1437737 PHOENIX | Alldatasheet

Document overview

  • Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
  • PDF pages: 14

Technical content

Please be informed that the data shown in this PDF document is generated from our online catalog. Please find the complete data in the user documentation. Our general terms of use for downloads are valid. Bus system flush-type plug, Ethernet, 4-pos., M12 SPEEDCON, shielded, D-coded, rear/screw mounting with Pg9 thread, with 1.0 m bus cable, 2 x 2 x 0.2 mm2 Your advantages Preassembled with cables in various standard lengths for immediate use• Customer-specific assemblies and cable lengths can be supplied Sealed on the cable side for optimum tightness of seal Cable designs for all common networks and fieldbuses For high transmission safety: shield connection to the housing with optional EMC nut Commercial data Item number 1437737 Packing unit 1 pc Minimum order quantity 1 pc Product key ABQDGD GTIN 4046356458474 Weight per piece (including packing) 71.6 g Weight per piece (excluding packing) 71.6 g Country of origin DE SACCBP-MSD-4CON-PG9/1,0-931SCO - Device connector, rear mounting 1437737 https://www.phoenixcontact.com/us/products/1437737 Oct 6, 2023, 5:57 AM Page 1 (14)

General The electrical and mechanical data specified assume that the connector pair is correctly locked and mounted. If the connector is unlocked and if there is a danger of contamination, the connector must be sealed using a protective cap > IP54. Influences arising from litz wires, cables or PCB assembly must also be taken into consideration. Safety note WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.

  • WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
  • WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
  • The products are suitable for applications in plant, controller, and electrical device engineering.
  • When operating the connectors in outdoor applications, they must be separately protected against environmental influences.
  • Assembled products may not be manipulated or improperly opened.
  • Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products).
  • When using the product in direct connection with third-party manufacturers, the user is responsible.
  • For operating voltages > 50 V AC, conductive connector housings must be grounded
  • Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
  • Observe the corresponding technical data. You will find information: o On the product o On the packing label o In the supplied documentation o Online at phoenixcontact.com/products under the product
  • Only use tools recommended by Phoenix Contact
  • Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products Safety note SACCBP-MSD-4CON-PG9/1,0-931SCO - Device connector, rear mounting 1437737 https://www.phoenixcontact.com/us/products/1437737 Oct 6, 2023, 5:57 AM Page 2 (14)
  • Ensure that the protective or functional ground has been properly connected. are applicable when combining several circuits in a cable and/or connector
  • The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12). Mounting Mounting type Rear mounting Product properties Product type Circular connectors (device side) Sensor type Ethernet Number of positions 4 No. of cable outlets 1 Coding D Thread type M12 Insulation characteristics Overvoltage category II Degree of pollution 3 Material specifications Flammability rating according to UL 94 V0 Seal material FKM Contact material CuZn Contact surface material Ni/Au Contact carrier material PA 6.6 Electrical properties Rated surge voltage 2.5 kV

48 V ACNominal voltage UN

60 V DC

Nominal current IN 1.5 A (Plug/socket in accordance with IEC 61076-2-101, cable technical data is to be observed) Transmission medium Copper Transmission characteristics (category) CAT5 (IEC 11801:2002) Mechanical properties Mechanical data Insertion/withdrawal cycles ≥ 100 SACCBP-MSD-4CON-PG9/1,0-931SCO - Device connector, rear mounting 1437737 https://www.phoenixcontact.com/us/products/1437737 Oct 6, 2023, 5:57 AM Page 3 (14)

Head cable outlet straight Head thread type M12 Head locking type SPEEDCON Coding D Connection 2 Head design free cable end Cable/line Ethernet flexible CAT5, 2-pair [93E] Dimensional drawing Cable weight 42 kg/km UL AWM Style 20963 (80°C/30 V) Wiring standards/regulations Electrical requirements EN 50288-2-2 Number of positions 4 Shielded yes Cable type Ethernet flexible CAT5, 2-pair [93E] Conductor structure 2x2xAWG26/7, SF/UTP Signal runtime 5.3 ns/m Conductor structure signal line 7x 0.16 mm AWG signal line 26 Conductor cross section 2x 2x 0.14 mm² Wire diameter incl. insulation 0.98 mm External cable diameter 6.4 mm ±0.2 mm Outer sheath, material PUR External sheath, color water blue RAL 5021 Conductor material Bare Cu litz wires Material wire insulation Foamed PE Single wire, color white/orange-orange, white/green-green Thickness, outer sheath 1.2 mm Twisted pairs 2 cores to the pair SACCBP-MSD-4CON-PG9/1,0-931SCO - Device connector, rear mounting 1437737 https://www.phoenixcontact.com/us/products/1437737 Oct 6, 2023, 5:57 AM Page 4 (14)

