103P

103P EXXELIA | Alldatasheet

Document overview

• Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
• PDF pages: 6

Technical content

Metal-Case sUbMiNiatUre 10 aMPere tHrU-Pass PaPer CaPaCitors Type 103p eleCtriCal sPeCiFiCatioNs CapaCitanCe range: 0.001 μF to 1.0 μF DC VOltage range: 200 VDC to 600 VDC CapaCitanCe tOleranCe: ±20%, ±10% Operating temperature: -55°C to +125°C VOltage Derating: At +125°C, 50% of the 85°C rating DissipatiOn FaCtOr: 1.0% maximum VOltage test: 200% of rated voltage for 2 minutes insulatiOn resistanCe: Measure at rated voltage, not to exceed 500 VDC, after a 2 minute charge.

• At +25°C, 20,000 Megohm-Microfarads, need not exceed 30,000 Megaohms
• At +85°C, 200 Megohm-Microfarads, need not exceed 300 Megaohms DC resistanCe: 0.01 ohms maximum insertiOn lOss: See table on next page CirCUit diaGraM diMeNsioNs (in inches)

FeatUres

• Bulkhead mounting
• Excellent RFI specs
• Hermetically encased
• Low inductance connection
• Low insertion loss
• Approved to MIL-PRF-11693 / 07
• 10 Amp current ratings majOr appliCatiOns: Used to suppress RF interference in the following equipment, rotating machinery, ignition systems, electromechanical devices, and electronic device. PHysiCal CHaraCteristiCs COnstruCtiOn: Non-inductive wound paper / foil, wound around a feed-thru bus. The case is the common ground of the three terminal network. Case: Hermetically sealed metal enclosure; the case and terminal styles are shown above. leaD pull: 5 lbs (2.3 kg) for one minute. No physical damage. leaD / BenD: After three complete consecutive bends. No damage. marking: Dearborn trademark, type or catalog number, capacitance, tolerance and voltage. NUT 5/16- 24UNF-2A PT. NO. 6-113 0.125 ±0.015 EXTERNAL TOOTHED LOCKWASHER -0.001 (10 .18 AWG) SOLID TINNED LEADS 1.625 +1.000 -0.000 ±0.031 ±0.031 0.312 +0.015 -0.005 0.125 MAXDIA. 1.625 +1.000 -0.000 L D CL CL 0.020 ±0.005 0.125 ±0.015 SLOT 0.062 x 0.125 0.156 0.296 ±0.062 ±0.015 0.187 ±0.015 0.020 ±0.005 CL CL SLOT x 0.125 0.312 ± 0.031 0.296 ± 0.062 -24 UNF - 2A THD5 0.156 ±0.015 0.187 ±0.015 0.060 0.050 0.255 0.250 ACROSS FLATS 0.125 ±0.015 NUT 5/16- 24UNF-2A PT. NO. 6-113 0.125 ±0.015 EXTERNAL TOOTHED LOCKWASHER -0.001 (10 .18 AWG) SOLID TINNED LEADS 1.625 +1.000 -0.000 ±0.031 ±0.031 0.312 +0.015 -0.005 0.125 MAXDIA. 1.625 +1.000 -0.000 L D CL CL 0.020 ±0.005 0.125 ±0.015 SLOT 0.062 x 0.125 0.156 0.296 ±0.062 ±0.015 0.187 ±0.015 0.020 ±0.005 CL CL SLOT x 0.125 0.312 ± 0.031 0.296 ± 0.062 -24 UNF - 2A THD5 0.156 ±0.015 0.187 ±0.015 0.060 0.050 0.255 0.250 ACROSS FLATS 0.125 ±0.015

μF Catalog no.* inches millimeters tab. term Wire lead D l D l

200 VDC

300 VDC

400 VDC

600 VDC

*The catalog numbers given are for capacitance tolerance of ± 20%. To specify ± 10% tolerance, change X0 to X9. Mounting hardware furnished unassembled. Metal-Case sUbMiNiatUre 10 aMPere tHrU-Pass PaPer CaPaCitors Type 103p eleCtriCal CHaraCteristiCs Vs. teMPeratUre iNsertioN loss CHaraCteristiCs For ideal CaPaCitors These capacitors are designed to meet all the electrical, mechanical, and environmental requirements of Military Specification MIL-PRF-11693. The insertion loss of such capacitors is defined by this military specification as follows. “...the insertion loss shall be not more than 6 decibels (dB) permissible dips below the value shown on the graph above for an ideal capacitor of the same nominal capacitance value, when tested at frequencies from 0.15 megahertz (MHz) up to that frequency at which the insertion loss of the capacitor under test becomes 60 dB; at all higher frequencies, up to 1,000MHz, the insertion loss shall not fall below 60 dB. Deviations in the nature of dips in the curve will be permitted; such dips indicate a drop in insertion loss below that of an ideal capacitor followed by a rise in insertion loss, as frequency is increased, faster than the rise that is characteristic of an ideal capacitor. Such dips are characteristic of all extended foil capacitors.” Capacitance Change Envelope For 95% Confidence Level % Capaticance Change - 1000Hz Temperature (°C) % Dissipation Factor - 1000Hz Temperature (°C) 2.5 2.0 1.5 1.0 0.5 TYPICAL 101.01 .0 1,000100 Insertion Loss (dB) 0 2.0 µF 1.0 µF 0.47 µF 0.22 µF 0.1 µF 0.047 µF 0.022 µF 0.01 µF 0.0047 µF 0.0022 µF 0.00 1 µF Frequency (MHz) Capacitance Change Envelope For 95% Confidence Level % Capaticance Change - 1000Hz Temperature (°C) % Dissipation Factor - 1000Hz Temperature (°C) 2.5 2.0 1.5 1.0 0.5 TYPICAL

