10S8W GAPTEC | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 4

Technical content

GAPTEC-Electronic GmbH & Co. KG sales@gaptec-electronic.com – www.gaptec-electronic.com Page 1 of 4 10S8W_1.5RP – Rev. 2019-1.0 Specifications subject to change without notice. 10S8W_1.5RP Series 10W - Single Output - Wide Input - Isolated & Regulated DC-DC Converter 2:1 wide input voltage range Operation temperature range: -40°C ~+ 85°C Isolation 1500VDC High Efficiency up to 88% Short circuit protection (SCP) Input under-voltage and over-current protection Industry standard pin-out EN62368 approved RoHS Compliance DC-DC Converter 10 Watt The 10S8W_1.5RP series is a family of high performanced 10W single & dual output DC-DC converters with 2:1 input voltage. They feature efficiencies up to 88%, 1500VDC isolation,operating ambient temperature of -40°C ~ +85°C, input under- voltage protection, output over-current and short circuit protection. They are widely used in applications such as medical care, industrial control, electric power, instruments, communications and other industries. Isolation specifications Item Test condition Min Typ Max Units Isolation voltage Tested for 1 second 1500 VDC Isolation resistance 500VDC, input to output 1000 MΩ Isolation capacitance Input/Output, 100KHz/0.1V 1000 pF Output specifications Item Test condition Min Typ Max Units Output accuracy 5%-100% load ±1 % Line regulation Vin= min to max, full load ±0.25 ±0.5 % Load regulation* 5% to 100% full load ±0.5 % Transient recovery time 25% Ioad step change 300 500 µs Transient response deviation 25% Ioad step change

  • 3.3/5V
  • Others Temperature drift ±0.03 %/°C Ripple & Noise* 20MHz Bandwidth
  • 3.3/5V
  • Others 120 150 mVp-p mVp-p Over current protection Input voltage range 110 160 230 %/Io * Output voltage accuracy for 0%-5% load is ±3% max.; Load regulation for 0% -100% load increases to ±3%; * 0%-5% load ripple&noise <300mV. Input specifications Item Test condition Min Typ Max Units Input current (full load/no load) 12V
  • 3.3V
  • 5V
  • Others 24V
  • 3.3V
  • 5V
  • Others mA mA mA mA mA mA Reflected ripple current 50 mA Surge voltage (1s max.)
  • 12V
  • 24V -0.7 -0.7 VDC VDC Start-up Voltage • 12V
  • 24V VDC VDC Under-voltage Protection
  • 12V
  • 24V 5.5 6.5 15.5 VDC VDC Input filter Capacitance filter Hot plug Unavailable Ctrl (The Ctrl pin voltage is referenced to input GND.) Module ON Module OFF input current when switched OFF Ctrl open circuit or connected to TTL high level (3.5-12VDC) Ctrl pin connected to GND or low level (0-1.2VDC) 6 10 mA Common specifications Short circuit protection: Continuous, automatic recovery Cooling: Free air convection Operation temperature range: -40°C~+85°C Storage temperature range: -55°C ~+125°C Storage humidity range: < 95% Soldering resistance temperature: 300°C max, 1.5mm from case for 10 sec Switching frequency: PWM mode, 500kHz typ. Case material: Epoxy [UL94-V0] MTBF (MIL-HDBK 217F): +25°C: >1000 Khours Weight: 5.5g Dimensions: 22.00×9.50×12.00 mm EMC specifications EMI CE CISPR32/EN55032 CLASS B (see EMC recommended circuit, ②) EMI RE CISPR32/EN55032 CLASS B (see EMC recommended circuit, ②) EMS ESD IEC/EN61000-4-2 Contact ±6KV perf. Criteria B EMS RS IEC/EN61000-4-3 10V/m perf. Criteria A EMS EFT IEC/EN61000-4-4 ±2KV perf. Criteria B (see EMC recommended circuit, ①) EMS Surge IEC/EN61000-4-5 line to line ±2KV perf. Criteria B (see EMC recommended circuit, ①) EMS CS IEC/EN61000-4-6 3 Vr.m.s perf. Criteria A Example: 10S8W_1205S1.5RP 10= 10Watt; S8= SIP8; W4= wide input (4:1); 9-36Vin; 5Vout; S= Single Output; 1.5= 1600VDC; R= Regulated Output; P= Short Curcuit Protection

