3755101 MALLORY | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 4
Technical content
UNILITE® DISTRIBUTOR This product is applicable to pre-1966 California and pre-1968 federally certified passenger cars. It is also applicable to non-emission controlled trucks and similar vehicles. It is not applicable or intended for use on any emission controlled vehicles operated on highways or roads, unless otherwise noted. INSTALLATION INSTRUCTIONS FORM 1214M (REV. K) 05/13 GENERAL INFORMATION Advance Curve: Most UNILITE® Distributors with part numbers that end in “01” have 24° (crankshaft degrees) of mechanical advance (between 3,000 and 3,200 RPM). Listed below are exceptions: Ignition Coils: The UNILITE ® Ignition system works with most stock ignition coils and aftermarket high performance ignition coils. For optimum performance, use a Mallory PROMASTER ® Coil Part No 29440 or 29625, or Mallory Chrome Electronic Ignition Coil Part No. 29216. Spark Plug Wires: To prevent false triggering and premature ignition failures, use suppression type spark plug wire. We recommend spiral core ignition wire, such as Mallory PRO SIDEWINDER ® Ignition Wire. Spark Plug Gaps: For street applications, use your engine manufacturer’s specifications. For racing applications, start with your engine manufacturer’s specifica- tions. Then experiment with, and closely monitor, various gaps to achieve maximum performance. Electric Welding: Disconnect the distributor wire harness before welding on the vehicle. NOTE: When replacing an HEI type distributor, it may be necessary to purchase and install distributor boots and terminals for the spark plug wires to correctly fit the UNILITE ® Distributor cap. Part No. 668 HEI to UNILITE® Boot Terminal Kit OLD DISTRIBUTOR REMOVAL Step 1 Disconnect the trigger wire from the coil (-) terminal. Locate the spark plug wire on the original distributor cap that that is used to set engine timing. See a service manual for this location. Mark the distributor cap and distributor housing at this spark plug wire position. Step 2 Turn the engine crankshaft in the direction of rotation until the timing mark lines up with the top dead center (TDC) mark on the timing tab. See a service manual for these locations. Step 3 Remove the distributor cap from the distributor. Do not remove the spark plug wires or coil wire at this time. Make sure the rotor blade points to the mark made on the distributor housing (from Step 2). If it does not, repeat Step 2 until the timing mark lines up (again) with the TDC mark on the timing tab. NOTE: Once you are finished with Step 3, DO NOT turn the crank- shaft until the new distributor is installed. Step 4 Note the direction that the rotor is pointing. If you are replacing a vacuum advance distributor, note the direction the vacuum chamber is pointing. Remove the distributor hold down clamp and remove the distributor from the engine. CAUTION: Leaving the key on without the engine running will result in damaging the Ignition Module and the coil. If you must have the key on unplug the distributor at the white connector first. UNILITE® DISTRIBUTOR INSTALLATION Step 1 Remove the distributor cap from the UNILITE ® Distributor. Step 2 Place the UNILITE ® Distributor in the engine. Rotate the UNILITE® Distributor housing in the opposite direction of rotor rotation until the nearest slot on the rotor’s shutter wheel is aligned with the optical eye of the UNILITE ® Module. This will generally give timing close enough for starting purposes. Put the distributor hold down clamp in place and tighten slightly, leaving it loose enough to turn the UNILITE® Distributor. Make a mark on the UNILITE® Distributor housing where the rotor points. Step 3 Install the UNILITE® Distributor cap. Remove the spark plug wire on the original distributor cap that the engine timing is set from, and install it onto the UNILITE ® Distributor cap post above the mark on the UNILITE® Distributor housing where the rotor had pointed. Install the remain- ing spark plug wires from the original distributor cap to the UNILITE Distributor cap in the same sequence. MALLORY IGNITION