105XB7D

105XB7D HB | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 6

Technical content

Hebei I.T. (Shanghai) Co., Ltd. Part No.：105XB7D www.ledz.com LED SPECIFICATION CATHODE 2.54±0.1 1.5±0.5 25.4Min 13.6 2.0 10.8 9.8 1.0Max 0.5±0.1 Ø Features/特征： l Single color/ 单色 l High bright output/ 高亮度输出 l Low power consumption/ 低功耗 l High reliability and long life/ 可靠性高、寿命长 Ø Descriptions/描述： l Dice material/ 芯片材质：InGaN l Emitting Color/ 发光颜色： Super Bright Blue/ 高亮度蓝色 l Device Outline/ 产品外形： φ10mm Round Type/ 10mm 圆形 l Lens Type 胶体颜色： Blue Diffused/ 蓝色散射 Ø Directivity/ 指向特性： 1. All dimensions are millimeters/单位：mm. 2. Tolerance is +/-0.20mm unless otherwise noted/ 没有标注的公差均为±0.20mm. Ta=25°C IF=20mA Radiation Angle 30° Relative Luminous 90° 60° 0.5 0° 0.5 90° 1.0 60° DIRECTIVITY 1.0 0° 30°

Hebei I.T. (Shanghai) Co., Ltd. Part No.：105XB7D www.ledz.com LED SPECIFICATION Ø Absolute maximum ratings/极限参数（Ta = 25℃） Values 数值 Parameter 参数 Symbol 符号 Test Condition 测试条件 Min. Max. Unit 单位 Reverse Voltage 反向电压 VR IR = 30μA 5 -- V Forward Current 正向工作电流 IF ---- ---- 25 mA Power Dissipation 损耗功率 Pd ---- ---- 90 mW Pulse Current 正向峰值电流 Ipeak Duty=0.1mS，1kHz ---- 100 mA Operating Temperature 工作温度范围 Topr ---- -40 +85 ℃ Storage Temperature 储存温度范围 Tstr ---- -40 +100 ℃ Ø Electrical and optical characteristics/光电参数（Ta = 25℃） Values 数值 Parameter 参数 Symbol 符号 Test Condition 测试条件 Min. Typ. Max. Unit 单位 Forward Voltage 正向电压 VF IF = 20mA ---- 3.2 3.6 V Reverse Current 反向电流 IR VR = 5V ---- ---- 30 μA Dominate Wavelength 主波长 λd IF = 20mA ---- 470 ---- nm Peak Wavelength 峰值波长 λp IF = 20mA ---- 468 ---- nm Spectral Line half-width 半波长宽度 Δλ IF = 20mA ---- 20 ---- nm Luminous Intensity 发光强度 IV IF = 20mA ---- 300 ---- mcd Viewing Angle 指向角度 2θ1/2 IF = 20mA ---- 50 ---- Deg.

Hebei I.T. (Shanghai) Co., Ltd. Part No.：105XB7D www.ledz.com LED SPECIFICATION Ø Typical electrical/optical characteristic curves： 400 100 Relative Luminous Intensity Wavelength λ(nm) 700650550 600500450 Fig.5 辐射强度 Vs. 波长 -20 30Forward Current(mA) Ambient Temperature TA ()℃ 00 20 40 60 80 100 IF-Forward Current (mA) Forward Current(mA) Luminous Intensity Relative Value at IF=20mA Forward Voltage(V) 3.62.4 2.8 3.2 4.0 0 0 10 20 30 0.5 2.5 1.0 1.5 2.0 40 502.0 2.5 2.0 40 60 9080 1.5 1.0 0.5 200-40 Ambient Temperature TA ()℃ Relative Luminous Intensity Fig.1 正向电流 Vs. 正向电压 Fig.2 相对亮度 Vs. 正向电流 Fig.3 正向电流 Vs. 环境温度 Fig.4 相对亮度 Vs. 环境温度

Hebei I.T. (Shanghai) Co., Ltd. Part No.：105XB7D www.ledz.com LED SPECIFICATION Ø Lead Forming/成形 1. Any lead forming or bending must be done before soldering. 支架成形必须在焊接前完成。 2. When forming leads, there must be a minimum of 2mm clearance between the base of the LED lens and the lead bend. 必需离胶体2 毫米才能折弯支架。 3. Avoid bending the leads at the same point more than once. 避免在管脚同一位置两次或多次弯。 4. During assembly onto PCB, the lead pitch of the LED must match the pitch of the mounting holes on the PCB during component placement. 支架成形需保证引脚和间距与线路板上一致。 Ø Soldering Condition/焊接条件 Careful attention should be paid during soldering. When soldering, leave more then 2mm from solder joint to case, and soldering beyond the base of the tie bar is recommended. 焊接时请特别注意，焊接点要离LED封装体底部2mm以上。 Avoiding applying any stress to the lead frame while the LEDs are at high temperature particularly when soldering. 在LED 处于高温，特别是在焊接时，请避免对支架施压。

Hebei I.T. (Shanghai) Co., Ltd. Part No.：105XB7D www.ledz.com LED SPECIFICATION Recommended soldering conditions/推荐焊接条件: Hand Soldering 手工焊接 DIP Soldering 浸焊 Temp.at tip of iron 电烙铁温度 300℃Max.(30WMax.) 最高温度300℃（功率 不超过30瓦） Preheat temp. 预热温度 100℃ Max. (60 sec Max.) 最高温度100℃（不超过60 Soldering time 焊接时间 3 sec Max. 时间不超过3秒 Bath temp. 浸焊温度 260℃ Max 最高260℃. Distance 焊接位置 2mm Min.(From solder joint to case) 大于2毫米（从焊点到 胶体） Bath time. 浸焊时间 3 sec Max. 不超过3秒 Distance 浸焊位置 2mm Min 大于2毫米. Ø Cleaning/清洗 1. Do not clean LEDs with water, Alcohol are recommended solvents for cleaning. When using other solvents, it should be confirmed beforehand whether the solvents will dissolve the resin or not. 不要用水清洗，推荐使用酒精清洗，当使用其他溶剂清洗时应事先确认该溶剂是否溶解树脂。 2. LEDs may be damaged by ultrasonic-washed. Before cleaning, a pre-test should be done to confirm whether any damage to the LEDs will occur. LED有可能在超声波清洗过程中被破坏。为了保证安全，在清洗前，请先确认。 Ø Storage/保存 1. Environmental temperature: -40℃---100℃, Recommended: -20℃---50℃ 2. Environmental humidity: 30%---70%, Recommended: 40%---60% 环境湿度：30%---70%，推荐使用40%---60%；

Hebei I.T. (Shanghai) Co., Ltd. Part No.：105XB7D www.ledz.com LED SPECIFICATION Ø Static Electricity/静电 1. Static Electricity or power surge will damage the LED. It is recommended that a wrist band or an anti-electrostatic glove be used when handling the LEDs. 静电或激增电压将损害LED。 建议使用发光二极管时佩戴手腕带或防静电手套。 2. All production machinery and test instruments must be electrically grounded. 所有的生产机器和检测仪器，必须接地。 3. Maintain a humidity level of 50% or higher in production areas. 生产现场湿度必须保持在50%或者更高。 4. Use anti-static packaging for transport and storage. 使用防静电包装，运输和储存。