156869 TI
Document overview
- PDF pages: 9
Technical content
Page 1
September 2005
LM2664
Switched Capacitor Voltage Converter
General Description
The LM2664 CMOS charge-pump voltage converter inverts a positive voltage in the range of +1.8V to +5.5V to the corresponding negative voltage of −1.8V to −5.5V. The LM2664 uses two low cost capacitors to provide up to 40 mA of output current. The LM2664 operates at 160 kHz oscillator frequency to reduce output resistance and voltage ripple. With an operating current of only 220 µA (operating efficiency greater than 91% with most loads) and 1 µA typical shutdown current, the LM2664 provides ideal performance for battery powered systems. The device is in SOT-23-6 package.
Basic Application Circuits
Features
- Inverts Input Supply Voltage
- SOT23-6 Package
- 12Ω Typical Output Impedance
- 91% Typical Conversion Efficiency at 40 mA
- 1µA Typical Shutdown Current
Applications
- Cellular Phones
- Pagers
- PDAs
- Operational Amplifier Power Suppliers
- Interface Power Suppliers
- Handheld Instruments
Voltage Inverter

+5V to −10V Converter

© 2005 National Semiconductor Corporation DS100031
Page 2
Absolute Maximum Ratings (Note 1)
If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications.
Supply Voltage (V+ to GND, or GND to OUT)
5.8V
SD
(GND −0.3V) to (V+ +
0.3V)
V+ and OUT Continuous Output Current
50 mA
Output Short-Circuit Duration to GND (Note 2)
1 sec. 600 mW
Continuous Power Dissipation (TA = 25˚C)(Note 3)
Electrical Characteristics
TJMax(Note 3)
150˚C
θJA (Note 3)
210˚C/W
Operating Junction
−40˚ to 85˚C
Temperature Range Storage Temperature Range
−65˚C to +150˚C
Lead Temp. (Soldering, 10 seconds)
300˚C
ESD Rating
2kV
Limits in standard typeface are for TJ = 25˚C, and limits in boldface type apply over the full operating temperature range. Un- less otherwise specified: V+ = 5V, C1 = C2 = 3.3 µF. (Note 4)
| Parameter | Condition | Min (Note 5) | Typ (Note 6) | Max (Note 5) | Units |
|---|---|---|---|---|---|
| Supply Voltage | 1.8 | 5.5 | V | ||
| Supply Current | No Load | 220 | 500 | µA | |
| Shutdown Supply Current | 1 | µA | |||
| Shutdown Pin Input Voltage | Normal Operation | 2.0 (Note 7) | V | ||
| Shutdown Mode | 0.8 (Note 8) | ||||
| Output Current | 40 | mA | |||
| Sum of the R of the four ds(on) internal MOSFET switches | I = 40 mA L | 4 | 8 | Ω | |
| Output Resistance (Note 9) | I = 40 mA L | 12 | 25 | Ω | |
| Oscillator Frequency | (Note 10) | 80 | 160 | kHz | |
| Switching Frequency | (Note 10) | 40 | 80 | kHz | |
| Power Efficiency | R (1.0k) between GND and L OUT | 90 | 94 | % | |
| I = 40 mA to GND L | 91 | ||||
| Voltage Conversion Efficiency | No Load | 99 | 99.96 | % |
Symbol
V+ IQ ISD VSD
IL RSW
ROUT fOSC fSW PEFF
VOEFF
Note 1: Absolute maximum ratings indicate limits beyond which damage to the device may occur. Electrical specifications do not apply when operating the device beyond its rated operating conditions. Note 2: OUT may be shorted to GND for one second without damage. However, shorting OUT to V+ may damage the device and should be avoided. Also, for temperatures above 85˚C, OUT must not be shorted to GND or V+, or device may be damaged. Note 3: The maximum allowable power dissipation is calculated by using PDMax = (TJMax −TA)/θJA, where TJMax is the maximum junction temperature, TA is the ambient temperature, and θJA is the junction-to-ambient thermal resistance of the specified package.
Note 4: In the test circuit, capacitors C1 and C2 are 3.3 µF, 0.3Ω maximum ESR capacitors. Capacitors with higher ESR will increase output resistance, reduce output voltage and efficiency. Note 5: Min. and Max. limits are guaranteed by design, test, or statistical analysis. Note 6: Typical numbers are not guaranteed but represent the most likely norm. Note 7: The minimum input high for the shutdown pin equals 40% of V+. Note 8: The maximum input low for the shutdown pin equals 20% of V+. Note 9: Specified output resistance includes internal switch resistance and capacitor ESR. See the details in the application information for simple negative voltage
converter. Note 10: The output switches operate at one half of the oscillator frequency, fOSC = 2fSW.
Page 3

