10T6AW4 GAPTEC | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 5

Technical content

GAPTEC-Electronic GmbH & Co. KG sales@gaptec-electronic.com – www.gaptec-electronic.com Page 1 of 5 10T6AW4_1.5 – Rev. 2019-1.0 Specifications subject to change without notice. 10T6AW4_1.5 Series 10W - Dual/Single Output - 4:1 Wide Input - Isolated & Regulated DC-DC Converter 4:1 wide input voltage range Efficiency up to 88% 1500VDC/500VAC Isolation Short circuit protection (SCP) Input under-voltage, over- current, over-voltage protection Operating temperature: -40°C to +85°C Industry standard pinout RoHS compliance No-load power consumption as low as 0.096W DC-DC Converter 10 Watt The 10T6AW4_1.5 series are isolated 10W DC-DC products with 4:1 input voltage, 500VAC/1500VDC isolation, input under-voltage protection, output over-voltage, over-current and short circuit protection, which make them widely applied in industrial control, electricity, instruments and communication fields. Example: 10T6AW4_2405S1.5 10= 10Watt; T6= SMT6; A= series; W4= wide input (4:1) 9-36Vin; 5Vout; S= Single output; 1.5= 1500VDC Isolation specifications Item Test condition Min Typ Max Units Isolation voltage (Tested for 1 minute and leakage current less than 5mA)

  • Input-output
  • Input/Output-case (for models with case)
  • Input-output
  • Input/Output-case (for models with case) 1500 1500 500 500 VDC VDC VAC VAC Isolation resistance (Test at 500VDC)
  • Input-output
  • Input/Output-case (for models with case) 1000 MΩ Isolation capacitance Input/Output, 100KHz/0.1V 1000 pF Output specifications Item Test condition Min Typ Max Units Output voltage accuracy ±1 ±3 % Line regulation Full load, input voltage from low to high ±0.2 ±0.5 % Load regulation 5% to 100% load ±0.5 ±1.0 % Transient recovery time 25% load step change 300 500 µs Transient response deviation 25% load step change ±3 ±5 % Temperature coefficient 100% load ±0.03 %/°C Ripple & Noise* 20MHz Bandwidth 50 100 mVp-p Trim Nominal input voltage ±5 %Vo Over Voltage Protection Input voltage range 110 160 %Vo Over Voltage Protection Input voltage range 110 140 200 %Io Switching frequency** PWM mode 350 KHz * Test ripple and noise by “parallel cable” method. See detailed operation instructions at Testing of Power Converter section, application notes. ** This series of products using reduced frequency technology, the switching frequency is test value of full load. When the load is reduced to below 50%, the switching frequency decreases with decreasing load. Common specifications Short circuit protection: Continuous, automatic recovery Temperature rise at full load: 40°C TYP Cooling: Free air convection Operation temperature range: -40°C~+85°C Storage temperature range: -55°C ~+125°C Pin welding resistance temperature: 300°C MAX, 1.5mm from case for 10 sec Reflow soldering temperature: (Only for models with housing) Peak temp. ≤245°C, maximum duration time ≤60s at 217°C. For actual application, please refer to IPC/JEDEC J-STD-020D.1. Vibration: 10-55Hz, 10G, 30 Min. along X, Y and Z Storage humidity range: < 95% Case material: Aluminium Alloy MTBF: >1,000,000 hours Weight: 6.7g /5.7g (without case) Input specifications Item Test condition Min Typ Max Units Input current (full load / no load) Nominal input voltage
  • 5VDC input
  • 12VDC input
  • 15VDC input mA mA mA Reflected ripple current Nominal input voltage 40 mA Surge voltage 1sec. max. -0.7 50 VDC Starting voltage 9 VDC Shutdown voltage 5.5 6.5 VDC Input filter Pi Hot plug unavailable Ctrl* (operating temperature range)
  • Models ON
  • Models OFF
  • Input current when switched off (@25°C) Ctrl pin connected to GND or low level (0-1.2VDC) Ctrl pin suspended or connected to High level (2.4-12VDC) 6mA (TYP) * The voltage of Ctrl pin is relative to input pin GND.