typical characteristics polyester Film / Foil types INSuLATION RESISTANCE VS. TEMPERATuRECAPACITANCE CHANgE VS. TEMPERATuRE typical characteristics -.4 -50 -25 02 55 07 51 00 125 % Capacitance Change Temperature (°C) Capacitance Change Vs Temperature Polyester Film/foil Temperature (°C) Temperature (°C) 1.4 1.2 0.8 0.6 0.4 0.2 -50 -25 02 55 07 5 100 125 % Dissipation Factor Dissipation Factor Vs. Temperature Polyester Film/foil Measured at 1kHz 1,000,000 100,000 10,000 1,000 100 25 45 65 85 1051 25 Megaohms X Microfarads Typical Insulation Resistance Vs. Temperature Polyester Film/foil DISSIPATION FACTOR VS. TEMPERATuRE -.4 -50 -25 02 55 07 51 00 125 % Capacitance Change Temperature (°C) Capacitance Change Vs Temperature Polyester Film/foil Temperature (°C) Temperature (°C) 1.4 1.2 0.8 0.6 0.4 0.2 -50 -25 02 55 07 5 100 125 % Dissipation Factor Dissipation Factor Vs. Temperature Polyester Film/foil Measured at 1kHz 1,000,000 100,000 10,000 1,000 100 25 45 65 85 1051 25 Megaohms X Microfarads Typical Insulation Resistance Vs. Temperature Polyester Film/foil -.4 -50 -25 02 55 07 51 00 125 % Capacitance Change Temperature (°C) Capacitance Change Vs Temperature Polyester Film/foil Temperature (°C) Temperature (°C) 1.4 1.2 0.8 0.6 0.4 0.2 -50 -25 02 55 07 5 100 125 % Dissipation Factor Dissipation Factor Vs. Temperature Polyester Film/foil Measured at 1kHz 1,000,000 100,000 10,000 1,000 100 25 45 65 85 1051 25 Megaohms X Microfarads Typical Insulation Resistance Vs. Temperature Polyester Film/foil

1.625 +1.00 -0.00 ±0.031 +0.015 -0.005 0.172 Max. L D L ±0.31 -0.000 1.625 +1.000 0.172 Max. +0.015 -0.005D INSULATING SLEEVE

