TMS320F28P550SJ_V02 TI | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 268
Technical content
TMS320F28P55x Real-Time Microcontrollers
1 Features
- Real-time processing: – 150MHz C28x 32-bit DSP CPU – Equivalent to 300MHz Arm® Cortex®-M7 based device on real-time signal chain performance (see the Real-time Benchmarks Showcasing C2000™ Control MCU's Optimized Signal Chain Application Note – IEEE 754 single-precision Floating-Point Unit (FPU32) – Trigonometric Math Unit (TMU)
- Support for Nonlinear Proportional Integral Derivative (NLPID) control – Neural-Network Processing Unit (NNPU) – CRC Engine and Instructions (VCRC)
- Programmable Control Law Accelerator (CLA) – 150MHz – Equivalent to 200MHz Arm® Cortex®-M7 based device on real-time signal chain performance (see the Real-time Benchmarks Showcasing C2000™ Control MCU's Optimized Signal Chain Application Note – IEEE 754 single-precision floating-point instructions – Executes code independently of main CPU
- On-chip memory – 1088KB of flash (ECC-protected) across five independent banks
- Four 256KB banks
- One 64KB bank, ideal of LFU/Bootloaders/ data – 8KB of OTP (One Time Programmable flash memory) – 133KB of RAM (ECC/Parity protected)
- Security – Secure Boot – JTAG Lock – Advanced Encryption Standard (AES) accelerator – Unique Identification (UID) number
- Clock and system control – Two internal 10MHz oscillators – Crystal oscillator or external clock input – Windowed watchdog timer module – Missing clock detection circuitry – Dual-clock Comparator (DCC)
- 3.3V I/O design – Internal VREG generation allows for single- supply design – Brownout reset (BOR) circuit – 5V failsafe and tolerant capability on 4 GPIOs for PMBUS/I2C support – Configurable 1.35V VIH on 4 GPIOs
- System peripherals – 6-channel Direct Memory Access (DMA) controller – 91 individually programmable multiplexed General-Purpose Input/Output (GPIO) pins (22 shared with Analog) – 17 digital inputs on analog pins – Enhanced Peripheral Interrupt Expansion (ePIE) – Multiple low-power mode (LPM) support
- Communications peripherals – One Power-Management Bus (PMBus) interface
- Fast Plus Mode Support - 1MHz SCL
- 5V/3.3V/1.35V VIH support on select pins – Two Inter-integrated Circuit (I2C) interfaces – Two Controller Area Network with Flexible Data-Rate (CAN FD/MCAN) bus port
- 4KB message RAM per MCAN module, independent of system memory
- Ability to re-use RAM for CPU data variables if MCAN is not used – One Universal Serial Bus (USB 2.0 MAC + PHY) – Two Serial Peripheral Interface (SPI) ports – Three UART-compatible Serial Communication Interface (SCI) – One UART-compatible Local Interconnect Network (LIN) interface
- Analog system – Five 3.9MSPS, 12-bit Analog-to-Digital Converters (ADCs)
- Up to 39 external channels (includes one gpdac output)
- Four integrated Post-Processing Blocks (PPB) per ADC – Four windowed comparators (CMPSS) with 12-bit reference Digital-to-Analog Converters (DACs)
- Digital glitch filters
- Low DAC output to pin capability on CMPSS1 – One 12-bit buffered DAC output – Three Programmable Gain Amplifiers (PGAs)
- Unity gain support
- Inverting and non-inverting gain mode support
- Programmable output filtering ADVANCE INFORMATION TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications, intellectual property matters and other important disclaimers. ADVANCE INFORMATION for preproduction products; subject to change without notice.
- Enhanced control peripherals – 24 ePWM channels with 16 channels that have high-resolution capability (150ps resolution)
- Integrated dead-band support
- Integrated hardware trip zones (TZs) – Two Enhanced Capture (eCAP) modules – Three Enhanced Quadrature Encoder Pulse (eQEP) modules with support for CW/CCW operation modes – Embedded Pattern Generator (EPG)
- Configurable Logic Block (CLB) – 2 tiles – Augments existing peripheral capability – Supports position manager solutions
- Live Firmware Update (LFU)
- Diagnostic features – Memory Power-On Self-Test (MPOST)
- Functional Safety-Compliant targeted – Developed for functional safety applications – Documentation available to aid ISO 26262 and IEC 61508 system design – Systematic capability up to ASIL D and SIL 3 targeted – Hardware integrity up to ASIL B targeted
- Safety-related certification – ISO 26262 certification up to ASIL B by TÜV SÜD planned
- Package options: – 128-pin Thin Quad Flatpack (TQFP) [PDT suffix] – 100-pin Low-profile Quad Flatpack (LQFP) [PZ suffix] – 80-pin TQFP [PNA suffix] – 64-pin LQFP [PM suffix] – 56-pin Very Thin Quad Flatpack No-Lead (VQFN) [RSH suffix]
- Temperature options: – Junction (TJ): –40°C to 150°C
2 Applications
- Appliances – Air conditioner outdoor unit
- Building automation – Door operator drive control
- Industrial machine & machine tools – Automated sorting equipment – Textile machine
- AC inverter & VF drives – AC drive control module – AC drive position feedback – AC drive power stage module
- Linear motor transport systems – Linear motor power stage
- Single & multi axis servo drives – Servo drive position feedback – Servo drive power stage module
- Speed controlled BLDC drives – AC-input BLDC motor drive – DC-input BLDC motor drive
- Factory automation – Robot servo drive – Mobile robot motor control – Position sensor
- Industrial power – Industrial AC-DC
- UPS – Three-phase UPS – Single-phase online UPS
- Telecom & server power – Merchant DC/DC – Merchant network & server PSU – Merchant telecom rectifiers
- Hybrids, electric & powertrain systems – DC/DC converter – Inverter & motor control – On-board (OBC) & wireless charger – Virtual engine sound system (VESS) – Engine fan – eTurbo/charger – Pump – Electric power steering (EPS)
- Infotainment and cluster – Head-up display – Automotive head unit – Automotive external amplifier
- Body electronics & lighting – Automotive HVAC compressor module – DC/AC inverter – Headlight
- ADAS – Mechanically scanning LIDAR
- EV charging infrastructure – AC charging (pile) station – DC charging (pile) station – EV charging station power module – Wireless EV charging station
- Renewable energy storage – Energy storage power conversion system (PCS) – Portable Power Station TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
2 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
- Solar energy – Central inverter – Micro inverter – Solar power optimizer – Solar arc protection – Rapid shutdown – String inverter
3 Description
The TMS320F28P55x (F28P55x) is a member of the C2000™ real-time microcontroller family of scalable, ultra-low latency devices designed for efficiency in power electronics, including but not limited to: high power density, high switching frequencies, and supporting the use of GaN and SiC technologies. These include such applications as:
- Motor drives
- Appliances
- Hybrid, electric & powertrain systems
- Solar & EV charging
- Digital power
- Body electronics & lighting
- Test & measurement The real-time control subsystem is based on TI’s 32-bit C28x DSP core, which provides 150MHz of signal- processing performance for floating- or fixed-point code running from either on-chip flash or SRAM. The C28x CPU is further boosted by the Floating-Point Unit (FPU) , Trigonometric Math Unit (TMU) , and VCRC (Cyclical Redundancy Check) extended instruction sets, speeding up common algorithms key to real-time control systems. The CLA allows significant offloading of common tasks from the main C28x CPU. The CLA is an independent 32-bit floating-point math accelerator that executes in parallel with the CPU. Additionally, the CLA has its own dedicated memory resources and it can directly access the key peripherals that are required in a typical control system. Support of a subset of ANSI C is standard, as are key features like hardware breakpoints and hardware task-switching. The F28P55x supports up to 1088KB of flash memory divided into four 256KB banks plus one 64KB bank, which enable programming one bank and execution in another bank in parallel. Up to 133KB of on-chip SRAM is also available to supplement the flash memory. The Live Firmware Update hardware enhancements on F28P55x allow fast context switching from the old firmware to the new firmware to minimize application downtime when updating the device firmware. High-performance analog blocks are integrated on the F28P55x real-time microcontroller (MCU) and are closely coupled with the processing and PWM units to provide optimal real-time signal chain performance. Twenty-four PWM channels, all supporting frequency-independent resolution modes, enable control of various power stages from a 3-phase inverter to power factor correction and advanced multilevel power topologies. The inclusion of the Configurable Logic Block (CLB) allows the user to add custom logic and potentially integrate FPGA-like functions into the C2000 real-time MCU. Interfacing is supported through various industry-standard communication ports (such as SPI, SCI, I2C, PMBus, LIN, and CAN FD) and offers multiple pin-muxing options for optimal signal placement. Want to learn more about features that make C2000 Real-Time MCUs the right choice for your real-time control system? Check out The Essential Guide for Developing With C2000 ™ Real-Time Microcontrollers and visit the C2000™ real-time control MCUs page. The Getting Started With C2000 ™ Real-Time Control Microcontrollers (MCUs) Getting Started Guide covers all aspects of development with C2000 devices from hardware to support resources. In addition to key reference documents, each section provides relevant links and resources to further expand on the information covered. Ready to get started? Check out the TMDSCNCD28P55X evaluation board or the LAUNCHXL-F28P55X development kit, and download C2000Ware. www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 3 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Package Information
PART NUMBER(1) PACKAGE(2) PACKAGE SIZE(3) TMS320F28P559SJ-Q1 PDT (QFP, 128) 16mm x 16mm PZ (QFP, 100) 16mm x 16mm PNA (QFP, 80) 12mm x 12mm PM (QFP, 64) 12mm x 12mm TMS320F28P550SJ PDT (QFP, 128) 16mm x 16mm PZ (QFP, 100) 16mm x 16mm PNA (QFP, 80) 12mm x 12mm PM (QFP, 64) 12mm x 12mm RSH (VQFN, 56) 7mm x 7mm TMS320F28P559SG-Q1 PDT (QFP, 128) 16mm x 16mm PZ (QFP, 100) 16mm x 16mm PNA (QFP, 80) 12mm x 12mm PM (QFP, 64) 12mm x 12mm TMS320F28P550SG PDT (QFP, 128) 16mm x 16mm PZ (QFP, 100) 16mm x 16mm PNA (QFP, 80) 12mm x 12mm PM (QFP, 64) 12mm x 12mm RSH (VQFN, 56) 7mm x 7mm TMS320F28P550SD PZ (QFP, 100) 16mm x 16mm PNA (QFP, 80) 12mm x 12mm PM (QFP, 64) 12mm x 12mm RSH (VQFN, 56) 7mm x 7mm (1) For more information on these devices, see the Device Comparison table. (2) For more information, see the Mechanical, Packaging and Orderable Information section. (3) Package size (length x width) is a nominal value and includes pins, where applicable TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
4 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
3.1 Functional Block Diagram
(150 MHz) FPU32 TMU VCRC DIAGNOSTICS DCC MPOST ERAD JTAG/cJTAG M0-M1 RAM 4KB LS0-LS9 RAM 64KB GS0-GS3 RAM 64KB DMA
6 Channels
(150 MHz) PF1 24x ePWM Channels (16Ch Hi-Res Capable) 2x eCAP 3x eQEP (CW/CCW Support) 4x CMPSS 1x Buffered DAC PF3 65x GPIO Data Input XBAR Output XBAR ePWM XBAR PF4 PF2 CLA to DMA MSG RAM DMA to CLA MSG RAM SYSTEM CONTROL CPU Timers XTAL INTOSC1, INTOSC2 PLL ePIE Windowed WD NMI WD SECURITY JTAG Lock Secure Boot CLB XBAR CLB Input XBAR CLB Output XBAR PF7 OTHERS EPG CPU CLA DMA Buses Legend 3x PGA PF8 3x SCI 2x I2C PF9 PF10 PF11 1x AES PF12 Boot ROM Secure ROM Flash Bank0
128 Sectors, 256KB
32 Sectors, 64 KB
2x CAN FD 1x LIN 2x CLB LFU1x USB Secure Memories Shown in Red NNPU NNPU NNPU A. The internal DAC from one of the CMPSS modules can be configured as an output DAC. B. The LIN module can also be used as a SCI module. Figure 3-1. Functional Block Diagram www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 5 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.7 Thermal Resistance Characteristics for PDT
6.8 Thermal Resistance Characteristics for PZ
6.9 Thermal Resistance Characteristics for PNA
6.10 Thermal Resistance Characteristics for PM
6.11 Thermal Resistance Characteristics for RSH
7.8 Embedded Real-Time Analysis and Diagnostic
11 Mechanical, Packaging, and Orderable
TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
6 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
4 Device Comparison
Table 4-1. Device Comparison FEATURE(1) (4) F28P559SJ-Q1(3) F28P550SJ F28P559SG-Q1(3) F28P550SG F28P550SD C28x Subsystem Frequency (MHz) 150 C28x 32-bit Floating-Point Unit (FPU) Yes VCRC Yes TMU - Type 1 Yes - Type 1 - NLPID Instruction Supported CLA - Type 2 Number 1: F28P559SJ9- Q1, F28P559SJ6- 0: F28P559SJ2- 1: F28P559SG9- Q1,F28P559SG8- 0: F28P559SG2- Frequency (MHz) 150 6-Channel DMA - Type 0 1 External Interrupts 5 MIPS 300 (CPU + CLA) Memory Flash Main Array 1MB (4 x 256KB Banks) 512KB (2 x 256KB Banks) 256KB (2 x 128KB Banks) 64KB Bank F28P559SJ9-Q1, F28P550SJ9, F28P559SJ6-Q1, F28P550SJ6, F28P559SG9-Q1, F28P550SG9 - User OTP 8KB 2KB RAM Dedicated 4KB Local Shared RAM 64KB 32KB Message 1KB Global Shared RAM 64KB 32KB Total RAM 133KB 101KB 69KB Message RAM Types C28x CPUs and CLAs 512 bytes (256 bytes per direction) DMAs and CLAs 512 bytes (256 bytes per direction) ECC FLASH, Mx RAM Parity ROM, CAN RAM, Message RAM, LSx RAM, GSx RAM System Configurable Logic Block (CLB) 2 tiles - F28P559SJ9-Q1, F28P559SJ6-Q1, F28P550SJ9, F28P550SJ6, F28P559SG9-Q1, F28P550SG9, F28P559SG8-Q1, F28P550SG8, F28P550SD7 Neural-Network Processing Unit (NNPU) 1 - F28P559SJ9-Q1, F28P550SJ9, F28P559SG9-Q1, F28P550SG9 - Embedded Pattern Generator (EPG) 1 32-bit CPU Timers 3 Advanced Encryption Standard (AES) Accelerator 1 Live Firmware Update (LFU) Support Yes, with enhancements and flash bank erase time improvements Security for on-chip flash and RAM Yes Zero-pin Boot Yes Secure Boot Yes JTAG Lock Yes MPOST Yes Embedded Real-time Analysis and Diagnostic (ERAD) - Type 2 1 Non-maskable Interrupt Watchdog (NMIWD) timers 1 Watchdog (WD) timers 1 Crystal oscillator/External clock input 1 Internal Oscillator (Optional External Precision Resistor) 2 www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 7 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 4-1. Device Comparison (continued) FEATURE(1) (4) F28P559SJ-Q1(3) F28P550SJ F28P559SG-Q1(3) F28P550SG F28P550SD Digital and Analog Pin Counts GPIO 128-pin PDT 65 65 - F28P559SG9-Q1, F28P550SG9 - 100-pin PZ 43 80-pin PNA 32 64-pin PM 17 56-pin RSH - 15 - 15 Additional GPIO 4 (2 from cJTAG and 2 from X1/X2) AIO (analog with digital inputs) 128-pin PDT 17 17 - F28P559SG9-Q1, F28P550SG9 - 100-pin PZ 16 16 80-pin PNA 12 64-pin PM 12 56-pin RSH - 12 - 12 AGPIO (analog with digital inputs and outputs) 128-pin PDT 22 22 - F28P559SG9-Q1, F28P550SG9 - 100-pin PZ 19 80-pin PNA 16 64-pin PM 16 56-pin RSH - 14 - 14 C28x Analog Peripherals(5) Analog-to-Digital Converter (ADC) (12-bit) - Type 6 Number of ADCs 5 MSPS 3.9 Conversion Time (ns)(2) 187 ADC Input channels (single-ended) (includes the two DAC outputs) 128-pin PDT 39 39 - F28P559SG9-Q1, F28P550SG9 - 100-pin PZ 35 80-pin PNA 28 64-pin PM 28 56-pin RSH 26 26 PGA - Type 2 3 Temperature Sensor 1 Comparator subsystem (CMPSS) (each CMPSS has two comparators and two internal DACs) - Type 6 4 Buffered Digital-to-Analog Converter (DAC) - Type 2 1 DAC Out from CMPSS 1 C28x Control Peripherals(5) eCAP - Type 2 Total inputs 2 ePWM/HRPWM - Type 4 Total channels - F28P559SJ9- Q1,F28P559SJ6- 16 - F28P559J2- 24 - F28P559SG9-Q1, F28P559SG8-Q1 16 - F28P559SG2 Channels with high-resolution capability 12- F28P559SJ9- Q1,F28P559SJ6- 8 - F28P559SJ2- 12 - F28P559SG9-Q1, F28P559SG8-Q1 8 - F28P559SG2 eQEP modules - Type 2 3 C28x Communications Peripherals(5) CAN with Flexible Data-Rate (CAN-FD) - Type 2 2 Fast Serial Interface (FSI) RX - Type 2 1 Fast Serial Interface (FSI) TX - Type 2 1 Inter-Integrated Circuit (I2C) - Type 2 2 Local Interconnect Network (LIN) - Type 1 1 Power Management Bus (PMBus) - Type 1 1 Serial Communications Interface (SCI) - Type 0 (UART-compatible) 3 Serial Peripheral Interface (SPI) - Type 2 2 Universal Serial Bus (USB) - Type 0 1 - F28P559SJ9-Q1, F28P550SJ9, F28P559SJ6-Q1, F28P550SJ6 1 - F28P559SG9-Q1, F28P550SG9 - TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
8 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 4-1. Device Comparison (continued) FEATURE(1) (4) F28P559SJ-Q1(3) F28P550SJ F28P559SG-Q1(3) F28P550SG F28P550SD Temperature and Qualification Junction temperature (TJ) -40°C to 150°C Free-Air temperature (TA) -40°C to 125°C Package Options 128-pin PDT F28P559SJ9-Q1, F28P559SJ6-Q1, F28P559SJ2-Q1, F28P550SJ9, F28P550SJ6, F28P559SG9-Q1, F28P550SG9 - 100-pin PZ F28P559SJ9-Q1, F28P559SJ6-Q1, F28P559SJ2-Q1, F28P550SJ9, F28P550SJ6, F28P559SG9-Q1,F28P559SG8-Q1, F28P559SG2-Q1, F28P550SG9, F28P550SG8, F28P550SD7 80-pin PNA F28P559SJ9-Q1, F28P559SJ6-Q1, F28P559SJ2-Q1, F28P550SJ9, F28P550SJ6, F28P559SG9-Q1, F28P559SG8-Q1, F28P559SG2-Q1, F28P550SG9, F28P550SG8, F28P550SD7 64-pin PM F28P559SJ9-Q1, F28P559SJ6-Q1, F28P559SJ2-Q1, F28P550SJ9, F28P550SJ6, F28P559SG9-Q1, F28P559SG8-Q1, F28P559SG2-Q1, F28P550SG9, F28P550SG8, F28P550SD7 56-pin RSH - F28P550SJ9, F28P550SJ6, F28P550SG9 - F28P550SG9, F28P550SG8, F28P550SD7 (1) A type change represents a major functional feature difference in a peripheral module. Within a peripheral type, there may be minor differences between devices that do not affect the basic functionality of the module. For more information, see the C2000 Real-Time Control Peripherals Reference Guide. (2) Time between start of sample-and-hold window to start of sample-and-hold window of the next conversion. (3) The suffix -Q1 refers to AEC Q100 qualification for automotive applications. (4) "-" on the feature entry indicates that the corresponding package type in not available. (5) For devices that are available in more than one package, the peripheral count listed in the smaller package is reduced because the smaller package has less device pins available. The number of peripherals internally present on the device is not reduced compared to the largest package offered within a part number.
4.1 Related Products
TMS320F280013x Real-Time Microcontrollers The F280013x has common pinouts with the F28P55x series of devices. The F28P55x series adds CLA and DMA support, in addition to faster CPU clock speed and increased memory size. Additionally the F28P55x has Programmable Gain Amplifiers(PGA), USB, CLB and supports live FW update. TMS320F28015x Real-Time Microcontrollers The F280015x has common pinouts with the F28P55x series of devices. The F28P55x series adds CLA and DMA support, in addition to faster CPU clock speed and increased memory size. Additionally the F28P55x has Programmable Gain Amplifiers(PGA), USB, CLB and supports live FW update. The F280015x series has lockstep C28x CPUs for safety related systems. TMS320F28003x Real-Time Microcontrollers The F28003x has common pinouts with the F28P55x series of devices. The F28P55x series has a faster overall CPU clock and increased memory options in addition to Programmable Gain Amplifiers(PGA) and USB support. The F28003x series offers SDFM support, along with BGCRC and HWBIST. www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 9 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
5 Pin Configuration and Functions
5.1 Pin Diagrams
Figure 5-1 shows the pin assignments on the 128-pin PDT thin quad flatpack. Figure 5-2 shows the pin assignments on the 100-pin PZ low-profile quad flatpack. Figure 5-3 shows the pin assignments on the 80-pin PNA thin quad flatpack. Figure 5-4 shows the pin assignments on the 64-pin PM low-profile quad flatpack. Figure 5-5 shows the pin assignments on the 56-pin RSH very thin quad flatpack no-lead.
128 GPIO3133A13,B13,C13,D13,E13,VREFLO
1 GPIO29 96 GPIO4
127 GPIO3034A13,B13,C13,D13,E13,VREFLO
2 A16,B16,C16,GPIO28 95 GPIO8
126 GPIO635A12,C1,E11,PGA3_INP
3 XRSn 94 GPIO42
125 GPIO1436B11,D16,E16,PGA3_INM
4 GPIO46 93 VREGENZ
124 GPIO1537A7,B30,C3,D12,E30
5 VDDIO 92 VSS
123 GPIO3438B5,D15,E15,PGA3_OUT
6 VDD 91 GPIO43
122 GPIO1039A8,B0,C11
7 VSS 90 VDD
121 GPIO5940VSSA
8 GPIO47 89 VDDIO
120 GPIO6141VDDA
9 GPIO66 88 GPIO19,X1
119 GPIO942A4,B8,C14
10 GPIO67 87 GPIO18,X2
118 GPIO543C26,D8,E8,GPIO211
11 GPIO48 86 GPIO74
117 GPIO8144A27,D9,E9,GPIO212
12 GPIO49 85 GPIO73
116 GPIO8045B27,D10,E10,GPIO213
13 GPIO50 84 GPIO72
115 GPIO7946C27,D18,E18,GPIO214
14 GPIO51 83 GPIO71
114 GPIO7847A28,D19,E19,GPIO215
15 GPIO52 82 GPIO58
113 GPIO7748A9,GPIO227
16 GPIO53 81 GPIO57
112 GPIO7649B4,C8,GPIO236
17 GPIO54 80 GPIO56
111 GPIO7550A10,B1,C10,GPIO230
18 A6,D14,E14,GPIO228 79 GPIO32
110 GPIO4551GPIO55
19 B2,C6,E12,GPIO226 78 GPIO35/TDI
109 VDDIO52GPIO60
20 A3,B3,C5,GPIO242,PGA2_INP 77 TMS
108 VDD53VSS
21 A2,B6,C9,GPIO224,PGA1_INP 76 GPIO37/TDO
107 VSS54VDD
22 A15,B9,C7,PGA1_INM 75 TCK
106 GPIO4455VDDIO
23 C25,D5,E5 74 GPIO70
105 GPIO756GPIO64
24 A26,D6,E6 73 GPIO69
104 GPIO2257GPIO65
25 B26,D7,E7 72 GPIO68
103 GPIO41,USB0DP58GPIO62
26 A14,B14,C4,PGA1_OUT 71 GPIO27
102 GPIO23,USB0DM59GPIO63
27 A11,B10,C0,PGA2_OUT 70 GPIO26
101 GPIO4060A17,B17,C17,GPIO20
28 A5,B12,C2,PGA2_INM 69 GPIO25
100 GPIO061A18,B18,C18,GPIO21
29 A1,B7,D11,DACB_OUT 68 B25,D4,E4,GPIO24
99 GPIO162A19,B19,C19,GPIO13
30 A0,B15,C15,DACA_OUT 67 A25,D3,E3,GPIO17
98 GPIO263A20,B20,C20,GPIO12
31 D20,E20,VREFHI 66 C24,D2,E2,GPIO16
97 GPIO364A24,D0,E0,GPIO11
32 D20,E20,VREFHI 65 B24,D1,E1,GPIO33
A. Only the GPIO function is shown on GPIO pins. See the Pin Attributes table for the complete, muxed signal name. Figure 5-1. 128-pin PDT Thin Quad Flatpack (Top View) TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
10 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
100 GPIO2926A13,B13,C13,D13,E13,VREFLO
1 A16,B16,C16,GPIO28 75 GPIO4
99 GPIO3127A13,B13,C13,D13,E13,VREFLO
2 XRSn 74 GPIO8
98 GPIO3028A12,C5
3 VDDIO 73 VREGENZ
97 GPIO629C1,E11,PGA3_INP
4 VDD 72 VSS
96 GPIO1430B11,D16,E16,PGA3_INM
5 VSS 71 VDD
95 GPIO1531A7,B30,C3,D12,E30
6 GPIO47 70 VDDIO
94 GPIO3432B5,D15,E15,PGA3_OUT
7 GPIO48 69 GPIO19,X1
93 GPIO1033VSSA
8 GPIO49 68 GPIO18,X2
92 GPIO5934VDDA
9 GPIO50 67 GPIO58
91 GPIO6135A5
10 GPIO51 66 GPIO57
90 GPIO936A4,B8
11 GPIO52 65 GPIO56
89 GPIO537A8
12 GPIO53 64 GPIO32
88 VDDIO38A9,GPIO227
13 GPIO54 63 GPIO35/TDI
87 VDD39B4,C8,GPIO236
14 A6,D14,E14,GPIO228 62 TMS
86 VSS40A10,B1,C10,GPIO230
15 B2,C6,E12,GPIO226 61 GPIO37/TDO
85 GPIO4441B0,C11,GPIO253
16 B3,GPIO242,PGA2_INP 60 TCK
84 GPIO742C14,GPIO247
17 A2,B6,C9,GPIO224,PGA1_INP 59 GPIO27
83 GPIO2243GPIO55
18 A3,B9,C7,PGA1_INM 58 GPIO26
82 GPIO41,USB0DP44GPIO60
19 A14,B14,C4,PGA1_OUT 57 GPIO25
81 GPIO23,USB0DM45VSS
20 A11,B10,C0,PGA2_OUT 56 B25,D4,E4,GPIO24
80 GPIO4046GPIO62
21 B12,C2,PGA2_INM 55 A25,D3,E3,GPIO17
79 GPIO047GPIO63
22 A1,B7,D11,DACB_OUT 54 C24,D2,E2,GPIO16
78 GPIO148A17,B17,C17,GPIO20
23 A0,B15,C15,DACA_OUT 53 B24,D1,E1,GPIO33
77 GPIO249A18,B18,C18,GPIO21
24 D20,E20,VREFHI 52 A24,D0,E0,GPIO11
76 GPIO350A19,B19,C19,GPIO13
25 D20,E20,VREFHI 51 A20,B20,C20,GPIO12
A. Only the GPIO function is shown on GPIO pins. See the Pin Attributes table for the complete, muxed signal name. Figure 5-2. 100-Pin PZ Low-Profile Quad Flatpack (Top View) www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 11 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
80 GPIO621A13,B13,C13,D13,E13,VREFLO
1 GPIO30 60 GPIO3
79 GPIO1422A12,C1,E11,PGA3_INP
2 GPIO31 59 GPIO4
78 GPIO1523A7,B30,C3,D12,E30,PGA3_INM
3 GPIO29 58 GPIO8
77 GPIO3424A8,B0,C11,PGA3_OUT
4 A16,B16,C16,GPIO28 57 GPIO42
76 GPIO1025VSSA
5 XRSn 56 VREGENZ
75 GPIO926VDDA
6 GPIO46 55 VSS
74 GPIO527A4,B8,C14
7 VDDIO 54 GPIO43
73 GPIO4528A9,B4,C8,GPIO227,GPIO236
8 VDD 53 VDD
72 VDDIO29A10,B1,C10,GPIO230
9 VSS 52 VDDIO
71 VDD30VSS
10 A6,D14,E14,GPIO228 51 GPIO19,X1
70 VSS31GPIO62
11 B2,C6,E12,GPIO226 50 GPIO18,X2
69 GPIO4432GPIO63
12 A3,B3,C5,GPIO242,PGA2_INP 49 GPIO32
68 GPIO733A17,B17,C17,GPIO20
13 A2,B6,C9,GPIO224,PGA1_INP 48 GPIO35/TDI
67 GPIO2234A18,B18,C18,GPIO21
14 A15,B9,C7,PGA1_INM 47 TMS
66 GPIO41,USB0DP35A19,B19,C19,GPIO13
15 A14,B14,C4,PGA1_OUT 46 GPIO37/TDO
65 GPIO23,USB0DM36A20,B20,C20,GPIO12
16 A11,B10,C0,PGA2_OUT 45 TCK
64 GPIO4037A24,D0,E0,GPIO11
17 A5,B12,C2,PGA2_INM 44 GPIO27
63 GPIO038B24,D1,E1,GPIO33
18 A1,B7,D11,DACB_OUT 43 GPIO26
62 GPIO139C24,D2,E2,GPIO16
19 A0,B15,C15,DACA_OUT 42 GPIO25
61 GPIO240A25,D3,E3,GPIO17
20 D20,E20,VREFHI 41 B25,D4,E4,GPIO24
A. Only the GPIO function is shown on GPIO pins. See the Pin Attributes table for the complete, muxed signal name. Figure 5-3. 80-Pin PNA Thin Quad Flatpack (Top View) TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
12 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
64 GPIO617A13,B13,C13,D13,E13,VREFLO
1 GPIO29 48 GPIO4
63 GPIO1018A12,C1,E11,PGA3_INP
2 A16,B16,C16,GPIO28 47 GPIO8
62 GPIO919A7,B30,C3,D12,E30,PGA3_INM
3 XRSn 46 VREGENZ
61 GPIO520A8,B0,C11,PGA3_OUT
4 VDD 45 VSS
60 VDDIO21VSSA
5 VSS 44 VDD
59 VDD22VDDA
6 A6,D14,E14,GPIO228 43 VDDIO
58 VSS23A4,B8,C14
7 B2,C6,E12,GPIO226 42 GPIO19,X1
57 GPIO724A9,B4,C8,GPIO227,GPIO236
8 A3,B3,C5,GPIO242,PGA2_INP 41 GPIO18,X2
56 GPIO2225A10,B1,C10,GPIO230
9 A2,B6,C9,GPIO224,PGA1_INP 40 GPIO32
55 GPIO41,USB0DP26VSS
10 A15,B9,C7,PGA1_INM 39 GPIO35/TDI
54 GPIO23,USB0DM27A17,B17,C17,GPIO20
11 A14,B14,C4,PGA1_OUT 38 TMS
53 GPIO4028A18,B18,C18,GPIO21
12 A11,B10,C0,PGA2_OUT 37 GPIO37/TDO
52 GPIO029A19,B19,C19,GPIO13
13 A5,B12,C2,PGA2_INM 36 TCK
51 GPIO130A20,B20,C20,GPIO12
14 A1,B7,D11,DACB_OUT 35 B25,D4,E4,GPIO24
50 GPIO231A24,D0,E0,GPIO11
15 A0,B15,C15,DACA_OUT 34 A25,D3,E3,GPIO17
49 GPIO332B24,D1,E1,GPIO33
16 D20,E20,VREFHI 33 C24,D2,E2,GPIO16
A. Only the GPIO function is shown on GPIO pins. See the Pin Attributes table for the complete, muxed signal name. Figure 5-4. 64-Pin PM Low-Profile Quad Flatpack (Top View) www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 13 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
56 GPIO915A13,B13,C13,D13,E13,VREFLO
1 GPIO6 42 VREGENZ
55 GPIO516A12,C1,E11,PGA3_INP
2 GPIO29 41 VDD
54 VDDIO17A7,B30,C3,D12,E30,PGA3_INM
3 A16,B16,C16,GPIO28 40 VDDIO
53 VDD18A8,B0,C11,PGA3_OUT
4 XRSn 39 GPIO19,X1
52 GPIO719VSSA
5 VDD 38 GPIO18,X2
51 GPIO2220VDDA
6 A3,B3,C5,GPIO242,PGA2_INP 37 GPIO32
50 GPIO41,USB0DP21A4,B8,C14
7 A2,B6,C9,GPIO224,PGA1_INP 36 GPIO35/TDI
49 GPIO23,USB0DM22A9,B4,C8,GPIO227,GPIO236
8 A15,B9,C7,PGA1_INM 35 TMS
48 GPIO4023A10,B1,C10,GPIO230