Overall twist Two pairs with two fillers to the core Optical shield covering 70 % Insulation resistance ≥ 500 MΩ*km Coupling resistance ≤ 100.00 mΩ/m (at 10 MHz) Loop resistance ≤ 290.00 Ω/km Wave impedance 100 Ω ±5 Ω (at 100 MHz) Cable capacity approx. 45 nF/km (at 1 kHz) Nominal voltage, cable ≤ 100 V (Peak value, not for high-power applications) Test voltage Core/Core 700 V (50 Hz, 1 min.) Test voltage Core/Shield 700 V (50 Hz, 1 min.) Current carrying capacity of cable 2 A (according to DIN VDE 0891-1) Minimum bending radius, fixed installation 4 x D Minimum bending radius, flexible installation 8 x D Smallest bending radius, fixed installation 26 mm Smallest bending radius, movable installation 52 mm Tensile strength ≤ 80 N 65.3 dB (with 1 MHz) 56.3 dB (at 4 МHz) 50.3 dB (at 10 MHz) 47.2 dB (at 16 MHz) 45.8 dB (at 20 МHz) 42.9 dB (at 31.25 МHz) 38.4 dB (at 62.5 МHz) Near end crosstalk attenuation (NEXT) 35.3 dB (at 100 MHz) 62.3 dB (with 1 MHz) 53.3 dB (at 4 МHz) 47.3 dB (at 10 MHz) 44.2 dB (at 16 MHz) 42.8 dB (at 20 МHz) 39.9 dB (at 31.25 МHz) 35.4 dB (at 62.5 МHz) Power-summated near end crosstalk attenuation (PSNEXT) 32.3 dB (at 100 MHz) 23 dB (at 4 МHz) 24.1 dB (at 8 МHz) 25 dB (at 10 MHz) 25 dB (at 16 MHz) 25 dB (at 20 МHz) 23.6 dB (at 31.25 МHz) 21.5 dB (at 62.5 МHz) Return loss (RL) 20.1 dB (at 100 MHz) 3.2 dB (with 1 MHz) 6 dB (at 4 МHz) Shield attenuation SACCBP-MSD-4CON-PG9/1,0-931SCO - Device connector, rear mounting 1437737 https://www.phoenixcontact.com/us/products/1437737 Oct 6, 2023, 5:57 AM Page 5 (14)

9.5 dB (at 10 MHz) 12.1 dB (at 16 MHz) 13.6 dB (at 20 МHz) 17.1 dB (at 31.25 МHz) 24.8 dB (at 62.5 МHz) 32 dB (at 100 MHz) Halogen-free according to IEC 60754-1 according to IEC 60332-1-2 in acc. to UL VW1 Flame resistance in accordance with UN ECE-R 118.03 Resistance to oil in accordance with EN 60811-2-1 -40 °C ... 80 °C (cable, fixed installation)Ambient temperature (operation) -20 °C ... 80 °C (Cable, flexible installation) Ambient temperature (installation) -20 °C ... 80 °C Environmental and real-life conditions Ambient conditions IP67 (When plugged in) IP65 (When plugged in) Degree of protection IP65/IP67 -25 °C ... 85 °C (Plug / socket)Ambient temperature (operation) -40 °C ... 85 °C (without mechanical actuation) Standards and regulations M12 Standard designation M12 connector Standards/specifications IEC 61076-2-101 SACCBP-MSD-4CON-PG9/1,0-931SCO - Device connector, rear mounting 1437737 https://www.phoenixcontact.com/us/products/1437737 Oct 6, 2023, 5:57 AM Page 6 (14)

