72SXE100M

SXE PANASONIC | Alldatasheet

Document overview

• Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
• PDF pages: 8

Technical content

Features

Marking Dimensions (not to scale) Specifications 18 μF to 120 μF SXE series E12 F8 F13 Capacitance tolerance DC leakage current 15 μF to 39 μF Capacitance change 15 min. 4 min. 19 min.L max. øD F ød Polarity marking (−) R. capacitance (μF) Series code* R. voltage (V) Lot No. Some part numbers are not a recommended product. Not recommended for new design.

*1: Ripple current (100 kHz / +105 ℃ < Tx ≦ +125 ℃) / Allowable ripple current (100 kHz / Tx ≦ +105 ℃) *2: ESR (100 kHz to 300 kHz / +20 ℃) Not recommended for new design *4: After 2 minutes ◆ Please refer to each page in this catarog for “Flow conditions” and “Taping specifications”. Rated voltage (V) Rated capacitance (±20 %) (μF) Case size Size code Should a safety concern arise regarding this product, please be sure to contact us immediately. 21-Oct-24 Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. 100 10.0 13.0 F13 1030 3280 25 0.12 18 8.0 7.0 E7 63SXE18M 63SXE33M (mm) øD L 10.0 8.0 F8 8.0 12.0 E12 8.0 12.0 E12 0.12 1100 2950 2950 2190 340 930 930 0.12 0.12 0.12 Part number 10.0 13.0 F13 56 8.0 12.0 E12 12 8.0 7.0 E7 10.0 120 68 8.0 12.0 E12 10.0 13.0 F13 104 122 122 10.0 13.0 F13 28 3100 3100 780 780 660 780 8.0 12.0 E12 8.0 12.0 E12 10.0 13.0 F13 8.0 6.8 8.0 7.0 E7 10.0 13.0 F13 100 kHz ≦ f < 500 kHz Coefficient 0.05 0.3 0.7 1 Frequency(f) 120 Hz ≦ f < 1 kHz 1 kHz ≦ f < 10 kHz 10 kHz ≦ f < 100 kHz 10.0 8.0 F8 0.12 0.12 340 630 100SXE15MX 63SXE39M 63SXE39MX 63SXE56M 63SXE68MX 63SXE68M 63SXE120M 72SXE82M 72SXE100M 80SXE12M 80SXE27M 80SXE27MX 80SXE33M 80SXE47MX 80SXE47M 80SXE56M 80SXE82M 100SXE6R8M 980 980 0.12 176 214 214 378 295 360 1100 2000 2950 2950 3280 3280 3100 0.12 0.12 0.12 2490 3100 1100 0.12 0.12 328 108 108 132 188 188 224 0.12 2490 3100 2080 2490 Frequency correction factor for ripple current Characteristics list 690 930 930 1030 1030 980 Ripple current*1 (mA rms) Allowable ripple current*1 (mA rms) Specifications LC*4 (μA)tan δ*3ESR*2 (mΩ max.) 63SXE100M 2872 82 13.0 F13 100 10.0 13.0 F13 28980 0.12 315 60 0.12 48 27 35 0.12 10.0 8.0 F8 55 0.12 33 35 0.12 47 12.0 E12 980 340 0.12 0.12 100 15 8.0 12.0 E12 730 2350 40 0.12 22 10.0 13.0 F13 940 3000 30 0.12 39 10.0 13.0 F13 940 3000 30 75 100SXE15M 18 10.0 13.0 F13 940 3000 30 0.12 90 100SXE18M 8.0 12.0 E12 730 2350 40 0.12 90 100SXE18MX 0.12 195 100SXE39M 110 100SXE22M 27 8.0 12.0 E12 730 2350 40 0.12 135 100SXE27MX 10.0 13.0 F13 940 3000 30 0.12 135 100SXE27M Click here for part number list of lead terminal cutting and lead terminal taping NRFND NRFND NRFND NRFND

◇ Radial lead type

• Lead terminal process 1-1. Correspondence list ※ The following table is a standard specification. Please contact us separately concerming specifications except for that mentioned below. 1-2. Lead terminal cutting specifications Unit：mm 1-3. Taping specifications for automatic insertion Unit：mm
• Minimum packing quantity and weight SXE series Packing specifications Series Size code Bag-packed products (lead terminal cutting) Taping productsNot processed Straight cut Process names Size code Lead terminal cutting code Lead terminal dimensions Straight cut E7, E12 F8, F13 +C3 (+3) SXE E7, E12 No code +C3 (+3) +TSS（+S) F8, F13 No code +C3 (+3) +T Size code Case size F Taping code Taping dimensions E7, E12 ø8 F=3.5 mm +TSS (+S) ±1.0 ±1.0 ±0.5 P2 Δｈ W F8, F13 ø10 F=5.0 mm +T Code F P P０ P1 H øD０W０ W1 W2 4.60 6.35 Tolerance ±1.0 ±0.2 ±0.5 4.0 Code t ℓ L Tolerance ±0.3 max. max. +T ø10 0.6 0 11.0 E7 ø8 200 110 1000 820 Size code Case size Bag-packed products Taping products Quantity(pcs./Bag) Typical weight(g) Quantity(pcs./Bag) Typical weight(g) F8 ø10 200 180 500 890 E12 ø8 200 200 1000 980 Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 04-Oct-24 F13 ø10 200 280 500 940 L 3.5±0.5 +0.8 －0.2 Carrier tape Hold-down tape Carrier tape Hold-down tape

