6014CT MALLORY | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 8
Technical content
MSD • WWW.MSDPERFORMANCE.COM • (915) 855-7123 • FAX (915) 857-3344 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with your product and helps the MSD R&D team create new products that you ask for! Go to www.msdperformance.com/registration. MSD Circle Track LS Ignition Control PN 6014CT Parts Included: 1 – Ignition Control, PN 6014CT 1 – Main Wiring Harness 1 – Sub Harness 1 – Crank/Cam Pigtail 24x/1x 1 – Crank/Cam Pigtail 58x/4x 1 – USB Cable 1 – Mounting Kit 1 – MSDView USB Flash Drive WARNING: During installation, disconnect the battery cables. When disconnecting, always re - move the negative cable first and install it last. Note: Solid core spark plug wires cannot be used with an MSD Ignition Control. OPERATION The MSD 6014CT LS Ignition controller works with 24x/1x, 58x/4x and 58x/1x crank/cam configura- tions. It auto detects the correct configuration based on the crankshaft reluctor wheel pattern, so there is no need to select one. It provides a customizable timing plot that can be programmed via MSDView. Note: It is recommended, that you install and run MSDView software while connected to the unit to perform the base settings. The unit can be powered via the USB cable, so this can be done from a desktop or laptop and does not require an external power source.
2 INSTALLATION INSTRUCTIONS
MSD • WWW.MSDPERFORMANCE.COM • (915) 855-7123 • FAX (915) 857-3344 RED Ignition 12V supply. From battery (via relay) or dedicated fused 30A switch. BLACK Battery Negative CAM/CRANK SENSOR - 10 PIN ORANGE/YELLOW Pin-1 Crank Signal BROWN/WHITE Pin-2 Cam Signal ORANGE Pin-3 5-volt supply PINK Pin-4 12-volt supply BROWN Pin-6 Sensor Ground GRAY Tach Provides a 12-volt square wave signal. COIL CONNECTOR - EVEN CYLINDERS BLACK Pin-A Engine Ground RED/GREEN Pin-B Coil 2 BROWN/GREEN Pin-C Coil 4 Pin-D Not Used BROWN Pin-E Sensor Ground WHITE/BLUE Pin-F Coil 6 VIOLET/BLUE Pin-G Coil 8 PINK Pin-H 12-volt supply for even cylinder coils COIL CONNECTOR - ODD CYLINDERS BLACK Pin-A Engine Ground RED Pin-B Coil 7 GREEN Pin-C Coil 5 Pin-D Not Used BROWN Pin-E Sensor Ground BLUE Pin-F Coil 3 VIOLET Pin-G Coil 1 PINK Pin-H 12-volt supply for odd cylinder coils WIRING FEATURES
INSTALLATION INSTRUCTIONS 3 MSD • WWW.MSDPERFORMANCE.COM • (915) 855-7123 • FAX (915) 857-3344 PIN FUNCTION COLOR A NOT USED B Sensor Ground BROWN C Coil 2 RED/GREEN D Coil 4 BROWN/GREEN E Coil 6 WHITE/BLUE F Coil 8 VIOLET/BLUE G 12V Supply PINK H Main 12V Supply RED J Ground BLACK K 12V Supply PINK L Coil 7 RED M Coil 5 GREEN N Coil 3 BLUE P Coil 1 VIOLET R Sensor Ground BROWN S NOT USED PIN FUNCTION COLOR A 12V Sensor Power PINK B Ground BROWN C Cam BROWN/WHITE D Crank ORANGE/YELLOW E 5V Sensor Power ORANGE F Factory Use BLACK G NOT USED H NOT USED J NOT USED K Tach GRAY 16-Pin Connector 10-Pin Connector Connect to Passenger's side coil connector. (Coils 2-4-6-8) Connect to a ground source. Connect to Driver's side coil connector. (Coils 1-3-5-7) Connect to Relay or dedicated fused 30A switch. Connect to Cam/Crank pigtail. Tach output
4 INSTALLATION INSTRUCTIONS
MSD • WWW.MSDPERFORMANCE.COM • (915) 855-7123 • FAX (915) 857-3344 USB (MINI) TO MAIN HARNESS (POWER &COILS) TO CAM/CRANK HARNESS TO RACE IGNITION TEST TOOL DIAGNOSTIC CONNECTOR CAP DIAGNOSTIC CONNECTOR Figure 1 LS Ignition Controller, PN 6014CT EFGH E F G H CYL 2-4-6-8 CYL 1-3-5-7 CAM/CRANK A B C A B C CRANK CAM IGNITION (30A FUSED) GROUND COILS 1-3-5-7 COILS 2-4-6-8 CRANKCAM/CRANK CAM CAM/CRANK NOTE: CAM PLUGS DIRECTLY INTO SENSOR, NOT OEM PIGTAIL. 22791 - 24x CRANK CAM (REAR) - INCLUDED BLACK CRANK SENSOR CONNECTOR BLACK CAM SENSOR CONNECTOR 2278 - 58x CRANK/4x CAM (FRONT) - INCLUDED GRAY CRANK SENSOR CONNECTOR BLACK CAM SENSOR CONNECTOR Figure 2 LS Ignition Controller Harnesses, PN 6014CT Note: The PN 6014CT LS Ignition Controller requires a 30 Amp fused power source. Do not power the unit directly through the ignition key switch.
