200ACP GAPTEC | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 3

Technical content

GAPTEC-Electronic GmbH & Co. KG sales@gaptec-electronic.com – www.gaptec-electronic.com Page 1 of 3 200ACP_SC – Rev. 2020-1.1 Specifications subject to change without notice. 200ACP_SC series 200W - Single Output AC-DC Converter - Universal Input - Isolated & Regulated High efficiency up to 88.5% Universal AC input range (85~264VAC) Built-in Active PFC function, PF>0.95 Over power protection (OPP) Over load protection (OLP) Short circuit protection (SCP) Wide operating ambient temperature (-20°C~70°C) Operating altitude up to 5000M 100% full load burn-in test Easy assembling from top side PCB soldering side with conformal coating AC-DC Converter 200 Watt The 200ACP_SC series features standard rail mounting, energy efficien- cy and is highly cost-effective. The series offers stability and high noise immunity especially for industrial control equipment, machinery and other demanding environments for industri al equipment. This conver - ter offers a compact and light weight design with and standard rail installation (35mm). Furthermore this series offers Easy Fuse Tripping due and a built-in DC OK relay contact. The converter can be installed on TS-35/7.5 or TS-35/15. Example: 200ACP_24SC 200 = 200Watt ; AC = AC-DC ; P = series ; 24 = 24 Vout; S = single output; C = PFC (Power Factor Correction) Input specifications Input voltage range 90~264VAC Input frequency 47~63Hz Power factor 115VAC

  • 0.98 (typ) 230VAC
  • 0.95 (typ) AC current 3A (max) Inrush current Cold start 115VAC
  • 30A (typ) 230VAC
  • 50A (typ) Leakage current Input—output: ≤0.25mA Input—PG: ≤3.5mA Output specifications Item Test conditions Min Typ Max Units Output voltage accuracy Full load
  • 12V
  • 24V/48V Voltage adjustment range
  • 12V
  • 24V
  • 48V 15.5 27.2 V V V Line regulation Vin= min. to max. at full load ±0.5 % Load regulation 0% to 100% load
  • 12V
  • 24V/48V Set-up time • @230VAC input
  • @115VAC input s s Hold-up time @full load 16 ms Overshoot and undershoot 5 % Switching fre- quency

100 KHz

  • Measured at 20MHz of bandwidth by using a 12” twisted pair-wire terminated with a 0.1 uF & 10uF parallel capacitor. Protection specifications Over-load protection 105%~150% of rated output current, hiccup mode, auto recovery Over-power protection 105%~150% of rated output current, hiccup mode, auto recovery Common specifications Short circut protection: Long-term mode, automatic recovery Temperature rise at full load: 40°C MAX Cooling: Free air convection Operation temperature range: -20°C~+65°C Storage temperature range: -40°C ~+85°C Storage humidity range: < 95% Temperature coefficient: 0.03%/°C MAX MTBF (using MIL-HDBK-217F): +25°C >200,000 hours Power boost: 150% of rated current Parallel function: support Safety standards: UL60950-1 2nd Ed; IEC 60950-1:2005 (2nd Ed); EN60950-1:2006 Case material: Heat-resistant Plastic (UL94-V0) and metal Dimensions: 199*99*38mm Weight: 800g UL-60950-1 (E347551) Isolation specifications Item Test condition Min Typ Max Units Withstand voltage* • Primary-Sec.: 10mA
  • Primary-PG: 10mA
  • Secondary-PG: 10mA 3000 1500 500 VAC Isolation resistance 100 MΩ * Input-Output, tested for 1 minute, 500VDC and leakage current less than 1mA Note: 1. All parameters NOT specially mentioned are measured at rated input, rated load and 25°C of ambient temperature.

GAPTEC-Electronic GmbH & Co. KG sales@gaptec-electronic.com – www.gaptec-electronic.com Page 2 of 3 200ACP_SC – Rev. 2020-1.1 Specifications subject to change without notice. 200W - Single Output AC-DC Converter - Universal Input - Isolated & Regulated 200ACP_SC Series Mechanical dimensions 1-4 M3 2.5mm 6.5kgf.cm (max) 5-6 M3 4mm 6.5kgf.cm (max) 7-12 M3 4mm 6.5kgf.cm (max) 13-14 M4 4mm 12kgf.cm (max) EMC specifications EMC / Emission Compliance to EN55022, EN55024, FCC PART 15 Class B EMC / Harmonic current Compliance to EN61000-3-2, CLASS D EMC / Immunity Compliance to EN61000-4-2, -3, -4, -5, -6, -8, -11; heavy industry level The power supply is considered as a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. Approval Model Power [W] Output [Vo, VDC] Rated Current [A] Current Range [A] Ripple&Noise* [mV, typ] 0~65°C -20~0°C Efficiency [%, typ] UL 200ACP_12SC 200 12 16.7 0~16.7 150 200 87 UL 200ACP_24SC 200 24 8.4 0~8.4 200 200 88 UL 200ACP_48SC 200 48 4.2 0~4.2 150 150 88.5 Measured at 20MHz of bandwidth by using a 12” twisted pair-wire terminated with a 0.1 uF & 10uF parallel capacitor.

GAPTEC-Electronic GmbH & Co. KG sales@gaptec-electronic.com – www.gaptec-electronic.com Page 3 of 3 200ACP_SC – Rev. 2020-1.1 Specifications subject to change without notice. 200W - Single Output AC-DC Converter - Universal Input - Isolated & Regulated 200ACP_SC Series Typical characteristics Functional block diagram Derating Curve Efficiency AMBIENT TEMPERATURE (°C) INPUT VOLTAGE (VAC) LOAD (%) LOAD (%) Functional diagram