9 A14,B14,C4,PGA1_OUT 34 GPIO37/TDO
47 GPIO024A17,B17,C17,GPIO20
10 A11,B10,C0,PGA2_OUT 33 TCK
46 GPIO125A18,B18,C18,GPIO21
11 A5,B12,C2,PGA2_INM 32 B25,D4,E4,GPIO24
45 GPIO226A19,B19,C19,GPIO13
12 A1,B7,D11,DACB_OUT 31 A25,D3,E3,GPIO17
44 GPIO327A20,B20,C20,GPIO12
13 A0,B15,C15,DACA_OUT 30 C24,D2,E2,GPIO16
43 GPIO428A24,D0,E0,GPIO11
14 D20,E20,VREFHI 29 B24,D1,E1,GPIO33
A. Only the GPIO function is shown on GPIO pins. See the Pin Attributes table for the complete, muxed signal name. Figure 5-5. 56-Pin RSH Very Thin Quad Flatpack No-Lead (Top View) TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
14 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
5.2 Pin Attributes
Table 5-1. Pin Attributes SIGNAL NAME MUX POSITION 128 PDT 100 PZ 80 PNA 64 PM 56 RSH PIN TYPE DESCRIPTION ANALOG 30 23 19 15 13 I ADC-A Input 0 B15 I ADC-B Input 15 C15 I ADC-C Input 15 CMP3_HP2 I CMPSS-3 High Comparator Positive Input 2 CMP3_LP2 I CMPSS-3 Low Comparator Positive Input 2 DACA_OUT O Buffered DAC-A Output. AIO231 0, 4, 8, 12 I Analog Pin Used For Digital Input 231 29 22 18 14 12 I ADC-A Input 1 B7 I ADC-B Input 7 CMP1_HP4 I CMPSS-1 High Comparator Positive Input 4 CMP1_LP4 I CMPSS-1 Low Comparator Positive Input 4 D11 I ADC-D Input 11 DACB_OUT O Buffered DAC-B Output. AIO232 0, 4, 8, 12 I Analog Pin Used For Digital Input 232 21 17 13 9 7 I ADC-A Input 2 B6 I ADC-B Input 6 C9 I ADC-C Input 9 CMP1_HP0 I CMPSS-1 High Comparator Positive Input 0 CMP1_LP0 I CMPSS-1 Low Comparator Positive Input 0 GPIO224 I/O General-Purpose Input Output 224 This pin also has digital mux functions which are described in the GPIO section of this table. PGA1_INP I PGA-1 Plus I ADC-A Input 3 CMP3_HP5 I CMPSS-3 High Comparator Positive Input 5 CMP3_LP5 I CMPSS-3 Low Comparator Positive Input 5 AIO229 0, 4, 8, 12 I Analog Pin Used For Digital Input 229 20 12 8 6 I ADC-A Input 3 CMP3_HP5 I CMPSS-3 High Comparator Positive Input 5 CMP3_LP5 I CMPSS-3 Low Comparator Positive Input 5 42 36 27 23 21 I ADC-A Input 4 B8 I ADC-B Input 8 CMP2_HP0 I CMPSS-2 High Comparator Positive Input 0 CMP2_LP0 I CMPSS-2 Low Comparator Positive Input 0 AIO225 0, 4, 8, 12 I Analog Pin Used For Digital Input 225 I ADC-A Input 5 CMP2_HP5 I CMPSS-2 High Comparator Positive Input 5 CMP2_LP5 I CMPSS-2 Low Comparator Positive Input 5 AIO249 0, 4, 8, 12 I Analog Pin Used For Digital Input 249 28 17 13 11 I ADC-A Input 5 CMP2_HP5 I CMPSS-2 High Comparator Positive Input 5 CMP2_LP5 I CMPSS-2 Low Comparator Positive Input 5 www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 15 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 5-1. Pin Attributes (continued) SIGNAL NAME MUX POSITION 128 PDT 100 PZ 80 PNA 64 PM 56 RSH PIN TYPE DESCRIPTION 18 14 10 6 I ADC-A Input 6 CMP1_HP2 I CMPSS-1 High Comparator Positive Input 2 CMP1_LP2 I CMPSS-1 Low Comparator Positive Input 2 D14 I ADC-D Input 14 E14 I ADC-E Input 14 GPIO228 I/O General-Purpose Input Output 228 This pin also has digital mux functions which are described in the GPIO section of this table. 37 31 23 19 17 I ADC-A Input 7 B30 I ADC-B Input 30 C3 I ADC-C Input 3 CMP4_HN1 I CMPSS-4 High Comparator Negative Input 1 CMP4_HP1 I CMPSS-4 High Comparator Positive Input 1 CMP4_LN1 I CMPSS-4 Low Comparator Negative Input 1 CMP4_LP1 I CMPSS-4 Low Comparator Positive Input 1 D12 I ADC-D Input 12 E30 I ADC-E Input 30 AIO245 0, 4, 8, 12 I Analog Pin Used For Digital Input 245 I ADC-A Input 8 CMP4_HP4 I CMPSS-4 High Comparator Positive Input 4 CMP4_LP4 I CMPSS-4 Low Comparator Positive Input 4 AIO240 0, 4, 8, 12 I Analog Pin Used For Digital Input 240 39 24 20 18 I ADC-A Input 8 B0 I ADC-B Input 0 C11 I ADC-C Input 11 CMP4_HP4 I CMPSS-4 High Comparator Positive Input 4 CMP4_LP4 I CMPSS-4 Low Comparator Positive Input 4 AIO241 0, 4, 8, 12 I Analog Pin Used For Digital Input 241 48 38 28 24 22 I ADC-A Input 9 CMP2_HP2 I CMPSS-2 High Comparator Positive Input 2 CMP2_LP2 I CMPSS-2 Low Comparator Positive Input 2 GPIO227 I/O General-Purpose Input Output 227 This pin also has digital mux functions which are described in the GPIO section of this table. A10 50 40 29 25 23 I ADC-A Input 10 B1 I ADC-B Input 1 C10 I ADC-C Input 10 CMP2_HN0 I CMPSS-2 High Comparator Negative Input 0 CMP2_HP3 I CMPSS-2 High Comparator Positive Input 3 CMP2_LN0 I CMPSS-2 Low Comparator Negative Input 0 CMP2_LP3 I CMPSS-2 Low Comparator Positive Input 3 GPIO230 I/O General-Purpose Input Output 230 This pin also has digital mux functions which are described in the GPIO section of this table. TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
16 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 5-1. Pin Attributes (continued) SIGNAL NAME MUX POSITION 128 PDT 100 PZ 80 PNA 64 PM 56 RSH PIN TYPE DESCRIPTION A11 27 20 16 12 10 I ADC-A Input 11 B10 I ADC-B Input 10 C0 I ADC-C Input 0 CMP1_HN1 I CMPSS-1 High Comparator Negative Input 1 CMP1_HP1 I CMPSS-1 High Comparator Positive Input 1 CMP1_LN1 I CMPSS-1 Low Comparator Negative Input 1 CMP1_LP1 I CMPSS-1 Low Comparator Positive Input 1 PGA2_OUT O PGA-2 Output AIO237 0, 4, 8, 12 I Analog Pin Used For Digital Input 237 A12 35 28 22 18 16 I ADC-A Input 12 CMP2_HN1 I CMPSS-2 High Comparator Negative Input 1 CMP2_HP1 I CMPSS-2 High Comparator Positive Input 1 CMP2_LN1 I CMPSS-2 Low Comparator Negative Input 1 CMP2_LP1 I CMPSS-2 Low Comparator Positive Input 1 AIO238 0, 4, 8, 12 I Analog Pin Used For Digital Input 238 A13 34 26 21 17 15 I ADC-A Input 13 B13 I ADC-B Input 13 C13 I ADC-C Input 13 D13 I ADC-D Input 13 E13 I ADC-E Input 13 VREFLO I ADC Low Reference AIO235 0, 4, 8, 12 I Analog Pin Used For Digital Input 235 A13 33, 34 26, 27 21 17 15 I ADC-A Input 13 B13 I ADC-B Input 13 C13 I ADC-C Input 13 D13 I ADC-D Input 13 E13 I ADC-E Input 13 VREFLO I ADC Low Reference AIO235 ALT I Analog Pin Used For Digital Input 235 A14 26 19 15 11 9 I ADC-A Input 14 B14 I ADC-B Input 14 C4 I ADC-C Input 4 CMP3_HP4 I CMPSS-3 High Comparator Positive Input 4 CMP3_LP4 I CMPSS-3 Low Comparator Positive Input 4 PGA1_OUT O PGA-1 Output AIO239 0, 4, 8, 12 I Analog Pin Used For Digital Input 239 A15 22 14 10 8 I ADC-A Input 15 CMP1_HN0 I CMPSS-1 High Comparator Negative Input 0 CMP1_HP3 I CMPSS-1 High Comparator Positive Input 3 CMP1_LN0 I CMPSS-1 Low Comparator Negative Input 0 CMP1_LP3 I CMPSS-1 Low Comparator Positive Input 3 AIO233 0, 4, 8, 12 I Analog Pin Used For Digital Input 233 A16 2 1 4 2 3 I ADC-A Input 16 B16 I ADC-B Input 16 C16 I ADC-C Input 16 GPIO28 I/O General-Purpose Input Output 28 This pin also has digital mux functions which are described in the GPIO section of this table. www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 17 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 5-1. Pin Attributes (continued) SIGNAL NAME MUX POSITION 128 PDT 100 PZ 80 PNA 64 PM 56 RSH PIN TYPE DESCRIPTION A17 60 48 33 27 24 I ADC-A Input 17 B17 I ADC-B Input 17 C17 I ADC-C Input 17 GPIO20 I/O General-Purpose Input Output 20 This pin also has digital mux functions which are described in the GPIO section of this table. A18 61 49 34 28 25 I ADC-A Input 18 B18 I ADC-B Input 18 C18 I ADC-C Input 18 GPIO21 I/O General-Purpose Input Output 21 This pin also has digital mux functions which are described in the GPIO section of this table. A19 62 50 35 29 26 I ADC-A Input 19 B19 I ADC-B Input 19 C19 I ADC-C Input 19 GPIO13 I/O General-Purpose Input Output 13 This pin also has digital mux functions which are described in the GPIO section of this table. A20 63 51 36 30 27 I ADC-A Input 20 B20 I ADC-B Input 20 C20 I ADC-C Input 20 GPIO12 I/O General-Purpose Input Output 12 This pin also has digital mux functions which are described in the GPIO section of this table. A24 64 52 37 31 28 I ADC-A Input 24 D0 I ADC-D Input 0 E0 I ADC-E Input 0 GPIO11 I/O General-Purpose Input Output 11 This pin also has digital mux functions which are described in the GPIO section of this table. A25 67 55 40 34 31 I ADC-A Input 25 D3 I ADC-D Input 3 E3 I ADC-E Input 3 GPIO17 I/O General-Purpose Input Output 17 This pin also has digital mux functions which are described in the GPIO section of this table. A26 I ADC-A Input 26 D6 I ADC-D Input 6 E6 I ADC-E Input 6 AIO209 0, 4, 8, 12 I Analog Pin Used For Digital Input 209 A27 I ADC-A Input 27 AIO227 I Analog Pin Used For Digital Input 227 D9 I ADC-D Input 9 E9 I ADC-E Input 9 A28 I ADC-A Input 28 AIO243 I Analog Pin Used For Digital Input 243 D19 I ADC-D Input 19 E19 I ADC-E Input 19 I ADC-B Input 0 C11 I ADC-C Input 11 CMP2_HP3 I CMPSS-2 High Comparator Positive Input 3 CMP2_LP3 I CMPSS-2 Low Comparator Positive Input 3 GPIO231 I/O General-Purpose Input Output 231 This pin also has digital mux functions which are described in the GPIO section of this table. TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
18 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 5-1. Pin Attributes (continued) SIGNAL NAME MUX POSITION 128 PDT 100 PZ 80 PNA 64 PM 56 RSH PIN TYPE DESCRIPTION 19 15 11 7 I ADC-B Input 2 C6 I ADC-C Input 6 CMP3_HP0 I CMPSS-3 High Comparator Positive Input 0 CMP3_LP0 I CMPSS-3 Low Comparator Positive Input 0 E12 I ADC-E Input 12 GPIO226 I/O General-Purpose Input Output 226 This pin also has digital mux functions which are described in the GPIO section of this table. 20 16 12 8 6 I ADC-B Input 3 CMP3_HN0 I CMPSS-3 High Comparator Negative Input 0 CMP3_HP3 I CMPSS-3 High Comparator Positive Input 3 CMP3_LN0 I CMPSS-3 Low Comparator Negative Input 0 CMP3_LP3 I CMPSS-3 Low Comparator Positive Input 3 GPIO242 I/O General-Purpose Input Output 242 This pin also has digital mux functions which are described in the GPIO section of this table. PGA2_INP I PGA-2 Plus 49 39 28 24 22 I ADC-B Input 4 C8 I ADC-C Input 8 CMP4_HP0 I CMPSS-4 High Comparator Positive Input 0 CMP4_LP0 I CMPSS-4 Low Comparator Positive Input 0 GPIO236 0, 4, 8, 12 I/O General-Purpose Input Output 236 This pin also has digital mux functions which are described in the GPIO section of this table. 38 32 I ADC-B Input 5 CMP1_HP5 I CMPSS-1 High Comparator Positive Input 5 CMP1_LP5 I CMPSS-1 Low Comparator Positive Input 5 D15 I ADC-D Input 15 E15 I ADC-E Input 15 AIO252 0, 4, 8, 12 I Analog Pin Used For Digital Input 252 22 18 14 10 8 I ADC-B Input 9 C7 I ADC-C Input 7 PGA1_INM I PGA-1 Minus B11 36 30 I ADC-B Input 11 CMP4_HP5 I CMPSS-4 High Comparator Positive Input 5 CMP4_LP5 I CMPSS-4 Low Comparator Positive Input 5 D16 I ADC-D Input 16 E16 I ADC-E Input 16 AIO251 0, 4, 8, 12 I Analog Pin Used For Digital Input 251 B12 28 21 17 13 11 I ADC-B Input 12 C2 I ADC-C Input 2 CMP3_HN1 I CMPSS-3 High Comparator Negative Input 1 CMP3_HP1 I CMPSS-3 High Comparator Positive Input 1 CMP3_LN1 I CMPSS-3 Low Comparator Negative Input 1 CMP3_LP1 I CMPSS-3 Low Comparator Positive Input 1 PGA2_INM I PGA-2 Minus AIO244 0, 4, 8, 12 I Analog Pin Used For Digital Input 244 B24 65 53 38 32 29 I ADC-B Input 24 D1 I ADC-D Input 1 E1 I ADC-E Input 1 GPIO33 I/O General-Purpose Input Output 33 This pin also has digital mux functions which are described in the GPIO section of this table. www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 19 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 5-1. Pin Attributes (continued) SIGNAL NAME MUX POSITION 128 PDT 100 PZ 80 PNA 64 PM 56 RSH PIN TYPE DESCRIPTION B25 68 56 41 35 32 I ADC-B Input 25 D4 I ADC-D Input 4 E4 I ADC-E Input 4 GPIO24 I/O General-Purpose Input Output 24 This pin also has digital mux functions which are described in the GPIO section of this table. B26 I ADC-B Input 26 D7 I ADC-D Input 7 E7 I ADC-E Input 7 AIO210 0, 4, 8, 12 I Analog Pin Used For Digital Input 210 AIO228 I Analog Pin Used For Digital Input 228 B27 I ADC-B Input 27 D10 I ADC-D Input 10 E10 I ADC-E Input 10 35 29 22 18 16 I ADC-C Input 1 CMP4_HP2 I CMPSS-4 High Comparator Positive Input 2 CMP4_LP2 I CMPSS-4 Low Comparator Positive Input 2 E11 I ADC-E Input 11 PGA3_INP I PGA-3 Plus AIO248 0, 4, 8, 12 I Analog Pin Used For Digital Input 248 C5 20 28 12 8 6 I ADC-C Input 5 C14 I ADC-C Input 14 CMP4_HN0 I CMPSS-4 High Comparator Negative Input 0 CMP4_HP3 I CMPSS-4 High Comparator Positive Input 3 CMP4_LN0 I CMPSS-4 Low Comparator Negative Input 0 CMP4_LP3 I CMPSS-4 Low Comparator Positive Input 3 GPIO247 I/O General-Purpose Input Output 247 This pin also has digital mux functions which are described in the GPIO section of this table. C14 42 27 23 21 I ADC-C Input 14 CMP4_HN0 I CMPSS-4 High Comparator Negative Input 0 CMP4_HP3 I CMPSS-4 High Comparator Positive Input 3 CMP4_LN0 I CMPSS-4 Low Comparator Negative Input 0 CMP4_LP3 I CMPSS-4 Low Comparator Positive Input 3 C24 66 54 39 33 30 I ADC-C Input 24 D2 I ADC-D Input 2 E2 I ADC-E Input 2 GPIO16 I/O General-Purpose Input Output 16 This pin also has digital mux functions which are described in the GPIO section of this table. AIO253 I Analog Pin Used For Digital Input 253 C25 I ADC-C Input 25 D5 I ADC-D Input 5 E5 I ADC-E Input 5 AIO208 0, 4, 8, 12 I Analog Pin Used For Digital Input 208 AIO226 I Analog Pin Used For Digital Input 226 C26 I ADC-C Input 26 D8 I ADC-D Input 8 E8 I ADC-E Input 8 TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
20 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 5-1. Pin Attributes (continued) SIGNAL NAME MUX POSITION 128 PDT 100 PZ 80 PNA 64 PM 56 RSH PIN TYPE DESCRIPTION AIO242 I Analog Pin Used For Digital Input 242 C27 I ADC-C Input 27 D18 I ADC-D Input 18 E18 I ADC-E Input 18 D20 31 24 20 16 14 I ADC-D Input 20 E20 I ADC-E Input 20 VREFHI I ADC High Reference. In external reference mode, externally drive the high reference voltage onto this pin. In internal reference mode, a voltage is driven onto this pin by the device. In either mode, place at least a 2.2-µF capacitor on this pin. This capacitor should be placed as close to the device as possible between the VREFHI and VREFLO pins. AIO234 0, 4, 8, 12 I Analog Pin Used For Digital Input 234 D20 32 25 20 16 14 I ADC-D Input 20 E20 I ADC-E Input 20 VREFHI I ADC High Reference. In external reference mode, externally drive the high reference voltage onto this pin. In internal reference mode, a voltage is driven onto this pin by the device. In either mode, place at least a 2.2-µF capacitor on this pin. This capacitor should be placed as close to the device as possible between the VREFHI and VREFLO pins. AIO234 ALT I Analog Pin Used For Digital Input 234 PGA3_INM 36 30 23 19 17 I PGA-3 Minus PGA3_OUT 38 32 24 20 18 O PGA-3 Output GPIO GPIO236 0, 4, 8, 12 49 39 28 24 22 I/O General-Purpose Input Output 236 This pin also has analog functions which are described in the ANALOG section of this table. EPWM7_A 1 O ePWM-7 Output A EQEP1_INDEX 5 I/O eQEP-1 Index EPWM12_A 9 O ePWM-12 Output A GPIO0 0, 4, 8, 12 100 79 63 52 47 I/O General-Purpose Input Output 0 EPWM1_A 1 O ePWM-1 Output A OUTPUTXBAR7 3 O Output X-BAR Output 7 SCIA_RX 5 I SCI-A Receive Data I2CA_SDA 6 I/OD I2C-A Open-Drain Bidirectional Data SPIA_PTE 7 I/O SPI-A Peripheral Transmit Enable (PTE) FSIRXA_CLK 9 I FSIRX-A Input Clock MCANA_RX 10 I CAN/CAN FD Receive CLB_OUTPUTXBAR8 11 O CLB Output X-BAR Output 8 EQEP1_INDEX 13 I/O eQEP-1 Index EPWM3_A 15 O ePWM-3 Output A GPIO1 0, 4, 8, 12 99 78 62 51 46 I/O General-Purpose Input Output 1 EPWM1_B 1 O ePWM-1 Output B SCIA_TX 5 O SCI-A Transmit Data I2CA_SCL 6 I/OD I2C-A Open-Drain Bidirectional Clock SPIA_POCI 7 I/O SPI-A Peripheral Out, Controller In (POCI) EQEP1_STROBE 9 I/O eQEP-1 Strobe MCANA_TX 10 O CAN/CAN FD Transmit CLB_OUTPUTXBAR7 11 O CLB Output X-BAR Output 7 EPWM10_B 13 O ePWM-10 Output B EPWM3_B 15 O ePWM-3 Output B www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 21 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 5-1. Pin Attributes (continued) SIGNAL NAME MUX POSITION 128 PDT 100 PZ 80 PNA 64 PM 56 RSH PIN TYPE DESCRIPTION GPIO2 0, 4, 8, 12 98 77 61 50 45 I/O General-Purpose Input Output 2 EPWM2_A 1 O ePWM-2 Output A OUTPUTXBAR1 5 O Output X-BAR Output 1 PMBUSA_SDA 6 I/OD PMBus-A Open-Drain Bidirectional Data SPIA_PICO 7 I/O SPI-A Peripheral In, Controller Out (PICO) SCIA_TX 9 O SCI-A Transmit Data FSIRXA_D1 10 I FSIRX-A Optional Additional Data Input I2CB_SDA 11 I/OD I2C-B Open-Drain Bidirectional Data EPWM10_A 13 O ePWM-10 Output A MCANB_TX 14 O CAN/CAN FD Transmit EPWM4_A 15 O ePWM-4 Output A GPIO3 0, 4, 8, 12 97 76 60 49 44 I/O General-Purpose Input Output 3 EPWM2_B 1 O ePWM-2 Output B OUTPUTXBAR2 2, 5 O Output X-BAR Output 2 PMBUSA_SCL 6 I/OD PMBus-A Open-Drain Bidirectional Clock SPIA_CLK 7 I/O SPI-A Clock SCIA_RX 9 I SCI-A Receive Data FSIRXA_D0 10 I FSIRX-A Primary Data Input I2CB_SCL 11 I/OD I2C-B Open-Drain Bidirectional Clock MCANB_RX 14 I CAN/CAN FD Receive EPWM4_B 15 O ePWM-4 Output B GPIO4 0, 4, 8, 12 96 75 59 48 43 I/O General-Purpose Input Output 4 EPWM3_A 1 O ePWM-3 Output A I2CA_SCL 2 I/OD I2C-A Open-Drain Bidirectional Clock MCANA_TX 3 O CAN/CAN FD Transmit OUTPUTXBAR3 5 O Output X-BAR Output 3 SPIB_CLK 7 I/O SPI-B Clock EQEP2_STROBE 9 I/O eQEP-2 Strobe FSIRXA_CLK 10 I FSIRX-A Input Clock CLB_OUTPUTXBAR6 11 O CLB Output X-BAR Output 6 EPWM11_B 13 O ePWM-11 Output B SPIA_POCI 14 I/O SPI-A Peripheral Out, Controller In (POCI) EPWM1_A 15 O ePWM-1 Output A GPIO5 0, 4, 8, 12 118 89 74 61 55 I/O General-Purpose Input Output 5 EPWM3_B 1 O ePWM-3 Output B I2CA_SDA 2 I/OD I2C-A Open-Drain Bidirectional Data OUTPUTXBAR3 3 O Output X-BAR Output 3 MCANA_RX 5 I CAN/CAN FD Receive SPIA_PTE 7 I/O SPI-A Peripheral Transmit Enable (PTE) FSITXA_D1 9 O FSITX-A Optional Additional Data Output CLB_OUTPUTXBAR5 10 O CLB Output X-BAR Output 5 SCIA_RX 11 I SCI-A Receive Data EPWM1_B 15 O ePWM-1 Output B TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
22 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 5-1. Pin Attributes (continued) SIGNAL NAME MUX POSITION 128 PDT 100 PZ 80 PNA 64 PM 56 RSH PIN TYPE DESCRIPTION GPIO6 0, 4, 8, 12 126 97 80 64 1 I/O General-Purpose Input Output 6 EPWM4_A 1 O ePWM-4 Output A OUTPUTXBAR4 2 O Output X-BAR Output 4 SYNCOUT 3 O External ePWM Synchronization Pulse EQEP1_A 5 I eQEP-1 Input A SPIB_POCI 7 I/O SPI-B Peripheral Out, Controller In (POCI) FSITXA_D0 9 O FSITX-A Primary Data Output FSITXA_D1 11 O FSITX-A Optional Additional Data Output CLB_OUTPUTXBAR8 14 O CLB Output X-BAR Output 8 EPWM2_A 15 O ePWM-2 Output A GPIO7 0, 4, 8, 12 105 84 68 57 52 I/O General-Purpose Input Output 7 EPWM4_B 1 O ePWM-4 Output B EPWM2_A 2 O ePWM-2 Output A OUTPUTXBAR5 3 O Output X-BAR Output 5 EQEP1_B 5 I eQEP-1 Input B SPIB_PICO 7 I/O SPI-B Peripheral In, Controller Out (PICO) FSITXA_CLK 9 O FSITX-A Output Clock CLB_OUTPUTXBAR2 10 O CLB Output X-BAR Output 2 SCIA_TX 11 O SCI-A Transmit Data MCANA_TX 14 O CAN/CAN FD Transmit EPWM2_B 15 O ePWM-2 Output B GPIO8 0, 4, 8, 12 95 74 58 47 I/O General-Purpose Input Output 8 EPWM5_A 1 O ePWM-5 Output A ADCSOCAO 3 O ADC Start of Conversion A for External ADC EQEP1_STROBE 5 I/O eQEP-1 Strobe SCIA_TX 6 O SCI-A Transmit Data SPIA_PICO 7 I/O SPI-A Peripheral In, Controller Out (PICO) I2CA_SCL 9 I/OD I2C-A Open-Drain Bidirectional Clock FSITXA_D1 10 O FSITX-A Optional Additional Data Output CLB_OUTPUTXBAR5 11 O CLB Output X-BAR Output 5 EPWM11_A 13 O ePWM-11 Output A GPIO9 0, 4, 8, 12 119 90 75 62 56 I/O General-Purpose Input Output 9 EPWM5_B 1 O ePWM-5 Output B SCIB_TX 2 O SCI-B Transmit Data OUTPUTXBAR6 3 O Output X-BAR Output 6 EQEP1_INDEX 5 I/O eQEP-1 Index SCIA_RX 6 I SCI-A Receive Data SPIA_CLK 7 I/O SPI-A Clock I2CA_SCL 9 I/OD I2C-A Open-Drain Bidirectional Clock FSITXA_D0 10 O FSITX-A Primary Data Output LINA_RX 11 I LIN-A Receive PMBUSA_SCL 13 I/OD PMBus-A Open-Drain Bidirectional Clock I2CB_SCL 14 I/OD I2C-B Open-Drain Bidirectional Clock EQEP3_B 15 I eQEP-3 Input B www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 23 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 5-1. Pin Attributes (continued) SIGNAL NAME MUX POSITION 128 PDT 100 PZ 80 PNA 64 PM 56 RSH PIN TYPE DESCRIPTION GPIO10 0, 4, 8, 12 122 93 76 63 I/O General-Purpose Input Output 10 EPWM6_A 1 O ePWM-6 Output A ADCSOCBO 3 O ADC Start of Conversion B for External ADC EQEP1_A 5 I eQEP-1 Input A SCIB_TX 6 O SCI-B Transmit Data SPIA_POCI 7 I/O SPI-A Peripheral Out, Controller In (POCI) I2CA_SDA 9 I/OD I2C-A Open-Drain Bidirectional Data FSITXA_CLK 10 O FSITX-A Output Clock LINA_TX 11 O LIN-A Transmit EQEP3_STROBE 13 I/O eQEP-3 Strobe CLB_OUTPUTXBAR4 15 O CLB Output X-BAR Output 4 GPIO11 0, 4, 8, 12 64 52 37 31 28 I/O General-Purpose Input Output 11 This pin also has analog functions which are described in the ANALOG section of this table. EPWM6_B 1 O ePWM-6 Output B MCANA_RX 2 I CAN/CAN FD Receive OUTPUTXBAR7 3 O Output X-BAR Output 7 EQEP1_B 5 I eQEP-1 Input B SCIB_RX 6 I SCI-B Receive Data SPIA_PTE 7 I/O SPI-A Peripheral Transmit Enable (PTE) FSIRXA_D1 9 I FSIRX-A Optional Additional Data Input LINA_RX 10 I LIN-A Receive EQEP2_A 11 I eQEP-2 Input A SPIA_PICO 13 I/O SPI-A Peripheral In, Controller Out (PICO) EQEP3_INDEX 15 I/O eQEP-3 Index GPIO12 0, 4, 8, 12 63 51 36 30 27 I/O General-Purpose Input Output 12 This pin also has analog functions which are described in the ANALOG section of this table. EPWM7_A 1 O ePWM-7 Output A MCANA_RX 3 I CAN/CAN FD Receive EQEP1_STROBE 5 I/O eQEP-1 Strobe SCIB_TX 6 O SCI-B Transmit Data PMBUSA_CTL 7 I/O PMBus-A Control Signal - Target Input/Controller Output FSIRXA_D0 9 I FSIRX-A Primary Data Input LINA_TX 10 O LIN-A Transmit SPIA_CLK 11 I/O SPI-A Clock GPIO13 0, 4, 8, 12 62 50 35 29 26 I/O General-Purpose Input Output 13 This pin also has analog functions which are described in the ANALOG section of this table. EPWM7_B 1 O ePWM-7 Output B MCANA_TX 3 O CAN/CAN FD Transmit EQEP1_INDEX 5 I/O eQEP-1 Index SCIB_RX 6 I SCI-B Receive Data PMBUSA_ALERT 7 I/OD PMBus-A Open-Drain Bidirectional Alert Signal FSIRXA_CLK 9 I FSIRX-A Input Clock LINA_RX 10 I LIN-A Receive SPIA_POCI 11 I/O SPI-A Peripheral Out, Controller In (POCI) TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
24 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 5-1. Pin Attributes (continued) SIGNAL NAME MUX POSITION 128 PDT 100 PZ 80 PNA 64 PM 56 RSH PIN TYPE DESCRIPTION GPIO14 0, 4, 8, 12 125 96 79 I/O General-Purpose Input Output 14 EPWM8_A 1 O ePWM-8 Output A SCIB_TX 2 O SCI-B Transmit Data I2CB_SDA 5 I/OD I2C-B Open-Drain Bidirectional Data OUTPUTXBAR3 6 O Output X-BAR Output 3 PMBUSA_SDA 7 I/OD PMBus-A Open-Drain Bidirectional Data SPIB_CLK 9 I/O SPI-B Clock EQEP2_A 10 I eQEP-2 Input A LINA_TX 11 O LIN-A Transmit EPWM3_A 13 O ePWM-3 Output A CLB_OUTPUTXBAR7 14 O CLB Output X-BAR Output 7 GPIO15 0, 4, 8, 12 124 95 78 I/O General-Purpose Input Output 15 EPWM8_B 1 O ePWM-8 Output B SCIB_RX 2 I SCI-B Receive Data I2CB_SCL 5 I/OD I2C-B Open-Drain Bidirectional Clock OUTPUTXBAR4 6 O Output X-BAR Output 4 PMBUSA_SCL 7 I/OD PMBus-A Open-Drain Bidirectional Clock SPIB_PTE 9 I/O SPI-B Peripheral Transmit Enable (PTE) EQEP2_B 10 I eQEP-2 Input B LINA_RX 11 I LIN-A Receive EPWM3_B 13 O ePWM-3 Output B CLB_OUTPUTXBAR6 14 O CLB Output X-BAR Output 6 GPIO16 0, 4, 8, 12 66 54 39 33 30 I/O General-Purpose Input Output 16 This pin also has analog functions which are described in the ANALOG section of this table. SPIA_PICO 1 I/O SPI-A Peripheral In, Controller Out (PICO) OUTPUTXBAR7 3 O Output X-BAR Output 7 EPWM9_A 5 O ePWM-9 Output A SCIA_TX 6 O SCI-A Transmit Data EQEP1_STROBE 9 I/O eQEP-1 Strobe PMBUSA_SCL 10 I/OD PMBus-A Open-Drain Bidirectional Clock XCLKOUT 11 O External Clock Output. This pin outputs a divided- down version of a chosen clock signal from within the device. EQEP2_B 13 I eQEP-2 Input B SPIB_POCI 14 I/O SPI-B Peripheral Out, Controller In (POCI) EQEP3_STROBE 15 I/O eQEP-3 Strobe GPIO17 0, 4, 8, 12 67 55 40 34 31 I/O General-Purpose Input Output 17 This pin also has analog functions which are described in the ANALOG section of this table. SPIA_POCI 1 I/O SPI-A Peripheral Out, Controller In (POCI) OUTPUTXBAR8 3 O Output X-BAR Output 8 EPWM9_B 5 O ePWM-9 Output B SCIA_RX 6 I SCI-A Receive Data EQEP1_INDEX 9 I/O eQEP-1 Index PMBUSA_SDA 10 I/OD PMBus-A Open-Drain Bidirectional Data MCANA_TX 11 O CAN/CAN FD Transmit EPWM6_A 14 O ePWM-6 Output A www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 25 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 5-1. Pin Attributes (continued) SIGNAL NAME MUX POSITION 128 PDT 100 PZ 80 PNA 64 PM 56 RSH PIN TYPE DESCRIPTION GPIO18 0, 4, 8, 12 87 68 50 41 38 I/O General-Purpose Input Output 18 SPIA_CLK 1 I/O SPI-A Clock SCIB_TX 2 O SCI-B Transmit Data MCANB_RX 3 I CAN/CAN FD Receive EPWM6_A 5 O ePWM-6 Output A I2CA_SCL 6 I/OD I2C-A Open-Drain Bidirectional Clock EQEP2_A 9 I eQEP-2 Input A PMBUSA_CTL 10 I/O PMBus-A Control Signal - Target Input/Controller Output XCLKOUT 11 O External Clock Output. This pin outputs a divided- down version of a chosen clock signal from within the device. LINA_TX 13 O LIN-A Transmit EQEP3_INDEX 15 I/O eQEP-3 Index X2 ALT I/O Crystal oscillator output. GPIO19 0, 4, 8, 12 88 69 51 42 39 I/O General-Purpose Input Output 19 SPIA_PTE 1 I/O SPI-A Peripheral Transmit Enable (PTE) SCIB_RX 2 I SCI-B Receive Data MCANB_TX 3 O CAN/CAN FD Transmit EPWM6_B 5 O ePWM-6 Output B I2CA_SDA 6 I/OD I2C-A Open-Drain Bidirectional Data EQEP2_B 9 I eQEP-2 Input B PMBUSA_ALERT 10 I/OD PMBus-A Open-Drain Bidirectional Alert Signal CLB_OUTPUTXBAR1 11 O CLB Output X-BAR Output 1 LINA_RX 13 I LIN-A Receive X1 ALT I/O Crystal oscillator input or single-ended clock input. The device initialization software must configure this pin before the crystal oscillator is enabled. To use this oscillator, a quartz crystal circuit must be connected to X1 and X2. This pin can also be used to feed a single-ended 3.3-V level clock. GPIO20 0, 4, 8, 12 60 48 33 27 24 I/O General-Purpose Input Output 20 This pin also has analog functions which are described in the ANALOG section of this table. EQEP1_A 1 I eQEP-1 Input A EPWM12_A 5 O ePWM-12 Output A SPIB_PICO 6 I/O SPI-B Peripheral In, Controller Out (PICO) MCANA_TX 9 O CAN/CAN FD Transmit ADCE_EXTMUXSEL0 10 O ADCE external mux selection pin for position 0 I2CA_SCL 11 I/OD I2C-A Open-Drain Bidirectional Clock SCIC_TX 15 O SCI-C Transmit Data GPIO21 0, 4, 8, 12 61 49 34 28 25 I/O General-Purpose Input Output 21 This pin also has analog functions which are described in the ANALOG section of this table. EQEP1_B 1 I eQEP-1 Input B EPWM12_B 5 O ePWM-12 Output B SPIB_POCI 6 I/O SPI-B Peripheral Out, Controller In (POCI) MCANA_RX 9 I CAN/CAN FD Receive ADCE_EXTMUXSEL1 10 O ADCE external mux selection pin for position 1 I2CA_SDA 11 I/OD I2C-A Open-Drain Bidirectional Data SCIC_RX 15 I SCI-C Receive Data TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