0.0075 MAX THICKNESS

0.020 ±0.015 SOLID TINNED LEADS SECTION INSULATED FROM CASE DIMENSIONS IN INCHES CASE STYLE 02 CASE STYLE 04 ±0.031L ±0.015 -0.005D DIA 0.172 Max. 1.625 +1.000 -0.000 ±0.005 A DIA C B 0.033 ±0.005 FOR 0.400 DIA., 0.051 ±0.005 FOR DIA. 0.500 AND LARGER W WRAP-AROUND APPROX. 135° FOR 0.400 DIA., AND APPROX. 225° FOR LARGER DIA. ±0.015 CL CASE STYLE 13 ±0.031 L ±0.015 -0.005D DIA 0.172 Max. 1.625 +1.00 1.625 +1.00 0.020 L ±0.062-0 1.625 +1.00 1.625 +1.00 0.172 Max. +0.015 -0.037D DIA. INSULATING SLEEVE 0.0075 MAX. THICKNESS ±0.015 0.020 ±0.015 SECTION GROUNDED TO CASE DIMENSIONS IN INCHES CASE STYLE 01 CASE STYLE 03 ±0.031 L +0.015 -0.005D DIA 0.172 Max. 1.625 +1.00 -0 1.625 +1.00 ±0.005 DIA A C B 0.033 ±0.005 FOR 0.400 DIA., 0.051 ±0.005 FOR DIA. 0.500 AND LARGER W ±0.015 CL CASE STYLE 12 The length of grounded styles is 0.062" shorter than the length shown in tabulations in the catalog" section insulated From casesection Grounded to case DIMENSIONS (in inches) The length of grounded styles is 0.062” shorter than the length shown in tabulations in the catalog. DIMENSIONS (in inches) 1.625 +1.00 -0.00 ±0.031 +0.015 -0.005 0.172 Max. L D L ±0.31 -0.000 1.625 +1.000 0.172 Max. +0.015 -0.005D INSULATING SLEEVE 0.020 ±0.015 SOLID TINNED LEADS SECTION INSULATED FROM CASE DIMENSIONS IN INCHES CASE STYLE 02 CASE STYLE 04 ±0.031L ±0.015 -0.005D DIA 0.172 Max. 1.625 +1.000 -0.000 ±0.005A DIA C B 0.033 ±0.005 FOR 0.400 DIA., 0.051 ±0.005 FOR DIA. 0.500 AND LARGER W WRAP-AROUND APPROX. 135° FOR 0.400 DIA., AND APPROX. 225° FOR LARGER DIA. ±0.015 CL CASE STYLE 13 ±0.031 L ±0.015 -0.005D DIA 0.172 Max. 1.625 +1.00 1.625 +1.00 0.020 L ±0.062-0 1.625 +1.00 1.625 +1.00 0.172 Max. +0.015 -0.037D DIA. INSULATING SLEEVE 0.0075 MAX. THICKNESS ±0.015 0.020 ±0.015 SECTION GROUNDED TO CASE DIMENSIONS IN INCHES CASE STYLE 01 CASE STYLE 03 ±0.031 L +0.015 -0.005D DIA 0.172 Max. 1.625 +1.00 -0 1.625 +1.00 ±0.005 DIA A C B 0.033 ±0.005 FOR 0.400 DIA., 0.051 ±0.005 FOR DIA. 0.500 AND LARGER W ±0.015 CL CASE STYLE 12 The length of grounded styles is 0.062" shorter than the length shown in tabulations in the catalog" 1.625 +1.00 -0.00 ±0.031 +0.015 -0.005 0.172 Max. L D L ±0.31 -0.000 1.625 +1.000 0.172 Max. +0.015 -0.005D INSULATING SLEEVE 0.020 ±0.015 SOLID TINNED LEADS SECTION INSULATED FROM CASE DIMENSIONS IN INCHES CASE STYLE 02 CASE STYLE 04 ±0.031L ±0.015 -0.005D DIA 0.172 Max. 1.625 +1.000 -0.000 ±0.005A DIA C B 0.033 ±0.005 FOR 0.400 DIA., 0.051 ±0.005 FOR DIA. 0.500 AND LARGER W WRAP-AROUND APPROX. 135° FOR 0.400 DIA., AND APPROX. 225° FOR LARGER DIA. ±0.015 CL CASE STYLE 13 ±0.031 L ±0.015 -0.005D DIA 0.172 Max. 1.625 +1.00 1.625 +1.00 0.020 L ±0.062-0 1.625 +1.00 1.625 +1.00 0.172 Max. +0.015 -0.037D DIA. INSULATING SLEEVE 0.0075 MAX. THICKNESS ±0.015 0.020 ±0.015 SECTION GROUNDED TO CASE DIMENSIONS IN INCHES CASE STYLE 01 CASE STYLE 03 ±0.031 L +0.015 -0.005D DIA 0.172 Max. 1.625 +1.00 -0 1.625 +1.00 ±0.005 DIA A C B 0.033 ±0.005 FOR 0.400 DIA., 0.051 ±0.005 FOR DIA. 0.500 AND LARGER W ±0.015 CL CASE STYLE 12 The length of grounded styles is 0.062" shorter than the length shown in tabulations in the catalog"

Bracket dimensions (Style 12 & 13 / in inches) D w A b C *Based on 1 in. = 25.4 mm typical taB terminal dimensions Tab Terminal available only on case diameters equal to or greater than 0.400 inches. T1 & T3 styles are supplied with one tab terminal on the insulated end and a ground lead on the opposite end. 0.020 ±0.005 0.125 ±0.015 Slot 0.062 x 0.125 AB 0.296 ±0.062 Dwg. No A-9525 cL cL TYPICAL TAB TERMINAL DIMENSIONS Tab Terminal available only on case diameters equal to or greater than 0.400 inches. T1 & T3 styles are supplied with one tab terminal on the insulated end and a ground lead on the opposite end.

EXAMPLE: wrap and Fill EXAMPLE: 218P 223 X9 100 S 02 430P 183 X9 100 X F Case style Terminal: S = Wire leads T = Soldering tab*. DC Voltage rating: Expressed in volts. See standard ratings charts for voltage code. Capacitance Tolerance: X0 = ±20% X9 = ±10% X5 = ±5% X2 = ±2% Capacitance: Expressed in picofarads, the first two digits are significant figures; the third is the number of zeros following. See standard ratings tables for capacitance code. Dearborn type number: Identifies the basic capacitor. * Soldering tabs are available only on case diameters equal to or greater then 0.400 inches. “F” applies only to “ROHS” compliant parts. Terminal: No suffix required unless specified on applicable specification sheet (Terminal style). DC Voltage rating: Expressed in volts. See standard ratings charts for voltage code. Capacitance Tolerance: X0 = ±20% X9 = ±10% X5 = ±5% X2 = ±2% Capacitance: Expressed in picofarads, the first two digits are significant figures; the third is the number of zeros following. See standard ratings tables for capacitance code. Dearborn type number: Identifies the basic capacitor. CATALOg NuMbERINg SYSTEM CATALOg NuMbERINg SYSTEM