100SXE27MX 100SXE27MX+3 100SXE27MX+S 04-Oct-24 100SXE27M 100SXE27M+3 100SXE27M+T 100SXE39M 100SXE39M+3 100SXE39M+T SXE 63SXE18M 63SXE18M+3 63SXE18M+S 100SXE18MX 100SXE18MX+3 100SXE18MX+S 100SXE22M 100SXE22M+3 100SXE22M+T 100SXE15M 100SXE15M+C3 100SXE15M+TSS 100SXE18M 100SXE18M+3 100SXE18M+T 100SXE6R8M 100SXE6R8M+3 100SXE6R8M+S 100SXE15MX 100SXE15MX+3 100SXE15MX+T 80SXE56M 80SXE56M+3 80SXE56M+T 80SXE82M 80SXE82M+3 80SXE82M+T 80SXE47MX 80SXE47MX+3 80SXE47MX+S 80SXE47M 80SXE47M+3 80SXE47M+T 80SXE27MX 80SXE27MX+3 80SXE27MX+T 80SXE33M 80SXE33M+3 80SXE33M+S 80SXE12M 80SXE12M+3 80SXE12M+S 80SXE27M 80SXE27M+3 80SXE27M+S 72SXE82M 72SXE82M+3 72SXE82M+T 72SXE100M 72SXE100M+3 72SXE100M+T 63SXE100M 63SXE100M+3 63SXE100M+T 63SXE120M 63SXE120M+3 63SXE120M+T 63SXE68MX 63SXE68MX+3 63SXE68MX+S 63SXE68M 63SXE68M+3 63SXE68M+T 63SXE56M 63SXE56M+3 63SXE56M+S 63SXE39MX 63SXE39MX+3 63SXE39MX+T 63SXE33M 63SXE33M+C3 63SXE33M+TSS 63SXE39M Radial lead (Lead terminal cutting / Lead terminal taping) Series No processing Lead terminal cutting Lead terminal taping 63SXE39M+3 63SXE39M+S

Safety and Legal Matters to Be Observed ■ Please be advised that this product and product specifications are subject to change without notice for improvement purposes. Therefore, please request and confirm the latest delivery specifications that explain the specifications in detail before the final design, or purchase or use of the product, regardless of the application. In addition, do not use this product in any way that deviates from the contents of the company's delivery specifications. ■ Unless otherwise specified in this catalog or the product specifications, this product is intended for use in general electronic equipment (AV products, home appliances, commercial equipment, office equipment, information and communication equipment, etc.). When this product is used for the following special cases, the specification document suited to each application shall be signed/sealed (with Panasonic Industry and the user) in advance..These include applications requiring special quality and reliability, wherein their failures or malfunctions may directly threaten human life or cause harm to the human body (e.g.: space/aircraft equipment, transportation/traffic equipment, combustion equipment, medical equipment, disaster prevention/crime prevention equipment, safety equipment, etc.). ■ Please ensure safety through protection circuits, redundant circuits, etc., in the customer's system design so that a defect in our company's product will not endanger human life or cause other serious damage. ■ This catalog shows the quality and performance of individual parts. The durability of parts varies depending on the usage environment and conditions. Therefore, please ensure to evaluate and confirm the state of each part after it has been mounted in your product in the actual operating environment before use. If you have any doubts about the safety of this product, then please notify us immediately, and be sure to conduct a technical review including the above protection circuits and redundant circuits at your company. ■ The transportation of dangerous goods as designated by UN numbers, UN classifications, etc., does not apply to this product. In addition, when exporting products, product specifications, and technical information described in this catalog, please comply with the laws and regulations of the countries to which the products are exported, especially those concerning security export control. ■ Each model of this product complies with the RoHS Directive (Restriction of the use of hazardous substances in electrical and electronic equipment) (2011/65/EU and (EU) 2015/863). The date of compliance with the RoHS Directive and REACH Regulation varies depending on the product model. Further, if you are using product models in stock and are not sure whether or not they comply with the RoHS Directive or REACH Regulation, please contact us by selecting "Sales Inquiry" from the inquiry form. ■ During the manufacturing process of this product and any of its components and materials to be used, Panasonic Industry does not intentionally use ozone-depleting substances stipulated in the Montreal Protocol and specific bromine-based flame retardants such as PBBs (Poly-Brominated Biphenyls) / PBDEs (Poly-Brominated Diphenyl Ethers). In addition, the materials used in this product are all listed as existing chemical substances based on the Act on the Regulation of Manufacture and Evaluation of Chemical Substances. ■ With regard to the disposal of this product, please confirm the disposal method in each country and region where it is incorporated into your company's product and used. ■ The technical information contained in this catalog is intended to show only typical operation and application circuit examples of this product. This catalog does not guarantee that such information does not infringe upon the intellectual property rights of Panasonic Industry or any third party, nor imply that the license of such rights has been granted. ■ Design, materials, or process related to technical owned by Panasonic Industry are subject to change without notice. Panasonic Industry will assume no liability whatsoever if the use of our company's products deviates from the contents of this catalog or does not comply with the precautions. Please be advised of these restrictions. Laws / Regulations / Intellectual property 10-May-24 Safety and Legal Matters to Be Observed Product specifications and applications Safety design and product evaluation

