Y1112 POINN | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 4

Technical content

THE FLUORACTOR® Y1112 FLUORESCENT LAMP STARTER SWITCH PRODUCT INFORMATION JUNE 1984 - REVISED SEPTEMBER 1997Copyright © 1997, Power Innovations Limited, UK Information is current as of publication date. Products conform to specifications in accordance with the terms of Power Innovations standard warranty. Production processing does not necessarily include testing of all parameters.

  • V(BR) 1200 to 1500 V
  • IH > 175 mA
  • IG T < 2 mA descriptio n This product is intended for use as a T8/T12 fluorescent tube starter switch on 200-240 V a.c. supplies with tube sizes up to 5ft with leading and lagging ballast circuits. K A G TO-220 PACKAGE (TOP VIEW) Pin 2 is in electrical contact with the mounting base. MDC1ACA absolute maximum ratings at 25°C case temperature (unless otherwise noted) RATIN G SYMBO L VALU E UNIT Crest working off-state voltage (Full wave rectified 50 Hz a.c.) VDW M 375 V Peak reverse gate voltage VRG M 6 V On-state current — continuous — repetitive peak — non-repetitive peak I T ITRM ITS M 1.5 A Peak gate current IGR M 0.5 A Average gate power PG(av) 0.3 W Operating case temperature range TC -5 to +85 °C Storage temperature range Tstg -10 to +110 °C Lead temperature during soldering 1.6 mm from the case for 10 seconds Tlead 230 °C electrical characteristics at 25°C case temperature (unless otherwise noted) PARAMETE R TEST CONDITION S MIN TY P MA X UNIT ID Off-state current VD = VDW M Tj = 65°C 1 m A VT On-state voltage IT = 2 A 3.1 V V (BR) Clamping voltage IBR = 5 mA tp < 200 µs, 2% duty cycle 1200 1500 V IH Holding current See application circuit 175 m A IGT M Peak gate trigger current VAA = 10 V R L = 10 Ω 2 m A VGT M Peak gate trigger voltage VAA = 10 V R L = 10 Ω 3 V thermal characteristics PARAMETE R MIN TY P MA X UNIT R θJA Junction to free air thermal resistance 62.5 °C/W R θJC Junction to case thermal resistance 3.5 °C/W

ends and ultimately required tube replacement. electromechanical canisters. Figure 1. Two terminal starter circui t

JUNE 1984 - REVISED SEPTEMBER 1997 THE FLUORACTOR® Y1112 FLUORESCENT LAMP STARTER SWITCH PRODUCT INFORMATION TO-220 3-pin plastic flange-mount packag e This single-in-line package consists of a circuit mounted on a lead frame and encapsulated within a plastic compound. The compound will withstand soldering temperature with no deformation, and circuit performance characteristics will remain stable when operated in high humidity conditions. Leads require no additional cleaning or processing when used in soldered assembly. MECHANICAL DAT A TO220 ALL LINEAR DIMENSIONS IN MILLIMETERS ø 1,23 1,32 4,20 4,70 1 2 3 0,97 0,61 see Note C see Note B 10,0 10,4 2,54 2,95 6,0 6,6 14,55 15,90 12,7 14,1 3,5 6,1 1,07 1,70 2,34 2,74 4,88 5,28 3,71 3,96 0,41 0,64 2,40 2,90 VERSION 2 VERSION 1 NOTES: A. The centre pin is in electrical contact with the mounting tab. B. Mounting tab corner profile according to package version. C. Typical fixing hole centre stand off height according to package version. Version 1, 18.0 mm. Version 2, 17.6 mm. MDXXBE

THE FLUORACTOR® Y1112 FLUORESCENT LAMP STARTER SWITCH JUNE 1984 - REVISED SEPTEMBER 199 7 PRODUCT INFORMATION IMPORTANT NOTIC E Power Innovations Limited (PI) reserves the right to make changes to its products or to discontinue any semiconductor product or service without notice, and advises its customers to verify, before placing orders, that the information being relied on is current. PI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with PI's standard warranty. Testing and other quality control techniques are utilized to the extent PI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except as mandated by government requirements. PI accepts no liability for applications assistance, customer product design, software performance, or infringement of patents or services described herein. Nor is any license, either express or implied, granted under any patent right, copyright, design right, or other intellectual property right of PI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. PI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, INTENDED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT APPLICATIONS, DEVICES OR SYSTEMS . Copyright © 1997, Power Innovations Limited