100HBAW GAPTEC | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 3

Technical content

GAPTEC-Electronic GmbH & Co. KG sales@gaptec-electronic.com – www.gaptec-electronic.com Page 1 of 3 100HBAW – Rev. 2018-1.2 Specifications subject to change without notice. Wide Input voltage range (2:1/4:1) Typical Efficiency: 85% Input under voltage, over voltage protection Short circuit protection (SCP), auto recovery Input-output isolated PCB Board in-line type installs High power density Optional heat sink 100HBAW Series DC-DC Converter 100 Watt The 100HBAW series offers 100W of output, wide input voltage of 2:1 (9-18VDC; 18-36VDC; 36-72VDC) & 4:1 (9-36VDC; 18-72VDC), and features 1500VDC isolation, input under voltage protection, over current and short circuit protection. All models are particularly suited to tele-communications, industrial, test equipments power etc. 100W Half-Brick - Single/Dual Output DC-DC Converter - Wide Input - Isolated & Regulated Common specifications Short circuit protection*: Continuous, automatic recovery Operation temperature range: -25°C~+85°C Storage temperature range: -55°C ~+125°C Storage humidity range: < 90% Case material: Plastic [UL94-V0] / aluminium MTBF: 2,000,000 hours *Supply voltage must be discontinued at the end of short circuit duration. Isolation specifications Item Test condition Min Typ Max Units Isolation voltage Tested for 1 minute and 1mA max

1500 VDC

Note: 1. Operation under minimum load will not damage the converter; However, they may not meet all specification listed, and that will reduce the life of product. 2. All specifications measured at Ta = 25°C, humidity <75%, nominal input voltage and rated output load unless otherwise specified. 3. In this datasheet, all the test methods of indications are based on corporate standards. Example: 100HBAW_2405S1.5 W = 100 Watt; HB = Half-Brick; A = Pinning; W = Wide input (2:1); 24 = 18-36 Vin; 05 = 5Vout; S = Single Output; 1.5 = 1.5kVDC Isolation Output specifications Item Test condition Min Typ Max Units Output power 100 W Line regulation ±0.2 % Load regulation ±0.5 % Output voltage accuracy ±1.0 % Temperature coefficient ±0.02 %/°C Ripple & Noise* 20MHz Bandwidth 150 mVp- p Switching fre- quency

300 KHz

*Test ripple and noise by “parallel cable” method.

GAPTEC-Electronic GmbH & Co. KG sales@gaptec-electronic.com – www.gaptec-electronic.com Page 2 of 3 100HBAW – Rev. 2018-1.2 Specifications subject to change without notice.

100 W Half-Brick - Single/Dual Output DC-DC Converter - Wide Input - Isolated & Regulated

Part Number Input Voltage [V] Output Voltage [VDC] Output Current [A, max] 100HBAW_xx03S1.5 9-18; 18-36; 36-72 3.3 20 100HBAW_xx05S1.5 9-18; 18-36; 36-72 5 20 100HBAW_xx12S1.5 9-18; 18-36; 36-72 12 8.3 100HBAW_xx15S1.5 9-18; 18-36; 36-72 15 6.7 100HBAW_xx24S1.5 9-18; 18-36; 36-72 24 4.2 100HBAW_xx48S1.5 9-18; 18-36; 36-72 48 2.1 100HBAW4_xx03S1.5 9-36; 18-72 3.3 20 100HBAW4_xx05S1.5 9-36; 18-72 5 20 100HBAW4_xx12S1.5 9-36; 18-72 12 8.3 100HBAW4_xx15S1.5 9-36; 18-72 15 6.7 100HBAW4_xx24S1.5 9-36; 18-72 24 4.2 100HBAW4_xx48S1.5 9-36; 18-72 48 2.1

  • xx= Input Voltage 100HBAW Vin= 9-18V, xx= 12 Vin= 18-36V, xx= 24 Vin= 36-72V, xx= 48 100HBAW4 Vin= 9-36V, xx= 24 Vin= 18-72V, xx= 48 Mechanical dimensions Note: Unit: mm[inch] Pin section tolerances: ± 0.10mm [± 0.004inch] General tolerances: ± 0.25mm [±0.010inch] Pin assignment Pin S 1 +Vin

2 REM

3 CASE

5 GND

7 TRIM

GAPTEC-Electronic GmbH & Co. KG sales@gaptec-electronic.com – www.gaptec-electronic.com Page 3 of 3 100HBAW – Rev. 2018-1.2 Specifications subject to change without notice. Remote on/off control External output trim Control (Positive Logic)

  • ON • CNT Pin left open or connect to +Vin Control (Positive Logic)
  • OFF • CNT Pin connect -Vin Control (Negative Logic,Tip/P)
  • ON • CNT Pin connect -Vin Control (Negative Logic,Tip/P)
  • OFF • CNT Pin left open or connect to +Vin