53111 MICROPAC | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 11

Technical content

Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement. Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible. MICROPAC INDUSTRIES, INC. MICROCS PRODUCTS DIVISION • 905 E. Walnut St., Garland, TX 75040 • (972) 272-3571 • Fax (972) 494-2281 www.micropac.com E-MAIL: hybridsales@micropac.com 5/22/02 Pg. 1 of 11

53111 POWER MOSFET OPTOCOUPLER,

90 V/1 Ω, Hermetically Sealed,

DSCC Approved 5962-9314001 and 5962-9314002 Mii MICROCIRCUITS PRODUCTS DIVISION Features:

  • Hermetically Sealed 8-Pin Dual-In-Line package
  • Small Size and Weight
  • Options: 5mA or 10mA input forward current
  • Performance Guaranteed over –55°C to +125°C Ambient Temperature Range
  • AC/DC Signal & Power Switching
  • Maximum Average Current AC/DC: 0.8 A DC only: 1.6 A
  • 1500 VDC Withstand Test Voltage
  • High Transient Immunity
  • 5 A Output Surge Current
  • Shock and Vibration Resistant
  • MIL-PRF-38534 Compliant
  • Equivalent to HSSR7111/7112 Applications:
  • Satellite/Space Systems
  • Military/High Reliability Systems
  • Standard 28 VDC and 48 VDC Load Driver
  • Standard 24 VAC Load Driver
  • AC/DC Electromechanical and Solid State Relay Replacement
  • I/O Modules

DESCRIPTION

The 53111 is a single channel, hermetically sealed, power MOSFET optocoupler. Low on-resistance of the MOSFET output, combined with 1500 VDC isolation between input and output, makes this optocoupler ideal for solid state relay applications. Operation is specified over the full military temperature range. The part is supplied in an eight-pin, dual-in-line ceramic package, available as CO TS, as fully compliant MIL- PRF-38534 Class H device, or with custom screening. Lead options support both th rough-hole and surface-mount assembly. The part is normally shipped with gold plated leads, but lead finishes per MIL-PRF-38534 are available. Functionally, the device operates as a single-pole, normally open (1 Form A) solid state relay. The device is actuated by an input current, which can be supplied from standard logic types such as open-collector TTL. The input current biases a light emitting di ode that is optically coupled to an in tegrated photovoltaic diode array. The photovoltaic array powers control circuitry that operates the output MOSFETs. Optimum switching of either AC or DC loads is provi ded by a configurable output. For AC loads, connection A in Figure 1 must be used. Connection A will also switch DC lo ads but connection B, in Figure 1, provides DC-only operation with the advantages of subst antial reduction in on-resistance and twice the output current capability as that obtained with connection A.

Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement. Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible. MICROPAC INDUSTRIES, INC. MICROCS PRODUCTS DIVISION • 905 E. Walnut St., Garland, TX 75040 • (972) 272-3571 • Fax (972) 494-2281 www.micropac.com E-MAIL: hybridsales@micropac.com 5/22/02 Pg. 2 of 11

53111 Power MOSFET Optocoupler

Single Shot Output Current - Figure 4 Output Voltage RECOMMENDED OPERATING CONDITIONS: PARAMETER SYMBOL DEVICE TYPE MIN MAX UNITS -01 10 20 mA Input Current (on) IF (ON) -02 5 20 mA Input Voltage (off) V F (OFF) All 0 0.6 VDC Operating Temperature T A All -55 +125 °C

Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement. Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible. MICROPAC INDUSTRIES, INC. MICROCS PRODUCTS DIVISION • 905 E. Walnut St., Garland, TX 75040 • (972) 272-3571 • Fax (972) 494-2281 www.micropac.com E-MAIL: hybridsales@micropac.com 5/22/02 Pg. 3 of 11 TA = -55°C to +125°C, unless otherwise specified. Parameter Sym. Min. Typ.* Max. Units Test Conditions Notes Output Withstand Voltage V O(OFF) 90 110 V VF = 0.6 V IO = 10 µA Output On-Resistance (Connection A) 0.40 1.0 Ω I F = 10 mA (for –01) IF = 5 mA (for –02) IO = 800 mA (pulse duration ≤ 30 ms) Output On-Resistance (Connection B) R(ON) 0.12 0.25 Ω IF = 10 mA (for –01) IF = 5 mA (for –02) IO = 1.6 A (pulse duration ≤ 30 ms) Figure Output Leakage Current I O (OFF) 10 -4 10 µA VF = 0.6 V VO = 90 V Input Forward Voltage V F 1.0 1.24 1.7 V IF = 10 mA (for –01) IF = 5 mA (for –02) Input Reverse Breakdown Voltage VR 5.0 V IR = 100 µA Input-Output Insulation I I-O 1.0 µA RH ≤ 45%, t = 5 s VI-O = 1500 VDC TA = 25°C 4, 5 Turn-On Time t ON 1.25 6.0 ms IF = 10 mA (for –01) IF = 5 mA (for –02) VDD = 28 VDC IO = 800 mA Figure Turn-Off time t OFF 0.02 0.25 ms IF = 10 mA (for –01) IF = 5 mA (for –02) VDD = 28 VDC IO = 800 mA Figure Output Transient Rejection dV O/dt 1000 V/µs VPEAK = 50 V CM = 1000 pF CL = 15 pF RM ≥ 1 MΩ Figure Input-Output Transient Rejection dV I-O/dt 500 V/µs VDD = 5 V VI-O (PEAK) = 50 V RL = 20 kΩ CL = 15 pF Figure * All typical values are at TA = 25ºC, IF (ON) = 10 mA (for -01) or 5 mA (for –02), VF (OFF) = 0.6V unless otherwise specified.

Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement. Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible. MICROPAC INDUSTRIES, INC. MICROCS PRODUCTS DIVISION • 905 E. Walnut St., Garland, TX 75040 • (972) 272-3571 • Fax (972) 494-2281 www.micropac.com E-MAIL: hybridsales@micropac.com 5/22/02 Pg. 4 of 11 All typical values are at TA = 25°C, IF (ON) = 10mA, VF (OFF) = 0.6V unless otherwise specified. Parameter Symbol Test Conditions Typ. Units Notes Output Off-Capacitance C O (OFF) VO = 28 V f = 1 MHz 145 pF Output Offset Voltage V OS IF = 10 mA IO = 0 mA 2 µV 6 Input Diode Temperature Coefficient ∆VF /∆TA IF = 10 mA -1.4 mV/°C Input Capacitance C IN VF = 0 V f = 1 MHz 20 pF 7 Input-Output Capacitance CI-O VI-O = 0 V f = 1 MHz 1.5 pF 4 Input-Output Resistance R I-O VI-O = 500 V t = 60 s 1013 Ω 4 Notes: 1. Maximum junction to case thermal resistance for the device is 15ºC/W, where case temperature, TC, is measured at the center of the package bottom. 2. For rating, see Figure 5. The output power P D rating curve is obtained when the part is handling the maximum average output current IO as shown in Figure 3. 3. During the pulsed R ON measurement (IO duration < 30 ms), ambient (TA) and case temperature (TC) are equal. 4. Pins 2 through 3 shorted together and pins 5 through 8 shorted together. 5. This is a momentary withstand test, not an operating condition. 6. V OS is a function of IF and is defined between pins 5 and 8, with pin 5 as the reference. VOS must be measured in a stable ambient (free of temperature gradients). 7. Zero-bias capacitance measured between the LED anode and cathode. CAUTION: Care should be taken not to exceed the maximum output power dissipation, maximum case temperature, and maximum junction temperature when repetitively switching loads.

Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement. Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible. MICROPAC INDUSTRIES, INC. MICROCS PRODUCTS DIVISION • 905 E. Walnut St., Garland, TX 75040 • (972) 272-3571 • Fax (972) 494-2281 www.micropac.com E-MAIL: hybridsales@micropac.com 5/22/02 Pg. 5 of 11 F Figure 1 - Terminal Connections 5 4 5 CONNECTION B DC CONNECTION Case outlines P, X, Y, AND Z Terminal number Terminal symbol Connection A Conneciton B (AC or DC load) (DC load only) NC = No connection I FV OI OV FI FV VO OI V NC V NC V NC NC V F-V NC VO+ O-N V O+ NC NC VF+ Figure 2 - Truth Table ON ON OFF OFF INPUT OUTPUT

Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement. Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible. Figure 3. Maximum Average Output Current Figure 4. Single Shot (nonrepetitive) Rating vs. Ambient Temperature. Output Current vs. Pulse Duration. Figure 5. Output Power Rating vs. Ambient Temperature.

Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement. Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible.