26 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 5-1. Pin Attributes (continued) SIGNAL NAME MUX POSITION 128 PDT 100 PZ 80 PNA 64 PM 56 RSH PIN TYPE DESCRIPTION GPIO22 0, 4, 8, 12 104 83 67 56 51 I/O General-Purpose Input Output 22 EQEP1_STROBE 1 I/O eQEP-1 Strobe SCIB_TX 3 O SCI-B Transmit Data SPIB_CLK 6 I/O SPI-B Clock LINA_TX 9, 11 O LIN-A Transmit CLB_OUTPUTXBAR1 10 O CLB Output X-BAR Output 1 EPWM4_A 14 O ePWM-4 Output A EQEP3_A 15 I eQEP-3 Input A GPIO23 0, 4, 8, 12 102 81 65 54 49 I/O General-Purpose Input Output 23 EQEP1_INDEX 1 I/O eQEP-1 Index SCIB_RX 3 I SCI-B Receive Data SPIB_PTE 6 I/O SPI-B Peripheral Transmit Enable (PTE) LINA_RX 9, 11 I LIN-A Receive CLB_OUTPUTXBAR3 10 O CLB Output X-BAR Output 3 EPWM12_A 13 O ePWM-12 Output A EPWM4_B 14 O ePWM-4 Output B USB0DM ALT O USB-0 PHY differential data GPIO24 0, 4, 8, 12 68 56 41 35 32 I/O General-Purpose Input Output 24 This pin also has analog functions which are described in the ANALOG section of this table. OUTPUTXBAR1 1 O Output X-BAR Output 1 EQEP2_A 2 I eQEP-2 Input A SPIA_PTE 3 I/O SPI-A Peripheral Transmit Enable (PTE) EPWM8_A 5 O ePWM-8 Output A SPIB_PICO 6 I/O SPI-B Peripheral In, Controller Out (PICO) LINA_TX 9 O LIN-A Transmit PMBUSA_SCL 10 I/OD PMBus-A Open-Drain Bidirectional Clock SCIA_TX 11 O SCI-A Transmit Data ERRORSTS 13 O Error Status Output. This signal requires an external pulldown. EPWM9_A 14 O ePWM-9 Output A GPIO25 0, 4, 8, 12 69 57 42 I/O General-Purpose Input Output 25 OUTPUTXBAR2 1 O Output X-BAR Output 2 EQEP2_B 2 I eQEP-2 Input B EQEP1_A 5 I eQEP-1 Input A SPIB_POCI 6 I/O SPI-B Peripheral Out, Controller In (POCI) FSITXA_D1 9 O FSITX-A Optional Additional Data Output PMBUSA_SDA 10 I/OD PMBus-A Open-Drain Bidirectional Data SCIA_RX 11 I SCI-A Receive Data EQEP3_A 13 I eQEP-3 Input A GPIO26 0, 4, 8, 12 70 58 43 I/O General-Purpose Input Output 26 OUTPUTXBAR3 1, 5 O Output X-BAR Output 3 EQEP2_INDEX 2 I/O eQEP-2 Index SPIB_CLK 6 I/O SPI-B Clock FSITXA_D0 9 O FSITX-A Primary Data Output PMBUSA_CTL 10 I/O PMBus-A Control Signal - Target Input/Controller Output I2CA_SDA 11 I/OD I2C-A Open-Drain Bidirectional Data EQEP3_B 13 I eQEP-3 Input B www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 27 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 5-1. Pin Attributes (continued) SIGNAL NAME MUX POSITION 128 PDT 100 PZ 80 PNA 64 PM 56 RSH PIN TYPE DESCRIPTION GPIO27 0, 4, 8, 12 71 59 44 I/O General-Purpose Input Output 27 OUTPUTXBAR4 1, 5 O Output X-BAR Output 4 EQEP2_STROBE 2 I/O eQEP-2 Strobe SPIB_PTE 6 I/O SPI-B Peripheral Transmit Enable (PTE) FSITXA_CLK 9 O FSITX-A Output Clock PMBUSA_ALERT 10 I/OD PMBus-A Open-Drain Bidirectional Alert Signal I2CA_SCL 11 I/OD I2C-A Open-Drain Bidirectional Clock EQEP3_STROBE 13 I/O eQEP-3 Strobe GPIO28 0, 4, 8, 12 2 1 4 2 3 I/O General-Purpose Input Output 28 This pin also has analog functions which are described in the ANALOG section of this table. SCIA_RX 1 I SCI-A Receive Data EPWM7_A 3 O ePWM-7 Output A OUTPUTXBAR5 5 O Output X-BAR Output 5 EQEP1_A 6 I eQEP-1 Input A EQEP2_STROBE 9 I/O eQEP-2 Strobe LINA_TX 10 O LIN-A Transmit SPIB_CLK 11 I/O SPI-B Clock ERRORSTS 13 O Error Status Output. This signal requires an external pulldown. I2CB_SDA 14 I/OD I2C-B Open-Drain Bidirectional Data GPIO29 0, 4, 8, 12 1 100 3 1 2 I/O General-Purpose Input Output 29 SCIA_TX 1 O SCI-A Transmit Data EPWM7_B 3 O ePWM-7 Output B OUTPUTXBAR6 5 O Output X-BAR Output 6 EQEP1_B 6 I eQEP-1 Input B EQEP2_INDEX 9 I/O eQEP-2 Index LINA_RX 10 I LIN-A Receive SPIB_PTE 11 I/O SPI-B Peripheral Transmit Enable (PTE) ERRORSTS 13 O Error Status Output. This signal requires an external pulldown. I2CB_SCL 14 I/OD I2C-B Open-Drain Bidirectional Clock AUXCLKIN ALT I Auxilary Clock Input GPIO30 0, 4, 8, 12 127 98 1 I/O General-Purpose Input Output 30 SPIB_PICO 3 I/O SPI-B Peripheral In, Controller Out (PICO) OUTPUTXBAR7 5 O Output X-BAR Output 7 EQEP1_STROBE 6 I/O eQEP-1 Strobe FSIRXA_CLK 9 I FSIRX-A Input Clock MCANA_RX 10 I CAN/CAN FD Receive EPWM1_A 11 O ePWM-1 Output A EQEP3_INDEX 13 I/O eQEP-3 Index GPIO31 0, 4, 8, 12 128 99 2 I/O General-Purpose Input Output 31 SPIB_POCI 3 I/O SPI-B Peripheral Out, Controller In (POCI) OUTPUTXBAR8 5 O Output X-BAR Output 8 EQEP1_INDEX 6 I/O eQEP-1 Index FSIRXA_D1 9 I FSIRX-A Optional Additional Data Input MCANA_TX 10 O CAN/CAN FD Transmit EPWM1_B 11 O ePWM-1 Output B TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
28 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 5-1. Pin Attributes (continued) SIGNAL NAME MUX POSITION 128 PDT 100 PZ 80 PNA 64 PM 56 RSH PIN TYPE DESCRIPTION GPIO32 0, 4, 8, 12 79 64 49 40 37 I/O General-Purpose Input Output 32 I2CA_SDA 1 I/OD I2C-A Open-Drain Bidirectional Data EQEP1_INDEX 2 I/O eQEP-1 Index SPIB_CLK 3 I/O SPI-B Clock EPWM8_B 5 O ePWM-8 Output B LINA_TX 6 O LIN-A Transmit FSIRXA_D0 9 I FSIRX-A Primary Data Input MCANB_TX 10 O CAN/CAN FD Transmit PMBUSA_SDA 11 I/OD PMBus-A Open-Drain Bidirectional Data ADCSOCBO 13 O ADC Start of Conversion B for External ADC GPIO33 0, 4, 8, 12 65 53 38 32 29 I/O General-Purpose Input Output 33 This pin also has analog functions which are described in the ANALOG section of this table. I2CA_SCL 1 I/OD I2C-A Open-Drain Bidirectional Clock SPIB_PTE 3 I/O SPI-B Peripheral Transmit Enable (PTE) OUTPUTXBAR4 5 O Output X-BAR Output 4 LINA_RX 6 I LIN-A Receive FSIRXA_CLK 9 I FSIRX-A Input Clock MCANB_RX 10 I CAN/CAN FD Receive EQEP2_B 11 I eQEP-2 Input B ADCSOCAO 13 O ADC Start of Conversion A for External ADC SCIC_RX 15 I SCI-C Receive Data GPIO34 0, 4, 8, 12 123 94 77 I/O General-Purpose Input Output 34 OUTPUTXBAR1 1 O Output X-BAR Output 1 PMBUSA_SDA 6 I/OD PMBus-A Open-Drain Bidirectional Data I2CB_SDA 14 I/OD I2C-B Open-Drain Bidirectional Data GPIO35 0, 4, 8, 12 78 63 48 39 36 I/O General-Purpose Input Output 35 SCIA_RX 1 I SCI-A Receive Data SPIA_POCI 2 I/O SPI-A Peripheral Out, Controller In (POCI) I2CA_SDA 3 I/OD I2C-A Open-Drain Bidirectional Data MCANB_RX 5 I CAN/CAN FD Receive PMBUSA_SCL 6 I/OD PMBus-A Open-Drain Bidirectional Clock LINA_RX 7 I LIN-A Receive EQEP1_A 9 I eQEP-1 Input A PMBUSA_CTL 10 I/O PMBus-A Control Signal - Target Input/Controller Output EPWM5_B 11 O ePWM-5 Output B TDI 15 I JTAG Test Data Input (TDI) - TDI is the default mux selection for the pin. The internal pullup is disabled by default. The internal pullup should be enabled or an external pullup added on the board if this pin is used as JTAG TDI to avoid a floating input. www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 29 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 5-1. Pin Attributes (continued) SIGNAL NAME MUX POSITION 128 PDT 100 PZ 80 PNA 64 PM 56 RSH PIN TYPE DESCRIPTION GPIO37 0, 4, 8, 12 76 61 46 37 34 I/O General-Purpose Input Output 37 OUTPUTXBAR2 1 O Output X-BAR Output 2 SPIA_PTE 2 I/O SPI-A Peripheral Transmit Enable (PTE) I2CA_SCL 3 I/OD I2C-A Open-Drain Bidirectional Clock SCIA_TX 5 O SCI-A Transmit Data MCANB_TX 6 O CAN/CAN FD Transmit LINA_TX 7 O LIN-A Transmit EQEP1_B 9 I eQEP-1 Input B PMBUSA_ALERT 10 I/OD PMBus-A Open-Drain Bidirectional Alert Signal EPWM5_A 11 O ePWM-5 Output A TDO 15 O JTAG Test Data Output (TDO) - TDO is the default mux selection for the pin. The internal pullup is disabled by default. The TDO function will be in a tri- state condition when there is no JTAG activity, leaving this pin floating; the internal pullup should be enabled or an external pullup added on the board to avoid a floating GPIO input. GPIO40 0, 4, 8, 12 101 80 64 53 48 I/O General-Purpose Input Output 40 SPIB_PICO 1 I/O SPI-B Peripheral In, Controller Out (PICO) EPWM2_B 5 O ePWM-2 Output B PMBUSA_SDA 6 I/OD PMBus-A Open-Drain Bidirectional Data FSIRXA_D0 7 I FSIRX-A Primary Data Input SCIB_TX 9 O SCI-B Transmit Data EQEP1_A 10 I eQEP-1 Input A LINA_TX 11 O LIN-A Transmit CLB_OUTPUTXBAR4 14 O CLB Output X-BAR Output 4 EQEP3_STROBE 15 I/O eQEP-3 Strobe GPIO41 0, 4, 8, 12 103 82 66 55 50 I/O General-Purpose Input Output 41 EPWM7_A 1 O ePWM-7 Output A EPWM2_A 5 O ePWM-2 Output A PMBUSA_SCL 6 I/OD PMBus-A Open-Drain Bidirectional Clock FSIRXA_D1 7 I FSIRX-A Optional Additional Data Input SCIB_RX 9 I SCI-B Receive Data EQEP1_B 10 I eQEP-1 Input B LINA_RX 11 I LIN-A Receive EPWM12_B 13 O ePWM-12 Output B SPIB_POCI 14 I/O SPI-B Peripheral Out, Controller In (POCI) USB0DP ALT O USB-0 PHY differential data GPIO42 0, 4, 8, 12 94 57 I/O General-Purpose Input Output 42 LINA_RX 2 I LIN-A Receive OUTPUTXBAR5 3 O Output X-BAR Output 5 PMBUSA_CTL 5 I/O PMBus-A Control Signal - Target Input/Controller Output I2CA_SDA 6 I/OD I2C-A Open-Drain Bidirectional Data SCIC_RX 7 I SCI-C Receive Data EQEP1_STROBE 10 I/O eQEP-1 Strobe CLB_OUTPUTXBAR3 11 O CLB Output X-BAR Output 3 TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
30 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 5-1. Pin Attributes (continued) SIGNAL NAME MUX POSITION 128 PDT 100 PZ 80 PNA 64 PM 56 RSH PIN TYPE DESCRIPTION GPIO43 0, 4, 8, 12 91 54 I/O General-Purpose Input Output 43 OUTPUTXBAR6 3 O Output X-BAR Output 6 PMBUSA_ALERT 5, 9 I/OD PMBus-A Open-Drain Bidirectional Alert Signal I2CA_SCL 6 I/OD I2C-A Open-Drain Bidirectional Clock SCIC_TX 7 O SCI-C Transmit Data EQEP1_INDEX 10 I/O eQEP-1 Index CLB_OUTPUTXBAR4 11 O CLB Output X-BAR Output 4 GPIO44 0, 4, 8, 12 106 85 69 I/O General-Purpose Input Output 44 OUTPUTXBAR7 3 O Output X-BAR Output 7 EQEP1_A 5 I eQEP-1 Input A PMBUSA_SDA 6 I/OD PMBus-A Open-Drain Bidirectional Data FSITXA_CLK 7 O FSITX-A Output Clock PMBUSA_CTL 9 I/O PMBus-A Control Signal - Target Input/Controller Output CLB_OUTPUTXBAR3 10 O CLB Output X-BAR Output 3 FSIRXA_D0 11 I FSIRX-A Primary Data Input LINA_TX 14 O LIN-A Transmit GPIO45 0, 4, 8, 12 110 73 I/O General-Purpose Input Output 45 OUTPUTXBAR8 3 O Output X-BAR Output 8 FSITXA_D0 7 O FSITX-A Primary Data Output PMBUSA_ALERT 9 I/OD PMBus-A Open-Drain Bidirectional Alert Signal CLB_OUTPUTXBAR4 10 O CLB Output X-BAR Output 4 GPIO46 0, 4, 8, 12 4 6 I/O General-Purpose Input Output 46 LINA_TX 3 O LIN-A Transmit MCANA_TX 5 O CAN/CAN FD Transmit FSITXA_D1 7 O FSITX-A Optional Additional Data Output PMBUSA_SDA 9 I/OD PMBus-A Open-Drain Bidirectional Data GPIO47 0, 4, 8, 12 8 6 I/O General-Purpose Input Output 47 LINA_RX 3 I LIN-A Receive MCANA_RX 5 I CAN/CAN FD Receive CLB_OUTPUTXBAR2 7 O CLB Output X-BAR Output 2 PMBUSA_SCL 9 I/OD PMBus-A Open-Drain Bidirectional Clock GPIO48 0, 4, 8, 12 11 7 I/O General-Purpose Input Output 48 OUTPUTXBAR3 1 O Output X-BAR Output 3 MCANA_TX 5 O CAN/CAN FD Transmit SCIA_TX 6 O SCI-A Transmit Data PMBUSA_SDA 9 I/OD PMBus-A Open-Drain Bidirectional Data GPIO49 0, 4, 8, 12 12 8 I/O General-Purpose Input Output 49 OUTPUTXBAR4 1 O Output X-BAR Output 4 MCANA_RX 5 I CAN/CAN FD Receive SCIA_RX 6 I SCI-A Receive Data LINA_RX 9 I LIN-A Receive FSITXA_D0 14 O FSITX-A Primary Data Output GPIO50 0, 4, 8, 12 13 9 I/O General-Purpose Input Output 50 EQEP1_A 1 I eQEP-1 Input A MCANA_TX 5 O CAN/CAN FD Transmit SPIB_PICO 6 I/O SPI-B Peripheral In, Controller Out (PICO) I2CB_SDA 9 I/OD I2C-B Open-Drain Bidirectional Data FSITXA_D1 14 O FSITX-A Optional Additional Data Output www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 31 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 5-1. Pin Attributes (continued) SIGNAL NAME MUX POSITION 128 PDT 100 PZ 80 PNA 64 PM 56 RSH PIN TYPE DESCRIPTION GPIO51 0, 4, 8, 12 14 10 I/O General-Purpose Input Output 51 EQEP1_B 1 I eQEP-1 Input B MCANA_RX 5 I CAN/CAN FD Receive SPIB_POCI 6 I/O SPI-B Peripheral Out, Controller In (POCI) I2CB_SCL 9 I/OD I2C-B Open-Drain Bidirectional Clock FSITXA_CLK 14 O FSITX-A Output Clock GPIO52 0, 4, 8, 12 15 11 I/O General-Purpose Input Output 52 EQEP1_STROBE 1 I/O eQEP-1 Strobe CLB_OUTPUTXBAR5 5 O CLB Output X-BAR Output 5 SPIB_CLK 6 I/O SPI-B Clock SYNCOUT 9 O External ePWM Synchronization Pulse FSIRXA_D0 14 I FSIRX-A Primary Data Input GPIO53 0, 4, 8, 12 16 12 I/O General-Purpose Input Output 53 EQEP1_INDEX 1 I/O eQEP-1 Index CLB_OUTPUTXBAR6 5 O CLB Output X-BAR Output 6 SPIB_PTE 6 I/O SPI-B Peripheral Transmit Enable (PTE) ADCSOCAO 9 O ADC Start of Conversion A for External ADC MCANB_RX 10 I CAN/CAN FD Receive FSIRXA_D1 14 I FSIRX-A Optional Additional Data Input GPIO54 0, 4, 8, 12 17 13 I/O General-Purpose Input Output 54 SPIA_PICO 1 I/O SPI-A Peripheral In, Controller Out (PICO) EQEP2_A 5 I eQEP-2 Input A OUTPUTXBAR2 6 O Output X-BAR Output 2 ADCSOCBO 9 O ADC Start of Conversion B for External ADC LINA_TX 10 O LIN-A Transmit FSIRXA_CLK 14 I FSIRX-A Input Clock GPIO55 0, 4, 8, 12 51 43 I/O General-Purpose Input Output 55 SPIA_POCI 1 I/O SPI-A Peripheral Out, Controller In (POCI) EQEP2_B 5 I eQEP-2 Input B OUTPUTXBAR3 6 O Output X-BAR Output 3 ERRORSTS 9 O Error Status Output. This signal requires an external pulldown. LINA_RX 10 I LIN-A Receive GPIO56 0, 4, 8, 12 80 65 I/O General-Purpose Input Output 56 SPIA_CLK 1 I/O SPI-A Clock CLB_OUTPUTXBAR7 2 O CLB Output X-BAR Output 7 MCANA_TX 3 O CAN/CAN FD Transmit EQEP2_STROBE 5 I/O eQEP-2 Strobe SCIB_TX 6 O SCI-B Transmit Data SPIB_PICO 9 I/O SPI-B Peripheral In, Controller Out (PICO) I2CA_SDA 10 I/OD I2C-A Open-Drain Bidirectional Data EQEP1_A 11 I eQEP-1 Input A FSIRXA_D1 14 I FSIRX-A Optional Additional Data Input TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
32 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 5-1. Pin Attributes (continued) SIGNAL NAME MUX POSITION 128 PDT 100 PZ 80 PNA 64 PM 56 RSH PIN TYPE DESCRIPTION GPIO57 0, 4, 8, 12 81 66 I/O General-Purpose Input Output 57 SPIA_PTE 1 I/O SPI-A Peripheral Transmit Enable (PTE) CLB_OUTPUTXBAR8 2 O CLB Output X-BAR Output 8 MCANA_RX 3 I CAN/CAN FD Receive EQEP2_INDEX 5 I/O eQEP-2 Index SCIB_RX 6 I SCI-B Receive Data SPIB_POCI 9 I/O SPI-B Peripheral Out, Controller In (POCI) I2CA_SCL 10 I/OD I2C-A Open-Drain Bidirectional Clock EQEP1_B 11 I eQEP-1 Input B FSIRXA_CLK 14 I FSIRX-A Input Clock GPIO58 0, 4, 8, 12 82 67 I/O General-Purpose Input Output 58 OUTPUTXBAR1 5 O Output X-BAR Output 1 SPIB_CLK 6 I/O SPI-B Clock LINA_TX 9 O LIN-A Transmit MCANB_TX 10 O CAN/CAN FD Transmit EQEP1_STROBE 11 I/O eQEP-1 Strobe FSIRXA_D0 14 I FSIRX-A Primary Data Input GPIO59 0, 4, 8, 12 121 92 I/O General-Purpose Input Output 59 OUTPUTXBAR2 5 O Output X-BAR Output 2 SPIB_PTE 6 I/O SPI-B Peripheral Transmit Enable (PTE) LINA_RX 9 I LIN-A Receive MCANB_RX 10 I CAN/CAN FD Receive EQEP1_INDEX 11 I/O eQEP-1 Index GPIO60 0, 4, 8, 12 52 44 I/O General-Purpose Input Output 60 EPWM12_B 1 O ePWM-12 Output B MCANA_TX 3 O CAN/CAN FD Transmit OUTPUTXBAR3 5 O Output X-BAR Output 3 SPIB_PICO 6 I/O SPI-B Peripheral In, Controller Out (PICO) GPIO61 0, 4, 8, 12 120 91 I/O General-Purpose Input Output 61 MCANA_RX 3 I CAN/CAN FD Receive OUTPUTXBAR4 5 O Output X-BAR Output 4 SPIB_POCI 6 I/O SPI-B Peripheral Out, Controller In (POCI) MCANB_RX 14 I CAN/CAN FD Receive GPIO62 0, 4, 8, 12 58 46 31 I/O General-Purpose Input Output 62 EPWM10_A 1 O ePWM-10 Output A OUTPUTXBAR3 2 O Output X-BAR Output 3 MCANA_TX 5 O CAN/CAN FD Transmit SCIA_TX 6 O SCI-A Transmit Data PMBUSA_SDA 9 I/OD PMBus-A Open-Drain Bidirectional Data GPIO63 0, 4, 8, 12 59 47 32 I/O General-Purpose Input Output 63 EPWM10_B 1 O ePWM-10 Output B OUTPUTXBAR4 2 O Output X-BAR Output 4 MCANA_RX 5 I CAN/CAN FD Receive SCIA_RX 6 I SCI-A Receive Data LINA_RX 9 I LIN-A Receive www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 33 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 5-1. Pin Attributes (continued) SIGNAL NAME MUX POSITION 128 PDT 100 PZ 80 PNA 64 PM 56 RSH PIN TYPE DESCRIPTION GPIO64 0, 4, 8, 12 I/O General-Purpose Input Output 64 SCIA_RX 1 I SCI-A Receive Data EPWM11_A 2 O ePWM-11 Output A EPWM7_A 3 O ePWM-7 Output A OUTPUTXBAR5 5 O Output X-BAR Output 5 EQEP1_A 6 I eQEP-1 Input A EQEP2_STROBE 9 I/O eQEP-2 Strobe LINA_TX 10 O LIN-A Transmit SPIB_CLK 11 I/O SPI-B Clock ERRORSTS 13 O Error Status Output. This signal requires an external pulldown. I2CB_SDA 14 I/OD I2C-B Open-Drain Bidirectional Data GPIO65 0, 4, 8, 12 I/O General-Purpose Input Output 65 EQEP1_A 1 I eQEP-1 Input A EPWM11_B 2 O ePWM-11 Output B SPIB_PICO 6 I/O SPI-B Peripheral In, Controller Out (PICO) MCANA_TX 9 O CAN/CAN FD Transmit I2CA_SCL 11 I/OD I2C-A Open-Drain Bidirectional Clock GPIO66 0, 4, 8, 12 I/O General-Purpose Input Output 66 EQEP1_B 1 I eQEP-1 Input B EPWM12_A 2 O ePWM-12 Output A SPIB_POCI 6 I/O SPI-B Peripheral Out, Controller In (POCI) MCANA_RX 9 I CAN/CAN FD Receive I2CA_SDA 11 I/OD I2C-A Open-Drain Bidirectional Data GPIO67 0, 4, 8, 12 I/O General-Purpose Input Output 67 EPWM7_B 1 O ePWM-7 Output B EPWM12_B 2 O ePWM-12 Output B MCANA_TX 3 O CAN/CAN FD Transmit EQEP1_INDEX 5 I/O eQEP-1 Index SCIB_RX 6 I SCI-B Receive Data PMBUSA_ALERT 7 I/OD PMBus-A Open-Drain Bidirectional Alert Signal FSIRXA_CLK 9 I FSIRX-A Input Clock LINA_RX 10 I LIN-A Receive SPIA_POCI 11 I/O SPI-A Peripheral Out, Controller In (POCI) SCIC_RX 15 I SCI-C Receive Data GPIO68 0, 4, 8, 12 I/O General-Purpose Input Output 68 EPWM7_A 1 O ePWM-7 Output A EPWM3_A 2 O ePWM-3 Output A MCANA_RX 3 I CAN/CAN FD Receive EQEP1_STROBE 5 I/O eQEP-1 Strobe SCIB_TX 6 O SCI-B Transmit Data PMBUSA_CTL 7 I/O PMBus-A Control Signal - Target Input/Controller Output FSIRXA_D0 9 I FSIRX-A Primary Data Input LINA_TX 10 O LIN-A Transmit SPIA_CLK 11 I/O SPI-A Clock SCIC_TX 15 O SCI-C Transmit Data TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
34 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 5-1. Pin Attributes (continued) SIGNAL NAME MUX POSITION 128 PDT 100 PZ 80 PNA 64 PM 56 RSH PIN TYPE DESCRIPTION GPIO69 0, 4, 8, 12 I/O General-Purpose Input Output 69 EPWM6_B 1 O ePWM-6 Output B EPWM3_B 2 O ePWM-3 Output B OUTPUTXBAR7 3 O Output X-BAR Output 7 EQEP1_B 5 I eQEP-1 Input B SCIB_RX 6 I SCI-B Receive Data SPIA_PTE 7 I/O SPI-A Peripheral Transmit Enable (PTE) FSIRXA_D1 9 I FSIRX-A Optional Additional Data Input LINA_RX 10 I LIN-A Receive EQEP2_A 11 I eQEP-2 Input A SPIA_PICO 13 I/O SPI-A Peripheral In, Controller Out (PICO) EQEP3_INDEX 15 I/O eQEP-3 Index GPIO70 0, 4, 8, 12 I/O General-Purpose Input Output 70 I2CA_SCL 1 I/OD I2C-A Open-Drain Bidirectional Clock SPIB_PTE 3 I/O SPI-B Peripheral Transmit Enable (PTE) OUTPUTXBAR4 5 O Output X-BAR Output 4 LINA_RX 6 I LIN-A Receive FSIRXA_CLK 9 I FSIRX-A Input Clock MCANA_RX 10 I CAN/CAN FD Receive EQEP2_B 11 I eQEP-2 Input B ADCSOCAO 13 O ADC Start of Conversion A for External ADC EQEP3_A 15 I eQEP-3 Input A GPIO71 0, 4, 8, 12 I/O General-Purpose Input Output 71 SPIA_PICO 1 I/O SPI-A Peripheral In, Controller Out (PICO) EPWM4_B 2 O ePWM-4 Output B OUTPUTXBAR7 3 O Output X-BAR Output 7 EPWM9_A 5 O ePWM-9 Output A SCIA_TX 6 O SCI-A Transmit Data EQEP1_STROBE 9 I/O eQEP-1 Strobe PMBUSA_SCL 10 I/OD PMBus-A Open-Drain Bidirectional Clock XCLKOUT 11 O External Clock Output. This pin outputs a divided- down version of a chosen clock signal from within the device. EQEP2_INDEX 13 I/O eQEP-2 Index SPIB_POCI 14 I/O SPI-B Peripheral Out, Controller In (POCI) EQEP3_STROBE 15 I/O eQEP-3 Strobe GPIO72 0, 4, 8, 12 I/O General-Purpose Input Output 72 SPIA_POCI 1 I/O SPI-A Peripheral Out, Controller In (POCI) EPWM5_A 2 O ePWM-5 Output A OUTPUTXBAR8 3 O Output X-BAR Output 8 EPWM9_B 5 O ePWM-9 Output B SCIA_RX 6 I SCI-A Receive Data EQEP1_INDEX 9 I/O eQEP-1 Index PMBUSA_SDA 10 I/OD PMBus-A Open-Drain Bidirectional Data MCANA_TX 11 O CAN/CAN FD Transmit EPWM6_A 14 O ePWM-6 Output A EQEP3_B 15 I eQEP-3 Input B www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 35 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 5-1. Pin Attributes (continued) SIGNAL NAME MUX POSITION 128 PDT 100 PZ 80 PNA 64 PM 56 RSH PIN TYPE DESCRIPTION GPIO73 0, 4, 8, 12 I/O General-Purpose Input Output 73 OUTPUTXBAR1 1 O Output X-BAR Output 1 EPWM5_B 2 O ePWM-5 Output B SPIA_PTE 3 I/O SPI-A Peripheral Transmit Enable (PTE) EPWM8_A 5 O ePWM-8 Output A SPIB_PICO 6 I/O SPI-B Peripheral In, Controller Out (PICO) LINA_TX 9 O LIN-A Transmit PMBUSA_SCL 10 I/OD PMBus-A Open-Drain Bidirectional Clock SCIA_TX 11 O SCI-A Transmit Data ERRORSTS 13 O Error Status Output. This signal requires an external pulldown. EPWM9_A 14 O ePWM-9 Output A GPIO74 0, 4, 8, 12 I/O General-Purpose Input Output 74 EPWM2_B 1 O ePWM-2 Output B ADCSOCAO 3 O ADC Start of Conversion A for External ADC MCANA_TX 5 O CAN/CAN FD Transmit SPIA_POCI 6 I/O SPI-A Peripheral Out, Controller In (POCI) EQEP1_B 11 I eQEP-1 Input B GPIO75 0, 4, 8, 12 111 I/O General-Purpose Input Output 75 EPWM1_B 1 O ePWM-1 Output B LINA_RX 3 I LIN-A Receive EPWM6_A 5 O ePWM-6 Output A SPIA_CLK 6 I/O SPI-A Clock EQEP1_STROBE 11 I/O eQEP-1 Strobe SCIC_RX 14 I SCI-C Receive Data GPIO76 0, 4, 8, 12 112 I/O General-Purpose Input Output 76 EPWM4_A 1 O ePWM-4 Output A OUTPUTXBAR2 5 O Output X-BAR Output 2 SPIA_PTE 6 I/O SPI-A Peripheral Transmit Enable (PTE) MCANA_RX 10 I CAN/CAN FD Receive EQEP1_INDEX 11 I/O eQEP-1 Index GPIO77 0, 4, 8, 12 113 I/O General-Purpose Input Output 77 EPWM1_A 1 O ePWM-1 Output A OUTPUTXBAR3 5 O Output X-BAR Output 3 SPIA_PICO 6 I/O SPI-A Peripheral In, Controller Out (PICO) MCANA_TX 10 O CAN/CAN FD Transmit EQEP1_A 11 I eQEP-1 Input A SCIC_TX 14 O SCI-C Transmit Data GPIO78 0, 4, 8, 12 114 I/O General-Purpose Input Output 78 EPWM8_A 2 O ePWM-8 Output A EPWM3_A 3 O ePWM-3 Output A OUTPUTXBAR1 5 O Output X-BAR Output 1 EPWM2_B 6 O ePWM-2 Output B FSITXA_CLK 9 O FSITX-A Output Clock TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
36 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 5-1. Pin Attributes (continued) SIGNAL NAME MUX POSITION 128 PDT 100 PZ 80 PNA 64 PM 56 RSH PIN TYPE DESCRIPTION GPIO79 0, 4, 8, 12 115 I/O General-Purpose Input Output 79 EPWM8_B 2 O ePWM-8 Output B EPWM3_B 3 O ePWM-3 Output B MCANA_RX 5 I CAN/CAN FD Receive EPWM2_A 6 O ePWM-2 Output A I2CA_SDA 7 I/OD I2C-A Open-Drain Bidirectional Data PMBUSA_SCL 9 I/OD PMBus-A Open-Drain Bidirectional Clock GPIO80 0, 4, 8, 12 116 I/O General-Purpose Input Output 80 EPWM1_A 1 O ePWM-1 Output A OUTPUTXBAR7 3 O Output X-BAR Output 7 SCIA_RX 5 I SCI-A Receive Data I2CB_SDA 6 I/OD I2C-B Open-Drain Bidirectional Data SPIA_PTE 7 I/O SPI-A Peripheral Transmit Enable (PTE) FSITXA_D0 9 O FSITX-A Primary Data Output MCANA_RX 10 I CAN/CAN FD Receive CLB_OUTPUTXBAR8 11 O CLB Output X-BAR Output 8 EQEP1_INDEX 13 I/O eQEP-1 Index EPWM3_A 15 O ePWM-3 Output A GPIO81 0, 4, 8, 12 117 I/O General-Purpose Input Output 81 EPWM1_B 1 O ePWM-1 Output B OUTPUTXBAR6 2 O Output X-BAR Output 6 SCIC_RX 3 I SCI-C Receive Data SPIB_CLK 5 I/O SPI-B Clock I2CB_SCL 6 I/OD I2C-B Open-Drain Bidirectional Clock FSITXA_D1 9 O FSITX-A Optional Additional Data Output MCANA_TX 10 O CAN/CAN FD Transmit EQEP3_INDEX 11 I/O eQEP-3 Index GPIO211 0, 4, 8, 12 I/O General-Purpose Input Output 211 EPWM10_A 1 O ePWM-10 Output A EQEP3_A 5 I eQEP-3 Input A GPIO212 0, 4, 8, 12 I/O General-Purpose Input Output 212 EPWM10_B 1 O ePWM-10 Output B EQEP3_B 5 I eQEP-3 Input B GPIO213 0, 4, 8, 12 I/O General-Purpose Input Output 213 EPWM11_A 1 O ePWM-11 Output A EQEP3_STROBE 5 I/O eQEP-3 Strobe GPIO214 0, 4, 8, 12 I/O General-Purpose Input Output 214 EPWM11_B 1 O ePWM-11 Output B EQEP3_INDEX 5 I/O eQEP-3 Index GPIO215 0, 4, 8, 12 I/O General-Purpose Input Output 215 EPWM7_B 1 O ePWM-7 Output B EQEP2_A 5 I eQEP-2 Input A www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 37 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 5-1. Pin Attributes (continued) SIGNAL NAME MUX POSITION 128 PDT 100 PZ 80 PNA 64 PM 56 RSH PIN TYPE DESCRIPTION GPIO224 0, 4, 8, 12 21 17 13 9 7 I/O General-Purpose Input Output 224 This pin also has analog functions which are described in the ANALOG section of this table. EPWM11_B 1 O ePWM-11 Output B OUTPUTXBAR3 5 O Output X-BAR Output 3 SPIA_PICO 6 I/O SPI-A Peripheral In, Controller Out (PICO) EPWM1_A 9 O ePWM-1 Output A MCANA_TX 10 O CAN/CAN FD Transmit EQEP1_A 11 I eQEP-1 Input A ADCE_EXTMUXSEL3 13 O ADCE external mux selection pin for position 3 SCIC_TX 14 O SCI-C Transmit Data GPIO226 0, 4, 8, 12 19 15 11 7 I/O General-Purpose Input Output 226 This pin also has analog functions which are described in the ANALOG section of this table. EPWM10_B 1 O ePWM-10 Output B LINA_RX 3 I LIN-A Receive EPWM6_A 5 O ePWM-6 Output A SPIA_CLK 6 I/O SPI-A Clock EPWM1_B 9 O ePWM-1 Output B EQEP1_STROBE 11 I/O eQEP-1 Strobe ADCE_EXTMUXSEL1 13 O ADCE external mux selection pin for position 1 SCIC_RX 14 I SCI-C Receive Data GPIO227 0, 4, 8, 12 48 38 28 24 22 I/O General-Purpose Input Output 227 This pin also has analog functions which are described in the ANALOG section of this table. I2CB_SCL 1 I/OD I2C-B Open-Drain Bidirectional Clock EPWM3_A 3 O ePWM-3 Output A OUTPUTXBAR1 5 O Output X-BAR Output 1 EPWM2_B 6 O ePWM-2 Output B GPIO228 0, 4, 8, 12 18 14 10 6 I/O General-Purpose Input Output 228 This pin also has analog functions which are described in the ANALOG section of this table. EPWM10_A 1 O ePWM-10 Output A ADCSOCAO 3 O ADC Start of Conversion A for External ADC MCANA_TX 5 O CAN/CAN FD Transmit SPIA_POCI 6 I/O SPI-A Peripheral Out, Controller In (POCI) EPWM2_B 9 O ePWM-2 Output B EQEP1_B 11 I eQEP-1 Input B ADCE_EXTMUXSEL0 13 O ADCE external mux selection pin for position 0 GPIO230 0, 4, 8, 12 50 40 29 25 23 I/O General-Purpose Input Output 230 This pin also has analog functions which are described in the ANALOG section of this table. I2CB_SDA 1 I/OD I2C-B Open-Drain Bidirectional Data EPWM3_B 3 O ePWM-3 Output B MCANA_RX 5 I CAN/CAN FD Receive EPWM2_A 6 O ePWM-2 Output A I2CA_SDA 7 I/OD I2C-A Open-Drain Bidirectional Data PMBUSA_SCL 9 I/OD PMBus-A Open-Drain Bidirectional Clock TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
