10BXC-13-L2/Q

10BXC MSYSTEM | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 7

Technical content

MODEL: 10BXC http://www.m-system.co.jp/ 10BXC SPECIFICATIONS ES-0893 Rev.12 Page 1/7 High-density Signal Conditioners 10-RACK STANDARD RACK Functions & Features

• Standard 19" rack for 10-RACK signal conditioners
• Line power supplied via the rear rack bus
• Dual-redundant power supply or two independent power sources selectable with AC power supply
• Supply pressure at manifold plug
• Direct interface to various DCS with the rack connector MODEL: 10BXC-[1][2]-[3][4]

ORDERING INFORMATION

• Code number: 10BXC-[1][2]-[3][4] Specify a code from below for each [1] through [4]. (e.g. 10BXC-12-K2/Q)
• Specify the specification for option code /Q (e.g. /C01) [1] FUNCTION 1: Power distribution 2: Power distribution & pressure supply [2] CONNECTOR 0: None 1: Fujitsu FCN type I/O connector 2: Yokogawa DCS connector (MAC2 dual redundant system use) 3: Nippon Shokubai DCS connector 4: Azbil DCS AI connector 5: Azbil DCS AO connector 6: Azbil DCS AI connector (ELCO connector) 7: Azbil DCS AO connector (ELCO connector) 8: Yokogawa DCS connector (VMx/PM1 dual redundant system use) E3: Toshiba DCS SAIN1 card use (Panasonic AXM220001 used) (DISCONTINUED; replace with code "E3A".) E3A: Toshiba DCS SAIN1 card supported (Omron XG4A-2031 used) H1: Hitachi DCS connector H2: Hitachi DCS EX-CDL cable connector M-System guarantees the connecting section. [3] POWER SUPPLY UNIT AC Power K: 85 – 132 V AC; single power source (Operational voltage range 85 – 132 V, 47 – 63 Hz) K2: 85 – 132 V AC; dual-redundant power supply (Operational voltage range 85 – 132 V, 47 – 63 Hz) KK: 85 – 132 V AC; two independent power sources (Operational voltage range 85 – 132 V, 47 – 63 Hz) L: 170 – 264 V AC; single power source (Operational voltage range 170 – 264 V, 47 – 63 Hz) L2: 170 – 264 V AC; dual-redundant power supply (Operational voltage range 170 – 264 V, 47 - 63 Hz) DC Power R: 24 V DC; no power supply unit (Operational voltage range 24 V ±10 %, ripple 10 %p-p max.) AC/DC Power KR: 85 – 132 V AC / 24 V DC; two independent power sources (85 – 132 V, 47 – 63 Hz or 24V ±10 %, ripple 10 %p-p max.) (Redundant or independent power sources are recommended for long time use without interruption.) [4] OPTIONS blank: none /Q: With options (specify the specification) SPECIFICATIONS OF OPTION: Q COATING (For the detail, refer to M-System's web site.) Power supply and signal conditioner side of the main PWB are not coated. /C01: Silicone coating /C02: Polyurethane coating /C03: Rubber coating

RELATED PRODUCTS

• Blank filler plate (model: P-101)
• Connector terminal block (model: CNT)
• Special cable with 40-pin connector (model: FCN) GENERAL SPECIFICATIONS Construction: Metal plates assembly Capacity: 16 positions Connection Power input: M4 screw terminals (torque 0.8 N·m) Power alarm: M4 screw terminals (torque 0.8 N·m) Pneumatic: Rc 3/8" female (torque ≤ 12 N·m) Screw terminal: Nickel-plated brass Manifold: Aluminium alloy Isolation: I/O connector to alarm output to power to FG Power alarm output: N.C. contact turns off at power failure or failure of power units. Supplied only with dual-redundant power supply or two independent power sources

MODEL: 10BXC http://www.m-system.co.jp/ 10BXC SPECIFICATIONS ES-0893 Rev.12 Page 2/7 Power RUN LED: Light turns on in normal conditions (supplied only with dual-redundant power supply or two independent power sources) OUTPUT SPECIFICATIONS ■ Alarm Output (Supplied only with dual-redundant power supply or two independent power sources) Rated load: 250 V AC @ 3 A (cos ø = 1)