GAPTEC-Electronic GmbH & Co. KG sales@gaptec-electronic.com – www.gaptec-electronic.com Page 2 of 4 10S8W_1.5RP – Rev. 2019-1.0 Specifications subject to change without notice. 10S8W_1.5RP Series 10W - Single Output - Wide Input - Isolated & Regulated DC-DC Converter Part Number Input Voltage [VDC] Nominal Range Max* Output Voltage [VDC] Output Current [mA, max.] Efficiency** [%, typ.] Capacitive Load [µF, max.] 10S8W_1203S1.5RP 12 9-18 20 3.3 2400 83 2200 10S8W_1205S1.5RP 12 9-18 20 5 2000 86 2200 10S8W_1209S1.5RP 12 9-18 20 9 1111 86 680 10S8W_1212S1.5RP 12 9-18 20 12 833 86 470 10S8W_1215S1.5RP 12 9-18 20 15 667 86 330 10S8W_1224S1.5RP 12 9-18 20 24 417 86 220 10S8W_2403S1.5RP 24 18-36 40 3.3 2400 85 2200 10S8W_2405S1.5RP 24 18-36 40 5 2000 88 2200 10S8W_2409S1.5RP 24 18-36 40 9 1111 88 680 10S8W_2412S1.5RP 24 18-36 40 12 833 88 470 10S8W_2415S1.5RP 24 18-36 40 15 667 88 330 10S8W_2424S1.5RP 24 18-36 40 24 417 88 220 * Exceeding the maximum input voltage may cause permanent damage; ** Efficiency is measured at nominal input voltage and rated output load. Typical characteristics Efficiency 10S8W_1205S1.5RP 10S8W_1205S1.5RP 10S8W_2405S1.5RP 10S8W_2405S1.5RP

GAPTEC-Electronic GmbH & Co. KG sales@gaptec-electronic.com – www.gaptec-electronic.com Page 3 of 4 10S8W_1.5RP – Rev. 2019-1.0 Specifications subject to change without notice. 10S8W_1.5RP Series 10W - Single Output - Wide Input - Isolated & Regulated DC-DC Converter Ripple & noise Ripple & noise EMC solution-recommended circuit All the DC/DC converters of this series are tested before delivery using the recommended circuit shown below. Please keep the wire of probe to copper as short as possible. Input and/or output ripple can be further reduced by appropriately increasing the input & output capacitor values Cin and Cout and/or by selecting capacitors with a low ESR (equivalent series resistance). Also make sure that the capacitance is not exceeding the specified max. capacitive load value of the product. We use Part ① in Fig. 4 for EMC and part ② for emissions test. Selecting based on needs. Model Vin: 12V Vin: 24V FUSE Choose according to actual input current C0, C4 330µF/35V 330µF/50V C1, C2 10µF/50V C3 22µF/50V LCM1 1.4-1.7mH CY1, CY2 1nF/2000VDC

GAPTEC-Electronic GmbH & Co. KG sales@gaptec-electronic.com – www.gaptec-electronic.com Page 4 of 4 10S8W_1.5RP – Rev. 2019-1.0 Specifications subject to change without notice. 10S8W_1.5RP Series 10W - Single Output - Wide Input - Isolated & Regulated DC-DC Converter Mechanical dimensions/footprint Note: 1. The maximum capacitive load offered were tested at input voltage range and full load; 2. Unless otherwise specified, parameters in this datasheet were measured under the conditions of Ta=25°C, humidity<75%RH with nominal input voltage and rated output load; 3. All index testing methods in this datasheet are based on company corporate standards; 4. We can provide product customization service, please contact our technicians directly for specific information; 5. Products are related to laws and regulations: see „Features“ and „EMC“; 6. Our products shall be classified according to ISO14001 and related environmental laws and regulations, and shall be handled by qualified units.