38 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 5-1. Pin Attributes (continued) SIGNAL NAME MUX POSITION 128 PDT 100 PZ 80 PNA 64 PM 56 RSH PIN TYPE DESCRIPTION GPIO242 0, 4, 8, 12 20 16 12 8 6 I/O General-Purpose Input Output 242 This pin also has analog functions which are described in the ANALOG section of this table. EPWM11_A 1 O ePWM-11 Output A OUTPUTXBAR2 5 O Output X-BAR Output 2 SPIA_PTE 6 I/O SPI-A Peripheral Transmit Enable (PTE) EPWM4_A 9 O ePWM-4 Output A MCANA_RX 10 I CAN/CAN FD Receive EQEP1_INDEX 11 I/O eQEP-1 Index ADCE_EXTMUXSEL2 13 O ADCE external mux selection pin for position 2 GPIO247 0, 4, 8, 12 I/O General-Purpose Input Output 247 This pin also has analog functions which are described in the ANALOG section of this table. EPWM12_B 1 O ePWM-12 Output B GPIO253 0, 4, 8, 12 I/O General-Purpose Input Output 253 EPWM12_A 1 O ePWM-12 Output A TEST, JTAG, AND RESET TCK 75 60 45 36 33 I JTAG test clock with internal pullup. TMS 77 62 47 38 35 I/O JTAG test-mode select (TMS) with internal pullup. This serial control input is clocked into the TAP controller on the rising edge of TCK. This device does not have a TRSTn pin. An external pullup resistor (recommended 2.2 kΩ) on the TMS pin to VDDIO should be placed on the board to keep JTAG in reset during normal operation. XRSn 3 2 5 3 4 I/OD Device Reset (in) and Watchdog Reset (out). During a power-on condition, this pin is driven low by the device. An external circuit may also drive this pin to assert a device reset. This pin is also driven low by the MCU when a watchdog reset occurs. During watchdog reset, the XRSn pin is driven low for the watchdog reset duration of 512 OSCCLK cycles. A resistor between 2.2 kΩ and 10 kΩ should be placed between XRSn and VDDIO. If a capacitor is placed between XRSn and VSS for noise filtering, it should be 100 nF or smaller. These values will allow the watchdog to properly drive the XRSn pin to VOL within 512 OSCCLK cycles when the watchdog reset is asserted. This pin is an open-drain output with an internal pullup. If this pin is driven by an external device, it should be done using an open-drain device. POWER AND GROUND VDD 6, 54, 90, 108 4, 71, 8, 53, 4, 44, 5, 41, 1.2-V Digital Logic Power Pins. TI recommends placing a decoupling capacitor near each VDD pin with a minimum total capacitance of approximately 10 µF. It is also recommended that all VDD pins be externally connected to each other when internal VREG is used. VDDA 41 34 26 22 20 3.3-V Analog Power Pins. Place a minimum 2.2-µF decoupling capacitor on each pin. VDDIO 5, 55, 89, 109 3, 70, 7, 52, 72 43, 60 40, 54 3.3-V Digital I/O Power Pins. Place a minimum 0.1-µF decoupling capacitor on each pin. VREGENZ 93 73 56 46 42 I Internal voltage regulator enable with internal pulldown. Tie low to VSS to enable internal VREG. Tie high to VDDIO to use an external supply. VSS 7, 53, 92, 107 5, 45, 72, 86 9, 30, 55, 70 5, 26, 45, 58 PAD Digital Ground VSSA 40 33 25 21 19 Analog Ground www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 39 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
5.3 Signal Descriptions
5.3.1 Analog Signals
Table 5-2. Analog Signals SIGNAL NAME PIN TYPE DESCRIPTION 128 PDT 100 PZ 80 PNA 64 PM 56 RSH A0 I ADC-A Input 0 30 23 19 15 13 A1 I ADC-A Input 1 29 22 18 14 12 A2 I ADC-A Input 2 21 17 13 9 7 A3 I ADC-A Input 3 20 18 12 8 6 A4 I ADC-A Input 4 42 36 27 23 21 A5 I ADC-A Input 5 28 35 17 13 11 A6 I ADC-A Input 6 18 14 10 6 A7 I ADC-A Input 7 37 31 23 19 17 A8 I ADC-A Input 8 39 37 24 20 18 A9 I ADC-A Input 9 48 38 28 24 22 A10 I ADC-A Input 10 50 40 29 25 23 A11 I ADC-A Input 11 27 20 16 12 10 A12 I ADC-A Input 12 35 28 22 18 16 A13 I ADC-A Input 13 33, 34 26, 27 21 17 15 A14 I ADC-A Input 14 26 19 15 11 9 A15 I ADC-A Input 15 22 14 10 8 A16 I ADC-A Input 16 2 1 4 2 3 A17 I ADC-A Input 17 60 48 33 27 24 A18 I ADC-A Input 18 61 49 34 28 25 A19 I ADC-A Input 19 62 50 35 29 26 A20 I ADC-A Input 20 63 51 36 30 27 A24 I ADC-A Input 24 64 52 37 31 28 A25 I ADC-A Input 25 67 55 40 34 31 A26 I ADC-A Input 26 24 A27 I ADC-A Input 27 44 A28 I ADC-A Input 28 47 AIO208 I Analog Pin Used For Digital Input 208 23 AIO209 I Analog Pin Used For Digital Input 209 24 AIO210 I Analog Pin Used For Digital Input 210 25 AIO225 I Analog Pin Used For Digital Input 225 42 36 27 23 21 AIO226 I Analog Pin Used For Digital Input 226 43 AIO227 I Analog Pin Used For Digital Input 227 44 AIO228 I Analog Pin Used For Digital Input 228 45 AIO229 I Analog Pin Used For Digital Input 229 18 AIO231 I Analog Pin Used For Digital Input 231 30 23 19 15 13 AIO232 I Analog Pin Used For Digital Input 232 29 22 18 14 12 AIO233 I Analog Pin Used For Digital Input 233 22 14 10 8 AIO234 I Analog Pin Used For Digital Input 234 31, 32 24, 25 20 16 14 AIO235 I Analog Pin Used For Digital Input 235 33, 34 26, 27 21 17 15 AIO237 I Analog Pin Used For Digital Input 237 27 20 16 12 10 AIO238 I Analog Pin Used For Digital Input 238 35 28 22 18 16 AIO239 I Analog Pin Used For Digital Input 239 26 19 15 11 9 TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
40 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 5-2. Analog Signals (continued) SIGNAL NAME PIN TYPE DESCRIPTION 128 PDT 100 PZ 80 PNA 64 PM 56 RSH AIO240 I Analog Pin Used For Digital Input 240 37 AIO241 I Analog Pin Used For Digital Input 241 39 24 20 18 AIO242 I Analog Pin Used For Digital Input 242 46 AIO243 I Analog Pin Used For Digital Input 243 47 AIO244 I Analog Pin Used For Digital Input 244 28 21 17 13 11 AIO245 I Analog Pin Used For Digital Input 245 37 31 23 19 17 AIO248 I Analog Pin Used For Digital Input 248 35 29 22 18 16 AIO249 I Analog Pin Used For Digital Input 249 35 AIO251 I Analog Pin Used For Digital Input 251 36 30 AIO252 I Analog Pin Used For Digital Input 252 38 32 AIO253 I Analog Pin Used For Digital Input 253 23 B0 I ADC-B Input 0 39 41 24 20 18 B1 I ADC-B Input 1 50 40 29 25 23 B2 I ADC-B Input 2 19 15 11 7 B3 I ADC-B Input 3 20 16 12 8 6 B4 I ADC-B Input 4 49 39 28 24 22 B5 I ADC-B Input 5 38 32 B6 I ADC-B Input 6 21 17 13 9 7 B7 I ADC-B Input 7 29 22 18 14 12 B8 I ADC-B Input 8 42 36 27 23 21 B9 I ADC-B Input 9 22 18 14 10 8 B10 I ADC-B Input 10 27 20 16 12 10 B11 I ADC-B Input 11 36 30 B12 I ADC-B Input 12 28 21 17 13 11 B13 I ADC-B Input 13 33, 34 26, 27 21 17 15 B14 I ADC-B Input 14 26 19 15 11 9 B15 I ADC-B Input 15 30 23 19 15 13 B16 I ADC-B Input 16 2 1 4 2 3 B17 I ADC-B Input 17 60 48 33 27 24 B18 I ADC-B Input 18 61 49 34 28 25 B19 I ADC-B Input 19 62 50 35 29 26 B20 I ADC-B Input 20 63 51 36 30 27 B24 I ADC-B Input 24 65 53 38 32 29 B25 I ADC-B Input 25 68 56 41 35 32 B26 I ADC-B Input 26 25 B27 I ADC-B Input 27 45 B30 I ADC-B Input 30 37 31 23 19 17 C0 I ADC-C Input 0 27 20 16 12 10 C1 I ADC-C Input 1 35 29 22 18 16 C2 I ADC-C Input 2 28 21 17 13 11 C3 I ADC-C Input 3 37 31 23 19 17 C4 I ADC-C Input 4 26 19 15 11 9 C5 I ADC-C Input 5 20 28 12 8 6 C6 I ADC-C Input 6 19 15 11 7 www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 41 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 5-2. Analog Signals (continued) SIGNAL NAME PIN TYPE DESCRIPTION 128 PDT 100 PZ 80 PNA 64 PM 56 RSH C7 I ADC-C Input 7 22 18 14 10 8 C8 I ADC-C Input 8 49 39 28 24 22 C9 I ADC-C Input 9 21 17 13 9 7 C10 I ADC-C Input 10 50 40 29 25 23 C11 I ADC-C Input 11 39 41 24 20 18 C13 I ADC-C Input 13 33, 34 26, 27 21 17 15 C14 I ADC-C Input 14 42 42 27 23 21 C15 I ADC-C Input 15 30 23 19 15 13 C16 I ADC-C Input 16 2 1 4 2 3 C17 I ADC-C Input 17 60 48 33 27 24 C18 I ADC-C Input 18 61 49 34 28 25 C19 I ADC-C Input 19 62 50 35 29 26 C20 I ADC-C Input 20 63 51 36 30 27 C24 I ADC-C Input 24 66 54 39 33 30 C25 I ADC-C Input 25 23 C26 I ADC-C Input 26 43 C27 I ADC-C Input 27 46 CMP1_HN0 I CMPSS-1 High Comparator Negative Input 0 22 14 10 8 CMP1_HN1 I CMPSS-1 High Comparator Negative Input 1 27 20 16 12 10 CMP1_HP0 I CMPSS-1 High Comparator Positive Input 0 21 17 13 9 7 CMP1_HP1 I CMPSS-1 High Comparator Positive Input 1 27 20 16 12 10 CMP1_HP2 I CMPSS-1 High Comparator Positive Input 2 18 14 10 6 CMP1_HP3 I CMPSS-1 High Comparator Positive Input 3 22 14 10 8 CMP1_HP4 I CMPSS-1 High Comparator Positive Input 4 29 22 18 14 12 CMP1_HP5 I CMPSS-1 High Comparator Positive Input 5 38 32 CMP1_LN0 I CMPSS-1 Low Comparator Negative Input 0 22 14 10 8 CMP1_LN1 I CMPSS-1 Low Comparator Negative Input 1 27 20 16 12 10 CMP1_LP0 I CMPSS-1 Low Comparator Positive Input 0 21 17 13 9 7 CMP1_LP1 I CMPSS-1 Low Comparator Positive Input 1 27 20 16 12 10 CMP1_LP2 I CMPSS-1 Low Comparator Positive Input 2 18 14 10 6 CMP1_LP3 I CMPSS-1 Low Comparator Positive Input 3 22 14 10 8 CMP1_LP4 I CMPSS-1 Low Comparator Positive Input 4 29 22 18 14 12 CMP1_LP5 I CMPSS-1 Low Comparator Positive Input 5 38 32 CMP2_HN0 I CMPSS-2 High Comparator Negative Input 0 50 40 29 25 23 CMP2_HN1 I CMPSS-2 High Comparator Negative Input 1 35 28 22 18 16 CMP2_HP0 I CMPSS-2 High Comparator Positive Input 0 42 36 27 23 21 CMP2_HP1 I CMPSS-2 High Comparator Positive Input 1 35 28 22 18 16 CMP2_HP2 I CMPSS-2 High Comparator Positive Input 2 48 38 28 24 22 CMP2_HP3 I CMPSS-2 High Comparator Positive Input 3 50 40, 41 29 25 23 CMP2_HP5 I CMPSS-2 High Comparator Positive Input 5 28 35 17 13 11 CMP2_LN0 I CMPSS-2 Low Comparator Negative Input 0 50 40 29 25 23 CMP2_LN1 I CMPSS-2 Low Comparator Negative Input 1 35 28 22 18 16 CMP2_LP0 I CMPSS-2 Low Comparator Positive Input 0 42 36 27 23 21 CMP2_LP1 I CMPSS-2 Low Comparator Positive Input 1 35 28 22 18 16 TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
42 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 5-2. Analog Signals (continued) SIGNAL NAME PIN TYPE DESCRIPTION 128 PDT 100 PZ 80 PNA 64 PM 56 RSH CMP2_LP2 I CMPSS-2 Low Comparator Positive Input 2 48 38 28 24 22 CMP2_LP3 I CMPSS-2 Low Comparator Positive Input 3 50 40, 41 29 25 23 CMP2_LP5 I CMPSS-2 Low Comparator Positive Input 5 28 35 17 13 11 CMP3_HN0 I CMPSS-3 High Comparator Negative Input 0 20 16 12 8 6 CMP3_HN1 I CMPSS-3 High Comparator Negative Input 1 28 21 17 13 11 CMP3_HP0 I CMPSS-3 High Comparator Positive Input 0 19 15 11 7 CMP3_HP1 I CMPSS-3 High Comparator Positive Input 1 28 21 17 13 11 CMP3_HP2 I CMPSS-3 High Comparator Positive Input 2 30 23 19 15 13 CMP3_HP3 I CMPSS-3 High Comparator Positive Input 3 20 16 12 8 6 CMP3_HP4 I CMPSS-3 High Comparator Positive Input 4 26 19 15 11 9 CMP3_HP5 I CMPSS-3 High Comparator Positive Input 5 20 18 12 8 6 CMP3_LN0 I CMPSS-3 Low Comparator Negative Input 0 20 16 12 8 6 CMP3_LN1 I CMPSS-3 Low Comparator Negative Input 1 28 21 17 13 11 CMP3_LP0 I CMPSS-3 Low Comparator Positive Input 0 19 15 11 7 CMP3_LP1 I CMPSS-3 Low Comparator Positive Input 1 28 21 17 13 11 CMP3_LP2 I CMPSS-3 Low Comparator Positive Input 2 30 23 19 15 13 CMP3_LP3 I CMPSS-3 Low Comparator Positive Input 3 20 16 12 8 6 CMP3_LP4 I CMPSS-3 Low Comparator Positive Input 4 26 19 15 11 9 CMP3_LP5 I CMPSS-3 Low Comparator Positive Input 5 20 18 12 8 6 CMP4_HN0 I CMPSS-4 High Comparator Negative Input 0 42 42 27 23 21 CMP4_HN1 I CMPSS-4 High Comparator Negative Input 1 37 31 23 19 17 CMP4_HP0 I CMPSS-4 High Comparator Positive Input 0 49 39 28 24 22 CMP4_HP1 I CMPSS-4 High Comparator Positive Input 1 37 31 23 19 17 CMP4_HP2 I CMPSS-4 High Comparator Positive Input 2 35 29 22 18 16 CMP4_HP3 I CMPSS-4 High Comparator Positive Input 3 42 42 27 23 21 CMP4_HP4 I CMPSS-4 High Comparator Positive Input 4 39 37 24 20 18 CMP4_HP5 I CMPSS-4 High Comparator Positive Input 5 36 30 CMP4_LN0 I CMPSS-4 Low Comparator Negative Input 0 42 42 27 23 21 CMP4_LN1 I CMPSS-4 Low Comparator Negative Input 1 37 31 23 19 17 CMP4_LP0 I CMPSS-4 Low Comparator Positive Input 0 49 39 28 24 22 CMP4_LP1 I CMPSS-4 Low Comparator Positive Input 1 37 31 23 19 17 CMP4_LP2 I CMPSS-4 Low Comparator Positive Input 2 35 29 22 18 16 CMP4_LP3 I CMPSS-4 Low Comparator Positive Input 3 42 42 27 23 21 CMP4_LP4 I CMPSS-4 Low Comparator Positive Input 4 39 37 24 20 18 CMP4_LP5 I CMPSS-4 Low Comparator Positive Input 5 36 30 D0 I ADC-D Input 0 64 52 37 31 28 D1 I ADC-D Input 1 65 53 38 32 29 D2 I ADC-D Input 2 66 54 39 33 30 D3 I ADC-D Input 3 67 55 40 34 31 D4 I ADC-D Input 4 68 56 41 35 32 D5 I ADC-D Input 5 23 D6 I ADC-D Input 6 24 D7 I ADC-D Input 7 25 D8 I ADC-D Input 8 43 www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 43 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 5-2. Analog Signals (continued) SIGNAL NAME PIN TYPE DESCRIPTION 128 PDT 100 PZ 80 PNA 64 PM 56 RSH D9 I ADC-D Input 9 44 D10 I ADC-D Input 10 45 D11 I ADC-D Input 11 29 22 18 14 12 D12 I ADC-D Input 12 37 31 23 19 17 D13 I ADC-D Input 13 33, 34 26, 27 21 17 15 D14 I ADC-D Input 14 18 14 10 6 D15 I ADC-D Input 15 38 32 D16 I ADC-D Input 16 36 30 D18 I ADC-D Input 18 46 D19 I ADC-D Input 19 47 D20 I ADC-D Input 20 31, 32 24, 25 20 16 14 DACA_OUT O Buffered DAC-A Output. 30 23 19 15 13 DACB_OUT O Buffered DAC-B Output. 29 22 18 14 12 E0 I ADC-E Input 0 64 52 37 31 28 E1 I ADC-E Input 1 65 53 38 32 29 E2 I ADC-E Input 2 66 54 39 33 30 E3 I ADC-E Input 3 67 55 40 34 31 E4 I ADC-E Input 4 68 56 41 35 32 E5 I ADC-E Input 5 23 E6 I ADC-E Input 6 24 E7 I ADC-E Input 7 25 E8 I ADC-E Input 8 43 E9 I ADC-E Input 9 44 E10 I ADC-E Input 10 45 E11 I ADC-E Input 11 35 29 22 18 16 E12 I ADC-E Input 12 19 15 11 7 E13 I ADC-E Input 13 33, 34 26, 27 21 17 15 E14 I ADC-E Input 14 18 14 10 6 E15 I ADC-E Input 15 38 32 E16 I ADC-E Input 16 36 30 E18 I ADC-E Input 18 46 E19 I ADC-E Input 19 47 E20 I ADC-E Input 20 31, 32 24, 25 20 16 14 E30 I ADC-E Input 30 37 31 23 19 17 PGA1_INM I PGA-1 Minus 22 18 14 10 8 PGA1_INP I PGA-1 Plus 21 17 13 9 7 PGA1_OUT O PGA-1 Output 26 19 15 11 9 PGA2_INM I PGA-2 Minus 28 21 17 13 11 PGA2_INP I PGA-2 Plus 20 16 12 8 6 PGA2_OUT O PGA-2 Output 27 20 16 12 10 PGA3_INM I PGA-3 Minus 36 30 23 19 17 PGA3_INP I PGA-3 Plus 35 29 22 18 16 PGA3_OUT O PGA-3 Output 38 32 24 20 18 TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
44 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 5-2. Analog Signals (continued) SIGNAL NAME PIN TYPE DESCRIPTION 128 PDT 100 PZ 80 PNA 64 PM 56 RSH VREFHI I ADC High Reference. In external reference mode, externally drive the high reference voltage onto this pin. In internal reference mode, a voltage is driven onto this pin by the device. In either mode, place at least a 2.2-µF capacitor on this pin. This capacitor should be placed as close to the device as possible between the VREFHI and VREFLO pins. 31, 32 24, 25 20 16 14 VREFLO I ADC Low Reference 33, 34 26, 27 21 17 15 www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 45 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
5.3.2 Digital Signals
Table 5-3. Digital Signals SIGNAL NAME PIN TYPE DESCRIPTION GPIO 128 PDT 100 PZ 80 PNA 64 PM 56 RSH ADCE_EXTMUXSEL0 O ADCE external mux selection pin for position 0 20, 228 18, 60 14, 48 10, 33 6, 27 24 ADCE_EXTMUXSEL1 O ADCE external mux selection pin for position 1 21, 226 19, 61 15, 49 11, 34 7, 28 25 ADCE_EXTMUXSEL2 O ADCE external mux selection pin for position 2 242 20 16 12 8 6 ADCE_EXTMUXSEL3 O ADCE external mux selection pin for position 3 224 21 17 13 9 7 ADCSOCAO O ADC Start of Conversion A for External ADC 8, 33, 53, 70, 74, 228 95 12, 14, 53, 74 10, 38, 58 6, 32, 47 29 ADCSOCBO O ADC Start of Conversion B for External ADC 10, 32, 54 17, 79, 122 13, 64, 93 49, 76 40, 63 37 AUXCLKIN I Auxilary Clock Input 29 1 100 3 1 2 CLB_OUTPUTXBAR1 O CLB Output X-BAR Output 1 19, 22 88, 104 69, 83 51, 67 42, 56 39, 51 CLB_OUTPUTXBAR2 O CLB Output X-BAR Output 2 7, 47 8, 105 6, 84 68 57 52 CLB_OUTPUTXBAR3 O CLB Output X-BAR Output 3 23, 42, 44 94, 102, 106 81, 85 57, 65, 69 54 49 CLB_OUTPUTXBAR4 O CLB Output X-BAR Output 4 10, 40, 43, 45 91, 101, 110, 122 80, 93 54, 64, 73, 76 53, 63 48 CLB_OUTPUTXBAR5 O CLB Output X-BAR Output 5 5, 8, 52 15, 95, 118 11, 74, 89 58, 74 47, 61 55 CLB_OUTPUTXBAR6 O CLB Output X-BAR Output 6 4, 15, 53 16, 96, 124 12, 75, 95 59, 78 48 43 CLB_OUTPUTXBAR7 O CLB Output X-BAR Output 7 1, 14, 56 80, 99, 125 65, 78, 96 62, 79 51 46 CLB_OUTPUTXBAR8 O CLB Output X-BAR Output 8 0, 6, 57, 80 81, 100, 116, 126 66, 79, 97 63, 80 52, 64 1, 47 EPWM1_A O ePWM-1 Output A 0, 4, 30, 77, 80, 224 21, 96, 100, 113, 116, 127 17, 75, 79, 98 1, 13, 59, 9, 48, 7, 43, EPWM1_B O ePWM-1 Output B 1, 5, 31, 75, 81, 226 19, 99, 111, 117, 118, 128 15, 78, 89, 99 2, 11, 62, 7, 51, 61 46, 55 EPWM2_A O ePWM-2 Output A 2, 6, 7, 41, 79, 230 50, 98, 103, 105, 115, 126 40, 77, 82, 84, 29, 61, 66, 68, 80 25, 50, 55, 57, 1, 23, 45, 50, EPWM2_B O ePWM-2 Output B 3, 7, 40, 74, 78, 227, 228 18, 48, 86, 97, 101, 105, 114 14, 38, 76, 80, 10, 28, 60, 64, 68 6, 24, 49, 53, 22, 44, 48, 52 EPWM3_A O ePWM-3 Output A 0, 4, 14, 68, 78, 80, 227 48, 72, 96, 100, 114, 116, 125 38, 75, 79, 96 28, 59, 63, 24, 48, 22, 43, EPWM3_B O ePWM-3 Output B 1, 5, 15, 69, 79, 230 50, 73, 99, 115, 118, 124 40, 78, 89, 95 29, 62, 74, 25, 51, 23, 46, EPWM4_A O ePWM-4 Output A 2, 6, 22, 76, 242 20, 98, 104, 112, 126 16, 77, 83, 97 12, 61, 67, 8, 50, 56, 64 1, 6, 45, 51 EPWM4_B O ePWM-4 Output B 3, 7, 23, 71 83, 97, 102, 105 76, 81, 84 60, 65, 68 49, 54, 44, 49, EPWM5_A O ePWM-5 Output A 8, 37, 72 76, 84, 95 61, 74 46, 58 37, 47 34 EPWM5_B O ePWM-5 Output B 9, 35, 73 78, 85, 119 63, 90 48, 75 39, 62 36, 56 EPWM6_A O ePWM-6 Output A 10, 17, 18, 72, 75, 226 19, 67, 84, 87, 111, 122 15, 55, 68, 93 11, 40, 50, 7, 34, 41, 63 31, 38 EPWM6_B O ePWM-6 Output B 11, 19, 69 64, 73, 88 52, 69 37, 51 31, 42 28, 39 EPWM7_A O ePWM-7 Output A 12, 28, 41, 64, 68, 236 2, 49, 56, 63, 72, 103 1, 39, 51, 82 4, 28, 36, 2, 24, 30, 55 3, 22, 27, 50 EPWM7_B O ePWM-7 Output B 13, 29, 67, 215 1, 10, 47, 62 50, 100 3, 35 1, 29 2, 26 EPWM8_A O ePWM-8 Output A 14, 24, 73, 78 68, 85, 114, 125 56, 96 41, 79 35 32 EPWM8_B O ePWM-8 Output B 15, 32, 79 79, 115, 124 64, 95 49, 78 40 37 EPWM9_A O ePWM-9 Output A 16, 24, 71, 73 66, 68, 83, 85 54, 56 39, 41 33, 35 30, 32 EPWM9_B O ePWM-9 Output B 17, 72 67, 84 55 40 34 31 EPWM10_A O ePWM-10 Output A 2, 62, 211, 228 18, 43, 58, 98 14, 46, 77 10, 31, 61 6, 50 45 EPWM10_B O ePWM-10 Output B 1, 63, 212, 226 19, 44, 59, 99 15, 47, 78 11, 32, 62 7, 51 46 EPWM11_A O ePWM-11 Output A 8, 64, 213, 242 20, 45, 56, 95 16, 74 12, 58 8, 47 6 EPWM11_B O ePWM-11 Output B 4, 65, 214, 224 21, 46, 57, 96 17, 75 13, 59 9, 48 7, 43 EPWM12_A O ePWM-12 Output A 20, 23, 66, 236, 253 9, 49, 60, 102 39, 41, 48, 81 28, 33, 65 24, 27, 22, 24, EPWM12_B O ePWM-12 Output B 21, 41, 60, 67, 247 10, 52, 61, 103 42, 44, 49, 82 34, 66 28, 55 25, 50 EQEP1_A I eQEP-1 Input A 6, 10, 20, 25, 28, 64, 65, 77, 224 69, 78, 80, 101, 106, 113, 122, 126 1, 9, 17, 48, 57, 63, 65, 80, 85, 93, 97 4, 13, 33, 42, 48, 64, 69, 76, 80 2, 9, 27, 39, 53, 63, 64 1, 3, 7, 24, 36, EQEP1_B I eQEP-1 Input B 7, 11, 21, 29, 37, 74, 228 73, 76, 81, 86, 103, 105 10, 14, 49, 52, 61, 66, 82, 84, 100 3, 10, 34, 37, 46, 66, 1, 6, 28, 31, 37, 55, 57 2, 25, 28, 34, 50, 52 TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
46 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 5-3. Digital Signals (continued) SIGNAL NAME PIN TYPE DESCRIPTION GPIO 128 PDT 100 PZ 80 PNA 64 PM 56 RSH EQEP1_INDEX I/O eQEP-1 Index 72, 76, 80, 236, 242 67, 79, 84, 91, 100, 102, 112, 116, 119, 121, 128 12, 16, 39, 50, 55, 64, 79, 81, 90, 92, 99 2, 12, 28, 35, 40, 49, 54, 63, 65, 8, 24, 29, 34, 40, 52, 54, 62 6, 22, 26, 31, 37, 47, 49, 56 EQEP1_STROBE I/O eQEP-1 Strobe 75, 226 104, 111, 127 11, 15, 51, 54, 67, 74, 78, 83, 1, 11, 36, 39, 57, 58, 62, 67 7, 30, 33, 47, 51, 56 27, 30, 46, 51 EQEP2_A I eQEP-2 Input A 11, 14, 18, 24, 54, 69, 215 87, 125 13, 52, 56, 68, 37, 41, 50, 31, 35, 28, 32, EQEP2_B I eQEP-2 Input B 15, 16, 19, 25, 33, 55, 70 88, 124 43, 53, 54, 57, 69, 95 38, 39, 42, 51, 78 32, 33, 29, 30, EQEP2_INDEX I/O eQEP-2 Index 26, 29, 57, 71 1, 70, 81, 83 58, 66, 100 3, 43 1 2 EQEP2_STROBE I/O eQEP-2 Strobe 4, 27, 28, 56, 64 2, 56, 71, 80, 96 1, 59, 65, 75 4, 44, 59 2, 48 3, 43 EQEP3_A I eQEP-3 Input A 22, 25, 70, 211 43, 69, 74, 104 57, 83 42, 67 56 51 EQEP3_B I eQEP-3 Input B 9, 26, 72, 212 44, 70, 84, 119 58, 90 43, 75 62 56 EQEP3_INDEX I/O eQEP-3 Index 11, 18, 30, 69, 81, 214 46, 64, 73, 87, 117, 127 52, 68, 98 1, 37, 50 31, 41 28, 38 EQEP3_STROBE I/O eQEP-3 Strobe 10, 16, 27, 40, 71, 213 45, 66, 71, 83, 101, 122 54, 59, 80, 93 39, 44, 64, 33, 53, 63 30, 48 ERRORSTS O Error Status Output. This signal requires an external pulldown. 73 1, 2, 51, 56, 68, 85 1, 43, 56, 100 3, 4, 41 1, 2, 35 2, 3, 32 FSIRXA_CLK I FSIRX-A Input Clock 0, 4, 13, 30, 33, 54, 57, 67, 70 81, 96, 100, 127 13, 50, 53, 66, 75, 79, 98 1, 35, 38, 59, 63 29, 32, 48, 52 26, 29, 43, 47 FSIRXA_D0 I FSIRX-A Primary Data Input 3, 12, 32, 40, 44, 52, 58, 68 97, 101, 106 11, 51, 64, 67, 76, 80, 85 36, 49, 60, 64, 69 30, 40, 49, 53 27, 37, 44, 48 FSIRXA_D1 I FSIRX-A Optional Additional Data Input 2, 11, 31, 41, 53, 56, 69 103, 128 12, 52, 65, 77, 82, 99 2, 37, 61, 31, 50, 28, 45, FSITXA_CLK O FSITX-A Output Clock 7, 10, 27, 44, 51, 78 14, 71, 105, 106, 114, 122 10, 59, 84, 85, 44, 68, 69, 76 57, 63 52 FSITXA_D0 O FSITX-A Primary Data Output 6, 9, 26, 45, 49, 80 12, 70, 110, 116, 119, 126 8, 58, 90, 97 43, 73, 75, 80 62, 64 1, 56 FSITXA_D1 O FSITX-A Optional Additional Data Output 5, 6, 8, 25, 46, 50, 118, 126 9, 57, 74, 89, 6, 42, 58, 74, 80 47, 61, 64 1, 55 GPIO0 I/O General-Purpose Input Output 0 0 100 79 63 52 47 GPIO1 I/O General-Purpose Input Output 1 1 99 78 62 51 46 GPIO2 I/O General-Purpose Input Output 2 2 98 77 61 50 45 GPIO3 I/O General-Purpose Input Output 3 3 97 76 60 49 44 GPIO4 I/O General-Purpose Input Output 4 4 96 75 59 48 43 GPIO5 I/O General-Purpose Input Output 5 5 118 89 74 61 55 GPIO6 I/O General-Purpose Input Output 6 6 126 97 80 64 1 GPIO7 I/O General-Purpose Input Output 7 7 105 84 68 57 52 GPIO8 I/O General-Purpose Input Output 8 8 95 74 58 47 GPIO9 I/O General-Purpose Input Output 9 9 119 90 75 62 56 GPIO10 I/O General-Purpose Input Output 10 10 122 93 76 63 GPIO11 I/O General-Purpose Input Output 11 11 64 52 37 31 28 GPIO12 I/O General-Purpose Input Output 12 12 63 51 36 30 27 GPIO13 I/O General-Purpose Input Output 13 13 62 50 35 29 26 GPIO14 I/O General-Purpose Input Output 14 14 125 96 79 GPIO15 I/O General-Purpose Input Output 15 15 124 95 78 GPIO16 I/O General-Purpose Input Output 16 16 66 54 39 33 30 GPIO17 I/O General-Purpose Input Output 17 17 67 55 40 34 31 GPIO18 I/O General-Purpose Input Output 18 18 87 68 50 41 38 GPIO19 I/O General-Purpose Input Output 19 19 88 69 51 42 39 GPIO20 I/O General-Purpose Input Output 20 20 60 48 33 27 24 GPIO21 I/O General-Purpose Input Output 21 21 61 49 34 28 25 GPIO22 I/O General-Purpose Input Output 22 22 104 83 67 56 51 GPIO23 I/O General-Purpose Input Output 23 23 102 81 65 54 49 GPIO24 I/O General-Purpose Input Output 24 24 68 56 41 35 32 GPIO25 I/O General-Purpose Input Output 25 25 69 57 42 GPIO26 I/O General-Purpose Input Output 26 26 70 58 43 www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 47 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 5-3. Digital Signals (continued) SIGNAL NAME PIN TYPE DESCRIPTION GPIO 128 PDT 100 PZ 80 PNA 64 PM 56 RSH GPIO27 I/O General-Purpose Input Output 27 27 71 59 44 GPIO28 I/O General-Purpose Input Output 28 28 2 1 4 2 3 GPIO29 I/O General-Purpose Input Output 29 29 1 100 3 1 2 GPIO30 I/O General-Purpose Input Output 30 30 127 98 1 GPIO31 I/O General-Purpose Input Output 31 31 128 99 2 GPIO32 I/O General-Purpose Input Output 32 32 79 64 49 40 37 GPIO33 I/O General-Purpose Input Output 33 33 65 53 38 32 29 GPIO34 I/O General-Purpose Input Output 34 34 123 94 77 GPIO35 I/O General-Purpose Input Output 35 35 78 63 48 39 36 GPIO37 I/O General-Purpose Input Output 37 37 76 61 46 37 34 GPIO40 I/O General-Purpose Input Output 40 40 101 80 64 53 48 GPIO41 I/O General-Purpose Input Output 41 41 103 82 66 55 50 GPIO42 I/O General-Purpose Input Output 42 42 94 57 GPIO43 I/O General-Purpose Input Output 43 43 91 54 GPIO44 I/O General-Purpose Input Output 44 44 106 85 69 GPIO45 I/O General-Purpose Input Output 45 45 110 73 GPIO46 I/O General-Purpose Input Output 46 46 4 6 GPIO47 I/O General-Purpose Input Output 47 47 8 6 GPIO48 I/O General-Purpose Input Output 48 48 11 7 GPIO49 I/O General-Purpose Input Output 49 49 12 8 GPIO50 I/O General-Purpose Input Output 50 50 13 9 GPIO51 I/O General-Purpose Input Output 51 51 14 10 GPIO52 I/O General-Purpose Input Output 52 52 15 11 GPIO53 I/O General-Purpose Input Output 53 53 16 12 GPIO54 I/O General-Purpose Input Output 54 54 17 13 GPIO55 I/O General-Purpose Input Output 55 55 51 43 GPIO56 I/O General-Purpose Input Output 56 56 80 65 GPIO57 I/O General-Purpose Input Output 57 57 81 66 GPIO58 I/O General-Purpose Input Output 58 58 82 67 GPIO59 I/O General-Purpose Input Output 59 59 121 92 GPIO60 I/O General-Purpose Input Output 60 60 52 44 GPIO61 I/O General-Purpose Input Output 61 61 120 91 GPIO62 I/O General-Purpose Input Output 62 62 58 46 31 GPIO63 I/O General-Purpose Input Output 63 63 59 47 32 GPIO64 I/O General-Purpose Input Output 64 64 56 GPIO65 I/O General-Purpose Input Output 65 65 57 GPIO66 I/O General-Purpose Input Output 66 66 9 GPIO67 I/O General-Purpose Input Output 67 67 10 GPIO68 I/O General-Purpose Input Output 68 68 72 GPIO69 I/O General-Purpose Input Output 69 69 73 GPIO70 I/O General-Purpose Input Output 70 70 74 GPIO71 I/O General-Purpose Input Output 71 71 83 GPIO72 I/O General-Purpose Input Output 72 72 84 GPIO73 I/O General-Purpose Input Output 73 73 85 GPIO74 I/O General-Purpose Input Output 74 74 86 GPIO75 I/O General-Purpose Input Output 75 75 111 GPIO76 I/O General-Purpose Input Output 76 76 112 GPIO77 I/O General-Purpose Input Output 77 77 113 GPIO78 I/O General-Purpose Input Output 78 78 114 GPIO79 I/O General-Purpose Input Output 79 79 115 GPIO80 I/O General-Purpose Input Output 80 80 116 GPIO81 I/O General-Purpose Input Output 81 81 117 GPIO211 I/O General-Purpose Input Output 211 211 43 GPIO212 I/O General-Purpose Input Output 212 212 44 TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
