XPD-MR-08-47CDA

XPD-MR-08-15CDA SOURCE | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 6

Technical content

Features

• XFP MSA Rev 4.5 compliant
• Available in all 100GHz C-Band Wavelengths on the DWDM ITU Grid
• 80km Reach
• Cooled EML with isolator
• APD Receiver
• Power dissipation <3.5W
• -5 to 70 C temperature range
• Cold Start Up Wavelength Compliance
• Digital Diagnostics
• XFI High Speed Electrical Interface
• RoHS Compliant
• Class 1 Laser, 21CFR 1040.10/1040.11
• EN 60825-1/A1:2002 Compliant
• Bail Latch Color: WHITE Parameter Symbol Min Typical Max Unit Supply Voltage (1.8V) Vcc2 1.71 1.8 1.89 V Supply Voltage (3.3V) Vcc3 3.14 3.3 3.47 V Supply Voltage (5V) Vcc5 4.75 5 5.25 V Total Current on any pin ICC - - 500 mA Inrush Current (1.8V) Iinrush2 - - 1 A Inrush Current (3.3V) Iinrush3 - - 0.75 A Inrush Current (5V) Iinrush5 - - 0.5 A Module current ramp rate - - 100 mA/µS Power on 1.8V rail P2rail - - 1.8 W Power on 3.3V rail P3rail - - 2.5 W Power on 5V rail P5rail - - 2.5 W Module Total Power consumption Pt - - 3.5 W Power Consumption-P_Down mode Pp_d - - 1.5 W Power Supply Noise Rejection PSNR Compliant to Section 2.7.2 of XFP MSA Bit Rate BR 9.95 - 11.1 Gb/s Operating Temperature (case) Top -5 - 70 ºC Strorage Temperature Tst -40 - 85 ºC General Operations Parameter Symbol Min Typical Max Unit Maximum Supply Voltage (3.3V) Vcc3 -0.3 - 3.6 V Maximum Supply Voltage (5.0V) Vcc5 -0.3 - 5.5 V Maximum Supply Voltage (1.8V) Vcc2 -0.3 - 2 V Storage Temperature Tst -40 - 85 ºC Absolute Maximum Rating a) Peak to peak noise when measured with a 1 MHz low pass filter b) Peak to peak noise when measured with 1MHz-10MHz low pass filter

10 Gbps 80km DWDM Multirate XFP Transceiver

Rev. 0.9 Parameter Symbol Min Typical Max Unit Output Power PO 0 2 4 dBm Average Launch Power Tx_Off Poff - - -30 nm Extinction Ratio ER 9 - - dB Eye Mask ITU-T G.691, Telcordia GR-253-CORE, IEEE802.3 10GBASE-ZR Compliant Side Mode Suppression Ratio SMSR 30 - - dB Center Wavelength λ ITU Grid nm Channel Spacing ∆f - 100 - GHz Spectral Width ∆λ20 - - 1 nm Jitter Generation (peak-to-peak) Jgen(pk-pk) - - 0.1 UI Jitter Generation (RMS) Jgen(RMS) - - 0.01 UI Dispersion Penalty at 1600 ps/nm DP - - 2 dB Relative Intensity Noise RIN - - -130 dB/Hz Reflectance Tolerance ref T - - -27 dB Transmitter Specifications (Optical) Parameter Symbol Min Typical Max Unit Sensitivity (9.95Gb/s)a Rx sens995 - - -24 dBm Sensitivity (10.7Gb/s)a Rx sens1070 - - -23 dBm Overloada Rx OL -7 - - dBm Wavelengthb λ 1528 - 1561 nm Optical Return Loss ORL - - -27 dB LOS Assert - -34 - - dBm LOS De-assert - - - -24 dBm LOS Hysteresis - 0.5 - - dB Receiver Specifications (Optical) a) At 9dB ER, 1E-12 BER, 231-1 PRBS, back to back b) Operational over 1200 - 1625nm range Parameter Symbol Min Typical Max Unit Input Differential Impedence Rin - 100 - Ω Differential Data Input Swing Vin,p-p 120 - 820 mV TxDisable_Disable Vd 2 - Vcc3 V TxDisable_Enable Ven GND - GND + 0.8 V Transmitter Specifications (Electrical) Parameter Symbol Min Typical Max Unit Reference Differential Output Impedence Zd - 100 - Ω Differential Data Output Swing Vout,p-p 340 - 850 mV Output Rise Time, 20-80% tr 24 - - ps Output Fall Time, 20-80% tf 24 - - ps LOS Fault VLOS_fault host_Vcc3 - 0.5 - host_Vcc3 V LOS Normal VLOS_normal GND - GND + 0.4 V Receiver Specificatioins (Elelctrical)