Matters to Be Observed When Using This Product ■ This product (capacitor) is intended for standard general-purpose use in electronic equipment, and is not designed for use in the specific environments described below. Using the product in such specific environments or service conditions, therefore, may affect the performance of the product. Please check with us about the performance and reliability of the product first before using the product. (1) Used in liquid, such as water, oil, chemicals, and organic solvents. (2) Used in a place exposed to direct sunlight, an outdoor place with no shielding, or a dusty place. (3) Used in a wet place (dew concentration on a resistor, water leakage, etc.), a place exposed to sea breeze, or a place filled with a corrosive gas, such as Cl2, H2S, NH3, SO2, or NOX. (4) Used in an environment where static electricity and electromagnetic waves are strong. (5) The product is located close to a heating component or a flammable material, such as a vinyl cable, is placed near the product. (6) The product is used sealed with a resin, etc. (7) Solder flux of the soldered product is cleansed with a solvent, water, and a water-soluble cleaner. (Be careful with water soluble solder flux.) (8) Used in an environment where an acidic or alkali atmosphere is present. (9) Used in an environment where excessive vibration or impact is applied to the product. (10) Used under a low atmospheric pressure condition or depressurized condition. ■ Cleaning can be performed with cleaning agents, including higher-grade alcohol-based cleaning solutions such as Pine Alpha ST-100S, Cleanthru 750H, 750L, 710M, 750K, Techno Care FRW14-17, CFC substitutes such as AK-225AES, and IPA. Please confirm the following precautions before cleaning. (1) Use an immersion, ultrasonic wave, or other cleaning method, and the cleaning time should not exceed 2 minutes. (2) The temperature of the cleaning solution should be less than or equal to 60°C. (3) Control contamination of cleaning agents (conductivity, pH, specific gravity, water content, etc.). (4) After cleaning, do not store the product in the atmosphere of the cleaning solution or in an airtight container. (5) When drying the circuit board or this product, use hot air below the upper limit temperature of their category. (6) Please be mindful that rubbing the printed surface of this product after cleaning may erase the markings depending on the cleaning agent used. (7) Please contact us separately for details on cleaning agents, cleaning methods, etc., and for cleaning solutions other than those listed above. ■ Fixing agents and coating agents (1) Select appropriate materials for the outer packaging and sealing materials of this product. Do not use acetone, especially in fixing agents, coating agents, or diluents. (2) When using a fixing agent or coating agent, ensure that no flux residue or contamination remains between the circuit board and the sealing area of this product. (3) Allow cleaning agents, etc. to dry before using fixing agents or coating agents. (4) Please contact us for thermal curing conditions for fixing agents or coating agents. ■ When the capacitor is used in a circuit where an impact voltage is applied or a high voltage is applied in a short period (transient phenomenon) or a high pulse voltage is applied, make sure to use the capacitor at a voltage equal to or lower than its rated voltage. 30-Jun-23 Use environments and cleaning conditions Matters to Be Observed When Using This Product (Conductive Polymer Aluminum Solid Capacitors / OS-CON)