48 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 5-3. Digital Signals (continued) SIGNAL NAME PIN TYPE DESCRIPTION GPIO 128 PDT 100 PZ 80 PNA 64 PM 56 RSH GPIO213 I/O General-Purpose Input Output 213 213 45 GPIO214 I/O General-Purpose Input Output 214 214 46 GPIO215 I/O General-Purpose Input Output 215 215 47 GPIO224 I/O General-Purpose Input Output 224 224 21 17 13 9 7 GPIO226 I/O General-Purpose Input Output 226 226 19 15 11 7 GPIO227 I/O General-Purpose Input Output 227 227 48 38 28 24 22 GPIO228 I/O General-Purpose Input Output 228 228 18 14 10 6 GPIO230 I/O General-Purpose Input Output 230 230 50 40 29 25 23 GPIO236 I/O General-Purpose Input Output 236 236 49 39 28 24 22 GPIO242 I/O General-Purpose Input Output 242 242 20 16 12 8 6 GPIO247 I/O General-Purpose Input Output 247 247 42 GPIO253 I/O General-Purpose Input Output 253 253 41 I2CA_SCL I/OD I2C-A Open-Drain Bidirectional Clock 65, 70 96, 99, 119 48, 53, 59, 61, 66, 68, 74, 75, 78, 90 33, 38, 44, 46, 50, 54, 58, 59, 62, 27, 32, 37, 41, 47, 48, 51, 62 24, 29, 34, 38, 43, 46, I2CA_SDA I/OD I2C-A Open-Drain Bidirectional Data 79, 230 80, 88, 94, 100, 115, 118, 122 40, 49, 58, 63, 64, 65, 69, 79, 89, 93 29, 34, 43, 48, 49, 51, 57, 63, 74, 25, 28, 39, 40, 42, 52, 61, 63 23, 25, 36, 37, 39, 47, I2CB_SCL I/OD I2C-B Open-Drain Bidirectional Clock 3, 9, 15, 29, 51, 81, 227 119, 124 10, 38, 76, 90, 95, 100 3, 28, 60, 75, 78 1, 24, 49, 62 2, 22, 44, 56 I2CB_SDA I/OD I2C-B Open-Drain Bidirectional Data 2, 14, 28, 34, 50, 64, 80, 230 2, 13, 50, 56, 98, 116, 123, 125 1, 9, 40, 77, 94, 96 4, 29, 61, 77, 79 2, 25, 3, 23, LINA_RX I LIN-A Receive 9, 11, 13, 15, 19, 226 74, 78, 88, 94, 102, 103, 111, 119, 121, 124 6, 8, 15, 43, 47, 50, 52, 53, 63, 69, 81, 82, 90, 92, 95, 100 3, 11, 32, 35, 37, 38, 48, 51, 57, 65, 66, 75, 1, 7, 29, 31, 32, 39, 42, 54, 55, 2, 26, 28, 29, 36, 39, 49, 50, LINA_TX O LIN-A Transmit 68, 73 87, 101, 104, 106, 122, 125 1, 13, 51, 56, 61, 64, 67, 68, 80, 83, 85, 93, 4, 6, 36, 41, 46, 49, 50, 64, 67, 69, 76, 79 2, 30, 35, 37, 40, 41, 53, 56, 3, 27, 32, 34, 37, 38, 48, 51 MCANA_RX I CAN/CAN FD Receive 79, 80, 230, 242 8, 9, 12, 14, 20, 72, 74, 81, 100, 112, 115, 116, 118, 120, 127 6, 8, 10, 16, 40, 47, 49, 51, 52, 66, 79, 89, 91, 98 1, 12, 29, 32, 34, 36, 37, 63, 74 8, 25, 28, 30, 31, 52, 6, 23, 25, 27, 28, 47, MCANA_TX O CAN/CAN FD Transmit 74, 77, 81, 224, 228 99, 105, 113, 117, 128 7, 9, 14, 17, 44, 46, 48, 50, 55, 65, 75, 78, 84, 99 2, 6, 10, 13, 31, 33, 35, 40, 59, 62, 68 6, 9, 27, 29, 34, 48, 51, 7, 24, 26, 31, 43, 46, MCANB_RX I CAN/CAN FD Receive 3, 18, 33, 35, 53, 59, 61 120, 121 12, 53, 63, 68, 76, 91, 92 38, 48, 50, 32, 39, 41, 49 29, 36, 38, 44 MCANB_TX O CAN/CAN FD Transmit 2, 19, 32, 37, 58 76, 79, 82, 88, 98 61, 64, 67, 69, 46, 49, 51, 37, 40, 42, 50 34, 37, 39, 45 OUTPUTXBAR1 O Output X-BAR Output 1 2, 24, 34, 58, 73, 78, 227 114, 123 38, 56, 67, 77, 28, 41, 61, 24, 35, 22, 32, OUTPUTXBAR2 O Output X-BAR Output 2 3, 25, 37, 54, 59, 76, 242 112, 121 13, 16, 57, 61, 76, 92 12, 42, 46, 8, 37, 6, 34, OUTPUTXBAR3 O Output X-BAR Output 3 4, 5, 14, 26, 48, 55, 60, 62, 77, 224 70, 96, 113, 118, 125 7, 17, 43, 44, 46, 58, 75, 89, 13, 31, 43, 59, 74, 79 9, 48, 7, 43, OUTPUTXBAR4 O Output X-BAR Output 4 6, 15, 27, 33, 49, 61, 63, 70 120, 124, 126 8, 47, 53, 59, 91, 95, 97 32, 38, 44, 78, 80 32, 64 1, 29 OUTPUTXBAR5 O Output X-BAR Output 5 7, 28, 42, 64 2, 56, 94, 105 1, 84 4, 57, 68 2, 57 3, 52 OUTPUTXBAR6 O Output X-BAR Output 6 9, 29, 43, 81 1, 91, 117, 119 90, 100 3, 54, 75 1, 62 2, 56 OUTPUTXBAR7 O Output X-BAR Output 7 0, 11, 16, 30, 44, 69, 71, 80 64, 66, 73, 83, 100, 106, 116, 127 52, 54, 79, 85, 1, 37, 39, 63, 69 31, 33, 28, 30, OUTPUTXBAR8 O Output X-BAR Output 8 17, 31, 45, 72 67, 84, 110, 128 55, 99 2, 40, 73 34 31 PMBUSA_ALERT I/OD PMBus-A Open-Drain Bidirectional Alert Signal 13, 19, 27, 37, 43, 45, 67 91, 110 50, 59, 61, 69 35, 44, 46, 51, 54, 73 29, 37, 26, 34, PMBUSA_CTL I/O PMBus-A Control Signal - Target Input/Controller Output 44, 68 94, 106 51, 58, 63, 68, 36, 43, 48, 50, 57, 69 30, 39, 27, 36, www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 49 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 5-3. Digital Signals (continued) SIGNAL NAME PIN TYPE DESCRIPTION GPIO 128 PDT 100 PZ 80 PNA 64 PM 56 RSH PMBUSA_SCL I/OD PMBus-A Open-Drain Bidirectional Clock 230 8, 50, 66, 68, 78, 83, 85, 97, 103, 115, 119, 124 6, 40, 54, 56, 63, 76, 82, 90, 29, 39, 41, 48, 60, 66, 75, 78 25, 33, 35, 39, 49, 55, 23, 30, 32, 36, 44, 50, PMBUSA_SDA I/OD PMBus-A Open-Drain Bidirectional Data 2, 14, 17, 25, 32, 62, 72 4, 11, 58, 67, 69, 79, 84, 98, 101, 106, 123, 125 7, 46, 55, 57, 64, 77, 80, 85, 94, 96 6, 31, 40, 42, 49, 61, 64, 69, 77, 34, 40, 50, 53 31, 37, 45, 48 SCIA_RX I SCI-A Receive Data 72, 80 78, 84, 97, 100, 116, 118, 119 1, 8, 47, 55, 57, 63, 76, 79, 89, 90 4, 32, 40, 42, 48, 60, 63, 74, 75 2, 34, 39, 49, 52, 61, 3, 31, 36, 44, 47, 55, SCIA_TX O SCI-A Transmit Data 105 7, 46, 54, 56, 61, 74, 77, 78, 84, 100 3, 31, 39, 41, 46, 58, 61, 62, 68 1, 33, 35, 37, 47, 50, 51, 57 2, 30, 32, 34, 45, 46, SCIB_RX I SCI-B Receive Data 11, 13, 15, 19, 23, 41, 57, 67, 69 88, 102, 103, 124 50, 52, 66, 69, 81, 82, 95 35, 37, 51, 65, 66, 78 29, 31, 42, 54, 26, 28, 39, 49, SCIB_TX O SCI-B Transmit Data 9, 10, 12, 14, 18, 22, 40, 56, 68 63, 72, 80, 87, 101, 104, 119, 122, 125 51, 65, 68, 80, 83, 90, 93, 96 36, 50, 64, 67, 75, 76, 30, 41, 53, 56, 62, 63 27, 38, 48, 51, SCIC_RX I SCI-C Receive Data 21, 33, 42, 67, 75, 81, 226 111, 117 15, 49, 53 11, 34, 38, 7, 28, 32 25, 29 SCIC_TX O SCI-C Transmit Data 20, 43, 68, 77, 224 21, 60, 72, 91, 113 17, 48 13, 33, 54 9, 27 7, 24 SPIA_CLK I/O SPI-A Clock 3, 9, 12, 18, 56, 68, 75, 226 97, 111, 119 15, 51, 65, 68, 76, 90 11, 36, 50, 60, 75 7, 30, 41, 49, 27, 38, 44, 56 SPIA_PICO I/O SPI-A Peripheral In, Controller Out (PICO) 2, 8, 11, 16, 54, 69, 71, 77, 224 83, 95, 98, 113 13, 17, 52, 54, 74, 77 13, 37, 39, 58, 61 9, 31, 33, 47, 7, 28, 30, 45 SPIA_POCI I/O SPI-A Peripheral Out, Controller In (POCI) 1, 4, 10, 13, 17, 35, 55, 67, 72, 74, 228 122 14, 43, 50, 55, 63, 75, 78, 93 10, 35, 40, 48, 59, 62, 6, 29, 34, 39, 48, 51, 26, 31, 36, 43, SPIA_PTE I/O SPI-A Peripheral Transmit Enable (PTE) 242 81, 85, 88, 100, 112, 116, 118 16, 52, 56, 61, 66, 69, 79, 89 12, 37, 41, 46, 51, 63, 8, 31, 35, 37, 42, 52, 6, 28, 32, 34, 39, 47, SPIB_CLK I/O SPI-B Clock 4, 14, 22, 26, 28, 32, 52, 58, 64, 81 96, 104, 117, 125 1, 11, 58, 64, 67, 75, 83, 96 4, 43, 49, 59, 67, 79 2, 40, 48, 56 3, 37, 43, 51 SPIB_PICO I/O SPI-B Peripheral In, Controller Out (PICO) 7, 20, 24, 30, 40, 50, 56, 60, 65, 73 80, 85, 101, 105, 127 9, 44, 48, 56, 65, 80, 84, 98 1, 33, 41, 64, 68 27, 35, 53, 57 24, 32, 48, 52 SPIB_POCI I/O SPI-B Peripheral Out, Controller In (POCI) 6, 16, 21, 25, 31, 83, 103, 120, 126, 128 10, 49, 54, 57, 66, 82, 91, 97, 2, 34, 39, 42, 66, 80 28, 33, 55, 64 1, 25, 30, 50 SPIB_PTE I/O SPI-B Peripheral Transmit Enable (PTE) 15, 23, 27, 29, 33, 53, 59, 70 1, 16, 65, 71, 74, 102, 121, 124 12, 53, 59, 81, 92, 95, 100 3, 38, 44, 65, 78 1, 32, 2, 29, SYNCOUT O External ePWM Synchronization Pulse 6, 52 15, 126 11, 97 80 64 1 TDI I JTAG Test Data Input (TDI) - TDI is the default mux selection for the pin. The internal pullup is disabled by default. The internal pullup should be enabled or an external pullup added on the board if this pin is used as JTAG TDI to avoid a floating input. 35 78 63 48 39 36 TDO O JTAG Test Data Output (TDO) - TDO is the default mux selection for the pin. The internal pullup is disabled by default. The TDO function will be in a tri- state condition when there is no JTAG activity, leaving this pin floating; the internal pullup should be enabled or an external pullup added on the board to avoid a floating GPIO input. 37 76 61 46 37 34 USB0DM O USB-0 PHY differential data 23 102 81 65 54 49 USB0DP O USB-0 PHY differential data 41 103 82 66 55 50 X1 I/O Crystal oscillator input or single-ended clock input. The device initialization software must configure this pin before the crystal oscillator is enabled. To use this oscillator, a quartz crystal circuit must be connected to X1 and X2. This pin can also be used to feed a single-ended 3.3-V level clock. 19 88 69 51 42 39 X2 I/O Crystal oscillator output. 18 87 68 50 41 38 TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
50 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 5-3. Digital Signals (continued) SIGNAL NAME PIN TYPE DESCRIPTION GPIO 128 PDT 100 PZ 80 PNA 64 PM 56 RSH XCLKOUT O External Clock Output. This pin outputs a divided- down version of a chosen clock signal from within the device. 16, 18, 71 66, 83, 87 54, 68 39, 50 33, 41 30, 38
5.3.3 Power and Ground
Table 5-4. Power and Ground SIGNAL NAME PIN TYPE DESCRIPTION 128 PDT 100 PZ 80 PNA 64 PM 56 RSH VDD 1.2-V Digital Logic Power Pins. TI recommends placing a decoupling capacitor near each VDD pin with a minimum total capacitance of approximately 10 µF. It is also recommended that all VDD pins be externally connected to each other when internal VREG is used. 6, 54, 90, 108 4, 71, 87 8, 53, 71 4, 44, 59 5, 41, 53 VDDA 3.3-V Analog Power Pins. Place a minimum 2.2-µF decoupling capacitor on each pin. 41 34 26 22 20 VDDIO 3.3-V Digital I/O Power Pins. Place a minimum 0.1-µF decoupling capacitor on each pin. 5, 55, 89, 109 3, 70, 88 7, 52, 72 43, 60 40, 54 VREGENZ I Internal voltage regulator enable with internal pulldown. Tie low to VSS to enable internal VREG. Tie high to VDDIO to use an external supply. 93 73 56 46 42 VSS Digital Ground 7, 53, 92, 107 5, 45, 72, 86 9, 30, 55, 70 5, 26, 45, 58 PAD VSSA Analog Ground 40 33 25 21 19
5.3.4 Test, JTAG, and Reset
Table 5-5. Test, JTAG, and Reset SIGNAL NAME PIN TYPE DESCRIPTION 128 PDT 100 PZ 80 PNA 64 PM 56 RSH TCK I JTAG test clock with internal pullup. 75 60 45 36 33 TMS I/O JTAG test-mode select (TMS) with internal pullup. This serial control input is clocked into the TAP controller on the rising edge of TCK. This device does not have a TRSTn pin. An external pullup resistor (recommended 2.2 kΩ) on the TMS pin to VDDIO should be placed on the board to keep JTAG in reset during normal operation. 77 62 47 38 35 XRSn I/OD Device Reset (in) and Watchdog Reset (out). During a power-on condition, this pin is driven low by the device. An external circuit may also drive this pin to assert a device reset. This pin is also driven low by the MCU when a watchdog reset occurs. During watchdog reset, the XRSn pin is driven low for the watchdog reset duration of 512 OSCCLK cycles. A resistor between 2.2 kΩ and 10 kΩ should be placed between XRSn and VDDIO. If a capacitor is placed between XRSn and VSS for noise filtering, it should be 100 nF or smaller. These values will allow the watchdog to properly drive the XRSn pin to VOL within 512 OSCCLK cycles when the watchdog reset is asserted. This pin is an open-drain output with an internal pullup. If this pin is driven by an external device, it should be done using an open- drain device. 3 2 5 3 4 www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 51 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
5.4 Pin Multiplexing
5.4.1 GPIO Muxed Pins
Table 5-6. GPIO Muxed Pins 0, 4, 8, 12 1 2 3 5 6 7 9 10 11 13 14 15 ALT GPIO EPWM1_ A OUTPUT XBAR7 SCIA_RX I2CA_SD A SPIA_PTE FSIRXA_ CLK MCANA_RX CLB_OUTP UTXBAR8 EQEP1_IND EX EPWM3_A GPIO EPWM1_ B SCIA_TX I2CA_SCL SPIA_POCI EQEP1_S TROBE MCANA_TX CLB_OUTP UTXBAR7 EPWM10_B EPWM3_B GPIO EPWM2_ A OUTPUTXB AR1 PMBUSA_ SDA SPIA_PICO SCIA_TX FSIRXA_D1 I2CB_SDA EPWM10_A MCANB_TX EPWM4_A GPIO EPWM2_ B OUTPUTXB AR2 OUTPUTXB AR2 PMBUSA_ SCL SPIA_CLK SCIA_RX FSIRXA_D0 I2CB_SCL MCANB_RX EPWM4_B GPIO EPWM3_ A I2CA_SCL MCANA_ TX OUTPUTXB AR3 SPIB_CLK EQEP2_S TROBE FSIRXA_CL K CLB_OUTP UTXBAR6 EPWM11_B SPIA_POCI EPWM1_A GPIO EPWM3_ B I2CA_SDA OUTPUT XBAR3 MCANA_RX SPIA_PTE FSITXA_D CLB_OUTP UTXBAR5 SCIA_RX EPWM1_B GPIO EPWM4_ A OUTPUTXB AR4 SYNCOU T EQEP1_A SPIB_POCI FSITXA_D
0 FSITXA_D1 CLB_OUTP
UTXBAR8 EPWM2_A GPIO EPWM4_ B EPWM2_A OUTPUT XBAR5 EQEP1_B SPIB_PICO FSITXA_C LK CLB_OUTP UTXBAR2 SCIA_TX MCANA_TX EPWM2_B GPIO EPWM5_ A ADCSOC AO EQEP1_STR OBE SCIA_TX SPIA_PICO I2CA_SCL FSITXA_D1 CLB_OUTP UTXBAR5 EPWM11_A GPIO EPWM5_ B SCIB_TX OUTPUT XBAR6 EQEP1_IND EX SCIA_RX SPIA_CLK I2CA_SCL FSITXA_D0 LINA_RX PMBUSA_S CL I2CB_SCL EQEP3_B GPIO EPWM6_ A ADCSOC BO EQEP1_A SCIB_TX SPIA_POCI I2CA_SD A FSITXA_CL K LINA_TX EQEP3_STR OBE CLB_OUTP UTXBAR4 GPIO EPWM6_ B MCANA_RX OUTPUT XBAR7 EQEP1_B SCIB_RX SPIA_PTE FSIRXA_ D1 LINA_RX EQEP2_A SPIA_PICO EQEP3_IND EX GPIO EPWM7_ A MCANA_ RX EQEP1_STR OBE SCIB_TX PMBUSA_C TL FSIRXA_ D0 LINA_TX SPIA_CLK GPIO EPWM7_ B MCANA_ TX EQEP1_IND EX SCIB_RX PMBUSA_A LERT FSIRXA_ CLK LINA_RX SPIA_POCI GPIO EPWM8_ A SCIB_TX I2CB_SDA OUTPUTX BAR3 PMBUSA_S DA SPIB_CLK EQEP2_A LINA_TX EPWM3_A CLB_OUTP UTXBAR7 GPIO EPWM8_ B SCIB_RX I2CB_SCL OUTPUTX BAR4 PMBUSA_S CL SPIB_PTE EQEP2_B LINA_RX EPWM3_B CLB_OUTP UTXBAR6 GPIO SPIA_PIC O OUTPUT XBAR7 EPWM9_A SCIA_TX EQEP1_S TROBE PMBUSA_S CL XCLKOUT EQEP2_B SPIB_POCI EQEP3_STR OBE GPIO SPIA_PO CI OUTPUT XBAR8 EPWM9_B SCIA_RX EQEP1_I NDEX PMBUSA_S DA MCANA_TX EPWM6_A GPIO
18 SPIA_CLK SCIB_TX MCANB_
RX EPWM6_A I2CA_SCL EQEP2_A PMBUSA_C TL XCLKOUT LINA_TX EQEP3_IND EX X2 GPIO
19 SPIA_PTE SCIB_RX MCANB_
TX EPWM6_B I2CA_SD A EQEP2_B PMBUSA_A LERT CLB_OUTP UTXBAR1 LINA_RX X1 GPIO
20 EQEP1_A EPWM12_A SPIB_PIC
O MCANA_T X ADCE_EXT MUXSEL0 I2CA_SCL SCIC_TX GPIO
21 EQEP1_B EPWM12_B SPIB_PO
MCANA_ RX ADCE_EXT MUXSEL1 I2CA_SDA SCIC_RX GPIO EQEP1_S TROBE SCIB_TX SPIB_CLK LINA_TX CLB_OUTP UTXBAR1 LINA_TX EPWM4_A EQEP3_A GPIO EQEP1_I NDEX SCIB_RX SPIB_PTE LINA_RX CLB_OUTP UTXBAR3 LINA_RX EPWM12_A EPWM4_B USB0 DM GPIO OUTPUTX BAR1 EQEP2_A SPIA_PT E EPWM8_A SPIB_PIC O LINA_TX PMBUSA_S CL SCIA_TX ERRORSTS EPWM9_A GPIO OUTPUTX BAR2 EQEP2_B EQEP1_A SPIB_PO CI FSITXA_D PMBUSA_S DA SCIA_RX EQEP3_A GPIO OUTPUTX BAR3 EQEP2_IND EX OUTPUTXB AR3 SPIB_CLK FSITXA_D PMBUSA_C TL I2CA_SDA EQEP3_B GPIO OUTPUTX BAR4 EQEP2_STR OBE OUTPUTXB AR4 SPIB_PTE FSITXA_C LK PMBUSA_A LERT I2CA_SCL EQEP3_STR OBE GPIO
28 SCIA_RX EPWM7_
A OUTPUTXB AR5 EQEP1_A EQEP2_S TROBE LINA_TX SPIB_CLK ERRORSTS I2CB_SDA GPIO
29 SCIA_TX EPWM7_
B OUTPUTXB AR6 EQEP1_B EQEP2_I NDEX LINA_RX SPIB_PTE ERRORSTS I2CB_SCL AUXC LKIN GPIO SPIB_PI CO OUTPUTXB AR7 EQEP1_S TROBE FSIRXA_ CLK MCANA_RX EPWM1_A EQEP3_IND EX TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
52 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 5-6. GPIO Muxed Pins (continued) 0, 4, 8, 12 1 2 3 5 6 7 9 10 11 13 14 15 ALT GPIO SPIB_PO CI OUTPUTXB AR8 EQEP1_I NDEX FSIRXA_ D1 MCANA_TX EPWM1_B GPIO I2CA_SD A EQEP1_IND EX SPIB_CL K EPWM8_B LINA_TX FSIRXA_ D0 MCANB_TX PMBUSA_S DA ADCSOCBO GPIO
33 I2CA_SCL SPIB_PT
E OUTPUTXB AR4 LINA_RX FSIRXA_ CLK MCANB_RX EQEP2_B ADCSOCAO SCIC_RX GPIO OUTPUTX BAR1 PMBUSA_ SDA I2CB_SDA GPIO
35 SCIA_RX SPIA_POCI I2CA_SD
A MCANB_RX PMBUSA_ SCL LINA_RX EQEP1_A PMBUSA_C TL EPWM5_B TDI GPIO OUTPUTX BAR2 SPIA_PTE I2CA_SC L SCIA_TX MCANB_T X LINA_TX EQEP1_B PMBUSA_A LERT EPWM5_A TDO GPIO SPIB_PIC O EPWM2_B PMBUSA_ SDA FSIRXA_D0 SCIB_TX EQEP1_A LINA_TX CLB_OUTP UTXBAR4 EQEP3_STR OBE GPIO EPWM7_ A EPWM2_A PMBUSA_ SCL FSIRXA_D1 SCIB_RX EQEP1_B LINA_RX EPWM12_B SPIB_POCI USB0 DP GPIO
42 LINA_RX OUTPUT
PMBUSA_C TL I2CA_SD A SCIC_RX EQEP1_STR OBE CLB_OUTP UTXBAR3 GPIO OUTPUT XBAR6 PMBUSA_A LERT I2CA_SCL SCIC_TX PMBUSA_ ALERT EQEP1_IND EX CLB_OUTP UTXBAR4 GPIO OUTPUT XBAR7 EQEP1_A PMBUSA_ SDA FSITXA_CL K PMBUSA_ CTL CLB_OUTP UTXBAR3 FSIRXA_D0 LINA_TX GPIO OUTPUT XBAR8 FSITXA_D0 PMBUSA_ ALERT CLB_OUTP UTXBAR4 GPIO
46 LINA_TX MCANA_TX FSITXA_D1 PMBUSA_
47 LINA_RX MCANA_RX CLB_OUTP
PMBUSA_ SCL GPIO OUTPUTX BAR3 MCANA_TX SCIA_TX PMBUSA_ SDA GPIO OUTPUTX BAR4 MCANA_RX SCIA_RX LINA_RX FSITXA_D0 GPIO
50 EQEP1_A MCANA_TX SPIB_PIC
O I2CB_SD A FSITXA_D1 GPIO
51 EQEP1_B MCANA_RX SPIB_PO
CI I2CB_SCL FSITXA_CL K GPIO EQEP1_S TROBE CLB_OUTP UTXBAR5 SPIB_CLK SYNCOU T FSIRXA_D0 GPIO EQEP1_I NDEX CLB_OUTP UTXBAR6 SPIB_PTE ADCSOC AO MCANB_RX FSIRXA_D1 GPIO SPIA_PIC O EQEP2_A OUTPUTX BAR2 ADCSOC BO LINA_TX FSIRXA_CL K GPIO SPIA_PO CI EQEP2_B OUTPUTX BAR3 ERRORS TS LINA_RX GPIO
56 SPIA_CLK CLB_OUTP
MCANA_ TX EQEP2_STR OBE SCIB_TX SPIB_PIC O I2CA_SDA EQEP1_A FSIRXA_D1 GPIO
57 SPIA_PTE CLB_OUTP
MCANA_ RX EQEP2_IND EX SCIB_RX SPIB_PO CI I2CA_SCL EQEP1_B FSIRXA_CL K GPIO OUTPUTXB AR1 SPIB_CLK LINA_TX MCANB_TX EQEP1_STR OBE FSIRXA_D0 GPIO OUTPUTXB AR2 SPIB_PTE LINA_RX MCANB_RX EQEP1_IND EX GPIO EPWM12_ B MCANA_ TX OUTPUTXB AR3 SPIB_PIC O GPIO MCANA_ RX OUTPUTXB AR4 SPIB_PO CI MCANB_RX GPIO EPWM10_ A OUTPUTXB AR3 MCANA_TX SCIA_TX PMBUSA_ SDA GPIO EPWM10_ B OUTPUTXB AR4 MCANA_RX SCIA_RX LINA_RX GPIO
64 SCIA_RX EPWM11_A EPWM7_
A OUTPUTXB AR5 EQEP1_A EQEP2_S TROBE LINA_TX SPIB_CLK ERRORSTS I2CB_SDA GPIO
65 EQEP1_A EPWM11_B SPIB_PIC
O MCANA_T X I2CA_SCL GPIO
66 EQEP1_B EPWM12_A SPIB_PO
MCANA_ RX I2CA_SDA www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 53 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 5-6. GPIO Muxed Pins (continued) 0, 4, 8, 12 1 2 3 5 6 7 9 10 11 13 14 15 ALT GPIO EPWM7_ B EPWM12_B MCANA_ TX EQEP1_IND EX SCIB_RX PMBUSA_A LERT FSIRXA_ CLK LINA_RX SPIA_POCI SCIC_RX GPIO EPWM7_ A EPWM3_A MCANA_ RX EQEP1_STR OBE SCIB_TX PMBUSA_C TL FSIRXA_ D0 LINA_TX SPIA_CLK SCIC_TX GPIO EPWM6_ B EPWM3_B OUTPUT XBAR7 EQEP1_B SCIB_RX SPIA_PTE FSIRXA_ D1 LINA_RX EQEP2_A SPIA_PICO EQEP3_IND EX GPIO
70 I2CA_SCL SPIB_PT
E OUTPUTXB AR4 LINA_RX FSIRXA_ CLK MCANA_RX EQEP2_B ADCSOCAO EQEP3_A GPIO SPIA_PIC O EPWM4_B OUTPUT XBAR7 EPWM9_A SCIA_TX EQEP1_S TROBE PMBUSA_S CL XCLKOUT EQEP2_IND EX SPIB_POCI EQEP3_STR OBE GPIO SPIA_PO CI EPWM5_A OUTPUT XBAR8 EPWM9_B SCIA_RX EQEP1_I NDEX PMBUSA_S DA MCANA_TX EPWM6_A EQEP3_B GPIO OUTPUTX BAR1 EPWM5_B SPIA_PT E EPWM8_A SPIB_PIC O LINA_TX PMBUSA_S CL SCIA_TX ERRORSTS EPWM9_A GPIO EPWM2_ B ADCSOC AO MCANA_TX SPIA_PO CI EQEP1_B GPIO EPWM1_ B LINA_RX EPWM6_A SPIA_CLK EQEP1_STR OBE SCIC_RX GPIO EPWM4_ A OUTPUTXB AR2 SPIA_PTE MCANA_RX EQEP1_IND EX GPIO EPWM1_ A OUTPUTXB AR3 SPIA_PIC O MCANA_TX EQEP1_A SCIC_TX GPIO
78 EPWM8_A EPWM3_
A OUTPUTXB AR1 EPWM2_ B FSITXA_C LK GPIO
79 EPWM8_B EPWM3_
B MCANA_RX EPWM2_ A I2CA_SDA PMBUSA_ SCL GPIO EPWM1_ A OUTPUT XBAR7 SCIA_RX I2CB_SD A SPIA_PTE FSITXA_D
0 MCANA_RX CLB_OUTP
EQEP1_IND EX EPWM3_A GPIO EPWM1_ B OUTPUTXB AR6 SCIC_RX SPIB_CLK I2CB_SCL FSITXA_D
1 MCANA_TX EQEP3_IND
EPWM10_ A EQEP3_A GPIO 212 EPWM10_ B EQEP3_B GPIO 213 EPWM11_ A EQEP3_STR OBE GPIO 214 EPWM11_ B EQEP3_IND EX GPIO 215 EPWM7_ B EQEP2_A GPIO 224 EPWM11_ B OUTPUTXB AR3 SPIA_PIC O EPWM1_ A MCANA_TX EQEP1_A ADCE_EXT MUXSEL3 SCIC_TX GPIO 226 EPWM10_ B LINA_RX EPWM6_A SPIA_CLK EPWM1_ B EQEP1_STR OBE ADCE_EXT MUXSEL1 SCIC_RX GPIO
227 I2CB_SCL EPWM3_
A OUTPUTXB AR1 EPWM2_ B GPIO 228 EPWM10_ A ADCSOC AO MCANA_TX SPIA_PO CI EPWM2_ B EQEP1_B ADCE_EXT MUXSEL0 GPIO 230 I2CB_SD A EPWM3_ B MCANA_RX EPWM2_ A I2CA_SDA PMBUSA_ SCL GPIO 236 EPWM7_ A EQEP1_IND EX EPWM12_ A GPIO 242 EPWM11_ A OUTPUTXB AR2 SPIA_PTE EPWM4_ A MCANA_RX EQEP1_IND EX ADCE_EXT MUXSEL2 GPIO 247 EPWM12_ B GPIO 253 EPWM12_ A AIO20 AIO20 AIO21 AIO22 TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
54 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 5-6. GPIO Muxed Pins (continued) 0, 4, 8, 12 1 2 3 5 6 7 9 10 11 13 14 15 ALT AIO22 AIO23 AIO23 AIO23 AIO23 AIO23 AIO23 AIO23 AIO23 AIO24 AIO24 AIO24 AIO24 AIO24 AIO24 AIO25 AIO25
5.4.2 Digital Inputs on ADC Pins (AIOs)
Some GPIOs are multiplexed with analog pins and only have digital input functionality. These are also referred to as AIOs. Pins with only an AIO option on this port can only function in input mode. See the device data sheet for list of AIO signals. By default, these pins function as analog pins and the GPIOs are in a high-impedance state. The GPyAMSEL register is used to configure these pins for digital or analog operation. Note If digital signals with sharp edges (high dv/dt) are connected to the AIOs, cross-talk can occur with adjacent analog signals. Therefore, limit the edge rate of signals connected to AIOs if adjacent channels are being used for analog functions. www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 55 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
5.4.3 Digital Inputs and Outputs on ADC Pins (AGPIOs)
Some GPIOs are multiplexed with analog pins and have digital input and output functionality. These are also referred to as AGPIOs. Unlike AIOs, AGPIOs have full input and output capability. By default, the AGPIOs are not connected and must be configured. Table 5-7 shows how to configure the AGPIOs. To enable the analog functionality, set the register AGPIOCTRLx from analog subsystem. To enable the digital functionality, set the register GPxAMSEL from the General-Purpose Input/Output (GPIO) chapter. Table 5-7. AGPIO Configuration AGPIOCTRLx.GPIOy (Default = 0) GPxAMSEL.GPIOy (Default = 1) Pin Connected To: ADC GPIOy 0 0 - Yes 0 1 - (1) (1) 1 0 - Yes 1 1 Yes - (1) By default there are no signals connected to AGPIO pins. One of the other rows in the table must be chosen for pin functionality. Note If digital signals with sharp edges (high dv/dt) are connected to the AGPIOs, cross-talk can occur with adjacent analog signals. The user must therefore limit the edge rate of signals connected to AGPIOs, if adjacent channels are being used for analog functions. TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
56 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
5.4.4 GPIO Input X-BAR
The Input X-BAR is used to route signals from a GPIO to many different IP blocks such as the ADCs, eCAPs, ePWMs, and external interrupts (see the Input X-BAR figure). The Input X-BAR Destinations table lists the input X-BAR destinations. For details on configuring the Input X-BAR, see the Crossbar (X-BAR) chapter of the TMS320F28P55x Real-Time Microcontrollers Technical Reference Manual. EXT Y N1S NCI EXT Y N2S NCI CPU PIE CLA XINT1 XINT4 XINT5 XINT3 XINT2 ePWM and eCAP Sync Scheme ADCEXTSOC ADC Output X-BAR INPUT4INPUT13INPUT14 INPUT6INPUT5INPUT3INPUT2INPUT1 GPIO0 GPIOx Asynchronous Synchronous Sync. + Qual. Other SourcesOther Sources eCAP1 eCAP2 Input X-BAR INPUT10INPUT9INPUT8INPUT7INPUT12INPUT11INPUT15INPUT16 INPUT[16:1] Other Sources 15:0 127:16 ERADINPUT[1-16] DCCx Clock Source-1 DCCx Clock Source-0 CLB X-BARINPUT[1-14] EPG1IN1 EPG EPG1IN2 EPG1IN3 EPG1IN4 CMPSS1/3 FILINIT High CMPSS CMPSS1/3 FILINIT Low CMPSS2/4 FILINIT High CMPSS2/4 FILINIT Low ePWM X-BARINPUT[1-14] TZ1,TRIP1 ePWM Modules TZ2,TRIP2 TZ3,TRIP3 TRIP6 Figure 5-6. Input X-BAR Table 5-8. Input X-BAR Destinations Input ECAP EPWM XBAR CLB XBAR OUTPU T XBAR EPWM TRIP ERAD CPU XINT ADC SOC EPWM / ECAP SYNC CMPSS DCCx EPG INPUTXBAR1 Yes Yes Yes Yes TZ1, TRIP1 Yes INPUTXBAR2 Yes Yes Yes Yes TZ2, TRIP2 Yes INPUTXBAR3 Yes Yes Yes Yes TZ3, TRIP3 Yes INPUTXBAR4 Yes Yes Yes Yes Yes XINT1 INPUTXBAR5 Yes Yes Yes Yes Yes XINT2 ADCE XTSO C EXTSY NCIN1 INPUTXBAR6 Yes Yes Yes Yes TRIP6 Yes XINT3 EXTSY NCIN2 www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 57 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 5-8. Input X-BAR Destinations (continued) Input ECAP EPWM XBAR CLB XBAR OUTPU T XBAR EPWM TRIP ERAD CPU XINT ADC SOC EPWM / ECAP SYNC CMPSS DCCx EPG INPUTXBAR7 Yes Yes Yes Yes CMPSS1/3 EXT_FILTI N_H INPUTXBAR8 Yes Yes Yes Yes CMPSS1/3 EXT_FILTI N_L INPUTXBAR9 Yes Yes Yes Yes CMPSS2/4 EXT_FILTI N_H INPUTXBAR10 Yes Yes Yes Yes CMPSS2/4 EXT_FILTI N_L INPUTXBAR11 Yes Yes Yes Yes CLK1 INPUTXBAR12 Yes Yes Yes Yes CLK1 INPUTXBAR13 Yes Yes Yes Yes XINT4 EPGAI INPUTXBAR14 Yes Yes Yes Yes XINT5 EPGAI INPUTXBAR15 Yes Yes CLK1 EPGAI INPUTXBAR16 Yes Yes CLK0 EPGAI TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
58 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
5.4.5 GPIO Output X-BAR, CLB X-BAR, CLB Output X-BAR, and ePWM X-BAR
The Output X-BAR has eight outputs that can be selected on the GPIO mux as OUTPUTXBARx. The CLB X-BAR has eight outputs that are connected to the CLB global mux as AUXSIGx. The CLB Output X-BAR has eight outputs that can be selected on the GPIO mux as CLB_OUTPUTXBARx. The ePWM X-BAR has eight outputs that are connected to the TRIPx inputs of the ePWM. The sources for the Output X-BAR, CLB X-BAR, CLB Output X-BAR, and ePWM X-BAR are shown in Figure 5-7. For details on the Output X-BAR, CLB X-BAR, CLB Output X-BAR, and ePWM X-BAR, see the Crossbar (X-BAR) chapter of the TMS320F28P55x Real-Time Microcontrollers Technical Reference Manual. www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 59 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
CLB_OUTPUTXBAR1 CLB_OUTPUTXBAR2 CLB_OUTPUTXBAR3 CLB_OUTPUTXBAR4 CLB_OUTPUTXBAR5 CLB_OUTPUTXBAR6 CLB_OUTPUTXBAR7 CLB_OUTPUTXBAR8 eQEPx TRIP1 TRIP2 TRIP3 TRIP4 TRIP5 TRIP6 TRIP7 TRIP8 TRIP9 TRIP10 TRIP11 TRIP12 TRIP14 TRIP15 X-BAR Flags (shared) CTRIPOUTH CTRIPOUTL CTRIPH CTRIPL EXTSYNCOUT ADCSOCA0 ADCSOCB0 ECAPxOUT EVT1 EVT2 EVT3 EVT4 GPIO Mux All ePWM Modules CLB X-BAR AUXSIG1 AUXSIG2 AUXSIG3 AUXSIG4 AUXSIG5 AUXSIG6 AUXSIG7 AUXSIG8 CLB Global Mux CLB Output X-BAR CLB TILExCLB Input X-BAR CLAHALT CLAHALT CLB FSI EPG EPG1.EPGOUT RXTRIG[1-3] CLBx_OUT[0-7] Input X-BAR INPUT1-14 ERAD EVT[8-11] MCANx FEVT[0-2] Figure 5-7. Output X-BAR, CLB X-BAR, CLB Output X-BAR, and ePWM X-BAR Sources TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
60 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
5.5 Pins With Internal Pullup and Pulldown
Some pins on the device have internal pullups or pulldowns. Table 5-9 lists the pull direction and when it is active. The pullups on GPIO pins are disabled by default and can be enabled through software. To avoid any floating unbonded inputs, the Boot ROM will enable internal pullups on GPIO pins that are not bonded out in a particular package. Other pins noted in Table 5-9 with pullups and pulldowns are always on and cannot be disabled. Table 5-9. Pins With Internal Pullup and Pulldown PIN RESET (XRSn = 0) DEVICE BOOT APPLICATION GPIOx Pullup disabled Pullup disabled(1) Application defined GPIO35/TDI Pullup disabled Application defined GPIO37/TDO Pullup disabled Application defined TCK Pullup active TMS Pullup active XRSn Pullup active Other pins (including AIOs) No pullup or pulldown present (1) Pins not bonded out in a given package will have the internal pullups enabled by the Boot ROM. www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 61 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
5.6 Connections for Unused Pins
For applications that do not need to use all functions of the device, Table 5-10 lists acceptable conditioning for any unused pins. When multiple options are listed in Table 5-10, any option is acceptable. Pins not listed in Table 5-10 must be connected according to Section 5. Table 5-10. Connections for Unused Pins SIGNAL NAME ACCEPTABLE PRACTICE ANALOG VREFHI Tie to VDDA (applies only if ADC is not used in the application) VREFLO Tie to VSSA Analog input pins with DACx_OUT
- No Connect
- Tie to VSSA through 4.7-kΩ or larger resistor Analog input pins (except DACx_OUT)
- No Connect
- Tie to VSSA
- Tie to VSSA through resistor Analog input pins (shared with GPIOs)(1)
- No connection (digital input mode with internal pullup enabled)
- No connection (digital output mode with internal pullup disabled)
- Pullup or pulldown resistor (any value resistor, digital input mode, and with internal pullup disabled) DIGITAL GPIOx
- No connection (input mode with internal pullup enabled)
- No connection (output mode with internal pullup disabled)
- Pullup or pulldown resistor (any value resistor, input mode, and with internal pullup disabled) GPIO35/TDI When TDI mux option is selected (default), the GPIO is in Input mode.