6 INSTALLATION INSTRUCTIONS
MSD • WWW.MSDPERFORMANCE.COM • (915) 855-7123 • FAX (915) 857-3344 INSTALLATION OF THE MSDVIEW SOFTWARE 1. Insert the installation Flash Drive into an available USB port. 2. Locate the ‘autorun.exe’ file on the Flash Drive. 3. Click on “Install MSD View Software.” Click ‘Yes’ when asked ‘Do you want the following program to make changes to this computer?’. 4. Click ‘Next’ in the ‘Setup - MSD View’ window. Accept the License Agreement and click ‘Next’. Choose to accept the desktop icon then click ‘Install’. Click ‘Finish’ to run the application. 5. Connect the LS Controller via USB and wait for it to be listed in the product window. It will be listed in the product window. Select the LS Controller by highlighting the line or checking the box and clicking the ‘View/Hide’ button. Note: The first time the unit is connected, it may prompt for updates to be installed. SAVES AND TRANSFERS Changes made to the Circle Track LS Ignition Controller via MSDView are in real time. You can create and save numerous different files to your PC and load them back into the unit for different applications. The following will go through a general description of the software for the Circle Track LS Ignition Controller. PROGRAMMABLE FEATURES AND SETTINGS These are basic settings that should be configured the first time the unit is used, but it is not required. A basic setup can be performed on the bench with just the USB cable connected to the device. No external power is required. Maximum Rev Limiter: This is the maximum RPM that the engine can reach before the Rev limiter becomes active. Coil Type: This selects the dwell or charge time of the coils. Choose “AUTO” if unsure. Auto – The controller will automatically match the coil dwell to the crankshaft reluctor wheel used. LS1 – This sets the dwell time of the LS1/6 coils. LS2/3/7 – This sets the dwell time of the LS2/3/7 coils. Truck – This sets the dwell time of the early truck coils. TIMING Under this tab, you will find the timing plot used to control the spark output. The ignition spark timing is a function of the Engine Speed. The user can modify the plot points, add additional points or remove unnecessary points. REGULATED Under this tab, you will find the settings that can be regulated by sanctioning bodies. When a particular setting is predetermined by a sanctioning body, the appropriate setting should be checked in the REGULATED tab. These settings should also match the predetermined values as prescribed by the sanctioning body. This feature allows the use of the Test Tool to verify compliance. When the Test Tool is connected via the Diagnostic Connector it will read the regulated parameters from the unit and compare them to the specified values. A match in of all the REGULATED parameters indicates compliance, while a mismatch indicates noncompliance. Normally, it is the responsibility of the racer to enter the REGULATED parameters in accordance with sanctioning body rules.
INSTALLATION INSTRUCTIONS 7 MSD • WWW.MSDPERFORMANCE.COM • (915) 855-7123 • FAX (915) 857-3344 Figure 5 Custom Timing Table 1 MONITORS MONITORS Description ENGINE SPEED Engine speed in RPM IGNITION TIMING Ignition timing referenced to Top Dead Center (TDC) IGNITION VOLTAGE This is the voltage being supplied to the unit. This is also the voltage being supplied to the coils - so it is important that it remains over 12V to ensure optimum engine performance. REV LIMITER SOURCE Indicates which source will be limiting the motor. It will be "Key Off" when connected via USB, or "Maximum" any other time. ALERTS FAULTS Description/Cause BATTERY Activates if voltage drops below 9V or goes above 18V CAM FAULT RPM is detected, but no cam sensor signal is present CRANK FAULT Camshaft sensor signal is present, but no engine speed is detected via the crankshaft sensor. EEPROM READ ERROR EEPROM data corrupted EEPROM WRITE ERROR Error writing to EEPROM
8 INSTALLATION INSTRUCTIONS
MSD warrants this product to be free from defects in material and workmanship under its intended normal use*, when properly installed and purchased from an authorized MSD dealer, for a period of one year from the date of the original purchase. This warranty is void for any products purchased through auction websites. If found to be defective as mentioned above, it will be repaired or replaced at the option of MSD. Any item that is covered under this warranty will be returned free of charge using Ground shipping methods. This shall constitute the sole remedy of the purchaser and the sole liability of MSD. To the extent permitted by law, the foregoing is exclusive and in lieu of all other warranties or representation whether expressed or implied, including any implied warranty of merchantability or fitness. In no event shall MSD or its suppliers be liable for special or consequential damages. *Intended normal use means that this item is being used as was originally intended and for the original application as sold by MSD. Any modifications to this item or if it is used on an application other than what MSD markets the product, the warranty will be void. It is the sole responsibility of the customer to determine that this item will work for the application they are intending. MSD will accept no liability for custom applications. Service In case of malfunction, this MSD component will be repaired free of charge according to the terms of the warranty. When returning MSD components for warranty service, Proof of Purchase must be supplied for verification. After the warranty period has expired, repair service is based on a minimum and maximum fee. All returns must have a Return Material Authorization (RMA) number issued to them before being returned. To obtain an RMA number please contact MSD Customer Service at 1 (888) MSD-7859 or visit our website at www.msdperformance.com/rma to automatically obtain a number and shipping information. When returning the unit for repair, leave all wires at the length in which you have them installed. Be sure to include a detailed account of any problems experienced, and what components and accessories are installed on the vehicle. The repaired unit will be returned as soon as possible using Ground shipping methods (ground shipping is covered by warranty). For more information, call MSD at (915) 855-7123. MSD technicians are available from 7:00 a.m. to 5:00 p.m. Monday - Friday (mountain time). MSD • WWW.MSDPERFORMANCE.COM • (915) 857-5200 • FAX (915) 857-3344 © 2017 MSD LLC FRM 34444 Created 01/17 TECH NOTES