30 V DC @ 3 A (resistive load)

Maximum switching voltage: 250 V AC or 125 V DC Maximum switching power: 750 VA or 60 W Minimum load: 5 V DC @ 100 mA Mechanical life: 5 × 106 cycles (rate 180 cycles/min.) INSTALLATION Supply pressure: Refer to the data sheet for I/P transducers (power distribution & pressure supply type) Power consumption

• AC: 130 VA min.
• DC: 2.5 A min. Operating temperature: -5 to +55°C (23 to 131°F) 0 to 50°C (32 to 122°F) for AC power Operating humidity: 30 to 90 %RH (non-condensing) Mounting: JIS or EIA standard rack Weight Single power supply w/o power units: 3.0 kg (6.6 lb) with DC power type 3.5 kg (7.7 lb) with AC power type Dual-redundant or two independent power sources: 3.5 kg (7.7 lb) with AC/DC power type 4.0 kg (8.8 lb) with AC/AC power type Add 2 kg (4.4 lb) for air manifold type. PERFORMANCE Insulation resistance: ≥ 100 MΩ with 500 V DC Dielectric strength: 500 V AC @ 1 minute (I/O connector to alarm output to power)

1500 V AC @ 1 minute (power to FG)

500 V AC @ 1 minute (I/O connector or alarm output to FG,

1000 AC with power input code R)

Maximum supply pressure: 196 kPa (2 kgf/cm2, 1.96 bar, 28 psig)

MODEL: 10BXC http://www.m-system.co.jp/ 10BXC SPECIFICATIONS ES-0893 Rev.12 Page 3/7 MOUNTING REQUIREMENTS 101.6 (4.00) * 450 (17.72) 465 (18.31) 4–M5 SCREW ANGLE BRACKET Observe an appropriate wiring space below. 100 (3.94) for JIS standard CONNECTION DIAGRAM Remark 1: No.s of connectors may change with model suffix code. Remark 2: Supply pressure connection provided only for 10BXC-2. * PWR1 PWR2 SUPPLY PRESSURE COM. PWR2 ALM. OUTPUT PWR1 ALM. OUTPUT FG ■ Single Power Source, Dual-redundant Power Supply ■ Two Independent Power Sources, DC/AC Power Supply ■ Two Independent Power Sources, AC/AC Power Supply U V AC POWER 1CN1 CN2 CN3 CN4 U V AC POWER PWR1 COM. DC POWER ALM. OUTPUT PWR1 ALM. OUTPUT FG U V AC POWER 1 + DC POWER COM. PWR2 ALM. OUTPUT PWR1 ALM. OUTPUT FG U(+) V(–) POWER *Alarm output not provided for single power supply. SUPPLY PRESSURE CN1 CN2 CN3 CN4 SUPPLY PRESSURE CN1 CN2 CN3 CN4

MODEL: 10BXC http://www.m-system.co.jp/ 10BXC SPECIFICATIONS ES-0893 Rev.12 Page 4/7 DIMENSIONS unit: mm (inch) 221 (8.70) 465 (18.31) 101.6 (4.00) 7 (.28) 2 (.08) 480 (18.90) 435 (17.13) 8.5 (.33) 3–M4 POWER TERMINAL * PWR1 only for AC single power supply. Alarm output provided only for dual-redundant power supply or two independent power sources. *Pneumatic connection provided only for model 10BXC-2. PWR2 1 2 3 4 5 4 5 6 PWR1 1 2 3 4 5 5–M4 POWER UNIT TERMINAL 3–M4 ALARM ** OUTPUT TERMINAL POWER UNIT *POWER 1 LED POWER 2 LED 8.5 (.33)8.2 (.32) CONNECTORS SUPPLY CONNECTION Rc 3/8” * AIR MANIFOLD * 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

MODEL: 10BXC http://www.m-system.co.jp/ 10BXC SPECIFICATIONS ES-0893 Rev.12 Page 5/7 I/O CONNECTOR PIN ASSIGNMENT PIN NO. ASSIGNMENT PIN NO. ASSIGNMENT A 1 ch. 1 + B 1 ch. 1 – A 2 ch. 2 + B 2 ch. 2 – A 3 ch. 3 + B 3 ch. 3 – A 4 ch. 4 + B 4 ch. 4 – A 5 ch. 5 + B 5 ch. 5 – A 6 ch. 6 + B 6 ch. 6 – A 7 ch. 7 + B 7 ch. 7 – A 8 ch. 8 + B 8 ch. 8 – A 9 ch. 9 + B 9 ch. 9 – A10 ch.10 + B10 ch.10 – A11 ch.11 + B11 ch.11 – A12 ch.12 + B12 ch.12 – A13 ch.13 + B13 ch.13 – A14 ch.14 + B14 ch.14 – A15 ch.15 + B15 ch.15 – A16 ch.16 + B16 ch.16 – A17 – A20, B17 – B20: Unused Fujitsu FCN type I/O connector • Connector Pin Assignment CN1: Fujitsu FCN-364P040-AU The input or output 2 (output 1 with single output type) is connected to the connector. RACK LOCATION NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 VM1/PM1/VM4 CARD INPUT or OUTPUT CN3 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 VM2 CARD INPUT NO. VM2 CARD OUTPUT NO.