www.mallory-ignition.com 1 IMPORTANT Before installing the UNILITE® Distributor, make sure that your vehicle is equipped with an ignition ballast resistor (or loom resistance wire) in the wire between the ignition switch and the coil (+) terminal. Check a service manual for your vehicle to locate the ignition ballast resistor (or loom resistance wire). If your vehicle is not equipped with an ignition ballast resistor, install a Mallory Ignition Ballast Resistor Part No. 700 in the wire between the ignition switch and the coil (+) terminal. Failure to use an ignition ballast resistor will eventually destroy the UNILITE ® Ignition Module. PARTS INCLUDED IN THIS KIT: 1 UNILITE ® Distributor 1 Distributor Wire Harness
The 3 wires coming from the UNILITE® Distributor must be con- nected using the distributor wire harness furnished (see Figures 1 and 2). RED WIRE: If you use loom resistance wire, connect to the coil (+) terminal. If you use a ballast resistor, connect to 12 volt side of ballast resistor. GREEN WIRE: Connect to the coil (–) terminal. BROWN WIRE: Connect to engine block ground. Clean away any grease, oil and paint from the mounting surface before the connection is made. ADDITIONAL CONNECTIONS Vacuum advance applications: Connect original vacuum hose to the UNILITE ® Distributor vacuum chamber. Replace hose if cracked, dam- aged, or if it is not long enough. If the previous distributor was not equipped with vacuum advance, connect a vacuum hose to a ported vacuum outlet on the carburetor. Tachometer operation: Connect wire or wires as recommended by the actual tachometer manufacturer. STARTING ENGINE CAUTION: Be sure all tools, wires and miscellaneous objects are clear of moving engine parts and extreme heat before staring the engine. Step 1 Recheck all wires and connections to make sure they are correct. Check and clean, or replace spark plugs. If replacing spark plugs, use types recommended by the engine manufacturer. Vacuum advance applications: Disconnect the vacuum hose to UNILITE Distributor vacuum chamber at the carburetor and temporarily plug this carburetor fitting. Step 2 Connect a timing light and start the engine. If the engine fails to start, rotate the distributor in small increments clockwise or counterclockwise until the engine starts. Do not exceed more than ten degrees of distributor housing rotation in either direction. Step 3 Set timing as recommended by the engine manufacturer, then tighten distributor hold down clamp. Check timing again. If timing has moved, repeat Step 3. Vacuum advance applications: Reconnect the vacuum hose between the UNILITE ® Distributor vacuum chamber and the carburetor. 2 www.mallory-ignition.com MALLORY IGNITION COIL UNILITE® WIRING DIAGRAM USING BALLAST RESISTORFIGURE 1 NOTE: The purpose of an ignition ballast resistor between the ignition switch (12V) and the ignition coil positive terminal is to restrict current flow through the ignition coil. Failure to use an ignition ballast resistor will eventually destroy the Ignition Module. EXCEPTION: If your vehicle is equipped with a HYFIRE ® Electronic Ignition Control or similar aftermarket ignition control, use the wiring procedures stated in the instructions included with the ignition control. To prevent false triggering and possible premature ignition failure, you must use suppression type (carbon core, spiral core, or radio suppression core) spark plug wire. DO NOT USE SOLID CORE (COPPER CORE OR STAINLESS STEEL CORE) SPARK PLUG WIRE WITH ANY ELECTRONIC IGNITION SYSTEM. IGNITION MODULE FEMALE CONNECTOR ENGINE GROUND DISTRIBUTOR WIRE HARNESS PART NO. 29349 IGNITION BALLAST RESISTOR BROWN GREEN RED ALL OTHER WIRES ORIGINALLY CONNECTED TO THE COIL (+) TERMINAL 12V/IGNITION SWITCH