Page 4

Page 5
Connection Diagrams
6-Lead Small Outline Package (M6)
10003122 Actual Size
10003104
Top View With Package Marking
Ordering Information
| Order Number | Package Number | Package Marking | Supplied as |
| LM2664M6 | MA06A | SO3A (Note 11) | Tape and Reel (1000 units/rail) |
| LM2664M6X | MA06A | SO3A (Note 11) | Tape and Reel (3000 units/rail) |
Note 11: The first letter "S" identifies the part as a switched capacitor converter. The next two numbers are the device number. The fourth letter "A" indicates the grade. Only one grade is available. Larger quantity reels are available upon request.
Pin Descriptions
| Pin | Name |
| 1 | GND |
| 2 | OUT |
| 3 | CAP− |
| 4 | SD |
| 5 | V+ |
| 6 | CAP+ |
Function
Power supply ground input. Negative voltage output. Connect this pin to the negative terminal of the charge-pump capacitor. Shutdown control pin, tie this pin to V+ in normal operation, and to GND for shutdown. Power supply positive voltage input. Connect this pin to the positive terminal of the charge-pump capacitor.
Circuit Description

The LM2664 contains four large CMOS switches which are switched in a sequence to invert the input supply voltage. Energy transfer and storage are provided by external capacitors. Figure 2 illustrates the voltage conversion scheme. When S1 and S3 are closed, C1 charges to the supply voltage V+. During this time interval, switches S2 and S4 are open. In the second time interval, S1 and S3 are open; at the same time, S2 and S4 are closed, C1 is charging C2. After a number of cycles, the voltage across C2 will be pumped to V+. Since the anode of C2 is connected to ground, the output at the cathode of C2 equals −(V+) when there is no load current. The output voltage drop when a load is added is
determined by the parasitic resistance (Rds(on) of the MOS- FET switches and the ESR of the capacitors) and the charge
FIGURE 2. Voltage Inverting Principle
transfer loss between capacitors. Details will be discussed in the following application information section.
Page 6
Application Information
SIMPLE NEGATIVE VOLTAGE CONVERTER
The main application of LM2664 is to generate a negative supply voltage. The voltage inverter circuit uses only two external capacitors as shown in the Basic Application Circuits. The range of the input supply voltage is 1.8V to 5.5V. The output characteristics of this circuit can be approximated by an ideal voltage source in series with a resistance. The voltage source equals −(V+). The output resistance Rout is a function of the ON resistance of the internal MOSFET switches, the oscillator frequency, the capacitance and ESR of C1 and C2. Since the switching current charging and discharging C1 is approximately twice as the output current, the effect of the ESR of the pumping capacitor C1 will be
multiplied by four in the output resistance. The output ca- pacitor C2 is charging and discharging at a current approximately equal to the output current, therefore, its ESR only counts once in the output resistance. A good approximation of Rout is:
where RSW is the sum of the ON resistance of the internal MOSFET switches shown in Figure 2. High capacitance, low ESR capacitors will reduce the output resistance. The peak-to-peak output voltage ripple is determined by the oscillator frequency, the capacitance and ESR of the output capacitor C2:
Again, using a low ESR capacitor will result in lower ripple.
SHUTDOWN MODE
A shutdown (SD ) pin is available to disable the device and reduce the quiescent current to 1µA. Applying a voltage less than 20% of V+ to the SD pin will bring the device into shutdown mode. While in normal operating mode, the pin is connected to V+.
CAPACITOR SELECTION
As discussed in the Simple Negative Voltage Converter section, the output resistance and ripple voltage are dependent on the capacitance and ESR values of the external capacitors. The output voltage drop is the load current times the output resistance, and the power efficiency is
Where IQ(V+) is the quiescent power loss of the IC device, and IL2Rout is the conversion loss associated with the switch on-resistance, the two external capacitors and their ESRs. The selection of capacitors is based on the specifications of the dropout voltage (which equals Iout Rout), the output voltage ripple, and the converter efficiency. Low ESR capacitors (Table 1) are recommended to maximize efficiency, reduce the output voltage drop and voltage ripple.
Low ESR Capacitor Manufacturers
| Manufacturer | Phone | Capacitor Type |
|---|---|---|
| Nichicon Corp. | (708)-843-7500 | PL & PF series, through-hole aluminum electrolytic |
| AVX Corp. | (803)-448-9411 | TPS series, surface-mount tantalum |
| Sprague | (207)-324-4140 | 593D, 594D, 595D series, surface-mount tantalum |
| Sanyo | (619)-661-6835 | OS-CON series, through-hole aluminum electrolytic |
| Murata | (800)-831-9172 | Ceramic chip capacitors |
| Taiyo Yuden | (800)-348-2496 | Ceramic chip capacitors |
| Tokin | (408)-432-8020 | Ceramic chip capacitors |
Page 7
Other Applications
PARALLELING DEVICES
Any number of LM2664s can be paralleled to reduce the output resistance. Each device must have its own pumping capacitor C1, while only one output capacitor Cout is needed as shown in Figure 3. The composite output resistance is:

FIGURE 3. Lowering Output Resistance by Paralleling Devices
CASCADING DEVICES
Cascading the LM2664s is an easy way to produce a greater negative voltage (e.g. A two-stage cascade circuit is shown in Figure 4). If n is the integer representing the number of devices cascaded, the unloaded output voltage Vout is (-nVin). The ef- fective output resistance is equal to the weighted sum of each individual device:
Rout = nRout_1 + n/2 Rout_2 + ... + Rout_n Note that, the number of n is practically limited since the increasing of n significantly reduces the efficiency, and in- creases the output resistance and output voltage ripple.

FIGURE 4. Increasing Output Voltage by Cascading Devices
COMBINED DOUBLER AND INVERTER
In Figure 5, the LM2664 is used to provide a positive voltage doubler and a negative voltage converter. Note that the total current drawn from the two outputs should not exceed 50 mA.
Page 8
Other Applications
(Continued)

FIGURE 5. Combined Voltage Doubler and Inverter
REGULATING VOUT
It is possible to regulate the negative output of the LM2664 by use of a low dropout regulator (such as LP2980). The whole converter is depicted in Figure 6. This converter can give a regulated output from −1.8V to −5.5V by choosing the proper resistor ratio:
Vout = Vref (1 + R1/R2) where, Vref = 1.23V
Note that, the following conditions must be satisfied simultaneously for worst case design:
Vin_min >Vout_min +Vdrop_max (LP2980)
+ Iout_max x Rout_max (LM2664)
Vin_max < Vout_max +Vdrop_min (LP2980)
+ Iout_min x Rout_min (LM2664)

FIGURE 6. Combining LM2664 with LP2980 to Make a Negative Adjustable Regulator
Page 9
Physical Dimensions
inches (millimeters) unless otherwise noted

6-Lead Small Outline Package (M6) NS Package Number MA06A
For Order Numbers, refer to the table in the "Ordering Information" section of this document.
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. For the most current product information visit us at www.national.com.
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user.
BANNED SUBSTANCE COMPLIANCE
- A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness.
National Semiconductor manufactures products and uses packing materials that meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ‘‘Banned Substances’’ as defined in CSP-9-111S2. Leadfree products are RoHS compliant.
National Semiconductor
National Semiconductor
Americas Customer
Europe Customer Support Center
Support Center
Fax: +49 (0) 180-530 85 86
Email: new.feedback@nsc.com
Email: europe.support@nsc.com
Tel: 1-800-272-9959
Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790
National Semiconductor
National Semiconductor
Asia Pacific Customer
Japan Customer Support Center
Support Center
Fax: 81-3-5639-7507
Email: ap.support@nsc.com
Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560