3 N C3 N C

1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 i o i o i o i o i o i o i o i o MAC2/PAC CARD I/O (i = input, o = output) CN1, CN2 Yokogawa DCS connector • Location I/O connector : PS-40PE-D4T1-PN1 CN1 : MAC2 / PAC card use* CN2 : MAC2 / PAC card use* for redundancy CN3 : VMx / PM1 card use** The input or output 2 (output 1 with single output type) is connected to the connector. I/O card used for control I/O. Composed of 8 inputs and 8 outputs. Input and output are paired. (Replace with pulse inputs for PAC card.) VM1: analog input 16 points VM2: analog input 8 points / analog output 8 points VM4: analog output 16 points PM1: pulse input 16 points *MAC2 card (uses KS1 cable) **VMx / PM1 card (uses KS2 cable) PIN NO. ASSIGNMENT PIN NO. ASSIGNMENT 1 No Connection 19 ch. 8 – 2 No Connection 20 ch. 8 + 3 ch.16 – 21 ch. 7 – 4 ch.16 + 22 ch. 7 + 5 ch.15 – 23 ch. 6 – 6 ch.15 + 24 ch. 6 + 7 ch.14 – 25 ch. 5 – 8 ch.14 + 26 ch. 5 + 9 ch.13 – 27 ch. 4 – 10 ch.13 + 28 ch. 4 + 11 ch.12 – 29 ch. 3 – 12 ch.12 + 30 ch. 3 + 13 ch.11 – 31 ch. 2 – 14 ch.11 + 32 ch. 2 + 15 ch.10 – 33 ch. 1 – 16 ch.10 + 34 ch. 1 + 17 ch. 9 – 18 ch. 9 + RACK LOCATION NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 NIPPON SHOKUBAI DCS LOCATION NO. Nippon Shokubai DCS connector • Location CN1 : HIF3F-34PA-2.54DSA The input or output 2 (output 1 with single output type)is connected to the connector.

• Connector Pin Assignment Azbil DCS AI connector I/O cable : J-RSL / J-RSK J-RRL / J-RRK Location Input connector : 57GE-40500-751 CN1, CN2: J-HAM50 / J-HMM00 module use The output 2 (output 1 with single output type) is connected to the connector. The CN1 and CN2 are connected in parallel. RACK LOCATION NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 AZBIL DCS AI CONNECTOR

