53217 MICROPAC | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 6
Technical content
Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement. Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible. MICROPAC INDUSTRIES, INC. MICROCIRCUITS PRODUCTS DIVISION • 905 E. Walnut St., Garland, TX 75040 • (972) 272-3571 • Fax (972) 494-2281 www.micropac.com E-MAIL: hybridsales@micropac.com 8/12/02 Pg. 1 of 6
53217 SPST SOLID-STATE POWER CONTROLLERS
Features:
- Short circuit protection with status output
- SPST, normally open
- Up to 1000 V RMS isolation
- Output current up to 3 Amps DC
- Power FET output
- Low on-state resistance
- Full military temperature operation: -55ºC to +125ºC
- Military environmental screening available Applications:
- Ideal for 270V bus applications
- Aircraft Power Distribution
- Military/High Reliability Systems
- Satellite/Space Systems
DESCRIPTION
The 53217 is a military SPST high power, solid-state relay. It is a light-weight device re sistant to damage from shock and vibration, and immune to contact-related problems (contamination, arcing) associated with mechanical equivalents. Transformer coupling between the input and output stages provides effective isolation up to 1000 V RMS. The Power FET output eliminates bipolar offset and minimizes output voltage drop. The control input may be driven by either CMOS or TTL logic, and the bias supply will accommodate 3.8 through 32 VDC. (See figures 1 & 2) Integral short-circuit protection with status output is provided. These units sense excessive current flow while under load or while switching, and respond by opening the output. An open-collector status output is available to indicate that the short circuit protection has been activated. The output will remain blocked indefinitely until the short is removed and the unit reset. This feature prevents damage to the controller and also averts further system failures that may be caused by the short circuit. Status line output remains on until the relay is turned off for resetting. Resetting the unit can be accomplished by recycling the input control. This device is available in a variety of quality levels from COTS to class K including any custom screening requirements. The basic data sheet part is environmentally screened to H level in accordance with Table C-IX of MIL-PRF-38534, which includes no element evaluation or QCI. ABSOLUTE MAXIMUM RATINGS Notes: 1 60 Hz sine wave
2 At TC = 125ºC max
3 Reversing polarity on the output may cause permanent damage
4 Devices will not tolerate “short while on” at load voltages exceeding 28 VDC
Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement. Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible. MICROPAC INDUSTRIES, INC. MICROCIRCUITS PRODUCTS DIVISION • 905 E. Walnut St., Garland, TX 75040 • (972) 272-3571 • Fax (972) 494-2281 www.micropac.com E-MAIL: hybridsales@micropac.com 8/12/02 Pg. 2 of 6 53217 SPST SOLID-STATE POWER CONTROLLERS
ELECTRICAL CHARACTERISTICS
TA = +25° C PARAMETER TEST CONDITIONS MIN TYP MAX UNITS Input characteristics CMOS configurations (Figure 1) Bias supply range, VDD 3.8 32 VDC Bias current 3 5 mA Input current 5 VDC Input 250 µA Control voltage range 3.8 18 VDC Turn-off voltage 2.8 VDC Turn-on voltage 0.5 VDC Total Hysteresis 1.8 VDC Dielectric strength 60 Hz 1000 V RMS Input characteristics TTL configuration (Figure 2) Input current 3 5 mA Control voltage range 3.8 32 VDC Turn-off voltage Note 5 1.5 VDC Turn-on voltage Note 5 3.8 VDC Status on voltage On at 5 mA SINKING CURRENT 0.4 Volts Status off leakage Off at 20 V 20 µA Output characteristics Output current:: At TC = 125ºC case temperature 3.0 A Continuous blocking voltage
400 VDC
On-state resistance, Rds 25ºC Case 0.50 Ohms Turn-on time @ 25ºC case 0.4 0.8 ms Turn-off time @ 25ºC case 0.5 2.0 ms Off-state leakage At Maximum Blocking Voltage 40 100 µA Output Capacitance 700 pF Short-circuit current 25ºC 6 A Short-circuit peak Shorted while on at 25ºC See Figure 3 100 A Junction temperature 150 ºC Thermal resistance, θJA θJC ºC/W ºC/W APPLICATION NOTES: 1. Maximum input switching frequency not to exceed 20 Hz under normal conditions, or 1 Hz if output is shorted. 2. Input transitions should be <1 ms and duration and input source should be “bounceless contact” type. 3. Inductive loads must be diode suppressed. 4. Peak current that may flow when output is shorted. 5. Devices will not tolerate “short while on” at load voltages exceeding 28 VDC.
Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement. Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible. MICROPAC INDUSTRIES, INC. MICROCIRCUITS PRODUCTS DIVISION • 905 E. Walnut St., Garland, TX 75040 • (972) 272-3571 • Fax (972) 494-2281 www.micropac.com E-MAIL: hybridsales@micropac.com 8/12/02 Pg. 5 of 6 53217 SPST SOLID-STATE POWER CONTROLLERS CONTROL OFF ON ON OFF 3 A IOUT STATUS OFF ON SIMULATED SHORT Figure 5 - TIMING DIAGRAM
Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement. Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible. MICROPAC INDUSTRIES, INC. MICROCIRCUITS PRODUCTS DIVISION • 905 E. Walnut St., Garland, TX 75040 • (972) 272-3571 • Fax (972) 494-2281 www.micropac.com E-MAIL: hybridsales@micropac.com 8/12/02 Pg. 6 of 6 .735 (.060) (1.390) .240 MAX. 1.000 .600 .800 .200 TOL: ±.010 (BOTTOM VIEW) .200 .400 22 16 1.450 1.750 2.100 .45 MIN. Ø.157
2 PLACES
Ø.040, 6 PLACES .795 53217 SPST SOLID-STATE POWER CONTROLLERS Package Dimensions IN FUNCTION