10DAW4-3 GAPTEC | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 5

Technical content

GAPTEC-Electronic GmbH & Co. KG sales@gaptec-electronic.com – www.gaptec-electronic.com Page 1 of 5 10DAW4_3 – Rev. 2017-1.0 Specifications subject to change without notice. 10DAW4_3 Series 10W - Single/Dual Output - Wide Input - Isolated & Regulated DC-DC Converter DC-DC Converter 10 Watt The 10DAW4_3 series offers 10W of output, with 4:1 ultra wide input voltage of 9-36VDC or 18-75VDC, and features 3000VDC isolation, over current, over voltage and short-circuit protection, as well as six sided metal shielding. All models are widely suited for industrial control, electric power, instruments, communication fields etc. Example: 10DAW4_2415S3 10 = 10Watt; D = DIP; A = series; W4 = wide input (4:1) 9-36Vin; 15Vout; S = single output; 3 = 3000VDC isolation Note: 1. Recommend to use module with more than 5% load, if not, the ripple of the product may exceeds the specification, but does not The maximum capacitive load offered were tested at nominal input voltage and full load; 2. Unless otherwise specified, parameters in this datasheet were measured under the conditions of Ta = 25, humidity <75%RH with nominal input voltage and rated output load; 3. All index testing methods in this datasheet are based on our Company’s corpo- rate standards; 4. The performance parameters of the product models listed in this manual are as above, but some parameters of non-standard model products may exceed the requirements mentioned above. Please contact our technicians directly for specific information; 5. We can provide product customization service; 6. Specifications are subject to change without prior notice. Common specifications Short circuit protection: Hiccup, continuous, self-recovery Cooling: Free air convection Operation temperature range: -40°C~+85°C (see typ. characteristics) Storage temperature range: -55°C~+125°C Case temperature: 105°C MAX Storage humidity range: 5% MIN, 95% MAX Pin welding resistance temperature: 300°C MAX, 1.5mm from case for 10 sec Switching frequency (PWM mode)*: 350kHz TYP Case material: Plastic (UL94-V0) MTBF (MIL-HDBK-217F@25°C): 1000 K hours MIN Weight: 24g * This series of products using reduced frequency technology, the switching frequency is test value of full load. When the load is reduced to below 50%, the switching frequency decreases with decreasing load. Isolation specifications Item Test condition Min Typ Max Units Isolation voltage Tested for 1 minute and leakage current less than 1 mA

3000 VDC

Isolation resistance Test at 500VDC 1000 MΩ Isolation capacitance 100KHz/0.1V 500 pF High efficiency up to 87% 4:1 wide input voltage range Short circuit protection (SCP) Output over voltage protection Output over current protection Input under voltage protection 3kVDC isolation Operating temperature range: -40°C ~ +85°C Six-sided metal shield Industry standard pinout Meet CISPR22/EN55022 CLASS A IEC60950, UL60950, EN60950 approval Output specifications Item Test condition Min Typ Max Units Output voltage accuracy ±1 ±3 % Line regulation Full load, Input volta- ge from low to high

  • positive output
  • negative output ±0.2 ±0.5 ±0.5 Load regulation 5% to 100% load
  • positive output
  • negative output ±0.5 ±0.5 ±1.5 Cross regulation Dual output, main circuit with 50% load, auxiliary circuit with 10%-100% load ±5 % Transient recovery time 25% load step change 300 500 µs Transient respon- se deviation 25% load step change ±3 ±5 % Temperature coefficient 100% full load ±0.03 %/°C Ripple & Noise* 20MHz Bandwidth 5% to 100% load 60 120 mVp-p Over voltage protection Input voltage range 110 130 160 %Vo Over current protection Input voltage range 110 140 190 %Vo * Ripple and noise tested by “parallel cable” method. See detailed operation instructions at Testing of Power Converter section, application notes. UL-60950-1 (E347551)