MODEL: 10BXC http://www.m-system.co.jp/ 10BXC SPECIFICATIONS ES-0893 Rev.12 Page 6/7 RACK LOCATION NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 AZBIL DCS AO CONNECTOR Azbil DCS AO connector I/O cable : J-RSL / J-RSK J-RRL / J-RRK Location Output connector : 57GE-40500-751 CN1, CN2: J-AOM10 module use The input is connected to the connector. The CN1 and CN2 are connected in parallel. Install the Extender Module (model: 10BW) to unused channels in order to close the circuit. Azbil DCS AI connector I/O cable : J-SSL / J-SSK J-SRL / J-SRK Location Input connector : 00-8016-056-296-707V CN1, CN2: J-HAM50 / J-HMM00 module use The output 2 (output 1 with single output type) is connected to the connector. The CN1 and CN2 are connected in parallel. RACK LOCATION NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 AZBIL DCS AI CONNECTOR RACK LOCATION NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 AZBIL DCS AO CONNECTOR Azbil DCS AO connector I/O cable : J-SSL / J-SSK J-SRL / J-SRK Location Output connector : 00-8016-056-296-707V CN1, CN2: J-AOM10 module use The input is connected to the connector. The CN1 and CN2 are connected in parallel. Install the Extender Module (model: 10BW) to unused channels in order to close the circuit. RACK LOCATION NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 VM1/PM1/VM4 CARD INPUT or OUTPUT CN1, CN2 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 VM2 CARD INPUT NO. VM2 CARD OUTPUT NO. CN1, CN2 CN1, CN2 Yokogawa DCS connector • Location I/O connector : PS-40PE-D4T1-PN1 CN1 : VMx / PM1 card use (uses KS2 cable) CN2 : VMx / PM1 card use for redundancy The input or output 2 (output 1 with single output type) is connected to the connector. VM1: analog input 16 points VM2: analog input 8 points / analog output 8 points VM4: analog output 16 points PM1: pulse input 16 points PIN NO. ASSIGNMENT PIN NO. ASSIGNMENT 40 ch. 1 + 24 ch. 9 + 39 ch. 1 – 23 ch. 9 – 38 ch. 2 + 22 ch.10 + 37 ch. 2 – 21 ch.10 – 36 ch. 3 + 20 ch.11 + 35 ch. 3 – 19 ch.11 – 34 ch. 4 + 18 ch.12 + 33 ch. 4 – 17 ch.12 – 32 ch. 5 + 16 ch.13 + 31 ch. 5 – 15 ch.13 – 30 ch. 6 + 14 ch.14 + 29 ch. 6 – 13 ch.14 – 28 ch. 7 + 12 ch.15 + 27 ch. 7 – 11 ch.15 – 26 ch. 8 + 10 ch.16 + 25 ch. 8 – 9 ch.16 – 1 – 8: Unused

• Connector Pin Assignment Toshiba DCS SAIN1 card use • Location Input connector : Omron XG4A-2031 CN1 : SAIN1 (ch.1 – ch.8) CN2 : SAIN1 (ch.1 – ch.8) for redundancy CN3 : SAIN1 (ch.9 – ch.16) CN4 : SAIN1 (ch.9 – ch.16) for redundancy The output 2 (output 1 with single output type) is connected to the connector. RACK LOCATION NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 CN1, CN2 CN3, CN4 SAIN1 INPUT POINT NO. Toshiba DCS SAMP1 uses Panasonic AXM220001. As connector is discontinued, Omron XG4A-2031 is used as an alternative. (Replace cable side.)

MODEL: 10BXC http://www.m-system.co.jp/ 10BXC SPECIFICATIONS ES-0893 Rev.12 Page 7/7 PIN NO. ASSIGNMENT PIN NO. ASSIGNMENT 1 ch. 1 + 9 ch. 9 + 19 ch. 1 – 27 ch. 9 – 2 ch. 2 + 10 ch.10 + 20 ch. 2 – 28 ch.10 – 3 ch. 3 + 11 ch.11 + 21 ch. 3 – 29 ch.11 – 4 ch. 4 + 12 ch.12 + 22 ch. 4 – 30 ch.12 – 5 ch. 5 + 13 ch.13 + 23 ch. 5 – 31 ch.13 – 6 ch. 6 + 14 ch.14 + 24 ch. 6 – 32 ch.14 – 7 ch. 7 + 15 ch.15 + 25 ch. 7 – 33 ch.15 – 8 ch. 8 + 16 ch.16 + 26 ch. 8 – 34 ch.16 – Hitachi DCS connector • Location CN1, CN2: DN20B-36S The input or output 2 (Output 1 with single output type) is connected to the connector. RACK LOCATION NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 HITACHI DCS CONNECTOR Connector Pin Assignment PIN NO. ASSIGNMENT PIN NO. ASSIGNMENT 1 ch. 1 + 9 ch. 9 + 19 ch. 1 – 27 ch. 9 – 2 ch. 2 + 10 ch.10 + 20 ch. 2 – 28 ch.10 – 3 ch. 3 + 11 ch.11 + 21 ch. 3 – 29 ch.11 – 4 ch. 4 + 12 ch.12 + 22 ch. 4 – 30 ch.12 – 5 ch. 5 + 13 ch.13 + 23 ch. 5 – 31 ch.13 – 6 ch. 6 + 14 ch.14 + 24 ch. 6 – 32 ch.14 – 7 ch. 7 + 15 ch.15 + 25 ch. 7 – 33 ch.15 – 8 ch. 8 + 16 ch.16 + 26 ch. 8 – 34 ch.16 – Hitachi DCS EX-CDL cable connector • Location CN1 : 57GE-40360-751 (D7A) The input or output 2 (output 1 with single output type) is connected to the connector. Specifications are subject to change without notice.