Rev. 0.9 Parameter Symbol Min Typical Max Unit Clock Differential Input Impedance Zd 80 100 120 Ω Differential Input Clock Amplitude (p-p) 640 - 1600 mV Reference Clock Duty Cycle 40 - 60 % Reference Clcok Rise/Fall Time (20%-80%) Tr/Tf 200 - 1250 ps Reference Clock Frequency f0 - Baud/64 - MHz Reference Clock λ Wavelength Ordering XPD-MR-08-xxCDA See table below for “xx” values ITU Channel/Product Code Frequency (THz) Wavelength (nm) ITU Channel/Product Code Frequency (THz) Wavelength (nm) 17 191.7 1563.863 40 194.0 1545.322 18 191.8 1563.047 41 194.1 1544.526 19 191.9 1562.233 42 194.2 1543.730 20 192.0 1561.419 43 194.3 1542.936 21 192.1 1560.606 44 194.4 1542.142 22 192.2 1559.794 45 194.5 1541.349 23 192.3 1558.983 46 194.6 1540.557 24 192.4 1558.173 47 194.7 1539.766 25 192.5 1557.363 48 194.8 1538.976 26 192.6 1556.555 49 194.9 1538.186 27 192.7 1555.747 50 195.0 1537.397 28 192.8 1554.940 51 195.1 1536.609 29 192.9 1554.134 52 195.2 1535.822 30 193.0 1553.329 53 195.3 1535.036 31 193.1 1552.524 54 195.4 1534.250 32 193.2 1551.721 55 195.5 1533.465 33 193.3 1550.918 56 195.6 1532.681 34 193.4 1550.116 57 195.7 1531.898 35 193.5 1549.315 58 195.8 1531.116 36 193.6 1548.515 59 195.9 1530.334 37 193.7 1547.715 60 196.0 1529.553 38 193.8 1546.917 61 196.1 1528.773 39 193.9 1546.119 λc Wavelength Guide

Rev. 0.9 Pin Logic Symbol Name/Description Note

1 GND Module Ground 1

2 VEE5 Optional -5.2V Power Supply (not used)

3 LVTTL-I Mod_DeSel Module De-select; When held low allows module to respond to 2-wire interface

4 LVTTL-O Interrupt Interrupt; Indicates presence of an important condition which can be read over the 2-wire serial interface 2