UNILITE® WIRING DIAGRAM USING OEM PRIMARY RESISTANCE WIREFIGURE 2 NOTE: The purpose of resistance wire between the ignition switch (12V) and the ignition coil positive terminal is to restrict current flow through the ignition coil. Failure to use resistance wire will eventually destroy the Ignition Module. EXCEPTION: If your vehicle is equipped with a HYFIRE ® Electronic Ignition Control or similar aftermarket ignition control, use the wiring procedures stated in the instructions included with your ignition control. To prevent false triggering and possible premature ignition failure, you must use suppression type (carbon core, spiral core, or radio suppression core) spark plug wire. DO NOT USE SOLID CORE (COPPER CORE OR STAINLESS STEEL CORE) SPARK PLUG WIRE WITH ANY ELECTRONIC IGNITION SYSTEM. NOTE: The Red wire from the distributor would prefer to see 12v using a loom resistor makes that a little more difficult. IGNITION MODULE FEMALE CONNECTOR ENGINE GROUND 12V/IGNITION SWITCH DISTRIBUTOR WIRE HARNESS PART NO. 29349 LOOM RESISTANCE WIRE BROWN GREEN RED ALL OTHER WIRES ORIGINALLY CONNECTED TO THE COIL (+) TERMINAL COIL MALLORY IGNITION CONTROL OR TIMING ACCESSORY ENGINE GROUND IGNITION CONTROL PLUG IGNITION CONTROL HARNESS SMALL GREEN AND BLACK MAGNETIC PICKUP WIRES NOT USED REFER TO IGNITION CONTROL INSTRUCTIONS FOR REMAINING POWER CONNECTIONS PART NOS. 600, 610, 629, 630, 631, 685, 692, OR 697 DISTRIBUTOR WIRE HARNESS PART NO. 29349 12V/IGNITION SWITCH IGNITION BALLAST RESISTOR RING TERMINAL CONNECTORS PART NO. 450 IGNITION MODULE FEMALE CONNECTOR GREEN BLACK BROWN GREEN YELLOW RED RED ALL WIRES NORMALLY CONNECTED TO THE COIL (+) TERMINAL To prevent false triggering and possible premature ignition failure, you must use suppression type (carbon core, spiral core, or radio suppression core) spark plug wire. DO NOT USE SOLID CORE (COPPER CORE OR STAINLESS STEEL CORE) SPARK PLUG WIRE WITH ANY ELECTRONIC IGNITION SYSTEM. Installing an ignition ballast resistor has no effect on the performance of the ignition system. However, installing or retaining the original ignition ballast resistor allows for easy conversion back to standard ignition. FIGURE 3 WIRING DIAGRAMS USING AFTERMARKET ELECTRONIC IGNITION CONTROLS 3MALLORY IGNITION www.mallory-ignition.com
AUTOMOTIVE AND MARINE UNILITE® DISTRIBUTOR TUNE–UP PARTS ROTOR/SHUTTER ROTOR/SHUTTER AUTOMOTIVE DISTRIBUTOR CAP (EXCEPT 47 SERIES) 47 SERIES ONLY 8 CYL. (STACK CAP) 209 335 322 8 CYL. (FLAT CAP) 221 360 – 6 CYL. (37 AND 38 SERIES) 226 331 – 6 CYL. (45, 46 AND 47 SERIES) 270 339 323 4 CYL. (37 AND 38 SERIES) 225 337 – 4 CYL. (45, 46 AND 47 SERIES) 271 340 325 MARINE (YLU SERIES ONLY) 8 CYL. (STACK CAP) 209D 335 8 CYL. (FLAT CAP) 221B 360 6 CYL. (SMALL HOUSING, 3.12” O.D.) 226B 331 6 CYL. (LARGE HOUSING, 3.65” O.D.) 270B 339 4 CYL. (SMALL HOUSING, 3.12” O.D.) 225B 337 4 CYL. (LARGE HOUSING, 3.65” O.D.) 271B 340 UNILITE® MODULE, ALL MODELS: PART NO. 605 DISTRIBUTOR WIRE HARNESS, ALL MODELS: PART NO. 29349 OPTIONAL ACCESSORIES FOR THE UNILITE® DISTRIBUTOR Helps prevent module failures due to voltage spikes associated with “noisy” electrical systems and electrical defects. Required to change the amount and rate of advance within a range of 14° to 28°. Includes degree keys, springs, and instructions to plot advance curves. COIL MSD™ 6 SERIES IGNITION PART NO. 6200, 6400, 6420 or 6462 ENGINE GROUND MAGNETIC PICKUP CONNECTOR NOT USED REFER TO MSD™ INSTRUCTIONS FOR REMAINING POWER CONNECTIONS DISTRIBUTOR WIRE HARNESS PART NO. 29349 12V/IGNITION SWITCH IGNITION BALLAST RESISTOR RING TERMINAL CONNECTORS PART NO. 450 IGNITION MODULE FEMALE CONNECTOR WHITE BLACK BROWN GREEN ORANGE RED RED ALL WIRES NORMALLY CONNECTED TO THE COIL (+) TERMINAL To prevent false triggering and possible premature ignition failure, you must use suppression type (carbon core, spiral core, or radio suppression core) spark plug wire. DO NOT USE SOLID CORE (COPPER CORE OR STAINLESS STEEL CORE) SPARK PLUG WIRE WITH ANY ELECTRONIC IGNITION SYSTEM. Installing an ignition ballast resistor has no effect on the performance of the ignition system. However, installing or retaining the original ignition ballast resistor allows for easy conversion back to standard ignition. MALLORY 6A, 6AL and MSDTM 6 SERIES IGNITION PART NO. 6200, 6400, 6420 or 6462 4 www.mallory-ignition.com MALLORY IS A TRADEMARK OF PRESTOLITE PERFORMANCE 10601 MEMPHIS AVE. #12, CLEVELAND, OH 44144 216.688.8300 FAX 216.688.8306 family of brands FORM 1214M (REV. K) 05/13