5116

5116 CONNOR-WINFIELD | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 2

Technical content

Specifications subject to change without notice. All dimensions in inches. © Copyright 1998 The Connor-Winfield Corporation

2111 Comprehensive Drive

Aurora, Illinois 60505 Phone: 630-851- 4722 Fax: 630- 851- 5040 www.conwin.com Aurora, Illinois 60505 Phone: 630-851-4722 Fax: 630- 851- 5040 www.conwin.com 2.8V LVCMOS Surface Mount Crystal Clock Oscillator 5116 XO The Connor-Winfield models 5116, 5126, and 5136 are 7.5mm x 5mm, 2.8V LVCMOS, Surface Mount, Fixed Frequency Crystal Oscillators (XO) designed for use in all applications requiring precision clocks. This oscillator features low stand-by current (10uA) when the output is disabled. The RoHS compliant, surface mount package is designed for high-density mounting and is optimum for mass production. Operating Specifications Parameter Minimum Nominal Maximum Units Notes Frequency Range (Fo) 1.8 - 80 MHz Frequency Tolerance - ppm 1 5116 -25 25 5126 -50 50 5136 -100 100 Operating Temp Range 0 - 70 °C Supply Voltage (Vdd) 2.66 2.8 2.94 Vdc Supply Current (Icc) 1.8 to 31.999 MHz - - 12 mA32 to 50 MHz - - 20 Absolute Maximum Ratings Parameter Minimum Nominal Maximum Units Notes Storage Temperature -55 - 125 °C Supply Voltage (Vcc) -0.5 - 7.0 Vdc Features: 1.8 to 80 MHz 2.8V Operation RoHS Compliant Tri-State Enable / Disable Function Overall Frequency Tolerance: 5116 ± 25 ppm, 5126 ± 50 ppm, 5136 ± 100 ppm Temperature Range: 0 to 70°C Power Saving Stand-By Current Ceramic Surface Mount Package Tape and Reel Packaging Bulletin Sm075 Page 1 of 2 Revision 01 Date 15 April 2002 Input Characteristics Parameter Minimum Nominal Maximum Units Notes Enable Voltage - (Vih) ≥ 70% Vdd - - Vdc 2 Disable Voltage - (Vil) - - ≤ 30% Vdd Vdc Enable Time - - 10 nS Disable Time - - 150 nS Output Disable Current (lcc) - - 10 uA HCMOS Output Characteristics Parameter Minimum Nominal Maximum Units Notes Load - - 15 pF Voltage High (Voh) 2.39 - - VdcLow (Vol) - - 0.29 Current High (loh) -4 - - mALow (lol) - - 4 Duty Cycle at 50% of Vcc 45 50 55 % Rise / Fall Time 10% to 90% - - 5 nS Start-Up Time - - 10 mS Jitter - - 5 pS RMS Notes: 1. Inclusive of calibration @ 25°C , frequency vs temperature stability, supply voltage change, load change, shock and vibration, 10 years aging. 2. Oscillator requires a pull up resistor from pin 1 to Vcc to insure proper operation. US Headquarters: 630-851-4722 European Headquarters: +353-61-472221

Specifications subject to change without notice. All dimensions in inches. © Copyright 1998 The Connor-Winfield Corporation Aurora, Illinois 60505 Phone: 630-851-4722 Fax: 630- 851- 5040 www.conwin.com Bulletin Sm075 Page 2 of 2 Revision 01 Date 15 April 2002 Pin Connections 1: Enable/Disable 2: Ground 3: Output 4: Vcc OSCILLOSCOPE FREQ COUNTER OSC POWER SUPPL Y INPUT FOR E/D PROBE Meets EIA-481A and EIAJ-1009B 2,000 PCS/Reel Bypass capacitor, C-by, should be ceramic capacitor ≥ .01 uf SYMMETRY Soldering General Conditions 260°C max x 10 sec max x 2 times max or 230°C max x 180 sec max x 1 time Typical Operation Data (Vapor phase reflow) 20 to 100 sec up to 215°C, 50 sec at 215°C, then down to room temperature per 1 to 5°C / sec Environmental Characteristics Temperature Cycle The specimen shall meet electrical characteristics after tested 5 cycles of -55°C / 30 minutes and +125°C / 30 minutes Hermetical No bubbles appear in Flourinert (FC-43) at 125°C ±5°C for 5 minutes Solvent Resistance Marking will withstand immersion in Isopropyl Alcohol or Trichloroethylene Suggested Pad Layout

Ordering Information

5116 - 77.76 MHz CLOCK SERIES CENTER FREQUENCY Mechanical Characteristics Free Drop The specimen shall meet electrical characteristics after tested 3 times, Free Drop testing on the hard wooden board from a height of 75 cm. Vibration The specimen shall meet electrical characteristics after tested by the following conditions: 10-55Hz 1.5mm Amplitude, 55-2000 Hz 20 G's, 2 hours for each plane Thermal Shock After applied Thermal Shock of 260°C max x 10 sec max x 2 times, or 230°C max x 180 sec max, the specimen shall meet electrical characteristics Solderability (EIAJ-RCX-0102.101 Condition 1a) 1) Flux: MIL-F-14256 (WW Rosin=25%, Isopropyl Alcohol = 75%) 2) Solder: QQ-S-571 (Sn = 63%, Pb = 37%) 3) Solder bath temperature: 235°C ±5°C 4) Depth of immersion: Up to electrical terminal 5) Immersing time: Within 2 sec ±0.5 sec into solder bath After performing the above procedures, a newly soldered coverage shall be greater than 90%After performing the above procedures, a newly soldered coverage shall be greater than 90%After performing the above procedures, a newly soldered coverage shall be greater than 90%After performing the above procedures, a newly soldered coverage shall be greater than 90%After performing the above procedures, a newly soldered coverage shall be greater than 90% Test Circuit Output Waveform Tape and Reel Dimensions Package Characteristics Package Hermetically sealed ceramic package and metal cover Dimensional Tolerance: ±.02"(.508mm) ±.005"(.127mm)