LM358 overview
LM358 is a component documented by Texas Instruments. The PDF description identifies it as "Industry-Standard Dual Operational Amplifiers." This guide condenses the most useful engineering information from the available PDF so that designers and sourcing teams can identify the checks that still need confirmation in the original document.
Datasheet snapshot
- Manufacturer: Texas Instruments
- Part number: LM358
- Category: Amplifier
- Datasheet length: 47 Pages
Key features noted in the PDF
- Wide supply range of 3V to 36V (B, BA versions)
- Quiescent current: 300µA/ch (B, BA versions)
- Unity-gain bandwidth of 1.2MHz (B, BA versions)
- Common-mode input voltage range includes ground, enabling direct sensing near ground
- 2mV input offset voltage maximum at 25°C (BA version)
- 3mV input offset voltage maximum at 25°C (A, B versions)
- Internal RF and EMI filter (B, BA versions)
Applications listed in the PDF
- Merchant network and server power supply units
- Multi-function printers
- Power supplies and mobile chargers
- Motor control: AC induction, brushed DC, brushless DC, high-voltage, low-voltage, permanent magnet, and stepper motor
- Desktop PC and motherboard
- Indoor and outdoor air conditioners
Specifications and operating details
The following points were extracted from the PDF text. Check the associated conditions, notes and limits in the complete document before using a value in a design.
- Manufacturer or author: Texas Instruments, Incorporated [SLOS068,A] PDF pages: 68 Industry-Standard Dual Operational Amplifiers Wide supply range of 3V to 36V (B, BA versions) Quiescent current: 300µA/ch (B, BA versions) Unity-gain bandwid.
- The LM358B and LM2904B op amps simplify circuit design with enhanced features such as unity-gain stability, lower offset voltage maximum of 3mV (2mV maximum for LM358BA and LM2904BA), and lower quiescent current of 300µA per amplifier (typ.
- These are stress ratings only, and do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions.
- LM358B, LM358BA, LM2904B, AND LM2904BA V(ESD) Electrostatic discharge Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001(1) ±2000 V Charged-device model (CDM), per JEDEC specification JESD22-C101(2) ±1500 LM158, LM258, LM358, LM158, LM258A.
- Maximum VS for testing purposes is 30 V for LM358 and LM358A. (2) All typical values are TA = 25°C.
- Maximum VS for testing purposes is 26 V for LM2904 and 32 V for LM2904V. (2) All typical values are TA = 25°C.
- Maximum VS for testing purposes is 30 V for LM158 and LM158A. (2) All typical values are TA = 25°C. (3) On products compliant to MIL-PRF-38535, this parameter is not production tested.
Topics covered by the datasheet
The document includes sections related to:
- Industry-Standard Dual Operational Amplifiers datasheet (Rev. AB)
- Package Information
Engineering review checklist
- Verify supply range, input common-mode range and output swing at the required load.
- Check offset, bias current, noise, bandwidth, slew rate and stability for the intended feedback network.
- Review supply decoupling, source impedance, capacitive-load behavior and thermal limits in the final layout.
Always confirm values against the latest manufacturer-controlled datasheet, especially when qualifying a substitute or releasing a production BOM.
View the complete PDF and model record
Open the LM358 datasheet and model details to review the complete PDF, document pages and available product information.
Source attribution
Adapted from the PDF associated with this DigiCamel model page.
Source model URL: https://www.digicamel.com/product.php?slug=lm358-texas-instruments