- Internal pullup enabled
- External pullup resistor GPIO37/TDO When TDO mux option is selected (default), the GPIO is in Output mode only during JTAG activity; otherwise, it is in a tri-state condition. The pin must be biased to avoid extra current on the input buffer.
- Internal pullup enabled
- External pullup resistor TCK
- No Connect
- Pullup resistor TMS Pullup resistor GPIO19/X1 Turn XTAL off and:
- Input mode with internal pullup enabled
- Input mode with external pullup or pulldown resistor
- Output mode with internal pullup disabled GPIO18/X2 Turn XTAL off and:
- Input mode with internal pullup enabled
- Input mode with external pullup or pulldown resistor
- Output mode with internal pullup disabled TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
62 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 5-10. Connections for Unused Pins (continued) SIGNAL NAME ACCEPTABLE PRACTICE POWER AND GROUND VDD All VDD pins must be connected per Section 5.3. Pins should not be used to bias any external circuits. VDDA If a dedicated analog supply is not used, tie to VDDIO. VDDIO All VDDIO pins must be connected per Section 5.3. VSS All VSS pins must be connected to board ground. VSSA If an analog ground is not used, tie to VSS. (1) AGPIO pins share analog and digital functionality. The actions here only apply if these pins are also not being used for analog functions. www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 63 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6 Specifications
6.1 Absolute Maximum Ratings
over recommended operating conditions (unless otherwise noted)(1) (2) MIN MAX UNIT Supply voltage VDD with respect to VSS –0.3 1.5 VVDDIO with respect to VSS –0.3 4.6 VDDA with respect to VSSA –0.3 4.6 Input voltage(7) VIN (3.3 V) –0.3 4.6 V Output voltage VO –0.3 4.6 V Input clamp current - per pin(4) (6) IIK - VIN < VSS/VSSA - VIN > VDDIO/VDDA –20 20 mA Input clamp current - per pin: GPIO2/3/9/32 IIK - VIN < VSS –20 mA Input clamp current - total for all inputs(4) (6) IIKTOTAL - VIN < VSS/VSSA - VIN > VDDIO/VDDA –20 20 mA Output current Digital output (per pin), IOUT –20 20 mA Operating junction temperature TJ –40 155 °C Storage temperature(3) Tstg –65 150 °C (1) Operation outside the Absolute Maximum Ratings may cause permanent device damage. Absolute Maximum Ratings do not imply functional operation of the device at these or any other conditions beyond those listed under Recommended Operating Conditions. If used outside the Recommended Operating Conditions but within the Absolute Maximum Ratings, the device may not be fully functional, and this may affect device reliability, functionality, performance, and shorten the device lifetime. (2) All voltage values are with respect to VSS, unless otherwise noted. (3) Long-term high-temperature storage or extended use at maximum temperature conditions may result in a reduction of overall device life. For additional information, see the Semiconductor and IC Package Thermal Metrics Application Report. (4) Continuous clamp current per pin is ±2mA (5) GPIO2, GPIO3, GPIO9, GPIO32 Only (6) Applying a VIN greater than VDDIO/VDDA or less than VSS/VSSA will turn on the ESD current clamping diode causing additional current flow to the respective supply rail. If this occurs, the current must be kept within the MIN/MAX listed to prevent permanent damage to the device. (7) Input clamp current must also be observed. TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
64 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.2 ESD Ratings – Commercial
All F28P550Sxx devices in 128-pin PDT package V(ESD) Electrostatic discharge Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001(1) ±2000 VCharged-device model (CDM), per ANSI/ESDA/JEDEC JS-002(2) All pins ±500 Corner pins on 128-pin PDT: 1, 32, 33, 64, 65, 96, 97, 128 ±750 All F28P550Sxx devices in 100-pin PZ package V(ESD) Electrostatic discharge Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001(1) ±2000 VCharged-device model (CDM), per ANSI/ESDA/JEDEC JS-002(2) All pins ±500 Corner pins on 100-pin PZ: 1, 25, 26, 50, 51, 75, 76, 100 ±750 All F28P550Sxx devices in 80-pin PNA package V(ESD) Electrostatic discharge Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001(1) ±2000 VCharged-device model (CDM), per ANSI/ESDA/JEDEC JS-002(2) All pins ±500 Corner pins on 80-pin PNA: 1, 20, 21, 40, 41, 60, 61, 80 ±750 All F28P550Sxx devices in 64-pin PM package V(ESD) Electrostatic discharge Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001(1) ±2000 VCharged-device model (CDM), per ANSI/ESDA/JEDEC JS-002(2) All pins ±500 Corner pins on 64-pin PM: 1, 16, 17, 32, 33, 48, 49, 64 ±750 All F28P550Sxx devices in 56-pin RSH package V(ESD) Electrostatic discharge Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001(1) ±2000 VCharged-device model (CDM), per ANSI/ESDA/JEDEC JS-002(2) All pins ±500 Corner pins on 56-pin RSH: 1, 14, 15, 28, 29, 42, 43, 56 ±750 (1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. (2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process. www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 65 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.3 ESD Ratings – Automotive
All F28P559Sxx-Q1 devices in 128-pin PDT package V(ESD) Electrostatic discharge Human body model (HBM), per AEC Q100-002(1) All pins ±2000 VCharged device model (CDM), per AEC Q100-011 All pins ±500 Corner pins on 128-pin PDT: 1, 32, 33, 64, 65, 96, 97, 128 ±750 All F28P559Sxx-Q1 devices in 100-pin PZ package V(ESD) Electrostatic discharge Human body model (HBM), per AEC Q100-002(1) All pins ±2000 VCharged device model (CDM), per AEC Q100-011 All pins ±500 Corner pins on 100-pin PZ: 1, 25, 26, 50, 51, 75, 76, 100 ±750 All F28P559Sxx-Q1 devices in 80-pin PNA package V(ESD) Electrostatic discharge Human body model (HBM), per AEC Q100-002(1) All pins ±2000 VCharged device model (CDM), per AEC Q100-011 All pins ±500 Corner pins on 80-pin PNA: 1, 20, 21, 40, 41, 60, 61, 80 ±750 All F28P559Sxx-Q1 devices in 64-pin PM package V(ESD) Electrostatic discharge Human body model (HBM), per AEC Q100-002(1) All pins ±2000 VCharged device model (CDM), per AEC Q100-011 All pins ±500 Corner pins on 64-pin PM: 1, 16, 17, 32, 33, 48, 49, 64 ±750 (1) AEC Q100-002 indicates HBM stressing is done in accordance with the ANSI/ESDA/JEDEC JS-001 specification.
6.4 Recommended Operating Conditions
Device supply voltage, VDDIO and VDDA Internal BOR enabled(3) VBOR-VDDIO(MAX) + VBOR-GB (2) 3.3 3.63 V Internal BOR disabled 2.8 3.3 3.63 Device supply voltage, VDD 1.14 1.2 1.32 V Device ground, VSS 0 V Analog ground, VSSA 0 V SRSUPPLY Supply ramp rate of VDDIO, VDD, VDDA with respect to VSS.(4) VIN Digital input voltage(6) VSS – 0.3 VDDIO + 0.3 V Digital input voltage(GPIO2, 3, 9, and Analog input voltage(6) VSSA – 0.3 VDDA + 0.3 V Junction temperature, TJ (1) –40 150 °C Free-Air temperature, TA –40 125 °C (1) Operation above TJ = 105°C for extended duration will reduce the lifetime of the device. See Calculating Useful Lifetimes of Embedded Processors for more information. (2) See the Power Management Module (PMM) section. (3) Internal BOR is enabled by default. (4) See the Power Management Module Operating Conditions table. (5) These pins support applied voltage prior to the device being powered (6) Applying a VIN greater than VDDIO/VDDA or less than VSS/VSSA will turn on the ESD current clamping diode causing additional current flow to the respective supply rail. VDDIO/VDDA voltage will internally rise and could impact other electrical characteristics. TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
66 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.5 Power Consumption Summary
Current values listed in this section are representative for the test conditions given and not the absolute maximum possible. The actual device currents in an application will vary with application code and pin configurations.
6.5.1 System Current Consumption - VREG Enable - Internal Supply
Over recommended operating conditions (unless otherwise noted) TYP : Vnom, Temperatures shown are TJ PARAMETER TEST CONDITIONS MIN TYP MAX UNIT OPERATING MODE IDDIO VDDIO current consumption during operational usage This is an estimation of current for a typical heavily loaded application. Actual currents will vary depending on system activity, I/O electrical loading and switching frequency. This includes Core supply current with Internal Vreg Enabled. - CPU is running from RAM - Flash is powered up - X1/X2 crystal is powered up - PLL is enabled, SYSCLK=Max Device frequency - Analog modules are powered up - Outputs are static without DC Load - Inputs are static high or low 30 ℃ 92 mA 85 ℃ 105 mA 125 ℃ 115 mA IDDA VDDA current consumption during operational usage 30 ℃ 1 mA 85 ℃ 3 mA 125 ℃ 8 mA IDLE MODE IDDIO VDDIO current consumption while device is in Idle mode - CPU is in IDLE mode - Flash is powered down - PLL is Enabled, SYSCLK=Max Device Frequency, CPUCLK is gated - X1/X2 crystal is powered up - Analog Modules are powered down - Outputs are static without DC Load - Inputs are static high or low 30 ℃ 30 mA 85 ℃ 36 mA 125 ℃ 48 mA IDDA VDDA current consumption while device is in Idle mode 30 ℃ 1 mA 85 ℃ 3 mA 125 ℃ 8 mA STANDBY MODE (PLL Enabled) IDDIO VDDIO current consumption while device is in Standby mode - CPU is in STANDBY mode - Flash is powered down - PLL is Enabled, SYSCLK & CPUCLK are gated - X1/X2 crystal is powered down - Analog Modules are powered down - Outputs are static without DC Load - Inputs are static high or low 30 ℃ 8 mA 85 ℃ 14 mA 125 ℃ 25 mA IDDA VDDA current consumption while device is in Standby mode 30 ℃ 1 mA 85 ℃ 3 mA 125 ℃ 8 mA www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 67 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.5.1 System Current Consumption - VREG Enable - Internal Supply (continued)
Over recommended operating conditions (unless otherwise noted) TYP : Vnom, Temperatures shown are TJ PARAMETER TEST CONDITIONS MIN TYP MAX UNIT STANDBY MODE (PLL Disabled) IDDIO VDDIO current consumption while device is in Standby mode - CPU is in STANDBY mode - Flash is powered down - PLL is Disabled, SYSCLK & CPUCLK are gated - X1/X2 crystal is powered down - Analog Modules are powered down - Outputs are static without DC Load - Inputs are static high or low 30 ℃ 4 mA 85 ℃ 10 mA 125 ℃ 21 mA IDDA VDDA current consumption while device is in Standby mode 30 ℃ 1 mA 85 ℃ 3 mA 125 ℃ 8 mA HALT MODE IDDIO VDDIO current consumption while device is in Halt mode - CPU is in HALT mode - Flash is powered down - PLL is Disabled, SYSCLK and CPUCLK are gated - X1/X2 crystal is powered down - Analog Modules are powered down - Outputs are static without DC Load - Inputs are static high or low 30 ℃ 4 mA 85 ℃ 10 mA 125 ℃ 20 mA IDDA VDDA current consumption while device is in Halt mode 30 ℃ 1 mA 85 ℃ 3 mA 125 ℃ 8 mA FLASH ERASE/PROGRAM IDDIO VDDIO current consumption during Erase/Program cycle(1) - CPU is running from RAM - Flash going through continuous Program/Erase operation - PLL is enabled, SYSCLK at 120 MHz. - Peripheral clocks are turned OFF. - X1/X2 crystal is powered up - Analog is powered down - Outputs are static without DC Load - Inputs are static high or low 91 128 mA IDDA VDDA current consumption during Erase/Program cycle 0.1 8 mA RESET MODE IDDIO VDDIO current consumption while reset is active(2) Device is under Reset 30 ℃ 10 mA 85 ℃ 13 mA 125 ℃ 20 mA IDDA VDDA current consumption while reset is active(2) 30 ℃ 0.01 mA 85 ℃ 0.01 mA 125 ℃ 0.01 mA (1) Brownout events during flash programming can corrupt flash data and permanently lock the device. Programming environments using alternate power sources (such as a USB programmer) must be capable of supplying the rated current for the device and other system components with sufficient margin to avoid supply brownout conditions. (2) This is the current consumption while reset is active, that is, XRSn is low. TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
68 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.5.2 System Current Consumption - VREG Disable - External Supply
Over recommended operating conditions (unless otherwise noted) TYP : Vnom, Temperatures shown are TJ PARAMETER TEST CONDITIONS MIN TYP MAX UNIT OPERATING MODE IDD VDD current consumption during operational usage This is an estimation of current for a typical heavily loaded application. Actual currents will vary depending on system activity, I/O electrical loading and switching frequency. This includes Core supply current with Internal Vreg Enabled. - CPU is running from RAM - Flash is powered up - X1/X2 crystal is powered up - PLL is enabled, SYSCLK=Max Device frequency - Analog modules are powered up - Outputs are static without DC Load - Inputs are static high or low 30 ℃ 85 mA 85 ℃ 96 mA 125 ℃ 108 mA IDDIO VDDIO current consumption during operational usage 30 ℃ 13 mA 85 ℃ 17 mA 125 ℃ 18 mA IDDA VDDA current consumption during operational usage 30 ℃ 1 mA 85 ℃ 3 mA 125 ℃ 8 mA IDLE MODE IDD VDD current consumption while device is in Idle mode - CPU is in IDLE mode - Flash is powered down - PLL is Enabled, SYSCLK=Max Device Frequency, CPUCLK is gated - X1/X2 crystal is powered up - Analog Modules are powered down - Outputs are static without DC Load - Inputs are static high or low 30 ℃ 28 mA 85 ℃ 35 mA 125 ℃ 47 mA IDDIO VDDIO current consumption while device is in Idle mode 30 ℃ 3 mA 85 ℃ 6 mA 125 ℃ 7 mA IDDA VDDA current consumption while device is in Idle mode 30 ℃ 1 mA 85 ℃ 3 mA 125 ℃ 8 mA STANDBY MODE (PLL Enabled) IDD VDD current consumption while device is in Standby mode - CPU is in STANDBY mode - Flash is powered down - PLL is Enabled, SYSCLK & CPUCLK are gated - X1/X2 crystal is powered down - Analog Modules are powered down - Outputs are static without DC Load - Inputs are static high or low 30 ℃ 6 mA 85 ℃ 12 mA 125 ℃ 24 mA IDDIO VDDIO current consumption while device is in Standby mode 30 ℃ 3 mA 85 ℃ 6 mA 125 ℃ 7 mA IDDA VDDA current consumption while device is in Standby mode 30 ℃ 1 mA 85 ℃ 3 mA 125 ℃ 8 mA www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 69 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.5.2 System Current Consumption - VREG Disable - External Supply (continued)
Over recommended operating conditions (unless otherwise noted) TYP : Vnom, Temperatures shown are TJ PARAMETER TEST CONDITIONS MIN TYP MAX UNIT STANDBY MODE (PLL Disabled) IDD VDD current consumption while device is in Standby mode - CPU is in STANDBY mode - Flash is powered down - PLL is Disabled, SYSCLK & CPUCLK are gated - X1/X2 crystal is powered down - Analog Modules are powered down - Outputs are static without DC Load - Inputs are static high or low 30 ℃ 3 mA 85 ℃ 8 mA 125 ℃ 20 mA IDDIO VDDIO current consumption while device is in Standby mode 30 ℃ 2 mA 85 ℃ 5 mA 125 ℃ 6 mA IDDA VDDA current consumption while device is in Standby mode 30 ℃ 1 mA 85 ℃ 3 mA 125 ℃ 8 mA HALT MODE IDD VDD current consumption while device is in Halt mode - CPU is in HALT mode - Flash is powered down - PLL is Disabled, SYSCLK and CPUCLK are gated - X1/X2 crystal is powered down - Analog Modules are powered down - Outputs are static without DC Load - Inputs are static high or low 30 ℃ 2 mA 85 ℃ 8 mA 125 ℃ 20 mA IDDIO VDDIO current consumption while device is in Halt mode 30 ℃ 2 mA 85 ℃ 5 mA 125 ℃ 6 mA IDDA VDDA current consumption while device is in Halt mode 30 ℃ 1 mA 85 ℃ 3 mA 125 ℃ 8 mA FLASH ERASE/PROGRAM IDD VDD current consumption during Erase/Program cycle(1) - CPU is running from RAM - Flash going through continuous Program/Erase operation - PLL is enabled, SYSCLK at 100 MHz. - Peripheral clocks are turned OFF. - X1/X2 crystal is powered up - Analog is powered down - Outputs are static without DC Load - Inputs are static high or low 80 108 mA IDDIO VDDIO current consumption during Erase/Program cycle(1) 11 20 mA IDDA VDDA current consumption during Erase/Program cycle 0.1 8 mA TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
70 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Over recommended operating conditions (unless otherwise noted) TYP : Vnom, Temperatures shown are TJ PARAMETER TEST CONDITIONS MIN TYP MAX UNIT RESET MODE IDD VDD current consumption while reset is active(2) Device is under Reset 30 ℃ 5 mA 85 ℃ 8 mA 125 ℃ 15 mA IDDIO VDDIO current consumption while reset is active(2) 30 ℃ 5 mA 85 ℃ 5 mA 125 ℃ 5 mA IDDA VDDA current consumption while reset is active(2) 30 ℃ 0.01 mA 85 ℃ 0.01 mA 125 ℃ 0.01 mA (1) Brownout events during flash programming can corrupt flash data and permanently lock the device. Programming environments using alternate power sources (such as a USB programmer) must be capable of supplying the rated current for the device and other system components with sufficient margin to avoid supply brownout conditions. (2) This is the current consumption while reset is active, that is XRSn is low. www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 71 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.5.3 Operating Mode Test Description
The System Current Consumption - VREG Enable - Internal Supply table, System Current Consumption - VREG Disable - External Supply table, and Section 6.5.4 list the current consumption values for the operational mode of the device. The operational mode provides an estimation of what an application might encounter. The test condition for these measurements has the following properties:
- Code is executing from RAM.
- FLASH is read and kept in active state.
- No external components are driven by I/O pins.
- All peripherals have clocks enabled.
- The CPU is actively executing code.
- All analog peripherals are powered up. ADCs and DACs are periodically converting.
6.5.4 Reducing Current Consumption
The F28P55x devices provide some methods to reduce the device current consumption:
- One of the two low-power modes—IDLE or STANDBY—could be entered during idle periods in the application.
- The flash module may be powered down if the code is run from RAM.
- Disable the pullups on pins that assume an output function.
- Each peripheral has an individual clock-enable bit (PCLKCRx). Reduced current consumption may be achieved by turning off the clock to any peripheral that is not used in a given application. The Typical Current Reduction per Disabled Peripheral table lists the typical current reduction that may be achieved by disabling the clocks using the PCLKCRx register.
- To realize the lowest VDDA current consumption in an LPM, see the Analog-to-Digital Converter (ADC) chapter of the TMS320F28P55x Real-Time Microcontrollers Technical Reference Manual to ensure each module is powered down as well.
6.5.4.1 Typical Current Reduction per Disabled Peripheral
For peripherals with multiple instances, the current quoted is for all modules combined. PERIPHERAL IDDIO CURRENT REDUCTION (mA) ADC(1) 1.0 CLA 0.56 CLB 1.41 CMPSS(1) 0.31 CPU TIMER 0.06 GPDAC 0.12 MCAN 1.01 DCC 0.08 eCAP 0.12 ERAD 1.56 EPG 0.32 ePWM(per) 0.95 eQEP 0.18 SCI 0.50 I2C 0.51 SPI 0.11 FSI RX 0.34 FSI TX 0.27 PMBUS 0.28 (1) This current represents the current drawn by the digital portion of the each module. TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
72 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.6 Electrical Characteristics
over recommended operating conditions (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT Digital and Analog IO VOH High-level output voltage IOH = IOH MIN VDDIO * 0.8 V IOH = –100 μA VDDIO – 0.2 VOL Low-level output voltage IOL = IOL MAX 0.4 V IOL = 100 µA 0.2 IOH High-level output source current for all output pins –4 mA IOL Low-level output sink current for all output pins 4 mA Low-level output sink current for all output pins - GPIO2/3/9/32 IO_DRVSEL:DRVSELG PIOx = 0 4 mA IO_DRVSEL:DRVSELG PIOx = 1 12 mA ROH High-level output impedance for all output pins VOH=VDDS-0.4V 50 66 96 Ω ROL Low-level output impedance for all output pins VOL=0.4V 48 60 84 Ω VIH High-level input voltage 2.0 V High-level input voltage - GPIO2/3/9/32 IO_MODSEL:MODSEL GPIOx = 0 0.7*VDDIO V IO_MODSEL:MODSEL GPIOx = 1 1.35 V VIL Low-level input voltage 0.8 V Low-level input voltage - GPIO2/3/9/32 IO_MODSEL:MODSEL GPIOx = 0 0.3*VDDIO V IO_MODSEL:MODSEL GPIOx = 1 0.8 V VHYSTERESIS Input hysteresis (AIO) 125 mV Input hysteresis (GPIO) 125 IPULLDOWN Input current Pins with pulldown VDDIO = 3.3 V VIN = VDDIO 120 µA IPULLUP Input current Digital inputs with pullup enabled(1) VDDIO = 3.3 V VIN = 0 V 160 µA RPULLDOWN Weak pulldown resistance 22 31 62 kΩ RPULLUP Weak pullup resistance 19 29 54 kΩ GPIO2/3/9/32 20 31 65 kΩ ILEAK Pin leakage Digital inputs Pullups and outputs disabled
0 V ≤ VIN ≤ VDDIO
0.1 µADigital inputs (GPIO2/3/9/32 only) 20 Analog pins Analog drivers disabled
0 V ≤ VIN ≤ VDDA
0.1 CI Input capacitance Digital inputs 2 pF Analog pins(2) www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 73 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.6 Electrical Characteristics (continued)
over recommended operating conditions (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT VREG and BOR VREG, POR, BOR(3) (1) See the Pins With Internal Pullup and Pulldown table for a list of pins with a pullup or pulldown. (2) The analog pins are specified separately; see the Per-Channel Parasitic Capacitance tables that are in the ADC Input Model section. (3) See the Power Management Module (PMM) section. TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
74 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.7 Thermal Resistance Characteristics for PDT Package
°C/W(1) RΘJC Junction-to-case thermal resistance 10.6 RΘJB Junction-to-board thermal resistance 24.9 RΘJA (High k PCB) Junction-to-free air thermal resistance 42.5 PsiJT Junction-to-package top 0.4 PsiJB Junction-to-board 24.4 (1) These values are based on a JEDEC-defined 2S2P system (with the exception of the Theta JC [RΘJC] value, which is based on a JEDEC-defined 1S0P system) and will change based on environment as well as application. For more information, see these EIA/JEDEC standards:
- JESD51-2, Integrated Circuits Thermal Test Method Environmental Conditions - Natural Convection (Still Air)
- JESD51-3, Low Effective Thermal Conductivity Test Board for Leaded Surface Mount Packages
- JESD51-7, High Effective Thermal Conductivity Test Board for Leaded Surface Mount Packages
- JESD51-9, Test Boards for Area Array Surface Mount Package Thermal Measurements
6.8 Thermal Resistance Characteristics for PZ Package
°C/W(1) RΘJC Junction-to-case thermal resistance 11 RΘJB Junction-to-board thermal resistance 28.8 RΘJA (High k PCB) Junction-to-free air thermal resistance 46.4 PsiJT Junction-to-package top 0.4 PsiJB Junction-to-board 28.2 (1) These values are based on a JEDEC-defined 2S2P system (with the exception of the Theta JC [RΘJC] value, which is based on a JEDEC-defined 1S0P system) and will change based on environment as well as application. For more information, see these EIA/JEDEC standards:
- JESD51-2, Integrated Circuits Thermal Test Method Environmental Conditions - Natural Convection (Still Air)
- JESD51-3, Low Effective Thermal Conductivity Test Board for Leaded Surface Mount Packages
- JESD51-7, High Effective Thermal Conductivity Test Board for Leaded Surface Mount Packages
- JESD51-9, Test Boards for Area Array Surface Mount Package Thermal Measurements
6.9 Thermal Resistance Characteristics for PNA Package
°C/W(1) RΘJC Junction-to-case thermal resistance 14.5 RΘJB Junction-to-board thermal resistance 29.5 RΘJA (High k PCB) Junction-to-free air thermal resistance 51.7 PsiJT Junction-to-package top 0.5 PsiJB Junction-to-board 29.4 (1) These values are based on a JEDEC-defined 2S2P system (with the exception of the Theta JC [RΘJC] value, which is based on a JEDEC-defined 1S0P system) and will change based on environment as well as application. For more information, see these EIA/JEDEC standards:
- JESD51-2, Integrated Circuits Thermal Test Method Environmental Conditions - Natural Convection (Still Air)
- JESD51-3, Low Effective Thermal Conductivity Test Board for Leaded Surface Mount Packages
- JESD51-7, High Effective Thermal Conductivity Test Board for Leaded Surface Mount Packages
- JESD51-9, Test Boards for Area Array Surface Mount Package Thermal Measurements www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 75 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.10 Thermal Resistance Characteristics for PM Package
°C/W(1) RΘJC Junction-to-case thermal resistance 11.6 RΘJB Junction-to-board thermal resistance 24.9 RΘJA (High k PCB) Junction-to-free air thermal resistance 45 PsiJT Junction-to-package top 0.4 PsiJB Junction-to-board 24.5 (1) These values are based on a JEDEC-defined 2S2P system (with the exception of the Theta JC [RΘJC] value, which is based on a JEDEC-defined 1S0P system) and will change based on environment as well as application. For more information, see these EIA/JEDEC standards:
- JESD51-2, Integrated Circuits Thermal Test Method Environmental Conditions - Natural Convection (Still Air)
- JESD51-3, Low Effective Thermal Conductivity Test Board for Leaded Surface Mount Packages
- JESD51-7, High Effective Thermal Conductivity Test Board for Leaded Surface Mount Packages
- JESD51-9, Test Boards for Area Array Surface Mount Package Thermal Measurements
6.11 Thermal Resistance Characteristics for RSH Package
°C/W(1) RΘJC Junction-to-case thermal resistance(top) 11.6 Junction-to-case thermal resistance(bottom) 1.2 RΘJB Junction-to-board thermal resistance 6.7 RΘJA (High k PCB) Junction-to-free air thermal resistance 23.7 PsiJT Junction-to-package top 0.1 PsiJB Junction-to-board 6.7
6.12 Thermal Design Considerations
Based on the end application design and operational profile, the I DD and I DDIO currents could vary. Systems that exceed the recommended maximum power dissipation in the end product may require additional thermal enhancements. Ambient temperature (T A) varies with the end application and product design. The critical factor that affects reliability and functionality is T J, the junction temperature, not the ambient temperature. Hence, care should be taken to keep T J within the specified limits. T case should be measured to estimate the operating junction temperature TJ. Tcase is normally measured at the center of the package top-side surface. The thermal application report Semiconductor and IC Package Thermal Metrics helps to understand the thermal metrics and definitions. TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
76 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.13 System
6.13.1 Power Management Module (PMM)
6.13.1.1 Introduction
The Power Management Module (PMM) handles all the power management functions required for device operation.
6.13.1.2 Overview
The block diagram of the PMM is shown in Figure 6-1 . As can be seen, the PMM comprises of various subcomponents, which are described in the subsequent sections. MCU I/O BOR VDDIO VDD VSS XRSn EN I/O POR VDD POR 1.2v LDO VREG EN RISE DELAY (80us) OUT IN RISE DELAY (Ext VREG = 320us) (Int VREG = 40us) Internal All Monitors Release Signal VSS CVDDIO CVDD PMM Internal External Internal External To Rest of Chip VMONCTL.bit.BORLVMONDIS CPU Reset Release VREGENZ Figure 6-1. PMM Block Diagram
6.13.1.2.1 Power Rail Monitors
The PMM has voltage monitors on the supply rails that release the XRSn signal high once the voltages cross the set threshold during power up. They also function to trip the XRSn signal low if any of the voltages drop below the programmed levels. The various voltage monitors are described in subsequent sections. Note Not all the voltage monitors are supported for device operation in an application after boot up. In the case where a voltage monitor is not supported, an external supervisor is recommended if the device needs supply voltage monitoring while the application is running. www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 77 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
The three voltage monitors (I/O POR, I/O BOR, VDD POR) all have to release their respective outputs before the device begins operation (that is, XRSn goes high). However, if any of the voltage monitors trips, XRSn is driven low. The I/Os are held in high impedance when any of the voltage monitors trip. The I/O POR monitor supervises the VDDIO rail. During power up, this is the first monitor to release (that is, first to untrip) on VDDIO. The I/O BOR monitor also supervises the VDDIO rail. During power up, this is the second monitor to release (that is, second to untrip) on VDDIO. This monitor has a tighter tolerance compared to the I/O POR. Any drop in voltage below the recommended operating voltages will trip the I/O BOR and reset the device but this can be disabled by setting VMONCTL.bit.BORLVMONDIS to 1. The I/O BOR can only be disabled after the device has fully booted up. If the I/O BOR is disabled, the I/O POR will reset the device for voltage drops. Note The level at which the I/O POR trips is well below the minimum recommended voltage for VDDIO, and therefore should not be used for device supervision. Figure 6-2 shows the operating region of the I/O BOR.
3.3 V 0%
3.0 V –9.1% +10%3.63 V Recommended System Voltage Regulator Range VDDIO Operating Range VBOR-VDDIO Internal BOR Threshold –15.1%2.80 V VBOR-GB BOR Guard Band –14.8%2.81 V 3.1 V –6.1% Figure 6-2. I/O BOR Operating Region The VDD POR monitor supervises the VDD rail. During power up, this monitor releases (that is, untrips) once the voltage crosses the programmed trip level on VDD. Note VDD POR is programmed at a level below the minimum recommended voltage for VDD, and therefore it should not be relied upon for VDD supervision if that is required in the application.
6.13.1.2.2 External Supervisor Usage
VDDIO Monitoring: The I/O BOR is supported for application use, so an external supervisor is not required to monitor the I/O rail. TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
78 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
VDD Monitoring:
- VDD supplied from the internal VREG: The VDD supply is derived from the VDDIO supply. The VREG is designed in such a way that a valid VDDIO supply(monitored by the IO BOR) implies a valid VDD supply.
- VDD supplied from an external supply: The VDD POR is not supported for application use. If VDD monitoring is required by the application, an external supervisor can be used to monitor the VDD rail. Note The use of an external supervisor with the internal VREG is not supported. If VDD monitoring is required by the application, a package with a VREGENZ pin must be used to power VDD externally.
6.13.1.2.3 Delay Blocks
The delay blocks in the path of the voltage monitors work together to delay the release time between the voltage monitors and XRSn. This is to ensure that the voltages are stable when XRSn releases. The delay blocks are only active during power up (that is, when VDDIO and VDD are ramping up). The delay blocks contribute to the minimum slew rates specified in Power Management Module Electrical Data and Timing for the power rails. Note The delay numbers specified in the block diagram are typical numbers. The internal VREG is supplied by the VDDIO rail and can generate the 1.2 V required to power the VDD pins. Although the internal VREG eliminates the need to use an external supply for VDD, decoupling capacitors are still required on the VDD pins for VREG stability and transients. See the VDD Decoupling section for details.
6.13.1.2.5 VREGENZ
The VREGENZ (VREG disable) pin controls the state of the internal VREG. To enable the internal VREG, connect the VREGENZ pin to a logic low voltage. For applications supplying VDD externally (external VREG), disable the internal VREG by tying the VREGENZ pin high. Note Not all device packages have VREGENZ pinned out. For packages without VREGENZ, external VREG mode is not supported.
6.13.1.3 External Components
6.13.1.3.1 Decoupling Capacitors
VDDIO and VDD require decoupling capacitors for correct operation. The requirements are outlined in subsequent sections. Place a minimum amount of decoupling capacitance on VDDIO. See the C VDDIO parameter in Power Management Module Electrical Data and Timing . The actual amount of decoupling capacitance to use is a requirement of the power supply driving VDDIO. Either of the configurations outlined below is acceptable:
- Configuration 1: Place a decoupling capacitor on each VDDIO pin per the CVDDIO parameter.
