18KBXC-Y3

18KBXC MSYSTEM | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 6

Technical content

MODEL: 18KBXC http://www.m-system.co.jp/ 18KBXC SPECIFICATIONS ES-0492 Rev.0 Page 1/6 Rack-mounted DCS Signal Conditioners 18K-RACK STANDARD RACK Functions & Features

• Standard 19" rack for 18K-RACK signal conditioners
• 18-Rack signal conditioners are also mountable
• Module can be retracted without removing wiring for an insulation test
• Line power supplied via the rear rack bus
• Direct interface to various DCS with the rack side connector MODEL: 18KBXC–[1][2]

ORDERING INFORMATION

• Code number: 18KBXC-[1][2] Specify a code from below for each [1] and [2]. (e.g. 18KBXC-Y1/W) [1] CONNECTOR 0: None U1: Fujitsu FCN type I/O connector Y1: Yokogawa DCS MAC2 / PAC card use Y2: Yokogawa DCS VMx / PM1 card use Y3: Yokogawa DCS for Module
• AAB841 (Adapter: ATV4A, Cable: KS2) E4: Toshiba DCS VTBU card use K1: Yamatake DCS AI connector K2: Yamatake DCS AO connector K5: Yamatake DCS PI connector M-System guarantees the connecting section. [2] OPTIONS Mounting Bracket blank: Rack mounting, standard /W: Surface mounting

RELATED PRODUCTS

• Blank filler plate (model: P-181)
• Connector terminal block (model: CNT)
• Special cable with 40-pin connector (model: FCN) GENERAL SPECIFICATIONS Construction: Metal plates assembly Coating: Colored Zn-Cr Capacity: 16 positions Connection Power input: M4 screw terminals (torque 0.8 N·m) Field terminal: M3.5 screw terminals (torque 0.8 N·m) Screw terminal Power: Nickel-plated brass Field terminal: Nickel-plated steel Isolation: I/O connector to field terminal to power to FG INSTALLATION Power input
• DC: Operating voltage range 24 V DC ±10 %, 2.5 A minimum (ripple 10 % p-p max.) Operating temperature: -5 to +55°C (23 to 131°F) Operating humidity: 30 to 90 %RH (non-condensing) Mounting: JIS or EIA standard rack or surface Weight: 2.7 kg (5.95 lb) PERFORMANCE Insulation resistance: ≥ 100 MΩ with 500 V DC Dielectric strength: 500 V AC @ 1 minute (I/O connector to field terminal to power)

1000 V AC @ 1 minute (I/O connector or field terminal or

power to FG)

MODEL: 18KBXC http://www.m-system.co.jp/ 18KBXC SPECIFICATIONS ES-0492 Rev.0 Page 2/6 MOUNTING REQUIREMENTS unit: mm (inch) 101.6 (4.00) * 450 (17.72) 465 (18.31) 4–M5 SCREW ANGLE BRACKET Observe an appropriate wiring space over and below. 100 (3.94) for JIS standard CONNECTION DIAGRAM FG 3 CN1 CN2 POWER Note 1: CN1 and CN2 are not available without connector. Note 2: CN2 is only available with

• Fujitsu FCN type I/O connector
• Y okogawa DCS MAC2 / PAC card use
• Y okogawa DCS for Module / AAB841 (Adapter: ATV4A, Cable: KS2)
• Y amatake DCS PI connector ɹɹ ɹɹ FIELD TERMINALS

MODEL: 18KBXC http://www.m-system.co.jp/ 18KBXC SPECIFICATIONS ES-0492 Rev.0 Page 3/6 DIMENSIONS unit: mm (inch) 1 3 15 2 14 16 15 14 16 2 (.08) 435 (17.13) 134 (5.28) 2 (.08) ■ RACK (standard) ■ SURFACE (option /W) 465 (18.31) 480 (18.90) CN2 CONNECTORCN1 1 3 5 7 9 11 13 15 2 4 6 8 10 12 14 16 150 (5.91) 101.6 (4.00) 8.5 (.33) 3-M4 POWER TERMINAL 8.2 (.32) 64−M3.5 FIELD TERMINAL* 1 2 1 2 1 2 3 4 3 4 3 4 1ch 15ch 16ch *Field I/O Terminal Block