GAPTEC-Electronic GmbH & Co. KG sales@gaptec-electronic.com – www.gaptec-electronic.com Page 2 of 5 10T6W4_1.5 – Rev. 2019-1.0 Specifications subject to change without notice. 10T6W4_1.5 Series 10W - Dual/Single Output - 4:1 Wide Input - Isolated & Regulated DC-DC Converter Part Number Input Voltage [VDC] Nominal Range Max* Output Voltage [VDC] Output Current [mA] Max Min Capacitive load [µF, max.] Efficiency** [%, Typ.] 10T6AW4_2405S1.5 24 9-36 40 5 2000 0 2200 84 10T6AW4_2412S1.5 24 9-36 40 12 833 0 680 87 10T6AW4_2415S1.5 24 9-36 40 15 667 0 470 88 * Absolute maximum rating without damage on the converter, but it isn‘t recommended; ** Efficiency is measured In nominal input voltage and rated output load. Notes: SMD package without housing: 10TF6AW_xxyyS1.5RP EMC specifications EMI CE CISPR22/EN55022 CLASS A (bare component) CLASS B (see EMC recommended circuit ①) EMI RE CISPR22/EN55022 CLASS A (Without External Circuit) CLASS B (see EMC recommended circuit ②) EMS ESD IEC/EN61000-4-2 Contact ±4KV perf. Criteria B EMS RS IEC/EN61000-4-3 10V/m perf. Criteria A EMS EFT IEC/EN61000-4-4 ±2KV (see EMC recommended circuit ①) perf. Criteria B EMS Surge IEC/EN61000-4-5 line to line ±2KV (see EMC recommended circuit ①) perf. Criteria B EMS CS IEC/EN61000-4-6 3 Vr.m.s perf. Criteria A Typical characteristics

GAPTEC-Electronic GmbH & Co. KG sales@gaptec-electronic.com – www.gaptec-electronic.com Page 3 of 5 10T6W4_1.5 – Rev. 2019-1.0 Specifications subject to change without notice. 10T6W4_1.5 Series 10W - Dual/Single Output - 4:1 Wide Input - Isolated & Regulated DC-DC Converter Efficiency 10T6AW4_2405D1.5 10T6AW4_2415S1.5 10T6AW4_2405D1.5 10T6AW4_2415S1.5 Recommended circuit Recommended Circuit All the DC/DC converters of this series are tested according to the re - commended circuit (see Fig. 1) before delivery. If it is required to further reduce input and output ripple, properly increase the input & output of additional capacitors Cin and Cout or select capacitors of low equivalent impedance provided that the capacitance is no larger than the max. capacitive load of the product. Figure 1

GAPTEC-Electronic GmbH & Co. KG sales@gaptec-electronic.com – www.gaptec-electronic.com Page 4 of 5 10T6W4_1.5 – Rev. 2019-1.0 Specifications subject to change without notice. 10T6W4_1.5 Series 10W - Dual/Single Output - 4:1 Wide Input - Isolated & Regulated DC-DC Converter EMC solution-recommended circuit Trim Note: Part ① in the Fig. 2 is used for EMI test and part ② for EMC filtering; selected based on needs. For models with housing: the housing should be connected to input pin GND when testing EMC performance. Figure 2 It is not allowed to connect modules output in parallel to enlarge the power. Application of Trim and calculation of Trim resistance Calculation formula of Trim resistance: Model Vin: 24V FUSE Choose according to actual input current C0 680µF/100V C1/C3/C4 4.7µF/50V C2 470µF/100V C5 10µF/25V LCM 3.3µH CY1, CY2 1000pF/≥2000VDC

GAPTEC-Electronic GmbH & Co. KG sales@gaptec-electronic.com – www.gaptec-electronic.com Page 5 of 5 10T6W4_1.5 – Rev. 2019-1.0 Specifications subject to change without notice. 10T6W4_1.5 Series 10W - Dual/Single Output - 4:1 Wide Input - Isolated & Regulated DC-DC Converter Mechanical dimensions without housing Note: 1. The maximum capacitive load offered were tested at input voltage range and full load. 2. Unless otherwise specified, parameters in this datasheet were measured under the conditions of Ta=25°C, humidity<75%RH with nominal input voltage and rated output load. 3. All index testing methods in this datasheet are based on Company’s corporate standards. 4. We can provide product customization service, please contact our technicians directly for specific information. 5. Products are related to laws and regulations 6. Our products shall be classified according to ISO14001 and related environmental laws and regulations, and shall be handled by qualified units. Mechanical dimensions with housing