  1. PULSE GENERATOR HAS THE FOLLOWING CHARACTERISTICS: OUTPUT IMPEDANCE = 50
  2. LOAD CAPACITANCE (C ) INCLUDES PROBE AND JIG CAPACITANCE.

Figure 6. Switching Test Circuit and Waveform.

Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement. Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible.

  1. C INCLUDES PROBE AND FIXTURE CAPACITANCE.
  2. R INCLUDES PROBE AND FIXTURE RESISTANCE.

Figure 7. Output Transient Rejection Test Circuit and Waveform.

Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement. Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible.

  1. FOR DEVICE TYPE 01, I =10mA,
  2. LOAD CAPACITANCE (C )INCLUDES PROBE AND FIXTURE CAPACITANCE.

Figure 8. Input-Output Transient Rejection Test Circuit and Waveform.

Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement. Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible. MICROPAC INDUSTRIES, INC. MICROCS PRODUCTS DIVISION • 905 E. Walnut St., Garland, TX 75040 • (972) 272-3571 • Fax (972) 494-2281 www.micropac.com E-MAIL: hybridsales@micropac.com 5/22/02 Pg. 10 of 11 .050 (1.27) .035 (0.89) .050 (1.27) .035 (0.89) .050 (1.27) .035 (0.89) .110 (2.79) .370 (9.41) .390 (9.91) .370 (9.41) .110 (2.79) .090 (2.29) .110 (2.79) .090 (2.29) .020 (0.51) MAX. .020 (.051) MAX. .020 (0.51) MAX. .050 (1.27) .030 (0.76) .020 (0.51) MIN .065 (1.65) .055 (1.40) .020 (0.51) MIN .055 (1.40) .045 (1.14) .020 (0.51) MIN .013 (0.33) .007 (0.18) .150 (3.81) MIN. .390 (9.91) .370 (9.41) SEATING PLANE .180 (4.57) MAX .013 (0.33) .007 (0.18) .170 (4.32) MAX. .320 (8.13) MAX .310 (7.87) .290 (7.37) .170 (4.32) MAX. .170 (4.32) MAX. .047 (1.19) TYP .390 (9.91) .380 (7.87) .320 (8.13) MAX SEATING PLANE PIN 1 SYMBOL ESD .310 (7.87) .290 (7.37) .320 (8.13) MAX.

31757 USA

Q Case Outline P Case Outline X Case Outline Y NOTES: 1. PIN 1 IS INDICATED BY THE ESD TRIANGLE MARKED ON THE LID OF THE PACKAGE. 2. DIMENSIONS ARE IN INCHES, (mm). 3. METRIC EQUIVALENTS ARE GIVEN FOR GENERAL INFORMATION ONLY. 4. UNLESS OTHERWISE SPECIFIED, TOLERANCE IS ±.005 (0.13mm). .140 (3.56) MAX. .050 (1.27) .035 (0.89) SEATING PLANE .045 (1.14) .035 (0.89) .110 (2.79) .090 (2.29) .390 (9.91) .370 (9.41) .320 (8.13) MAX .013 (0.33) .007 (0.18) .310 (7.87) .290 (7.37) Case Outline Z

Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement. Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible. MICROPAC INDUSTRIES, INC. MICROCS PRODUCTS DIVISION • 905 E. Walnut St., Garland, TX 75040 • (972) 272-3571 • Fax (972) 494-2281 www.micropac.com E-MAIL: hybridsales@micropac.com 5/22/02 Pg. 11 of 11 The followings are the cross-reference of Micropac part numbers versus Standard Military PIN. Please contact Micropac for other desired options. Micropac Part Number Standard Milit ary Drawing PIN Case Outline 53111-1PA 5962-9314001HPA P 53111-1PC 5962-9314001HPC P 53111-1XA 5962-9314001HXA X 53111-1XC 5962-9314001HXC X 53111-1YA 5962-9314001HYA Y 53111-1YC 5962-9314001HYC Y 53111-1ZA 5962-9314001HZA Z 53111-1ZC 5962-9314001HZC Z 53111-2PA 5962-9314002HPA P 53111-2PC 5962-9314002HPC P 53111-2XA 5962-9314002HXA X 53111-2XC 5962-9314002HXC X 53111-2YA 5962-9314002HYA Y 53111-2YC 5962-9314002HYC Y 53111-2ZA 5962-9314002HZA Z 53111-2ZC 5962-9314002HZC Z