5 LVTTL-I TX_DIS Transmitter Disable; Turns off transmitter laser output

6 Vcc5 +5V Power Supply

7 GND Module Ground 1

8 Vcc3 +3.3V Power Supply 9 Vcc3 +3.3V Power Supply

10 LVTTL-I/O SCL 2-Wire Serial Interface Clock 2

11 LVTTL-I/O SDA 2-Wire Serial Interface Data Line 2

12 LVTTL-O Mod_Abs Indicates Module is not present. Grounded in the Module 2

13 LVTTL-O Mod_NR Module Not Ready; Indicating Module Operational Fault 2

14 LVTTL-O RX_LOS Receiver Loss Of Signal Indicator 2

15 GND Module Ground 1

16 GND Module Ground 1

17 CML-O RD- Receiver Inverted Data Output

18 CML-O RD+ Receiver Non-Inverted Data Output

19 GND Module Ground 1

20 Vcc2 +1.8V Power Supply

21 LVTTL-I P_Down/RST

Power Down; When high, requires the module to limit power consumption to 1.5W or below. 2-Wire serial interface must be functional in the low power mode. Reset; The falling edge initiates a complete reset of the module including the 2-wire serial interface, equivalent to a power cycle. 22 Vcc2 +1.8V Power Supply

23 GND Module Ground 1

24 PECL-I RefCLK+ Reference Clock Non-Inverted Input, AC coupled on the host board

25 PECL-I RefCLK- Reference Clock Inverted Input, AC coupled on the host board

26 GND Module Ground 1

27 GND Module Ground 1

28 CML-I TD- Transmitter Inverted Data Input

29 CML-I TD+ Transmitter Non-Inverted Data Input

30 GND Module Ground 1

Pin Out Definition Notes: 1. Module ground pins GND are isolated from the module case and chassis ground within the module.

Rev. 0.9 Pinout Diagram Host PCBXFP Pinout TopView TOWARD ASIC TOWARD BEZEL GND MOD_DESEL INTERR UPT TX_DIS VEE5 VCC5 GND VCC3 VCC3 SCL SDA MOD_ABS MOD_NR RX_LOS GND GND TD+ TD- GND GND REFCLK- REFCLK+ GND VCC2 P_DOWN/RST VCC2 GND RD+ RD- GND Mechanical Drawing .451 11.47 .150 3.80 .237 6.02 .246 6.25 .720 18.29 .272 6.91 .636 16.15 DIMENSIONS DEFINED BY XFP MULTISOURCING AGREEMENT (MSA). NOTES: UNLESS OTHERWISE SPECIFIED LUMINENOIC'S XFP TRANSCEIVERS ARE COMPLIANT WITH THE 1. .480 12.19 2.720 69.09 .332 8.44 77.98 3.070 .352 8.95 ISO VIEW

Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static free environment is highly recommended. Follow guidelines according to proper ESD procedures. Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or indirect radiation. XPD-MR-08-xxCDA IMPORTANT NOTICE! All information contained in this document is subject to change without notice, at LuminentOIC’s sole and absolute discretion. LuminentOIC warrants performance of its products to current specifi cations only in accordance with the company’s standard one-year warranty; however, specifi cations designated as “preliminary” are given to describe components only, and LuminentOIC expressly disclaims any and all warranties for said products, including express, implied, and statutory warran- ties, warranties of merchantability, fi tness for a particular purpose, and non-infringement of proprietary rights. Please refer to the company’s Terms and Conditions of Sale for further warranty information. LuminentOIC assumes no liability for applications assistance, customer product design, software performance, or infringement of patents, services, or intellectual property described herein. No license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and LuminentOIC makes no representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual property rights. Products described in this docu- ment are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. LuminentOIC customers using or selling products for use in such applications do so at their own risk and agree to fully defend and indemnify LuminentOIC for any damages resulting from such use or sale. THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN “AS IS” BASIS. Customer agrees that LuminentOIC is not liable for any actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. Customer must contact LuminentOIC to obtain the latest version of this publication to verify, before placing any order, that the information contained herein is current. © LuminentOIC, Inc. 2003 All rights reserved LUMINENTOIC.COM LUMNDS420-NOV1106 Rev. 0.9 Warnings Legal Notice

Ordering Information

Part Numbering Defi nition: X P D - M R - Reach - ITU Channel Temperature Diagnostic Revision XPD = DWDM XFP MR = Multi-Rate PD = DWDM XFP xx = 15 to 61 C = Commerical Temp (-5 to 70C) D = Digital Diagnostic 08 = 80km A = Design Revision