MODEL: 18KBXC http://www.m-system.co.jp/ 18KBXC SPECIFICATIONS ES-0492 Rev.0 Page 4/6 I/O CONNECTOR PIN ASSIGNMENT Fujitsu FCN type I/O connector (Fujitsu FCN-365P040-AU) Connector Pin Assignment CN1: output 1 or input CN2: output 2 PIN NO. ASSIGNMENT PIN NO. ASSIGNMENT A 1 ch. 1 + B 1 ch. 1 – A 2 ch. 2 + B 2 ch. 2 – A 3 ch. 3 + B 3 ch. 3 – A 4 ch. 4 + B 4 ch. 4 – A 5 ch. 5 + B 5 ch. 5 – A 6 ch. 6 + B 6 ch. 6 – A 7 ch. 7 + B 7 ch. 7 – A 8 ch. 8 + B 8 ch. 8 – A 9 ch. 9 + B 9 ch. 9 – A10 ch.10 + B10 ch.10 – A11 ch.11 + B11 ch.11 – A12 ch.12 + B12 ch.12 – A13 ch.13 + B13 ch.13 – A14 ch.14 + B14 ch.14 – A15 ch.15 + B15 ch.15 – A16 ch.16 + B16 ch.16 – A17 – A20, B17 – B20: Unused Pin assignment is common to both CN1 and CN2. Yokogawa DCS MAC2 / PAC card use (PS-40PE-D4LT1-PN1) Location CN1: MAC2 / PAC card use* CN2: MAC2 / PAC card use* (for redundancy) The input or output 1 is connected to the connector. 18K-RACK LOCATION NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 i o i o i o i o i o i o i o i o MAC2/PAC CARD I/O (i = input, o = output) *MAC2 card (uses KS1 cable) I/O card used for control I/O. Composed of 8 inputs and 8 outputs. Input and output are paired. (Replace with pulse inputs for PAC card.) Yokogawa DCS VMx / PM1 card use (PS-40PE-D4LT1-PN1) Location CN1: VMx / PM1 card use* The input or output 1 is connected to the connector. 18K-RACK LOCATION NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 VM1/PM1/VM4 CARD INPUT or OUTPUT 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 VM2 CARD INPUT NO. VM2 CARD OUTPUT NO. *VMx / PM1 card (uses KS2 cable) VM1: analog input 16 points VM2: analog input 8 points / analog output 8 points VM4: analog output 16 points PM1: pulse input 16 points Connector Pin Assignment (CN1, CN2) PIN NO. ASSIGNMENT PIN NO. ASSIGNMENT 40 ch. 1 + 24 ch. 9 + 39 ch. 1 – 23 ch. 9 – 38 ch. 2 + 22 ch.10 + 37 ch. 2 – 21 ch.10 – 36 ch. 3 + 20 ch.11 + 35 ch. 3 – 19 ch.11 – 34 ch. 4 + 18 ch.12 + 33 ch. 4 – 17 ch.12 – 32 ch. 5 + 16 ch.13 + 31 ch. 5 – 15 ch.13 – 30 ch. 6 + 14 ch.14 + 29 ch. 6 – 13 ch.14 – 28 ch. 7 + 12 ch.15 + 27 ch. 7 – 11 ch.15 – 26 ch. 8 + 10 ch.16 + 25 ch. 8 – 9 ch.16 – Yokogawa DCS for Module AAB841 module (Adapter: ATV4A, Cable: KS2)* Location CN1: Single CN2: Unused* * The input or output 1 is connected to the connector. 18K-RACK LOCATION NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 AAB841 module INPUT NO. The CN1 and CN2 are connected in parallel. 1 – 8: Unused *I/O module AAB841: Analog I/O module (1 - 5 V input, 4 - 20 mA output, input 8 points / output 8 points, non-isolated) **Not available for redundancy (PS-40PE-D4LT1-PN1) AAB841 module OUTPUT NO. PIN NO. ASSIGNMENT PIN NO. ASSIGNMENT 1 ch. 1 + 19 ch. 1 – 2 ch. 2 + 20 ch. 2 – 3 ch. 3 + 21 ch. 3 – 4 ch. 4 + 22 ch. 4 – 5 ch. 5 + 23 ch. 5 – 6 ch. 6 + 24 ch. 6 – 7 ch. 7 + 25 ch. 7 – 8 ch. 8 + 26 ch. 8 – 9 ch. 9 + 27 ch. 9 – 10 ch.10 + 28 ch.10 – 11 ch.11 + 29 ch.11 – 12 ch.12 + 30 ch.12 – 13 ch.13 + 31 ch.13 – 14 ch.14 + 32 ch.14 – 15 ch.15 + 33 ch.15 – 16 ch.16 + 34 ch.16 – Toshiba DCS VTBU card use (57LE-40360-7700) • Connector Pin Assignment CN1: VTBU card use The output 1 is connected to the connector. 17, 18, 35 and 36: Unused

