40DAWE GAPTEC | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 5

Technical content

GAPTEC-Electronic GmbH & Co. KG sales@gaptec-electronic.com – www.gaptec-electronic.com Page 1 of 5 40DAWE_1.5 – Rev. 2020-1.2 Specifications subject to change without notice. 40DAWE_1.5 series 40W - Single Output - Wide Input - Isolated & Regulated DC-DC Converter High efficiency up to 91% 2:1 wide input voltage range Isolation voltage 1500VDC Six-sided metal shield Short circuit protection (SCP) (automatic recovery) Operating temperature: -40°C to +85°C Over voltage protection Over current protection Industry standard pinout EN62368 approved DC-DC Converter 40 Watt The 40DAWE_1.5 series are isolated 40W DC-DC products with 2:1 input voltage. They feature efficiency up to 91%, 1500VDC isolation, operating temperature of -40°C to +85°C, output short circuit protection, over- voltage protection, over-current protection , which make them widely applied in data transmission device, battery power supply device, telecommunication device, distributed power supply system, remote control system, industrial robot fields. Example: 40DAWE_2415S1.5 40 = 40Watt; D = DIP; A = series; W = wide input (2:1); E = Eco series; 9-36Vin; 15Vout; S = single output; 1.5 = 1500VDC isolation Common specifications Cooling: Free air convection Short circuit protection: Hiccup, auto-recovery Operation temperature range: -40°C~+85°C Storage temperature range: -55°C~+125°C Vibration: 10-55Hz, 10G, 30 Min. along X, Y and Z Pin welding resistance temperature: 300°C MAX, 1.5mm from case for 10 sec Switching frequency (PWM mode)*: 300kHz TYP Humidity: non-condensing, 95% MAX Case material: Aluminum alloy Potting material: Epoxy (UL94V-0 rated) MTBF (MIL-HDBK-217F @25°C)*: 500,000 hours Weight: 26.8g (Typ.) - 36g with heatsink Dimensions: 50.80 × 25.40 × 11.80 mm 51.40 × 26.20 × 16.50 mm (heatsink) * This series of products using reduced frequency technology, the switching frequency is test value of full load. When the load is reduced to below 50%, the Note: 1. Input voltage can’t exceed this value, or will cause the permanent damage. 2. The load shouldn‘t be less than 5%, otherwise ripple will increase dramatically. 3. Max. Capacitive Load is tested on Vin-nominal and full load. 4. All specifications measured at Ta = 25°C, humidity <75%, nominal input voltage and rated output load unless otherwise specified. 5. In this datasheet, all the test methods of indications are based on corporate standards. 6. Only typical models listed, other models may be different, please contact our technical person for more details. 7. Specifications subject to change without notice. Isolation specifications Item Test condition Min Typ Max Units Isolation voltage Input/Output, tested for 1 minute and 1mA max

1500 VDC

Isolation resistance Test at 500VDC/60sec 1000 MΩ Isolation capacitance Input/Output, 100KHz/0.1V 2000 pF Output specifications Item Test condition Min Typ Max Units Voltage accuracy 0%-100% load ±1 ±3 % Line regulation input voltage from low to high @full load ±0.2 ±0.5 % Load regulation 0% to 100% load ±1 % Transient recovery time 25% load step change 300 500 µs Transient respon- se deviation 25% load step change ±3 ±5 % Temperature coefficient Full load ±0.03 %/°C Ripple and noise* 20MHz Bandwidth 50 100 mV Trim ±10 %Vo Over voltage protection Input voltage range 110 160 %Vo Over current protection Input voltage range 110 190 %Io * Test ripple and noise by “parallel cable” method. Input specifications Item Test condition Min Typ Max Units Input current (full load/no load)

