XP95-DM GAMEWELL-FCI | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 2
Technical content
Features
- Compatible with all the Gamewell-FCI analog addressable 600 Series fire alarm control panels
- Combines photoelectric smoke and thermal sensor values for enhanced detector performance
- Five programmable detection modes
- Detector head uses common analog addressable style bases
- Address is set by X-Pert Programming Card stored in sensor base
- Rate-of-rise heat detection
- Drift compensation in Modes 1 through 4 CS-2403ph1.wmf XP95-DM An ISO 9000-2000 Company SIGNALING
12 Clintonville Road, Northford, CT 06472-1610 USA • Tel: (203) 484-7161 • Fax: (203) 484-7118
CS-2403 Rev. a1 page 2 of 2 www.gamewell-fci.com Heat Detector Response ModesOperation (Continued) The XP95-DM monitors temperature using a single ther- mistor which provides a voltage output proportional to the external air temperature. The thermistor is calibrated to the normal analog value at a temperature of 25°C (77°F). Values from each sensing ele- ment are processed by on-board electronics according to detector programming. The XP95-DM Discovery multi-sen- sor detector is automatically programmed for pure heat detection, pure smoke detection, or a combination of both. Programming Assigning an XP95-DM detector to a verification zone allows local operation when smoke is detected by the optical element located in the head, and general alarm operation when heat is present. When smoke is sensed, the local sounder, relay, or LED located in the detector base (or group of bases) will be activated, and a pre-alarm signal will be sent back to the panel. The Aux (4th) relay on the common control card will transfer. If heat is also present, the panel will go into a full General Alarm condi- tion. If there is only smoke, the panel will automatically restore when the smoke clears. Alarm and trouble conditions are determined by the elec- tronics in the detector head, which also automatically per- forms drift compensation. Norma l sensitivity is 2.4% per foot. When the sensor is in alarm, the LEDs in the sensor’s housing will light continuously. The XP95-DM is connected to a two-wire signal line circuit (SLC) carrying both XP95 protocol data and a 17 to 28 VDC supply voltage. The XP95-DM is insensitive to loop polarity. A remote LED indicator may be connected. Engineer’s Specifications The contractor shall furnish and install, where indicated on the plans, a combination phot o/heat multi-sensor detector (Gamewell-FCI model XP95-DM) with one of the several Addressable Mounting Base Options available. The combi- nation sensor head and twist-lock mounting base shall be UL Listed and UL-Listed as compatible with the Gamewell- FCI Fire Alarm Control Panels. The base shall permit free interchange of sensor heads without requiring any addi- tional wiring or additional programming of the head or base. The smoke sensor shall contain an integral LED that shall illuminate when the unit goes into alarm. MODE TYPICAL Application Temperature MAXIMUM Application Temperature MINIMUM Static Response Temperature TYPICAL Static Response Temperature MAXIMUM Static Response Temperature For air temperatures in the range of 59° F to 131° F (15° C to 55° C) the analog value for a detector in Mode 1 will correspond approximately to the air temperature. Specifications Standby Current: 500 µA average, 750 µA peak Alarm LED Current: 0.004 A Remote Alarm Output: 0.004 A @ 5 VDC Minimum Operating Temperature: –5°F (–20.55°C) Maximum Operating Temperature: See table on page 2 Relative Humidity (non-condensing): 0% to 95%
Ordering Information
XP95-DM Discovery Multi-Sensor, analog addressable, photoelectric and thermal (58000-750). XP95-B6EZ 6" (15.24 cm) ultra-low-profile EZ-Fit mounting base with X-Pert programming card (45681-250). XP95-B4 4" (10.16 cm) mounting base with X-Pert programming card (45681-210). XP95-B6R4 6" (15.24 cm) relay base (four-wire) with X-Pert programming card. XP95-B6SNDR 6" (15.24 cm) mounting base with X-Pert programming card and audible alarm sounder.
71112 Additional blank X-Pert programming
cards. 30203 Remote LED (24 V).