DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 3

Technical content

[EER NIX CONTACT Mini Spring-Cage Terminal Block MZB Article description MZDB 1,5* Zi Article no. 3003800 * a a EC-TYPE EXAMINATION CERTIFICATE KEMA 98ATEX0545 U * ie 2 Marking Exell ts = KEMA 98ATEX0545 U ie Assembly on mounting rails NS 15 acc. to EN 60715-TH 15 yi i Stripping length 9mm . L Assembly instructions See page2 ~ Operating temperature range -50 °C ... +110 °C &) Technical data according to IEC/EN 60079-7 (increased Safety ,,e“) Rated insulation voltage 630 V Rated voltage 690 V Nominal current 17,5A Max. rated current 244 Contact resistance 0,6 mQ Temperature rise 25K Connection capacity Rated cross-section 1,5 mm? AWG 16 Max. conductor cross-section 2,5 mm? AWG 14 " 0,14 - 2,5 mm? rigid AWG 26 - 14 Connectable conductor cross-section 0.14- 1.5 mm? flexible AWG 26 - 16 Data of insulation material Description PA6.6 Creep resistance acc. to IEC 60112 / material group CTI 600/1 Accessories Description Article no. Cover D-MZB 1,5 3024177 * valid for colour variants 2012-10-29 PHOENIX CONTACT GmbH & Co. KG Page 1 of 3 Rev. 03.1 Flachsmarktstrae 8 Technical modifications reserved 32825 Blomberg

Important assembly instructions — increased Safety ,,e“ The Terminal Blocks are suitable for use in enclosures in atmospheres with flammable gases or combustible dust. For flammable gases these enclosures must satisfy the requirements according to IEC/EN 60079-0 and IEC/EN 60079-7. For combustible dust these enclosures must satisfy the relevant requirements according to IEC/EN 60079-31. When assembling with other certified series and sizes of terminal blocks and using belonging accessories, the required creepage distances and clearances have to be observed. If conductors with smaller cross section as the rated cross section are used, the belonging lower current has to be laid down in the EC-Type Examination Certificate of the complete apparatus. The Terminal Blocks may be used, based on the self-heating when used at the nominal current and at ambient temperatures of -50 °C to +40 °C at the mounting position in electrical apparatus, e.g. junction and connection boxes, for temperature class T6. When the Terminal Blocks are used in electrical apparatus of temperature classes T1 up to TS, the highest temperature of the insulating material shall not exceed the maximum value of the operating temperature range. The Terminal Blocks and their appropriate accessories have to be assembled as. specified below. Terminal block Terminal block End holder Terminal block Terminal block MZB 1,5-M MZDB 1,5-M E/MK4i MZB 15 MZDB 1,5 MZB 1,5-RZ MZDB 1.5-RZ Cover NS 15 acc. to / cael EN 60715-TH 15 ] L nd SAS) SSS eetistheoe fa | a a td hd eae AAR AAA aa SS SmaSrSl Se asi eli — cS FI AAR lala ial al FAA a = ee 2012-10-29 Page 2 of 3 2012-104 [a PHenix Technical modifications reserved CONTACT

Operational instructions — Intrinsic safety “i* IEC/EN 60079-14 Clause 12 describes modular terminal blocks as simple apparatus when used in intrinsically-safe circuits. Testing by a notified body and marking is not required. If terminal blocks be identifiable as part of an intrinsically circuit are marked by a colour, the colour used shall be light blue. Testing for compliance to intrinsically safe requirements including clearance, creepage, and solid insulation distances specified in IEC/EN 60079-0 and IEC/EN 60079-11 have been performed for circuits up to 60 V. Compliance with distance requirements of IEC/EN 60079-14 Clause 12.2.3 for the connection of separated intrinsically-safe circuit accessories is met. A minimum distance of 50 mm to separate clamping units of intrinsically-safe and non intrinsically-safe circuits is required through the use of a separating plate or similar device. Attestation of Conformity The above mentioned product is in line with the provisions of the below marked directive and their modification directive(s): 94/9/EC ATEX Directive Compliance with Essential Health and Safety Requirements has been assured by compliance with: EN 60079-0:2006 EN 60079-7:2007 EN 50281-1-1:1998 + A1 IEC 60079-0:2004 JEC 60079-7:2006 current eddition:” EN 60079-0:2009 EN 60079-7:2007 IEC 60079-0:2011 IEC 60079-7:2006 The conformity with the provisions of the ATEX directive were certified by Notified Body: KEMA Quality B.V. Adress: Utrechtseweg 310, NL-6812 AR Arnhem, The Netherlands [Ident.-No.: 0344] Certificate: e-bay KEMA 98ATEX0545 U, 2007-10-18 With the exception of the EPL marking, the minor respectively formal changes of the new edition of the mentioned standards do not affect the EHSRs. Consequently the terminal blocks still comply with the = relevant requirements of the ATEX Directive 94/9/EC. A Blomberg, 2012-10-29 Zorn LIVI Fon a J Ji & Gerhard Le&mann “Dirk Gérlitzer Business Unit Industrial Connection Business Unit Industrial Connection Technology Technology Ex-Representative Head of Business Unit This attestation certifies the conformity with the indicated directive, it does not, however, covenant any characteristics. The instructions for safety and installation have to be observed. PHOENIX CONTACT GmbH & Co. KG FlachsmarktstraRe 8

32825 Blomberg

sy www.phoenixcontact.com Ne ee eS 2012-10-29 PHOENIX CONTACT GmbH & Co. KG Page 3 of 3 Rev. 03.1 FlachsmarktstraBe 8 Technical modifications reserved 32825 Blomberg