- Configuration 2: Install a single decoupling capacitor that is the equivalent of CVDDIO * VDDIO pins. Note Having the decoupling capacitor or capacitors close to the device pins is critical. Place a minimum amount of decoupling capacitance on VDD. See the C VDD TOTAL parameter in Power Management Module Electrical Data and Timing. www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 79 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
In external VREG mode, the actual amount of decoupling capacitance to use is a requirement of the power supply driving VDD. Either of the configurations outlined below is acceptable:
- Configuration 1: Divide CVDD TOTAL equally across the VDD pins. In this configuration, the VDD pins may be separated at the PCB level.
- Configuration 2: Install a single decoupling capacitor with value of CVDD TOTAL. In this configuration, all VDD pins must be connected to each other on the PCB. Note Having the decoupling capacitor or capacitors close to the device pins is critical.
6.13.1.4 Power Sequencing
6.13.1.4.1 Supply Pins Ganging
Connecting all 3.3-V rails together and supplying from a single source are strongly recommended. This list includes:
- VDDIO
- VDDA In addition, connect all power pins to avoid leaving any unconnected. In external VREG mode, the VDD pins should be tied together and supplied from a single source. In internal VREG mode, tying the VDD pins together is optional as long as each VDD pin has a capacitor connected to pin. See the VDD Decoupling section for VDD decoupling configurations. The analog modules on the device have fairly high PSRR; therefore, in most cases, noise on VDDA will have to exceed the recommended operating conditions of the supply rails before the analog modules see performance degradation. Therefore, supplying VDDA separately typically offers minimal benefits. Nevertheless, for the purposes of noise improvement, placing a pi filter between VDDIO and VDDA is acceptable. Note All the supply pins per rail are tied together internally. For example, all VDDIO pins are tied together internally, all VDD pins are tied together internally, and so forth.
6.13.1.4.2 Signal Pins Power Sequence
Before powering the device, do not apply voltage larger than 0.3 V above VDDIO or 0.3 V below VSS to any digital pin and 0.3 V above VDDA or 0.3 V below VSSA to any analog pin (including VREFHI). Simply, the signal pins should only be driven after XRSn goes high, provided all the 3.3-V rails are tied together. This sequencing is still required even if VDDIO and VDDA are not tied together. CAUTION If the above sequence is violated, device malfunction and possibly damage can occur as current will flow through unintended parasitic paths in the device.
6.13.1.4.3 Supply Pins Power Sequence
Figure 6-3 depicts the power sequencing requirements for external VREG mode. The values for all the parameters indicated can be found in Power Management Module Electrical Data and Timing. TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
80 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
(A) SRVDDIO-UP SRVDD-UP VPOR-VDDIO VPOR-VDD-UP (A) VDDIO VDD Internal All Monitors Release Signal(C) XRSn VXRSn-PU-DELAY VDDIO VDD Internal All Monitors Release Signal(D) SRVDDIO-DNSRVDD-DN VBOR-VDDIO-DN (B) VPOR-VDDIOVPOR-VDD-DN (B) XRSn VXRSn-PD-DELAYVDDIO-MON-TOT-DELAY A. This trip point is the trip point before XRSn releases. See the Power Management Module Characteristics table. B. This trip point is the trip point after XRSn releases. See the Power Management Module Characteristics table. C. During power up, the All Monitors Release Signal goes high after all POR and BOR monitors are released. See the PMM Block Diagram. D. During power down, the All Monitors Release Signal goes low if any of the POR or BOR monitors are tripped. See the PMM Block Diagram. Figure 6-3. External VREG Power Up Sequence
- For Power Up: 1. VDDIO (that is, the 3.3-V rail) should come up first with the minimum slew rate specified. 2. VDD (that is, the 1.2-V rail) should come up next with the minimum slew rate specified. 3. The time delta between the VDDIO rail coming up and when the VDD rail can come up is also specified. 4. After the times specified by VDDIO-MON-TOT-DELAY and VXRSN-PD-DELAY, XRSn will be released and the device starts the boot-up sequence. 5. The I/O BOR monitor has different release points during power up and power down. 6. During power up, both VDDIO and VDD rails have to be up before XRSn releases.
- For Power Down: 1. There is no requirement between VDDIO and VDD on which should power down first; however, there is a minimum slew rate specification. 2. The I/O BOR monitor has different release points during power up and power down. 3. Any of the POR or BOR monitors that trips during power down will cause XRSn to go low after VXRSN-PD-DELAY. Note The All Monitors Release Signal is an internal signal. Note If there is an external circuit driving XRSn (for example, a supervisor), the boot-up sequence does not start until the XRSn pin is released by all internal and external sources. Figure 6-4 depicts the power sequencing requirements for internal VREG mode. The values for all the parameters indicated can be found in Power Management Module Electrical Data and Timing. www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 81 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
(A) SRVDDIO-UP VPOR-VDDIO VDDIO Internal All Monitors Release Signal(C) XRSn VXRSn-PU-DELAY VDDIO Internal All Monitors Release Signal(D) SRVDDIO-DN VBOR-VDDIO-DN (B) VPOR-VDDIO XRSn VXRSn-PD-DELAYVDDIO-MON-TOT-DELAY A. This trip point is the trip point before XRSn releases. See the Power Management Module Characteristics table. B. This trip point is the trip point after XRSn releases. See the Power Management Module Characteristics table. C. During power up, the All Monitors Release Signal goes high after all POR and BOR monitors are released. See the PMM Block Diagram. D. During power down, the All Monitors Release Signal goes low if any of the POR or BOR monitors are tripped. See the PMM Block Diagram. Figure 6-4. Internal VREG Power Up Sequence
- For Power Up: 1. VDDIO (that is, the 3.3-V rail) should come up with the minimum slew rate specified. 2. The Internal VREG powers up after the I/O monitors (I/O POR and I/O BOR) are released. 3. After the times specified by VDDIO-MON-TOT-DELAY and VXRSN-PU-DELAY, XRSn will be released and the device starts the boot-up sequence. 4. The I/O BOR monitor has different release points during power up and power down.
- For Power Down: 1. The only requirement on VDDIO during power down is the slew rate. 2. The I/O BOR monitor has different release points during power up and power down. 3. The I/O BOR tripping will cause XRSn to go low after VXRSN-PD-DELAY and also power down the Internal VREG. Note The All Monitors Release Signal is an internal signal. Note If there is an external circuit driving XRSn (for example, a supervisor), the boot-up sequence does not start until the XRSn pin is released by all internal and external sources. The acceptable power-up sequence for the rails is summarized below. "Power up" here means the rail in question has reached the minimum recommended operating voltage. CAUTION Non-acceptable sequences leads to reliability concerns and possibly damage. For simplicity, connecting all 3.3-V rails together and following the descriptions in Supply Pins Power Sequence is recommended. TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
82 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 6-1. External VREG Sequence Summary CASE RAILS POWER-UP ORDER ACCEPTABLE VDDIO VDDA VDD A 1 2 3 Yes B 1 3 2 Yes C 2 1 3 - D 2 3 1 - E 3 2 1 - F 3 1 2 - G 1 1 2 Yes H 2 2 1 - Table 6-2. Internal VREG Sequence Summary CASE RAILS POWER-UP ORDER ACCEPTABLE VDDIO VDDA A 1 2 Yes B 2 1 - C 1 1 Yes Note The analog modules on the device should only be powered after VDDA has reached the minimum recommended operating voltage. VDDIO has a minimum slew rate requirement. If the minimum slew rate is not met, XRSn might toggle a few times until VDDIO crosses the I/O BOR region. Note The toggling on XRSn has no adverse effect on the device as boot only starts once XRSn is steadily high. However if XRSn from the device is used to gate the reset signal of other ICs, then the slew rate requirement should be met to prevent this toggling. VDD has a minimum slew rate requirement in external VREG mode. If the minimum slew rate is not met, the VDD POR may release before the VDD operational minimum voltage is met and the device may not start in a properly reset state. www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 83 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.13.1.5 Power Management Module Electrical Data and Timing
6.13.1.5.1 Power Management Module Operating Conditions
over recommended operating conditions (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT General CVDDIO (1) (2) VDDIO Capacitance Per Pin(7) 0.1 uF CVDDA (1) (2) VDDA Capacitance Per Pin(7) 2.2 uF SRVDD33 (3) Supply Ramp Rate of 3.3V Rails (VDDIO, VDDA) 20 100 mV/us VBOR-VDDIO-GB (5) VDDIO Brown Out Reset Voltage Guardband 0.1 V External VREG CVDD TOTAL(1) (4) Total VDD Capacitance(7) 10 uF SRVDD12 (3) Supply Ramp Rate of 1.2V Rail (VDD) 10 100 mV/us VDDIO - VDD Delay(6) Ramp Delay Between VDDIO and VDD 0 us Internal VREG CVDD TOTAL(1) (4) Total Nominal VDD Capacitance(7) 10 22 uF (1) A bulk capacitor should also be used. The exact value of the decoupling capacitance depends on the system voltage regulation solution that is supplying these pins. (2) It is recommended to tie the 3.3V rails (VDDIO, VDDA) together and supply them from a single source. (3) See the Supply Slew Rate section. Supply ramp rate faster than the maximum can trigger the on-chip ESD protection. (4) See the Power Management Module (PMM) section on possible configurations for the total decoupling capacitance. (5) TI recommends VBOR-VDDIO-GB to avoid BOR-VDDIO resets due to normal supply noise or load-transient events on the 3.3-V VDDIO system regulator. Good system regulator design and decoupling capacitance (following the system regulator specifications) are important to prevent activation of the BOR-VDDIO during normal device operation. The value of VBOR-VDDIO-GB is a system-level design consideration; the voltage listed here is typical for many applications. (6) Delay between when the 3.3-V rail ramps up and when the 1.2-V rail ramps up. See the VREG Sequence Summary table for the allowable supply ramp sequences. (7) Max capacitor tolerance should be 20%.
6.13.1.5.2 Power Management Module Characteristics
over recommended operating conditions (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT VVREG Internal Voltage Regulator Output 1.152 1.2 1.248 V VVREG-PU Internal Voltage Regulator Power Up Time 350 us VVREG-INRUSH (4) Internal Voltage Regulator Inrush Current 650 mA VPOR-VDDIO VDDIO Power on Reset Voltage Before and After XRSn Release 2.3 V VBOR-VDDIO-UP (1) VDDIO Brown Out Reset Voltage on Ramp Up Before XRSn Release 2.7 V VBOR-VDDIO- DOWN (1) VDDIO Brown Out Reset Voltage on Ramp Down After XRSn Release 2.81 3.0 V VXRSn-PU- DELAY (2) XRSn Release Delay after Supplies are Ramped Up During Power-Up 40 us TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
84 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.13.1.5.2 Power Management Module Characteristics (continued)
over recommended operating conditions (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT VXRSn-PD- DELAY (3) XRSn Trip Delay after Supplies are Ramped Down During Power-Down 2 us VDDIO-MON- TOT-DELAY Total Delays in Path of VDDIO Monitors (POR, BOR) 80 us VXRSn-MON- RELEASE-DELAY XRSn Release Delay after a VDD POR Event Supplies Within Operating Range 40 us XRSn Release Delay after a VDDIO BOR Event 40 us XRSn Release Delay after a VDDIO POR Event 120 us (1) See the I/O BOR Operating Region figure. (2) Supplies are considered fully ramped up after they cross the minimum recommended operating conditions for the respective rail. All POR and BOR monitors need to be released before this delay takes effect. (3) On power down, any of the POR or BOR monitors that trips will immediately trip XRSn. This delay is the time between any of the POR, BOR monitors tripping and XRSn going low. It is variable and depends on the ramp down rate of the supply. (4) This is the transient current drawn on the VDDIO rail when the internal VREG turns on. Due to this, there might be some voltage drops on the VDDIO rail when the VREG turns on which could cause the VREG to ramp up in steps. There is no detriment to the device from this but the effect can be reduced if desired by using sufficient decoupling capacitors on VDDIO or picking an LDO/DC-DC that can supply this transient current. www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 85 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.13.2 Reset Timing
XRSn is the device reset pin. It functions as an input and open-drain output. The device has a built-in power-on reset (POR) and brown-out reset (BOR) monitors. During power up, the monitor circuits keep the XRSn pin low. For more details, see the Power Management Module (PMM) section. A watchdog or NMI watchdog reset will also drive the pin low. An external open-drain circuit may drive the pin to assert a device reset. A resistor with a value from 2.2 k Ω to 10 k Ω should be placed between XRSn and VDDIO. A capacitor should be placed between XRSn and VSS for noise filtering, it should be 100 nF or smaller. These values will allow the watchdog to properly drive the XRSn pin to V OL within 512 OSCCLK cycles when the watchdog reset is asserted. Figure 6-5 shows the recommended reset circuit. XRSn Optional open-drain Reset source /c163100 nF 2.2 k to 10 k/c87 /c87 VDDIO Figure 6-5. Reset Circuit
6.13.2.1 Reset Sources
The Reset Signals table summarizes the various reset signals and their effect on the device. Table 6-3. Reset Signals Reset Source CPU Core Reset (C28x, FPU, TMU) Peripherals Reset JTAG / Debug Logic Reset IOs XRS Output POR Yes Yes Yes Hi-Z Yes BOR Yes Yes Yes Hi-Z Yes XRS Pin Yes Yes No Hi-Z - WDRS Yes Yes No Hi-Z Yes NMIWDRS Yes Yes No Hi-Z Yes SYSRS (Debugger Reset) Yes Yes No Hi-Z No SCCRESET Yes Yes No Hi-Z No SIMRESET. XRS Yes Yes No Hi-Z Yes SIMRESET. CPU1RS Yes Yes No Hi-Z No The parameter th(boot-mode) must account for a reset initiated from any of these sources. See the Resets section of the System Control chapter in the TMS320F28P55x Real-Time Microcontrollers Technical Reference Manual. CAUTION Some reset sources are internally driven by the device. Some of these sources will drive XRSn low, use this to disable any other devices driving the boot pins. The SCCRESET and debugger reset sources do not drive XRSn; therefore, the pins used for boot mode should not be actively driven by other devices in the system. The boot configuration has a provision for changing the boot pins in OTP. TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
86 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.13.2.2 Reset Electrical Data and Timing
6.13.2.2.1 Reset - XRSn - Timing Requirements
th(boot-mode) Hold time for boot-mode pins 1.5 ms tw(RSL2) Pulse duration, XRSn low on warm reset 3.2 µs
6.13.2.2.2 Reset - XRSn - Switching Characteristics
over recommended operating conditions (unless otherwise noted) PARAMETER MIN TYP MAX UNIT tw(RSL1) Pulse duration, XRSn driven low by device after supplies are stable 100 µs tw(WDRS) Pulse duration, reset pulse generated by watchdog 512tc(OSCCLK) cycles tboot-flash Boot-ROM execution time to first instruction fetch in flash 1.2 ms
6.13.2.2.3 Reset Timing Diagrams
(3.3V) VDD (1.2V) XRSn(A) CPU Execution Phase Boot-Mode Pins I/O Pins th(boot-mode) (B) Boot ROM User code User code dependent GPIO pins as input Boot-ROM execution starts GPIO pins as input (pullups are disabled) User code dependent Peripheral/GPIO function Based on boot code tw(RSL1) tboot-flash A. The XRSn pin can be driven externally by a supervisor or an external pullup resistor, see the Pin Attributes table. On-chip monitors will hold this pin low until the supplies are in a valid range. B. After reset from any source (see the Reset Sources section), the boot ROM code samples Boot Mode pins. Based on the status of the Boot Mode pin, the boot code branches to destination memory or boot code function. If boot ROM code executes after power-on conditions (in debugger environment), the boot code execution time is based on the current SYSCLK speed. The SYSCLK will be based on user environment and could be with or without PLL enabled. Figure 6-6. Power-on Reset www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 87 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
tw(RSL2) Boot-Mode Pins User-Code Execution Starts Peripheral/GPIO function Boot ROM execution starts (initiated by any reset source) Peripheral/GPIO function GPIO Pins as Input th(boot-mode) (A) I/O Pins User-Code Dependent GPIO Pins as Input (Pullups are Disabled) User-Code Dependent A. After reset from any source (see the Reset Sources section), the Boot ROM code samples BOOT Mode pins. Based on the status of the Boot Mode pin, the boot code branches to destination memory or boot code function. If Boot ROM code executes after power-on conditions (in debugger environment), the Boot code execution time is based on the current SYSCLK speed. The SYSCLK will be based on user environment and could be with or without PLL enabled. Figure 6-7. Warm Reset TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
88 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.13.3 Clock Specifications
6.13.3.1 Clock Sources
Table 6-4. Possible Reference Clock Sources CLOCK SOURCE DESCRIPTION INTOSC1 Internal oscillator 1. 10-MHz internal oscillator. INTOSC2(1) Internal oscillator 2. 10-MHz internal oscillator. X1 (XTAL) External crystal or resonator connected between the X1 and X2 pins or single-ended clock connected to the X1 pin. (1) On reset, internal oscillator 2 (INTOSC2) is the default clock source for the PLL (OSCCLK). www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 89 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
X1 (XTAL) OSCCLK PLLRAWCLK SYS Divider Watchdog Timer SYSCLKDIVSEL NMIWD CPU OSCCLKRCSEL FPU TMU Boot ROM ePIE FLASH GPIO CLA ROM DCSM XINT WD SYSCLK Flash Wrapper Clock Divider KDIV CPUCLK FLCLK Flash Wrapper SYSCLK CLA CPUTIMERs EPWM ECAP EQEP HRCAL ADC CMPSS GPDAC PGA DCC PMBUS USB PERx.SYSCLK PCLKCRx One per SYSCLK peripheral PCLKCRx One per SYSCLK peripheral LSP Divider LSPCLKDIV SCI SPI PERx.LSPCLKLSPCLK CLKSRCCTL2.MCANxBCLKSEL MCAN Bit Clock PLLSYSCLK GSx RAMs LSx RAMs Mx RAMs Message RAM System Control Reserved /20 AUXCLKDIVSEL.MCANxCLKDIV AES CLB ERAD EPG FSI I2C PLLRAWCLK AUXCLKIN(GPIO29) WDCLK PLLCLKEN USBBITCLK PERCLKDIVSEL.USBCLKDIV PLLCLK PCLKCRx One per SYSCLK peripheral LIN Clock Divider LINACLKDIV PERx.LINACLKLINACLK LIN CLBCLKCTL /1 or /2 CLB_TILE_CLK CLB_REG_CLK SYSCLK SYSCLK PCLKCRx One per SYSCLK peripheral NNPU Clock Divider NNPUCLKDIV NNPU PERx.NNPUCLKNNPUCLK Figure 6-8. Clocking System TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
90 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
(REFDIV+1) VCO IMULT (ODIV+1) PLLRAWCLKVCOCLKINTCLKOSCCLK SYSPLL Figure 6-9. System PLL In the System PLL figure, f PL L R A WC L K = f O SC CL K R EF DI V + 1 × I MU L T ODI V + 1 (1) www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 91 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.13.3.2 Clock Frequencies, Requirements, and Characteristics
This section provides the frequencies and timing requirements of the input clocks, PLL lock times, frequencies of the internal clocks, and the frequency and switching characteristics of the output clock.
6.13.3.2.1 Input Clock Frequency and Timing Requirements, PLL Lock Times
f(XTAL) Frequency, X1/X2, from external crystal or resonator 10 20 MHz f(X1) Frequency, X1, from external oscillator 10 25 MHz over recommended operating conditions (unless otherwise noted) PARAMETER MIN TYP MAX UNIT X1 VIL Valid low-level input voltage –0.3 0.3 * VDDIO V X1 VIH Valid high-level input voltage 0.7 * VDDIO VDDIO + 0.3 V over recommended operating conditions (unless otherwise noted) PARAMETER MIN MAX UNIT X1 VIL Valid low-level input voltage (Buffer) –0.3 0.3 * VDDIO V X1 VIH Valid high-level input voltage (Buffer) 0.7 * VDDIO VDDIO + 0.3 V MIN MAX UNIT tf(X1) Fall time, X1 6 ns tr(X1) Rise time, X1 6 ns tw(X1L) Pulse duration, X1 low as a percentage of tc(X1) 45% 55% tw(X1H) Pulse duration, X1 high as a percentage of tc(X1) 45% 55% MIN MAX UNIT tf(AUXI) Fall time, AUXCLKIN 6 ns tr(AUXI) Rise time, AUXCLKIN 6 ns tw(AUXL) Pulse duration, AUXCLKIN low as a percentage of tc(XCI) 45% 55% tw(AUXH) Pulse duration, AUXCLKIN high as a percentage of tc(XCI) 45% 55% over recommended operating conditions (unless otherwise noted) PARAMETER MIN TYP MAX UNIT PLL Lock time SYS PLL Lock Time(1) 5µs + (1024 * (REFDIV + 1) * tc(OSCCLK)) us (1) The PLL lock time here defines the typical time that takes for the PLL to lock once PLL is enabled (SYSPLLCTL1[PLLENA]=1). Additional time to verify the PLL clock using Dual Clock Comparator (DCC) is not accounted here. TI recommends using the latest example software from C2000Ware for initializing the PLLs. For the system PLL, see InitSysPll() or SysCtl_setClock(). TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
92 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
over recommended operating conditions (unless otherwise noted) PARAMETER(1) MIN MAX UNIT tf(XCO) Fall time, XCLKOUT 6 ns tr(XCO) Rise time, XCLKOUT 6 ns tw(XCOL) Pulse duration, XCLKOUT low H – 2(2) H + 2(2) ns tw(XCOH) Pulse duration, XCLKOUT high H – 2(2) H + 2(2) ns f(XCO) Frequency, XCLKOUT 50 MHz (1) A load of 6 pF is assumed for these parameters. (2) H = 0.5tc(XCO) MIN NOM MAX UNIT f(SYSCLK) Frequency, device (system) clock 2 150 MHz tc(SYSCLK) Period, device (system) clock 6.67 500 ns f(INTCLK) Frequency, system PLL going into VCO (after REFDIV) 2 20 MHz f(VCOCLK) Frequency, system PLL VCO (before ODIV) 220 600 MHz f(PLLRAWCLK) Frequency, system PLL output (before SYSCLK divider) 6 300 MHz f(PLL) Frequency, PLLSYSCLK 2 150 MHz f(PLL_LIMP) Frequency, PLL Limp Frequency (1) 45/(ODIV+1) MHz f(LSP) Frequency, LSPCLK 2 150 MHz tc(LSPCLK) Period, LSPCLK 6.67 500 ns f(OSCCLK) Frequency, OSCCLK (INTOSC1 or INTOSC2 or XTAL or X1) See respective clock MHz f(EPWM) Frequency, EPWMCLK 150 MHz f(HRPWM) Frequency, HRPWMCLK 60 150 MHz (1) PLL output frequency when OSCCLK is dead (Loss of OSCCLK causes PLL to Limp). www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 93 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.13.3.3 Input Clocks and PLLs
In addition to the internal 0-pin oscillators, three types of external clock sources are supported:
- A single-ended 3.3-V external clock. The clock signal should be connected to X1, as shown in Figure 6-10, with the XTALCR.SE bit set to 1.
- An external crystal. The crystal should be connected across X1 and X2 with its load capacitors connected to VSS as shown in Figure 6-11.
- An external resonator. The resonator should be connected across X1 and X2 with its ground connected to VSS as shown in Figure 6-12. X1 X2VSS Microcontroller 3.3-V Oscillator VDD Out Gnd +3.3 V GPIO18* * Available as a GPIO when X1 is used as a clock GPIO19 Figure 6-10. Single-ended 3.3-V External Clock X1 X2VSS Microcontroller GPIO18GPIO19 Figure 6-11. External Crystal X1 X2VSS Microcontroller GPIO18GPIO19 Figure 6-12. External Resonator
6.13.3.4 XTAL Oscillator
6.13.3.4.1 Introduction
The crystal oscillator in this device is an embedded electrical oscillator that, when paired with a compatible quartz crystal (or a ceramic resonator), can generate the system clock required by the device.
6.13.3.4.2 Overview
The following sections describe the components of the electrical oscillator and crystal. The electrical oscillator in this device is a Pierce oscillator. It is a positive feedback inverter circuit that requires a tuning circuit in order to oscillate. When this oscillator is paired with a compatible crystal, a tank circuit is formed. This tank circuit oscillates at the fundamental frequency of the crystal. On this device, the oscillator is designed to operate in parallel resonance mode due to the shunt capacitor (C0) and required load capacitors (CL). Figure 6-13 illustrates the components of the electrical oscillator and the tank circuit. TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
94 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
[XTAL On] Crystal Rbias Pierce Inverter Figure 6-13. Electrical Oscillator Block Diagram The electrical oscillator in this device has two modes of operation: crystal mode and single-ended mode. In the crystal mode of operation, a quartz crystal with load capacitors has to be connected to X1 and X2. This mode of operation is engaged when [XTAL On] = 1, which is achieved by setting XTALCR.OSCOFF = 0 and XTALCR.SE = 0. There is an internal bias resistor for the feedback loop so an external one should not be used. Adding an external bias resistor will create a parallel resistance with the internal Rbias, moving the bias point of operation and possibly leading to clipped waveforms, out-of-specification duty cycle, and reduction in the effective negative resistance. In this mode of operation, the resultant clock on X1 is passed through a comparator (Comp) to the rest of the chip. The clock on X1 needs to meet the VIH and VIL of the comparator. See the XTAL Oscillator Characteristics table for the VIH and VIL requirements of the comparator. In the single-ended mode of operation, a clock signal is connected to X1 with X2 left unconnected. A quartz crystal should not be used in this mode. This mode is enabled when [XTAL On] = 0, which can be achieved by setting XTALCR.OSCOFF = 1 and XTALCR.SE = 1. www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 95 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
In this mode of operation, the clock on X1 is passed through a buffer (Buffer) to the rest of the chip. See the X1 Input Level Characteristics When Using an External Clock Source (Not a Crystal) table for the input requirements of the buffer. The output of the electrical oscillator that is fed to the rest of the chip can be brought out on XCLKOUT for observation by configuring the CLKSRCCTL3.XCLKOUTSEL and XCLKOUTDIVSEL.XCLKOUTDIV registers. See the GPIO Muxed Pins table for a list of GPIOs that XCLKOUT comes out on. Electrically, a quartz crystal can be represented by an LCR (Inductor-Capacitor-Resistor) circuit. However, unlike an LCR circuit, crystals have very high Q due to the low motional resistance and are also very underdamped. Components of the crystal are shown in Figure 6-14 and explained below. Cm Rm Lm C0 CL Quartz Crystal ExternalInternal Figure 6-14. Crystal Electrical Representation Cm (Motional capacitance): Denotes the elasticity of the crystal. Rm (Motional resistance): Denotes the resistive losses within the crystal. This is not the ESR of the crystal but can be approximated as such depending on the values of the other crystal components. Lm (Motional inductance): Denotes the vibrating mass of the crystal. C0 (Shunt capacitance): The capacitance formed from the two crystal electrodes and stray package capacitance. CL (Load capacitance): This is the effective capacitance seen by the crystal at its electrodes. It is external to the crystal. The frequency ppm specified in the crystal data sheet is usually tied to the CL parameter. Note that most crystal manufacturers specify CL as the effective capacitance seen at the crystal pins, while some crystal manufacturers specify CL as the capacitance on just one of the crystal pins. Check with the crystal manufacturer for how the CL is specified in order to use the correct values in calculations. From Figure 6-13, CL1 and CL2 are in series; so, to find the equivalent total capacitance seen by the crystal, the capacitance series formula has to be applied which simply evaluates to [CL1]/2 if CL1 = CL2. It is recommended that a stray PCB capacitance be added to this value. 3 pF to 5 pF are reasonable estimates, but the actual value will depend on the PCB in question. Note that the load capacitance is a requirement of both the electrical oscillator and crystal. The value chosen has to satisfy both the electrical oscillator and the crystal. TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
96 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
The effect of CL on the crystal is frequency-pulling. If the effective load capacitance is lower than the target, the crystal frequency will increase and vice versa. However, the effect of frequency-pulling is usually very minimal and typically results in less than 10-ppm variation from the nominal frequency. On this device, X1 and X2 can be used as GPIO19 and GPIO18, respectively, depending on the operating mode of the XTAL. Refer to the External Oscillator (XTAL) section of the TMS320F28P55x Real-Time Microcontrollers Technical Reference Manual .
6.13.3.4.3 Functional Operation
Effective Series Resistance is the resistive load the crystal presents to the electrical oscillator at resonance. The higher the ESR, the lower the Q, and less likely the crystal will start up or maintain oscillation. The relationship between ESR and the crystal components is indicated below. E SR = Rm * 1 + C 0 CL 2 (2) Note that ESR is not the same as motional resistance of the crystal, but can be approximated as such if the effective load capacitance is much greater than the shunt capacitance. Negative resistance is the impedance presented by the electrical oscillator to the crystal. It is the amount of energy the electrical oscillator must supply to the crystal to overcome the losses incurred during oscillation. Rneg depicts a circuit that provides rather than consume energy and can also be viewed as the overall gain of the circuit. The generally accepted practice is to have Rneg > 3x ESR to 5x ESR to ensure the crystal starts up under all conditions. Note that it takes slightly more energy to start up the crystal than it does to sustain oscillation; therefore, if it can be ensured that the negative resistance requirement is met at start-up, then oscillation sustenance will not be an issue. Figure 6-15 and Figure 6-16 show the variation between negative resistance and the crystal components for this device. As can be seen from the graphs, the crystal shunt capacitance (C0) and effective load capacitance (CL) greatly influence the negative resistance of the electrical oscillator. Note that these are typical graphs; so, refer to Table 6-5 for minimum and maximum values for design considerations. Start-up time is an important consideration when selecting the components of the crystal circuit. As mentioned in the Rneg – Negative Resistance section, for reliable start-up across all conditions, it is recommended that the Rneg > 3x ESR to 5x ESR of the crystal. Crystal ESR and the dampening resistor (Rd) greatly affect the start-up time. The higher the two values, the longer the crystal takes to start up. Longer start-up times are usually a sign that the crystal and components are not a correct match. Refer to Crystal Oscillator Specifications for the typical start-up times. Note that the numbers specified here are typical numbers provided for guidance only. Actual start-up time depends heavily on the crystal in question and the external components. On this device, the GPIO19/18 alternate functionality on X1/X2 can be used to speed up the start-up time of the crystal if needed. This functionality is achieved by preconditioning the load capacitors CL1 and CL2 to a known state before the XTAL is turned on. See the TMS320F28P55x Real-Time Microcontrollers Technical Reference Manual for details. www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 97 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Drive level refers to how much power is provided by the electrical oscillator and dissipated by the crystal. The maximum drive level specified in the crystal manufacturer’s data sheet is usually the maximum the crystal can dissipate without damage or significant reduction in operating life. On the other hand, the drive level specified by the electrical oscillator is the maximum power it can provide. The actual power provided by the electrical oscillator is not necessarily the maximum power and depends on the crystal and board components. For cases where the actual drive level from the electrical oscillator exceeds the maximum drive level specification of the crystal, a dampening resistor (Rd) should be installed to limit the current and reduce the power dissipated by the crystal. Note that Rd reduces the circuit gain; and therefore, the actual value to use should be evaluated to make sure all other conditions for start-up and sustained oscillation are met.
6.13.3.4.4 How to Choose a Crystal
Using Crystal Oscillator Specifications as a reference: 1. Pick a crystal frequency (for example, 20 MHz). 2. Check that the ESR of the crystal <=50 Ω per specifications for 20 MHz. 3. Check that the load capacitance requirement of the crystal manufacturer is within 6 pF and 12 pF per specifications for 20 MHz.
- As mentioned, CL1 and CL2 are in series; so, provided CL1 = CL2, effective load capacitance CL = [CL1]/2.
- Adding board parasitics to this results in CL = [CL1]/2 + Cstray 4. Check that the maximum drive level of the crystal >= 1 mW. If this requirement is not met, a dampening resistor Rd can be used. Refer to DL – Drive Level on other points to consider when using Rd.
6.13.3.4.5 Testing
It is recommended that the user have the crystal manufacturer completely characterize the crystal with their board to ensure the crystal always starts up and maintains oscillation. Below is a brief overview of some measurements that can be performed: Due to how sensitive the crystal circuit is to capacitance, it is recommended that scope probes not be connected to X1 and X2. If scope probes must be used to monitor X1/X2, an active probe with less than 1-pF input capacitance should be used. Frequency 1. Bring out the XTAL on XCLKOUT. 2. Measure this frequency as the crystal frequency. Negative Resistance 1. Bring out the XTAL on XCLKOUT. 2. Place a potentiometer in series with the crystal between the load capacitors. 3. Increase the resistance of the potentiometer until the clock on XCLKOUT stops. 4. This resistance plus the crystal’s actual ESR is the negative resistance of the electrical oscillator. Start-Up Time 1. Turn off the XTAL. 2. Bring out the XTAL on XCLKOUT. 3. Turn on the XTAL and measure how long it takes the clock on XCLKOUT to stay within 45% and 55% duty cycle.
6.13.3.4.6 Common Problems and Debug Tips
- Go through the How to Choose a Crystal section and make sure there are no violations. TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
98 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Crystal Takes a Long Time to Start Up
- If a dampening resistor Rd is installed, it is too high.
- If no dampening resistor is installed, either the crystal ESR is too high or the overall circuit gain is too low due to high load capacitance.
6.13.3.4.7 Crystal Oscillator Specifications
over recommended operating conditions (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT Start-up time(1) f = 10 MHz ESR MAX = 110 Ω CL1 = CL2 = 24 pF C0 = 7 pF 4 ms f = 20 MHz ESR MAX = 50 Ω CL1 = CL2 = 24 pF C0 = 7 pF 2 ms Crystal drive level (DL) 1 mW (1) Start-up time is dependent on the crystal and tank circuit components. TI recommends that the crystal vendor characterize the application with the chosen crystal. For the Crystal Equivalent Series Resistance (ESR) Requirements table: 1. Crystal shunt capacitance (C0) should be less than or equal to 7 pF. 2. ESR = Negative Resistance/3 Table 6-5. Crystal Equivalent Series Resistance (ESR) Requirements CRYSTAL FREQUENCY (MHz) MAXIMUM ESR (Ω) (CL1 = CL2 = 12 pF) MAXIMUM ESR (Ω) (CL1 = CL2 = 24 pF) 10 55 110 12 50 95 14 50 90 16 45 75 18 45 65 20 45 50 Effective CL (pF) Rneg (Ohms) Negative Resistance vs. 10MHz Crystal 2 4 6 8 10 12 14 16 500 1000 1500 2000 2500 3000 C0 (pF) Figure 6-15. Negative Resistance Variation at 10 MHz www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 99 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Effective CL (pF) Rneg (Ohms) Negative Resistance vs. 20MHz Crystal 2 4 6 8 10 12 14 16 200 400 600 800 1000 1200 1400 1600 C0 (pF) Figure 6-16. Negative Resistance Variation at 20 MHz MIN MAX UNIT CL1, CL2 Load capacitance 12 24 pF C0 Crystal shunt capacitance 7 pF over recommended operating conditions (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT Start-up time(1) f = 10 MHz ESR MAX = 110 Ω CL1 = CL2 = 24 pF C0 = 7 pF 4 ms f = 20 MHz ESR MAX = 50 Ω CL1 = CL2 = 24 pF C0 = 7 pF 2 ms Crystal drive level (DL) 1 mW (1) Start-up time is dependent on the crystal and tank circuit components. TI recommends that the crystal vendor characterize the application with the chosen crystal. TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
100 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.13.3.5 Internal Oscillators
To reduce production board costs and application development time, all devices contain two independent internal oscillators, referred to as INTOSC1 and INTOSC2. By default, INTOSC2 is set as the source for the system reference clock (OSCCLK) and INTOSC1 is set as the backup clock source. Applications requiring tighter SCI baud rate matching can use the SCI baud tuning example (baud_tune_via_uart) available in C2000Ware.