Matters to Be Observed When Using This Product ■ The main failure mode is a short-circuit mode caused mainly by thermal stress, electrical stress, and mechanical stress due to soldering and operating temperature environments. To prevent the occurrence of short circuits, the following measures should be adequately taken to ensure safety. (1) If odorous gases are generated, then turn off the main power of the set equipment and stop using it. In this case, keep your face and hands away from the equipment. (2) Depending on conditions, it may take several seconds to several minutes before odorous gases are generated. When using a protection circuit, design it so that it operates during this period. (3) If odorous gases get into your eyes or are inhaled, immediately wash your eyes with water or gargle. (4) Do not lick the electrolyte of the product. If the electrolyte gets on your skin, then wash it off with soap. (5) When a current value after the short of the product is extremely large, the shorted capacitor may spark out, which, in the worst scenario, may result in ignition. Ensure the safety of the circuit by, for example, giving it a redundant circuit structure or providing it with a protective circuit. The failure rate of the capacitor is specified based on 0.5%*/1000 h (reliability level 60%), a failure rate conforming to JIS C 5003 (failure rate level). This indicates that the possibility of occurrence of a failure is by no means zero. One of the failure modes is a wear out failure. This happens when the period of guaranteeing the durability and high-temperature/high-humidity resistance of the capacitor is over, changes in the electrical characteristics of the capacitor (product) get larger and its electrolyte gradually deteriorates into an insulating material to create an open mode. Another failure mode is a random failure in which a short mode results mainly because of thermal, electrical, or mechanical stress, etc. ■ Due to reasons such as increased leakage currents, do not use this product in high impedance circuits, coupling circuits, time constant circuits, and circuits that are significantly affected by leakage currents. ■ During circuit design, be mindful that the electrical characteristics of this product, such as capacitance and ESR, may fluctuate within the specified ranges even under conditions that meet the rated electrical and mechanical performance. ■ Leakage currents may increase due to mechanical and thermal stress (soldering, high-temperature no-load test, etc.). However, when the voltage (lower than or equal to the category voltage and upper limit temperature) is applied, leakage currents gradually decrease due to the self-recovery function. ■ If an excessive rush current flows due to rapid charging and discharging, then it may lead to short circuits and increased leakage currents. Therefore, apply a protection circuit to this product if the rush current value flowing through it is as follows. (1) When a rush current of 10 A or more flows through a product whose tenfold allowable ripple current is less than 10 A. (2) With regard to a product whose tenfold allowable ripple current is 10 A or more, when a rush current exceeding the tenfold value flows through the product. ■ The resin on the surface of the case does not guarantee insulation. In addition, there is an indefinite resistance between the case and the cathode terminal, and they are not insulated. Therefore, completely isolate the case from the cathode terminal, anode terminal, and circuit pattern. ■ Soldering with a soldering iron (1) Since the lead wire pitch dimension of the radial lead type capacitor and the printed circuit board hole pitch dimension do not match, when processing the lead wires, do not apply stress to the body before soldering. (2) When soldering, do not apply excessive stress to the body of this product. (3) Once the product has been soldered, when using a soldering iron to remove it, remove it after the solder has completely melted so as not to apply stress to the electrode terminals of the product. (4) Do not allow the tip of the soldering iron to touch the body of this product. 30-Jun-23 Reliability and product life Circuit design and circuit board design Mounting and storage conditions Response to anomalies and handling conditions

Matters to Be Observed When Using This Product / Reference Information ■ Flow soldering (1) Do not apply flow soldering to the surface mount type model of this product. (2) Do not solder this product by immersing its body in molten solder. (3) Solder only on the opposite side of the circuit board surface where this product is mounted. (4) Do not allow flux to adhere to parts other than the electrode terminals. (5) Do not allow other parts to fall over and come into contact with this product during soldering. ■ Reflow soldering (1) Do not apply reflow soldering to the radial lead type model of this product. (2) Please contact us separately for soldering conditions for using the VPS method. ■ Handling after soldering Observe the following precautions to avoid applying excessive stress on this product. (1) Do not tilt, knock over, or twist this product. (2) Do not move the circuit board by grabbing this product. (3) Do not hit this product with objects. (4) When stacking circuit boards, do not allow circuit boards or other parts to come in contact with this product. ■ It is recommended that all components in the bag be used up by opening the bag immediately before use. However, if the remaining components are to be stored after opening the bag, please use them up within the following specified period* to maintain good solderability. * The surface mount type does not comply with the JEDEC J-STD-020 specification. (1) Surface mount type : Within 24 months after shipment (before opening) and within 30 days after opening (packaged with carrier tape) (2) Radial lead type (bagged product) : Within 30 months after shipment (before opening) and within 7 days after opening (3) Radial lead type (taped product) : Within 24 months after shipment (before opening) and within 7 days after opening Panasonic Group provides customers with safe products and services. We are also making great efforts to protect our intellectual property rights for Panasonic Group products. Typical patents related to this product are as follows. [U.S. patent] USP No. 7158367 30-Jun-23 Reference information Intellectual property