TSM23S-2RG overview
TSM23S-2RG is a component documented by Applied Motion Products. The PDF description identifies it as "Integrated Step-Servo Motor." This guide condenses the most useful engineering information from the available PDF so that designers and sourcing teams can identify the checks that still need confirmation in the original document.
Datasheet snapshot
- Manufacturer: Applied Motion Products...
- Part number: TSM23S-2RG
- Category: IC
- Datasheet length: 32 Pages
Key features noted in the PDF
- Programmable, Digital servo driver and motor in an integrated package
- Operates from a 12 to 70 volt DC power supply
- Control Modes: Torque Control * Analog input * SCL commanded Velocity Control * Digital input Control Velocity * Analog velocity * SCL Commanded Velocity (Jogging) Position Contro.
- Communications: RS-232 , RS-485 or Modbus/RTU
- 5000 line (20,000 counts/rev) encoder feedback
- Available torque: TSM23□-2□G: Up to 1.0 N•m Continuous(1.3 N•m Boost) TSM23□-3□G: Up to 1.5N•m Continuous(2.0 N•m Boost) TSM23□-4□G: Up to 1.5N•m Continuous(2.0 N•m Boost)
- I/O: 8 optically isolated digital inputs, with adjustable bandwidth digital noise rejection filter, 5 to 24 volts 4 optically isolated digital output, 30V/100 mA max. 1 analog inp.
Specifications and operating details
The following points were extracted from the PDF text. Check the associated conditions, notes and limits in the complete document before using a value in a design.
- Never use the drive where there is no airflow or where other devices cause the surrounding air to be more than 40°C (104°F).
- Absolute maximum power supply input is 75 VDC at which point an over-voltage alarm and fault will occur.
- RC880 Regen Clamp LEDs Green - Power Red - Regen on The maximum supply currents required by the TSM23S/Q are shown in the charts below at different power supply voltage inputs.
- The more the power supply voltage exceeds the motor voltage, the less current will be required from the power supply.
- GND TX +5V RX RS-485 communication allows connection of more than one drive to a single host PC, PLC, HMI or other computer.
- RX+ RX- TX+ TX- GND to PC GND to PC RX- to PC RX+ to PC TX- to PC TX+ Drive #1 Drive #2 Drive #N RX+ RX- TX+ TX- GND RX+ RX- TX+ TX- GND RX+ RX- TX+ TX- GND 120Ω RX+ RX- In a 2-wire system, the host must disable its transmitter before it c.
- to PC GND to PC TX- (A) to PC TX+ (B) Drive #1 Drive #2 Drive #N RX+ RX- TX+ TX- GND RX+ RX- TX+ TX- GND RX+ RX- TX+ TX- GND 120Ω RX+ RX- The TSM23S/Q has three types of inputs: High speed digital inputs for step & direction commands or en.
Topics covered by the datasheet
The document includes sections related to:
- Datasheet sections
Engineering review checklist
- Verify contact current, voltage, contact resistance, insulation and mating-cycle ratings.
- Check the exact keying, pitch, orientation, mating part and mechanical drawing before footprint approval.
- Review assembly force, retention, cable strain relief and environmental exposure for the application.
Always confirm values against the latest manufacturer-controlled datasheet, especially when qualifying a substitute or releasing a production BOM.
View the complete PDF and model record
Open the TSM23S-2RG datasheet and model details to review the complete PDF, document pages and available product information.
Source attribution
Adapted from the PDF associated with this DigiCamel model page.
Source model URL: https://www.digicamel.com/product.php?slug=tsm23s-2rg-applied-motion-products