2,8 M12x1PG9 1718 Dimensional drawing Schematic diagram Pin assignment M12 male connector, 4-pos., D-coded, male side SACCBP-MSD-4CON-PG9/1,0-931SCO - Device connector, rear mounting 1437737 https://www.phoenixcontact.com/us/products/1437737 Oct 6, 2023, 5:57 AM Page 7 (14)

13,5 1x45° Ø15,3 max.4,5 +0,1 +0,1 Housing cutout for Pg9 fastening thread, mounting panel with feed-through hole (alternatively with surface as protection against rotation) SACCBP-MSD-4CON-PG9/1,0-931SCO - Device connector, rear mounting 1437737 https://www.phoenixcontact.com/us/products/1437737 Oct 6, 2023, 5:57 AM Page 8 (14)

1 WH/OG

2 WH/GN

SACCBP-MSD-4CON-PG9/1,0-931SCO - Device connector, rear mounting 1437737 https://www.phoenixcontact.com/us/products/1437737 Oct 6, 2023, 5:57 AM Page 9 (14)

To download certificates, visit the product detail page: https://www.phoenixcontact.com/us/products/1437737  UL Recognized Approval ID: E118976-20100522 Nominal voltage UN Nominal current IN Cross section AWG Cross section mm2 30 V 1.5 A - 26 -  EAC Approval ID: B.01687 SACCBP-MSD-4CON-PG9/1,0-931SCO - Device connector, rear mounting 1437737 https://www.phoenixcontact.com/us/products/1437737 Oct 6, 2023, 5:57 AM Page 10 (14)

ECLASS-11.0 27440102 ECLASS-12.0 27440116 ECLASS-13.0 27440116 ETIM ETIM 8.0 EC002635 UNSPSC UNSPSC 21.0 39121400 SACCBP-MSD-4CON-PG9/1,0-931SCO - Device connector, rear mounting 1437737 https://www.phoenixcontact.com/us/products/1437737 Oct 6, 2023, 5:57 AM Page 11 (14)

Environmental product compliance REACh SVHC Lead 7439-92-1 Environmentally Friendly Use Period = 50 yearsChina RoHS For information on hazardous substances, refer to the manufacturer’s declaration available under “Downloads” SACCBP-MSD-4CON-PG9/1,0-931SCO - Device connector, rear mounting 1437737 https://www.phoenixcontact.com/us/products/1437737 Oct 6, 2023, 5:57 AM Page 12 (14)

SACC-M16-SEALING PLUG SET - Screw plug 1453368 https://www.phoenixcontact.com/us/products/1453368 Screw plug, Rear mounting, M16 x 1.5, Alternative product in accordance with RoHS II without Exemption 6c (Pb <0.1%) item no.: 1239800 PROT-M12 FS - Sealing cap 1560251 https://www.phoenixcontact.com/us/products/1560251 M12 sealing cap for unoccupied M12 plugs of the sensor/actuator cable, flush- type plugs and I/O devices in the field SACCBP-MSD-4CON-PG9/1,0-931SCO - Device connector, rear mounting 1437737 https://www.phoenixcontact.com/us/products/1437737 Oct 6, 2023, 5:57 AM Page 13 (14)

PROT-M12 FS-M - Sealing cap 1430488 https://www.phoenixcontact.com/us/products/1430488 M12 metal sealing cap for unoccupied M12 plugs of the sensor/actuator cable, flush-type plugs and I/O devices in the field SACC-M16-SEAL CLM - Flat gasket 1430394 https://www.phoenixcontact.com/us/products/1430394 M16 flat gasket for M12 flush-type connectors with M16 fastening thread Phoenix Contact 2023 © - all rights reserved https://www.phoenixcontact.com Phoenix Contact USA

586 Fulling Mill Road

Middletown, PA 17057, United States (+717) 944-1300 info@phoenixcon.com SACCBP-MSD-4CON-PG9/1,0-931SCO - Device connector, rear mounting 1437737 https://www.phoenixcontact.com/us/products/1437737 Oct 6, 2023, 5:57 AM Page 14 (14)