GAPTEC-Electronic GmbH & Co. KG sales@gaptec-electronic.com – www.gaptec-electronic.com Page 2 of 5 10DAW4_3 – Rev. 2017-1.0 Specifications subject to change without notice. 10DAW4_3 Series 10W - Single/Dual Output - Wide Input - Isolated & Regulated DC-DC Converter Part Number Input Voltage [VDC] Nominal Range Max(1) Output Voltage [VDC] Output Current [mA, Max] Efficiency [%, Typ.] Capacitive load [µF, Max] 10DAW4_2403S3 24 9-36 40 3.3 2400 79 5400 10DAW4_2405S3 24 9-36 40 5 2000 82 5400 10DAW4_2409S3 24 9-36 40 9 1111 85 680 10DAW4_2412S3 24 9-36 40 12 833 86 470 10DAW4_2415S3 24 9-36 40 15 667 87 330 10DAW4_2424S3 24 9-36 40 24 416 87 100 10DAW4_4803S3 48 18-75 80 3.3 2400 79 5400 10DAW4_4805S3 48 18-75 80 5 2000 82 5400 10DAW4_4812S3 48 18-75 80 12 833 86 470 10DAW4_4815S3 48 18-75 80 15 667 87 330 10DAW4_4824S3 48 18-75 80 24 416 87 100 10DAW4_2405D3 24 9-36 40 ±5 ±1000 82 1000 10DAW4_2412D3 24 9-36 40 ±12 ±416 86 330 10DAW4_2415D3 24 9-36 40 ±15 ±333 87 220 10DAW4_4805D3 48 18-75 80 ±5 ±1000 82 1000 10DAW4_4812D3 48 18-75 80 ±12 ±416 86 330 10DAW4_4815D3 48 18-75 80 ±15 ±333 87 220 1. Absolute maximum rating without damage on the converter, but it isn‘t recommended. EMC specifications EMI CE CISPR22/EN55022 CLASS A (Bare component) CLASS B (External Circuit Refer to EMC recommended circuit, 2 ) EMI RE CISPR22/EN55022 CLASS A (Bare component) CLASS B (External Circuit Refer to recommended circuit, 2 ) EMS ESD IEC/EN61000-4-2 Contact ±4KV perf. Criteria B EMS RS IEC/EN61000-4-3 10V/m perf. Criteria A EMS EFT IEC/EN61000-4-4 ±2KV perf. Criteria B (External Circuit Refer to recommended circuit, 1 ) EMS Surge IEC/EN61000-4-5 ±2KV perf. Criteria B (External Circuit Refer to recommended circuit, 1 ) EMS CS IEC/EN61000-4-6 3 Vr.m.s perf. Criteria A EMS Immunities of vol- tage dip, drop and short interruption IEC/EN61000-4-29 0%-70% perf. Criteria B Input specifications Item Test condition Min Typ Max Units Input current (full load / no-load) 24VDC input

  • 3.3V output
  • Others 48VDC input
  • 3.3V output
  • Others mA mA mA mA Reflected ripple current • 24VDC input
  • 48VDC input mA mA Surge voltage (1sec. max.)
  • 24VDC input
  • 48VDC input -0.7 -0.7 100 VDC VDC Start-up voltage • 24VDC input
  • 48VDC input VDC VDC Under voltage protection
  • 24VDC input
  • 48VDC input 5.5 6.5 15.5 VDC VDC Start-up time Nominal input & constant resistance load 10 ms Input filter Pi filter Hot plug Unavailable Ctrl (1) • Models ON
  • Models OFF
  • Input current (Models OFF) Ctrl suspended or connected to TTL high level (3.5-12VDC) Ctrl pin connected to GND or low level (0-1.2VDC) 5 8 mA 1. The voltage of Ctrl pin is relative to input pin GND.

GAPTEC-Electronic GmbH & Co. KG sales@gaptec-electronic.com – www.gaptec-electronic.com Page 3 of 5 10DAW4_3 – Rev. 2017-1.0 Specifications subject to change without notice. 10DAW4_3 Series 10W - Single/Dual Output - Wide Input - Isolated & Regulated DC-DC Converter Typical characteristics Efficiency curves 10DAW4_2405S3 10DAW4_4815S3 10DAW4_4815S3 10DAW4_2405S3

GAPTEC-Electronic GmbH & Co. KG sales@gaptec-electronic.com – www.gaptec-electronic.com Page 4 of 5 10DAW4_3 – Rev. 2017-1.0 Specifications subject to change without notice. 10DAW4_3 Series 10W - Single/Dual Output - Wide Input - Isolated & Regulated DC-DC Converter Typical application EMC solution-recommended circuit Note: In Figure 1, part 1 is used for EMS test, part 2 for EMI filtering. Choose according to requirements. Model 10DAW4_S3 10DAW4_D3 Vin: 24V Vin: 48V Vin: 24V Vin: 48V FUSE Choose according to actual input current MOV S20K30 S14K60 S20K30 S14K60 C0 680µF/50V 680µF/100V 680µF/50V 680µF/100V C1 1µF/50V 1µF/100V 1µF/50V 1µF/100V C2 330µF/50V 330µF/100V 330µF/50V 330µF/100V C3 4.7µF/50V 4.7µF/100V 4.7µF/50V 4.7µF/100V LCM 4.7mH 6.8mH C4 Refer to the Cout in Typical application CY1, CY2 1nF/3KV 1nF/3KV Figure 1 All the DC/DC converters of this series are tested according to the recommended circuit before delivery. If it is required to further reduce input and output ripple, properly increase the input & output of additional capacitors Cin and Cout or select capacitors of low equivalent impedance provided that the capacitance is no larger than the max. capacitive load of the product. Cin (µF) Cout (µF) 10 - 47 10 It is not allowed to connect modules output in parallel to enlarge the power.

GAPTEC-Electronic GmbH & Co. KG sales@gaptec-electronic.com – www.gaptec-electronic.com Page 5 of 5 10DAW4_3 – Rev. 2017-1.0 Specifications subject to change without notice. 10DAW4_3 Series 10W - Single/Dual Output - Wide Input - Isolated & Regulated DC-DC Converter Mechanical dimensions Recommended layout Note: Unit: mm[inch] Pin diameter tolerances: ±0.10mm [±0.004inch] General tolerances: ±0.50mm [±0.020inch]