MODEL: 18KBXC http://www.m-system.co.jp/ 18KBXC SPECIFICATIONS ES-0492 Rev.0 Page 5/6 Yamatake DCS AI connector • Location Input connector : 57LE-40500-7300 CN1: AI use 18K-RACK LOCATION NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 YAMATAKE DCS AI CARD (J-HAM50/HMM00) INPUT Yamatake DCS AO connector • Location Output connector : 57LE-40500-7300 CN1: AO use 18K-RACK LOCATION NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 YAMATAKE DCS AO CARD (J-AOM10) OUTPUT Connector Pin Assignment (CN1) PIN NO. ASSIGNMENT PIN NO. ASSIGNMENT 3 ch. 1 + 11 ch. 9 + 4 ch. 1 – 12 ch. 9 – 5 ch. 2 + 13 ch.10 + 6 ch. 2 – 14 ch.10 – 7 ch. 3 + 15 ch.11 + 8 ch. 3 – 16 ch.11 – 9 ch. 4 + 17 ch.12 + 10 ch. 4 – 18 ch.12 – 27 ch. 5 + 19 ch.13 + 26 ch. 5 – 20 ch.13 – 29 ch. 6 + 21 ch.14 + 28 ch. 6 – 22 ch.14 – 31 ch. 7 + 23 ch.15 + 30 ch. 7 – 24 ch.15 – 33 ch. 8 + 25 ch.16 + 32 ch. 8 – 50 ch.16 – 34 – 37 (CN1): Unused 1 and 2, 48 and 49 in CN1 are connected. The input is connected to the connector. Yamatake DCS PI connector • Location Output connector : 57LE-40500-7300 CN1, CN2: PI use 18K-RACK LOCATION NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 YAMATAKE DCS PI CARD (J-PIM00) INPUT Connector Pin Assignment (CN1 , CN2) PIN NO. ASSIGNMENT PIN NO. ASSIGNMENT 3 ch. 1 + 3 ch. 9 + 4 ch. 1 – 4 ch. 9 – 5 ch. 2 + 5 ch.10 + 6 ch. 2 – 6 ch.10 – 7 ch. 3 + 7 ch.11 + 8 ch. 3 – 8 ch.11 – 9 ch. 4 + 9 ch.12 + 10 ch. 4 – 10 ch.12 – 27 ch. 5 + 27 ch.13 + 26 ch. 5 – 26 ch.13 – 29 ch. 6 + 29 ch.14 + 28 ch. 6 – 28 ch.14 – 31 ch. 7 + 31 ch.15 + 30 ch. 7 – 30 ch.15 – 33 ch. 8 + 33 ch.16 + 32 ch. 8 – 32 ch.16 – 11 – 25 and 50 (CN1, CN2): Unused 1, 36, 38, 39, 41, 42, 43 and 45 in CN1 and CN2 are connected. The output 1 is connected to the connector. YAMATAKE DCS PI CARD (J-PIM00) INPUT CN1 CN2 2, 34, 35, 37, 40, 44, 46 and 47 in CN1 and CN2 are connected. 48 and 49 in CN1 and CN2 are connected. (CN1) (CN2)

MODEL: 18KBXC http://www.m-system.co.jp/ 18KBXC SPECIFICATIONS ES-0492 Rev.0 Page 6/6 Specifications are subject to change without notice.