  • 24Vin
  • 48Vin mA mA Reflected ripple current Nominal input voltage 30 mA Surge voltage (1s max.)
  • 24Vin
  • 48Vin -0.7 -0.7 100 VDC VDC Input under-voltage protection
  • 24Vin
  • 48Vin 15.5 VDC VDC Starting voltage • 24Vin
  • 48Vin VDC VDC Input filter Pi type Hot plug Unavailable Ctrl (The voltage of Ctrl pin is relative to input pin GND.)
  • Module ON
  • Module OFF
  • Input current when switched OFF Ctrl suspended or connected to TTL high level (3.5-12VDC) Ctrl pin connected to GND or low level (0-1.2VDC) 5 10 mA UL-62368-1 (E347551)

GAPTEC-Electronic GmbH & Co. KG sales@gaptec-electronic.com – www.gaptec-electronic.com Page 2 of 5 40DAWE_1.5 – Rev. 2020-1.2 Specifications subject to change without notice. 40DAWE_1.5 series 40W - Single Output - Wide Input - Isolated & Regulated DC-DC Converter Part Number Input Voltage Range [VDC] nominal Range Max. Output Voltage [VDC] Output Current [mA, max] Efficiency** [%, Typ.] Capacitive load [µF, max.] 40DAWE_2405S1.5 24 18-36 40 05 8000 88 10000 40DAWE_2412S1.5 24 18-36 40 12 3333 90 2700 40DAWE_2415S1.5 24 18-36 40 15 2667 91 1680 40DAWE_2424S1.5 24 18-36 40 24 1667 91 680 40DAWE_4812S1.5 48 36-75 80 12 3333 90 2700 40DAWE_4815S1.5 48 36-75 80 15 2667 91 1680 40DAWE_4824S1.5 48 36-75 80 24 1667 91 680 Add suffix “H” for heatsink mounted, for example: 40DAWE_2412SH1.5 Typical characteristics EMC specifications EMI CE CISPR32/EN55032 CLASS B (External Circuit Refer to EMC recommended circuit, ②) EMI RE CISPR32/EN55032 CLASS B (External Circuit Refer to EMC recommended circuit, ②) EMS ESD IEC/EN61000-4-2 Contact ±6KV perf. Criteria A EMS RS IEC/EN61000-4-3 10V/m perf. Criteria A EMS EFT IEC/EN61000-4-4 ±2KV perf. Criteria A (External Circuit Refer to recommended circuit, ①) EMS Surge IEC/EN61000-4-5 line to line ±2KV perf. Criteria A (External Circuit Refer to recommended circuit, ①) EMS CS IEC/EN61000-4-6 10 Vr.m.s perf. Criteria A 40DAWE_2405S1.5 40DAWE_2424S1.5 40DAWE_2424S1.5

GAPTEC-Electronic GmbH & Co. KG sales@gaptec-electronic.com – www.gaptec-electronic.com Page 3 of 5 40DAWE_1.5 – Rev. 2020-1.2 Specifications subject to change without notice. 40DAWE_1.5 series 40W - Single Output - Wide Input - Isolated & Regulated DC-DC Converter Efficiency Typical application and EMC solution recommended circuit 40DAWE_4812S1.5 40DAWE_4812S1.5

GAPTEC-Electronic GmbH & Co. KG sales@gaptec-electronic.com – www.gaptec-electronic.com Page 4 of 5 40DAWE_1.5 – Rev. 2020-1.2 Specifications subject to change without notice. 40DAWE_1.5 series 40W - Single Output - Wide Input - Isolated & Regulated DC-DC Converter Mechanical dimensions Application of Trim and calculation of trim resistance Note: Unit: mm[inch] General tolerances: ±0.5mm [±0.020inch] It is not allowed to connect modules output in parallel to enlarge the power.

GAPTEC-Electronic GmbH & Co. KG sales@gaptec-electronic.com – www.gaptec-electronic.com Page 5 of 5 40DAWE_1.5 – Rev. 2020-1.2 Specifications subject to change without notice. 40DAWE_1.5 series 40W - Single Output - Wide Input - Isolated & Regulated DC-DC Converter Mechanical dimensions