Product data sheet shall define the specification of the product as agreed between Nexperia and its customer, unless Nexperia and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the Nexperia product is deemed to offer functions and qualities beyond those described in the Product data sheet. Disclaimers Limited warranty and liability — Information in this document is believed to be accurate and reliable. However, Nexperia does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. Nexperia takes no responsibility for the content in this document if provided by an information source outside of Nexperia. In no event shall Nexperia be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, Nexperia’s aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of Nexperia. Right to make changes — Nexperia reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use — Nexperia products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an Nexperia product can reasonably be expected to result in personal injury, death or severe property or environmental damage. Nexperia and its suppliers accept no liability for inclusion and/or use of Nexperia products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Quick reference data — The Quick reference data is an extract of the product data given in the Limiting values and Characteristics sections of this document, and as such is not complete, exhaustive or legally binding. Applications — Applications that are described herein for any of these products are for illustrative purposes only. Nexperia makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using Nexperia products, and Nexperia accepts no liability for any assistance with applications or customer product design. It is customer’s sole responsibility to determine whether the Nexperia product is suitable and fit for the customer’s applications and products planned, as well as for the planned application and use of customer’s third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. Nexperia does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer’s applications or products, or the application or use by customer’s third party customer(s). Customer is responsible for doing all necessary testing for the customer’s applications and products using Nexperia products in order to avoid a default of the applications and the products or of the application or use by customer’s third party customer(s). Nexperia does not accept any liability in this respect. Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. Terms and conditions of commercial sale — Nexperia products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nexperia.com/profile/terms, unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. Nexperia hereby expressly objects to applying the customer’s general terms and conditions with regard to the purchase of Nexperia products by customer. No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. Export control — This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from competent authorities. Non-automotive qualified products — Unless this data sheet expressly states that this specific Nexperia product is automotive qualified, the product is not suitable for automotive use. It is neither qualified nor tested in accordance with automotive testing or application requirements. Nexperia accepts no liability for inclusion and/or use of non-automotive qualified products in automotive equipment or applications. In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without Nexperia’s warranty of the product for such automotive applications, use and specifications, and (b) whenever customer uses the product for automotive applications beyond Nexperia’s specifications such use shall be solely at customer’s own risk, and (c) customer fully indemnifies Nexperia for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond Nexperia’s standard warranty and Nexperia’s product specifications. Translations — A non-English (translated) version of a document is for reference only. The English version shall prevail in case of any discrepancy between the translated and English versions. Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. 74AHC_AHCT132 All information provided in this document is subject to legal disclaimers. © Nexperia B.V. 2020. All rights reserved Product data sheet Rev. 7 — 3 July 2020 15 / 16