6.13.3.5.1 INTOSC Characteristics
over recommended operating conditions (unless otherwise noted) PARAMETER PART PACKAGE SUFFIX TEST CONDITIONS MIN TYP MAX UNIT fINTOSC Frequency, INTOSC1 and INTOSC2(1) All All fINTOSC- STABILITY Frequency stability at room temperature All All 30°C, Nominal VDD ±0.1 % tINTOSC-ST Start-up and settling time All All 20 µs (1) INTOSC frequency may shift due to the thermal and mechanical stress of solder reflow. A post-reflow bake can restore the unit to its original data sheet performance. www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 101 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.13.4 Flash Parameters
Table 6-6 lists the minimum required Flash wait states with different clock sources and frequencies. Wait state is the value set in register FRDCNTL[RWAIT]. Table 6-6. Minimum Required Flash Wait States with Different Clock Sources and Frequencies CPUCLK (MHz) Wait States (FRDCNTLRWAIT) 120 < CPUCLK ≤ 150 3 80 < CPUCLK ≤ 120 2 0 < CPUCLK ≤ 80 1 (1) Minimum required FRDCNTL[RWAIT] is 1, RWAIT=0 is not supported. The F28P55x devices have a 128-bit prefetch buffer that provides high flash code execution efficiency across wait states. Figure 6-17 and Figure 6-18 illustrate typical efficiency across wait-state settings compared to previous-generation devices with a 64-bit prefetch buffer. Wait-state execution efficiency with a prefetch buffer will depend on how many branches are present in application software. Two examples of linear code and if-then-else code are provided. Wait State Efficiency (%) 0 1 2 3 4 5 30% 40% 50% 60% 70% 80% 90% 100% D005 Flash with 64-Bit Prefetch Flash with 128-Bit Prefetch Figure 6-17. Application Code With Heavy 32-Bit Floating-Point Math Instructions Wait State Efficiency (%) 0 1 2 3 4 5 55% 60% 65% 70% 75% 80% 85% 90% 95% 100% D006D006 Flash with 64-Bit Prefetch Flash with 128-Bit Prefetch Figure 6-18. Application Code With 16-Bit If-Else Instructions Note The Main Array flash programming must be aligned to 64-bit address boundaries and each 64-bit word may only be programmed once per write/erase cycle. TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
102 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.13.4.1 Flash Parameters
PARAMETER MIN TYP MAX UNIT Program Time(1) 128 data bits + 16 ECC bits 62.5 625 µs 2KB (Sector) 8 80 µs Erase Time(2) (3) at < 25 cycles 2KB (Sector) 15 55 ms 64KB 17 61 ms 128KB 18 66 ms 256KB 21 78 ms Erase Time(2) (3) at 1000 cycles 2KB (Sector) 25 130 ms 64KB 28 143 ms 128KB 30 157 ms 256KB 35 183 ms Erase Time(2) (3) at 2000 cycles 2KB (Sector) 30 221 ms 64KB 33 243 ms 128KB 36 265 ms 256KB 42 310 ms Erase Time(2) (3) at 20K cycles 2KB (Sector) 120 1003 ms 64KB 132 1102 ms 128KB 145 1205 ms 256KB 169 1410 ms Nwec Write/Erase Cycles per Bank (4) 100000 cycles tretention Data retention duration at TJ = 85oC 20 years (1) Program time is at the maximum device frequency. Program time includes overhead of the flash state machine but does not include the time to transfer the following into RAM:
- Code that uses flash API to program the flash
- Flash API itself
- Flash data to be programmed In other words, the time indicated in this table is applicable after all the required code/data is available in the device RAM, ready for programming. The transfer time will significantly vary depending on the speed of the JTAG debug probe used. Program time calculation is based on programming 144 bits at a time at the specified operating frequency. Program time includes Program verify by the CPU. The program time does not degrade with write/erase (W/E) cycling, but the erase time does. Erase time includes Erase verify by the CPU and does not involve any data transfer. (2) Erase time includes Erase verify by the CPU. (3) The on-chip flash memory is in an erased state when the device is shipped from TI. As such, erasing the flash memory is not required prior to programming, when programming the device for the first time. However, the erase operation is needed on all subsequent programming operations. (4) The combined total of bank and sector write/erase cycles is limited to this number www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 103 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.13.5 RAM Specifications
All volatile memory (RAM and ROM) on the F28P55x device is 0 Wait-state for both reads and writes, meaning the memory operates at the same speed as SYSCLK. Table 6-7, Table 6-8, and Table 6-9 summarize the characteristics of the different RAM instances on the device. Table 6-7. RAM Parameters – F28P55xSJ RAM TYPE SIZE FETCH TIME(1) (CYCLES) READ TIME(1) (CYCLES) STORE TIME (CYCLES) BUS WIDTH NUMBER OF BUSES AVAILABLE NUMBER OF WAIT STATES BURST ACCESS LS RAM 64KB 2 2 1 16/32 bits 2 0 No M0 2KB 2 2 1 16/32 bits 1 0 No M1 2KB 2 2 1 16/32 bits 1 0 No GS RAM 64KB 2 2 1 16/32 bits 3 0 No CLA-to-CPU Message RAM 256B 2 2 1 16/32 bits 2 0 No CPU-to-CLA Message RAM 256B 2 2 1 16/32 bits 2 0 No CLA-to-DMA Message RAM 256B 2 2 1 16/32 bits 3 0 No DMA-to-CLA Message RAM 256B 2 2 1 16/32 bits 3 0 No (1) Without arbitration between read/write/fetch. Access completes in 2 cycles; otherwise, arbitration priority (Write/Read/Fetch) is followed. Table 6-8. RAM Parameters – F28P55xSG RAM TYPE SIZE FETCH TIME(1) (CYCLES) READ TIME(1) (CYCLES) STORE TIME (CYCLES) BUS WIDTH NUMBER OF BUSES AVAILABLE NUMBER OF WAIT STATES BURST ACCESS LS RAM 64KB 2 2 1 16/32 bits 2 0 No M0 2KB 2 2 1 16/32 bits 1 0 No M1 2KB 2 2 1 16/32 bits 1 0 No GS RAM 32KB 2 2 1 16/32 bits 2 0 No CLA-to-CPU Message RAM 256B 2 2 1 16/32 bits 2 0 No CPU-to-CLA Message RAM 256B 2 2 1 16/32 bits 2 0 No CLA-to-DMA Message RAM 256B 2 2 1 16/32 bits 3 0 No DMA-to-CLA Message RAM 256B 2 2 1 16/32 bits 3 0 No (1) Without arbitration between read/write/fetch. Access completes in 2 cycles; otherwise, arbitration priority (Write/Read/Fetch) is followed. TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
104 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 6-9. RAM Parameters – F28P55xSD RAM TYPE SIZE FETCH TIME(1) (CYCLES) READ TIME(1) (CYCLES) STORE TIME (CYCLES) BUS WIDTH NUMBER OF BUSES AVAILABLE NUMBER OF WAIT STATES BURST ACCESS LS RAM 32KB 2 2 1 16/32 bits 2 0 No M0 2KB 2 2 1 16/32 bits 1 0 No M1 2KB 2 2 1 16/32 bits 1 0 No GS RAM 32KB 2 2 1 16/32 bits 2 0 No CLA-to-CPU Message RAM 256B 2 2 1 16/32 bits 2 0 No CPU-to-CLA Message RAM 256B 2 2 1 16/32 bits 2 0 No CLA-to-DMA Message RAM 256B 2 2 1 16/32 bits 3 0 No DMA-to-CLA Message RAM 256B 2 2 1 16/32 bits 3 0 No (1) Without arbitration between read/write/fetch. Access completes in 2 cycles; otherwise, arbitration priority (Write/Read/Fetch) is followed.
6.13.6 ROM Specifications
All volatile memory (RAM and ROM) on the F28P55x device is 0 Wait-state for both reads and writes, meaning the memory operates at the same speed as SYSCLK. Table 6-10 summarizes the aspects of the ROM instances on the device. Table 6-10. ROM Parameters – F28P55xSJ, F28P55xSG, and F28P55xSD ROM TYPE SIZE FETCH TIME(1) (CYCLES) READ TIME(1) (CYCLES) STORE TIME (CYCLES) BUS WIDTH NUMBER OF BUSES AVAILABLE NUMBER OF WAIT STATES BURST ACCESS Boot ROM + Secure ROM 96KB 2 2 1 16/32 bits 1 0 No CLA Data ROM 8KB 2 2 1 16/32 bits 2 0 No (1) Without arbitration between read/write/fetch. Access completes in 2 cycles; otherwise, arbitration priority (Write/Read/Fetch) is followed. www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 105 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.13.7 Emulation/JTAG
The JTAG (IEEE Standard 1149.1-1990 Standard Test Access Port and Boundary Scan Architecture) port has four dedicated pins: TMS, TDI, TDO, and TCK. The cJTAG (IEEE Standard 1149.7-2009 for Reduced-Pin and Enhanced-Functionality Test Access Port and Boundary-Scan Architecture) port is a compact JTAG interface requiring only two pins (TMS and TCK), which allows other device functionality to be muxed to the traditional GPIO35 (TDI) and GPIO37 (TDO) pins. Typically, no buffers are needed on the JTAG signals when the distance between the MCU target and the JTAG header is smaller than 6 inches (15.24 cm), and no other devices are present on the JTAG chain. Otherwise, each signal should be buffered. Additionally, for most JTAG debug probe operations at 10 MHz, no series resistors are needed on the JTAG signals. However, if high emulation speeds are expected (35 MHz or so), 22-Ω resistors should be placed in series on each JTAG signal. The PD (Power Detect) pin of the JTAG debug probe header should be connected to the board's 3.3-V supply. Header GND pins should be connected to board ground. TDIS (Cable Disconnect Sense) should also be connected to board ground. The JTAG clock should be looped from the header TCK output pin back to the RTCK input pin of the header (to sense clock continuity by the JTAG debug probe). This MCU does not support the EMU0 and EMU1 signals that are present on 14-pin and 20-pin emulation headers. These signals should always be pulled up at the emulation header through a pair of board pullup resistors ranging from 2.2 k Ω to 4.7 kΩ (depending on the drive strength of the debugger ports). Typically, a 2.2-kΩ value is used. Header pin RESET is an open-drain output from the JTAG debug probe header that enables board components to be reset through JTAG debug probe commands (available only through the 20-pin header). Figure 6-19 shows how the 14-pin JTAG header connects to the MCU’s JTAG port signals. Figure 6-20 shows how to connect to the 20-pin JTAG header. The 20-pin JTAG header pins EMU2, EMU3, and EMU4 are not used and should be grounded. For more information about hardware breakpoints and watchpoints, see Hardware Breakpoints and Watchpoints in CCS for C2000 devices. For more information about JTAG emulation, see the XDS Target Connection Guide. Note JTAG Test Data Input (TDI) is the default mux selection for the pin. The internal pullup is disabled by default. If this pin is used as JTAG TDI, the internal pullup should be enabled or an external pullup added on the board to avoid a floating input. In the cJTAG option, this pin can be used as GPIO. JTAG Test Data Output (TDO) is the default mux selection for the pin. The internal pullup is disabled by default. The TDO function will be in a tri-state condition when there is no JTAG activity, leaving this pin floating. The internal pullup should be enabled or an external pullup added on the board to avoid a floating GPIO input. In the cJTAG option, this pin can be used as GPIO. TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
106 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.13.7.1 JTAG Electrical Data and Timing
6.13.7.1.1 JTAG Timing Requirements
NO. MIN MAX UNIT 1 tc(TCK) Cycle time, TCK 66.66 ns 1a tw(TCKH) Pulse duration, TCK high (40% of tc) 26.66 ns 1b tw(TCKL) Pulse duration, TCK low (40% of tc) 26.66 ns tsu(TDI-TCKH) Input setup time, TDI valid to TCK high 7 ns tsu(TMS-TCKH) Input setup time, TMS valid to TCK high 7 th(TCKH-TDI) Input hold time, TDI valid from TCK high 7 ns th(TCKH-TMS) Input hold time, TMS valid from TCK high 7
6.13.7.1.2 JTAG Switching Characteristics
over recommended operating conditions (unless otherwise noted) NO. PARAMETER MIN MAX UNIT 2 td(TCKL-TDO) Delay time, TCK low to TDO valid 6 20 ns
6.13.7.1.3 JTAG Timing Diagram
Figure 6-21. JTAG Timing TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
108 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.13.7.2 cJTAG Electrical Data and Timing 6.13.7.2.1 cJTAG Timing Requirements NO. MIN MAX UNIT 1 tc(TCK) Cycle time, TCK 100 ns 1a tw(TCKH) Pulse duration, TCK high (40% of tc) 40 ns 1b tw(TCKL) Pulse duration, TCK low (40% of tc) 40 ns tsu(TMS-TCKH) Input setup time, TMS valid to TCK high 7 ns tsu(TMS-TCKL) Input setup time, TMS valid to TCK low 7 ns th(TCKH-TMS) Input hold time, TMS valid from TCK high 2 ns th(TCKL-TMS) Input hold time, TMS valid from TCK low 2 ns 6.13.7.2.2 cJTAG Switching Characteristics over recommended operating conditions (unless otherwise noted) NO. PARAMETER MIN MAX UNIT 2 td(TCKL-TMS) Delay time, TCK low to TMS valid 6 20 ns 5 tdis(TCKH-TMS) Delay time, TCK high to TMS disable 20 ns 6.13.7.2.3 cJTAG Timing Diagram 3 43 52 TMS Input TCK TMS TMS Input TMS Output Figure 6-22. cJTAG Timing www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 109 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.13.8 GPIO Electrical Data and Timing
The peripheral signals are multiplexed with general-purpose input/output (GPIO) signals. On reset, GPIO pins are configured as inputs. For specific inputs, the user can also select the number of input qualification cycles to filter unwanted noise glitches. The GPIO module contains an Output X-BAR which allows an assortment of internal signals to be routed to a GPIO in the GPIO mux positions denoted as OUTPUTXBARx. The GPIO module also contains an Input X-BAR which is used to route signals from any GPIO input to different IP blocks such as the ADCs, eCAPs, ePWMs, and external interrupts. For more details, see the X-BAR chapter in the TMS320F28P55x Real-Time Microcontrollers Technical Reference Manual.
6.13.8.1 GPIO – Output Timing
6.13.8.1.1 General-Purpose Output Switching Characteristics
over recommended operating conditions (unless otherwise noted) PARAMETER MIN MAX UNIT tr(GPO) Rise time, GPIO switching low to high All GPIOs 6(1) ns tf(GPO) Fall time, GPIO switching high to low All GPIOs 6(1) ns tfGPO Toggling frequency, GPIO pins All GPIOs not listed below 50 MHzGPIO 2, 3, 9, and 32 40 GPIO 23 and 41 25 (1) Rise time and fall time vary with load. These values assume a 6-pF load.
6.13.8.1.2 General-Purpose Output Timing Diagram
tf(GPO) tr(GPO) Figure 6-23. General-Purpose Output Timing TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
110 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.13.8.2 GPIO – Input Timing
6.13.8.2.1 General-Purpose Input Timing Requirements
tw(SP) Sampling period QUALPRD = 0 1tc(SYSCLK) cycles QUALPRD ≠ 0 2tc(SYSCLK) * QUALPRD cycles tw(IQSW) Input qualifier sampling window tw(SP) * (n(1) – 1) cycles tw(GPI) (2) Pulse duration, GPIO low/high Synchronous mode 2tc(SYSCLK) cycles With input qualifier tw(IQSW) + tw(SP) + 1tc(SYSCLK) cycles (1) "n" represents the number of qualification samples as defined by GPxQSELn register. (2) For tw(GPI), pulse width is measured from VIL to VIL for an active low signal and VIH to VIH for an active high signal.
6.13.8.2.2 Sampling Mode
1 1 1 1 1 1 1 1 1 1 10 0 0 0 0 0 0 0 0 0 SYSCLK (A) GPxQSELn = 1,0 (6 samples) (D) Output From Qualifier QUALPRD = 1 (SYSCLK/2) tw(IQSW) tw(SP) (SYSCLK cycle * 2 * QUALPRD) * 5 (C) Sampling Period determined by GPxCTRL[QUALPRD] (B) A. This glitch will be ignored by the input qualifier. The QUALPRD bit field specifies the qualification sampling period. It can vary from 00 to 0xFF. If QUALPRD = 00, then the sampling period is 1 SYSCLK cycle. For any other value "n", the qualification sampling period in 2n SYSCLK cycles (that is, at every 2n SYSCLK cycles, the GPIO pin will be sampled). B. The qualification period selected through the GPxCTRL register applies to groups of eight GPIO pins. C. The qualification block can take either three or six samples. The GPxQSELn Register selects which sample mode is used. D. In the example shown, for the qualifier to detect the change, the input should be stable for 10 SYSCLK cycles or greater. In other words, the inputs should be stable for (5 × QUALPRD × 2) SYSCLK cycles. This would ensure 5 sampling periods for detection to occur. Because external signals are driven asynchronously, an 13-SYSCLK-wide pulse ensures reliable recognition. Figure 6-24. Sampling Mode www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 111 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.13.8.3 Sampling Window Width for Input Signals
The following section summarizes the sampling window width for input signals for various input qualifier configurations. Sampling frequency denotes how often a signal is sampled with respect to SYSCLK. Sampling frequency = SYSCLK/(2 × QUALPRD), if QUALPRD ≠ 0 Sampling frequency = SYSCLK, if QUALPRD = 0 Sampling period = SYSCLK cycle × 2 × QUALPRD, if QUALPRD ≠ 0 In the previous equations, SYSCLK cycle indicates the time period of SYSCLK. Sampling period = SYSCLK cycle, if QUALPRD = 0 In a given sampling window, either 3 or 6 samples of the input signal are taken to determine the validity of the signal. This is determined by the value written to GPxQSELn register. Case 1: Qualification using 3 samples Sampling window width = (SYSCLK cycle × 2 × QUALPRD) × 2, if QUALPRD ≠ 0 Sampling window width = (SYSCLK cycle) × 2, if QUALPRD = 0 Case 2: Qualification using 6 samples Sampling window width = (SYSCLK cycle × 2 × QUALPRD) × 5, if QUALPRD ≠ 0 Sampling window width = (SYSCLK cycle) × 5, if QUALPRD = 0 GPIOxn SYSCLK tw(GPI) Figure 6-25. General-Purpose Input Timing TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
112 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.13.9 Interrupts
The C28x CPU has fourteen peripheral interrupt lines. Two of them (INT13 and INT14) are connected directly to CPU timers 1 and 2, respectively. The remaining twelve are connected to peripheral interrupt signals through the enhanced Peripheral Interrupt Expansion (ePIE) module. The ePIE multiplexes up to sixteen peripheral interrupts into each CPU interrupt line. It also expands the vector table to allow each interrupt to have its own ISR. This allows the CPU to support a large number of peripherals. An interrupt path is divided into three stages—the peripheral, the ePIE, and the CPU. Each stage has its own enable and flag registers. This system allows the CPU to handle one interrupt while others are pending, implement and prioritize nested interrupts in software, and disable interrupts during certain critical tasks. Figure 6-26 shows the interrupt architecture for this device. INPUTXBAR4 INPUTXBAR5 INPUTXBAR6 INPUTXBAR13 INPUTXBAR14 GPIO0 to GPIOx Input X-BAR WD LPM Logic LPMINT WDINT WAKEINT TIMER0 TINT0 ePIE XINT1 Control XINT2 Control XINT3 Control XINT4 Control XINT5 Control Peripherals See ePIE Table NMI module NMI INT1 to INT12 INT13 INT14 TIMER1 TIMER2 CPU Figure 6-26. Device Interrupt Architecture www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 113 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.13.9.1 External Interrupt (XINT) Electrical Data and Timing
For an explanation of the input qualifier parameters, see the General-Purpose Input Timing Requirements table.
6.13.9.1.1 External Interrupt Timing Requirements
tw(INT) Pulse duration, INT input low/high Synchronous 2tc(SYSCLK) cycles With qualifier tw(IQSW) + tw(SP) + 1tc(SYSCLK) cycles
6.13.9.1.2 External Interrupt Switching Characteristics
over recommended operating conditions (unless otherwise noted) PARAMETER MIN MAX UNIT td(INT) Delay time, INT low/high to interrupt-vector fetch(1) tw(IQSW) + 14tc(SYSCLK) tw(IQSW) + tw(SP) + 14tc(SYSCLK) cycles (1) This assumes that the ISR is in a single-cycle memory.
6.13.9.1.3 External Interrupt Timing
XINT1, XINT2, XINT3, XINT4, XINT5 Address bus (internal) tw(INT) td(INT) Figure 6-27. External Interrupt Timing TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
114 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.13.10 Low-Power Modes
This device has HALT, IDLE and STANDBY as clock-gating low-power modes. Further details, as well as the entry and exit procedure, for all of the low-power modes can be found in the Low-Power Modes section of the TMS320F28P55x Real-Time Microcontrollers Technical Reference Manual.
6.13.10.1 Clock-Gating Low-Power Modes
IDLE and HALT modes on this device are similar to those on other C28x devices. Table 6-11 describes the effect on the system when any of the clock-gating low-power modes are entered. Table 6-11. Effect of Clock-Gating Low-Power Modes on the Device MODULES/ CLOCK DOMAIN IDLE STANDBY HALT SYSCLK Active Gated Gated CPUCLK Gated Gated Gated Clock to modules connected to PERx.SYSCLK Active Gated Gated WDCLK Active Active Gated if CLKSRCCTL1.WDHALTI = 0 PLL Powered Powered Software must power down PLL before entering HALT. INTOSC1 Powered Powered Powered down if CLKSRCCTL1.WDHALTI = 0 INTOSC2 Powered Powered Powered down if CLKSRCCTL1.WDHALTI = 0 Flash(1) Powered Powered Powered XTAL(2) Powered Powered Powered (1) The Flash module is not powered down by hardware in any LPM. It may be powered down using software if required by the application. (2) The XTAL is not powered down by hardware in any LPM. It may be powered down by software setting the XTALCR.OSCOFF bit to 1. This can be done at any time during the application if the XTAL is not required. www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 115 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.13.10.2 Low-Power Mode Wake-up Timing
For an explanation of the input qualifier parameters, see the General-Purpose Input Timing Requirements table.
6.13.10.2.1 IDLE Mode Timing Requirements
tw(WAKE) Pulse duration, external wake-up signal Without input qualifier 2tc(SYSCLK) cycles With input qualifier 2tc(SYSCLK) + tw(IQSW)
6.13.10.2.2 IDLE Mode Switching Characteristics
over recommended operating conditions (unless otherwise noted) PARAMETER TEST CONDITIONS MIN MAX UNIT td(WAKE-IDLE) Delay time, external wake signal to program execution resume(1) From Flash (active state) Without input qualifier 40tc(SYSCLK) cycles With input qualifier 40tc(SYSCLK) + tw(WAKE) cycles From RAM Without input qualifier 25tc(SYSCLK) cycles With input qualifier 25tc(SYSCLK) + tw(WAKE) cycles (1) This is the time taken to begin execution of the instruction that immediately follows the IDLE instruction. Execution of an ISR (triggered by the wake-up signal) involves additional latency.
6.13.10.2.3 IDLE Entry and Exit Timing Diagram
(A) XCLKOUT Address/Data (internal) tw(WAKE) td(WAKE-IDLE) A. WAKE can be any enabled interrupt, WDINT or XRSn. After the IDLE instruction is executed, a delay of five OSCCLK cycles (minimum) is needed before the wake-up signal could be asserted. Figure 6-28. IDLE Entry and Exit Timing Diagram TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
116 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.13.10.2.4 STANDBY Mode Timing Requirements
tw(WAKE-INT) Pulse duration, external wake-up signal QUALSTDBY = 0 | 2tc(OSCCLK) 3tc(OSCCLK) cyclesQUALSTDBY > 0 | (2 + QUALSTDBY)tc(OSCCLK) (1) (2 + QUALSTDBY) * tc(OSCCLK) (1) QUALSTDBY is a 6-bit field in the LPMCR register.
6.13.10.2.5 STANDBY Mode Switching Characteristics
over recommended operating conditions (unless otherwise noted) PARAMETER TEST CONDITIONS MIN MAX UNIT td(IDLE-XCOS) Delay time, IDLE instruction executed to XCLKOUT stop 16tc(INTOSC1) cycles td(WAKE-STBY) Delay time, external wake signal to program execution resume(1) Wakeup from flash (Flash module in active state) 175tc(SYSCLK) + tw(WAKE-INT) cycles td(WAKE-STBY) Wakeup from RAM 3tc(OSC) + 15tc(SYSCLK) + tw(WAKE-INT) cycles (1) This is the time taken to begin execution of the instruction that immediately follows the IDLE instruction. Execution of an ISR (triggered by the wake-up signal) involves additional latency.
6.13.10.2.6 STANDBY Entry and Exit Timing Diagram
(A) Device Status STANDBY Normal ExecutionSTANDBY (G)(B) (C) (D)(E) (F) td(IDLE-XCOS) tw(WAKE-INT) td(WAKE-STBY) A. IDLE instruction is executed to put the device into STANDBY mode. B. The LPM block responds to the STANDBY signal, SYSCLK is held for a maximum 16 INTOSC1 clock cycles before being turned off. This delay enables the CPU pipeline and any other pending operations to flush properly. C. Clock to the peripherals are turned off. However, the PLL and watchdog are not shut down. The device is now in STANDBY mode. After the IDLE instruction is executed, a delay of five OSCCLK cycles (minimum) is needed before the wake-up signal could be asserted. D. The external wake-up signal is driven active. E. The wake-up signal fed to a GPIO pin to wake up the device must meet the minimum pulse width requirement. Furthermore, this signal must be free of glitches. If a noisy signal is fed to a GPIO pin, the wake-up behavior of the device will not be deterministic and the device may not exit low-power mode for subsequent wake-up pulses. F. After a latency period, the STANDBY mode is exited. G. Normal execution resumes. The device will respond to the interrupt (if enabled). Figure 6-29. STANDBY Entry and Exit Timing Diagram www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 117 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.13.10.2.7 HALT Mode Timing Requirements
tw(WAKE-GPIO) Pulse duration, GPIO wake-up signal(1) toscst + 2tc(OSCCLK) cycles tw(WAKE-XRS) Pulse duration, XRS wake-up signal(1) toscst + 8tc(OSCCLK) cycles (1) For applications using X1/X2 for OSCCLK, the user must characterize their specific oscillator start-up time as it is dependent on circuit/layout external to the device. See the Crystal Oscillator (XTAL) section for more information. For applications using INTOSC1 or INTOSC2 for OSCCLK, see the Internal Oscillators section for toscst. Oscillator start-up time does not apply to applications using a single-ended crystal on the X1 pin, as it is powered externally to the device.
6.13.10.2.8 HALT Mode Switching Characteristics
over recommended operating conditions (unless otherwise noted) PARAMETER MIN MAX UNIT td(IDLE-XCOS) Delay time, IDLE instruction executed to XCLKOUT stop 16tc(INTOSC1) cycles td(WAKE-HALT) Delay time, external wake signal end to CPU1 program execution resume cyclesWakeup from Flash - Flash module in active state 75tc(OSCCLK) Wakeup from RAM 75tc(OSCCLK) TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
118 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.13.10.2.9 HALT Entry and Exit Timing Diagram
(A) (C) (D)(E) (F) (B) (G) td(IDLE-XCOS) tw(WAKE-GPIO) td(WAKE-HALT) Oscillator Start-up Time A. IDLE instruction is executed to put the device into HALT mode. B. The LPM block responds to the HALT signal, SYSCLK is held for a maximum 16 INTOSC1 clock cycles before being turned off. This delay enables the CPU pipeline and any other pending operations to flush properly. C. Clocks to the peripherals are turned off and the PLL is shut down. If a quartz crystal or ceramic resonator is used as the clock source, the internal oscillator is shut down as well. The device is now in HALT mode and consumes very little power. It is possible to keep the internal oscillators (INTOSC1 and INTOSC2) and the watchdog alive in HALT MODE. This is done by writing 1 to CLKSRCCTL1.WDHALTI. After the IDLE instruction is executed, a delay of five OSCCLK cycles (minimum) is needed before the wake-up signal could be asserted. D. When the GPIOn pin (used to bring the device out of HALT) is driven low, the oscillator is turned on and the oscillator wake-up sequence is initiated. The GPIO pin should be driven high only after the oscillator has stabilized. This enables the provision of a clean clock signal during the PLL lock sequence. Because the falling edge of the GPIO pin asynchronously begins the wake-up procedure, care should be taken to maintain a low noise environment before entering and during HALT mode. E. The wake-up signal fed to a GPIO pin to wake up the device must meet the minimum pulse width requirement. Furthermore, this signal must be free of glitches. If a noisy signal is fed to a GPIO pin, the wake-up behavior of the device will not be deterministic and the device may not exit low-power mode for subsequent wake-up pulses. F. When CLKIN to the core is enabled, the device will respond to the interrupt (if enabled), after some latency. The HALT mode is now exited. G. Normal operation resumes. H. The user must relock the PLL upon HALT wakeup to ensure a stable PLL lock. Figure 6-30. HALT Entry and Exit Timing Diagram www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 119 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.14 Analog Peripherals
The analog subsystem module is described in this section. The analog modules on this device include the Analog-to-Digital Converter (ADC), temperature sensor, Comparator Subsystem (CMPSS), Programmable Gain Amplifier (PGA), and buffered Digital-to-Analog Converter (DAC). The analog subsystem has the following features:
- Flexible voltage references – The ADCs are referenced to VREFHIx and VSSA pins
- VREFHIx pin voltage can be driven in externally or can be generated by an internal bandgap voltage reference
- The internal voltage reference range can be selected to be 0 V to 3.3 V or 0 V to 2.5 V – The buffered DACs are referenced to VREFHIx and VSSA – The comparator DACs are referenced to VDDA and VSSA
- Flexible pin usage – Buffered DAC outputs, comparator subsystem inputs, and digital inputs (AIOs)/outputs (AGPIOs) are multiplexed with ADC inputs – Internal connection to VREFLO on all ADCs for offset self-calibration
6.14.1 Block Diagram
The following analog subsystem block diagrams show the connections between the different integrated analog modules to the device pins. These pins fall into two categories: analog module inputs/outputs and reference pins. The reference pins, VREFHI and VREFLO, can be used to supply an external voltage reference to the associated ADCs. VREFHI can also be used to supply the voltage reference to buffered DAC. The choice of reference is configurable per module for each CMPSS or buffered DAC; the selection is made using the module's configuration registers. Some analog pins support digital functionality through muxed AIOs and AGPIOs. AIOs only support digital input functionality, while AGPIOs support full digital input and output functionality. The following notes apply to all packages:
- Not all analog pins are available on all devices. See the device data manual to determine which pins are available.
- See the device data manual to determine the allowable voltage range for VREFHI and VREFLO.
- An external capacitor is required on the VREFHI pins. See the device data manual for the specific value required. Figure 6-31 shows the Analog Subsystem Block Diagram for the 128-/80-pin TQFP, the 64-pin LQFP, and the 56-pin VQFN. Figure 6-32 shows the Analog Subsystem Block Diagram for the 100-pin LQFP. Figure 6-33 shows the general overview of the analog group connections. The analog pins and internal connections are given in Analog Pins and Internal Connections . Analog Signal Descriptions lists descriptions of analog signals. TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
120 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
A2/B6/C9/PGA1_INP A11/B10/C0/PGA2_OUT VREFHI REFHI CMP2_HP CTRIP2L CTRIPOUT2L Comparator Subsystem 2 VDDA Digital Filter Digital Filter DAC12 DAC12 REFLO CMP2_HN CMP2_LN CMP2_LP CTRIP2H CTRIPOUT2H CMP1_HP CTRIP1L CTRIPOUT1L Comparator Subsystem 1 VDDA Digital Filter Digital Filter DAC12 DAC12 CMP1_HN CMP1_LN CMP1_LP CTRIP1H CTRIPOUT1H CMP4_HP CTRIP4L CTRIPOUT4L Comparator Subsystem 4 VDDA Digital Filter Digital Filter DAC12 DAC12 CMP4_HN CMP4_LN CMP4_LP CTRIP4H CTRIPOUT4H CMP3_HP CTRIP3L CTRIPOUT3L Comparator Subsystem 3 VDDA Digital Filter Digital Filter DAC12 DAC12 CMP3_HN CMP3_LN CMP3_LP CTRIP3H CTRIPOUT3H ADC Inputs C0 to C30 Input MUX VREFLO ADC-C 12-bits REFHI REFLO Input MUX Misc. Analog ADC Inputs A0 to A30 CMPSS Inputs A12 A8/B0/C11 B3/PGA2_INP A14/B14/C4/PGA1_OUT Temp Sensor (C12) Analog Interconnect A7/C3/D12/B30/E30 A1/B7/D11/DACB_OUT A10/B1/C10 B12/C2/PGA2_INM A0/B15/C15/DACA_OUT HPMXSEL4/ /LPMXSEL4/ HPMXSEL2/ /LPMXSEL2/ HPMXSEL0/ /LPMXSEL0/ HPMXSEL1/HNMXSEL1/LPMXSEL1/LNMXSEL1 CMPSS2 Input MUX CMPSS3 Input MUX CMPSS4 Input MUX CMPSS1 Input MUX HPMXSEL2/HNMXSEL0/LPMXSEL2/LNMXSEL0 HPMXSEL1/ /LPMXSEL1/ HPMXSEL0/HNMXSEL1/LPMXSEL0/LNMXSEL1 HPMXSEL0/ /LPMXSEL0/ HPMXSEL3/HNMXSEL0/LPMXSEL3/LNMXSEL0 HPMXSEL4/ /LPMXSEL 4/ HPMXSEL1/HNMXSEL1/LPMXSEL1/LNMXSEL1 HPMXSEL2/ /LPMXSEL 2/ HPMXSEL1/HNMXSEL1/LPMXSEL1/LNMXSEL1 HPMXSEL0/ /LPMXSEL 0/ HPMXSEL3/HNMXSEL0/LPMXSEL3/LNMXSEL0 HPMXSEL2/ /LPMXSEL 2/ HPMXSEL4/ /LPMXSEL 4/ ADC-B 12-bits REFHI REFLO Input MUXADC Inputs B0 to B30 12-bit Buffered DAC-A VREFHI DACA_OUT HPMXSEL5/ /LPMXSEL5/ HPMXSEL4/ /LPMXSEL4/ (128-pin) B5/D15/E15 HPMXSEL5/ /LPMXSEL5/ HPMXSEL5/ /LPMXSEL 5/ (128-pin) B11/D16/E16 B4/C8 C14 C1/E11/PGA3_INP AIOAIOAIO AGPIOAGPIOAGPIO AIOAIOAIO AIOAIOAIO AIOAIOAIO AGPIOAGPIOAGPIO ADC-D 12-bits REFHI REFLO Input MUX ADC-E 12-bits REFHI REFLO Input MUX ADC Inputs D0 to D30 ADC Inputs E0 to E30 AGPIOAGPIOAGPIO AGPIOAGPIOAGPIO A15 HPMXSEL3/HNMXSEL0 /LPMXSEL3/LNMXSEL0 CMPSS Module ADC Module Buffered DAC Module CMPSS Input MUX Temp Sensor Analog Interconnect Reference Circuit ANAREFSEL REFLO Vref Figure 6-31. Analog Subsystem Block Diagram (128-/80-/64-/56-Pin Packages) www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 121 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
A2/B6/C9/PGA1_INP A11/B10/C0/PGA2_OUT VREFHI REFHI CMP2_HP CTRIP2L CTRIPOUT2L Comparator Subsystem 2 VDDA Digital Filter Digital Filter DAC12 DAC12 REFLO CMP2_HN CMP2_LN CMP2_LP CTRIP2H CTRIPOUT2H CMP1_HP CTRIP1L CTRIPOUT1L Comparator Subsystem 1 VDDA Digital Filter Digital Filter DAC12 DAC12 CMP1_HN CMP1_LN CMP1_LP CTRIP1H CTRIPOUT1H CMP4_HP CTRIP4L CTRIPOUT4L Comparator Subsystem 4 VDDA Digital Filter Digital Filter DAC12 DAC12 CMP4_HN CMP4_LN CMP4_LP CTRIP4H CTRIPOUT4H CMP3_HP CTRIP3L CTRIPOUT3L Comparator Subsystem 3 VDDA Digital Filter Digital Filter DAC12 DAC12 CMP3_HN CMP3_LN CMP3_LP CTRIP3H CTRIPOUT3H Reference Circuit ANAREFSEL REFLO Vref ADC Inputs C0 to C30 Input MUX VREFLO ADC-C 12-bits REFHI REFLO Input MUX Misc. Analog ADC Inputs A0 to A30 CMPSS Inputs B0/C11 A12 A8/B0/C11 B3/PGA2_INP A14/B14/C4/PGA1_OUT Temp Sensor (C12) Analog Interconnect A7/B30/C3/D12/E30 A6/D14/E14 B2/C6/E12 A1/B7/D11/DACB_OUT A10/B1/C10 B12/C2/PGA2_INM A0/B15/C15/DACA_OUT HPMXSEL4/ /LPMXSEL4/ HPMXSEL2/ /LPMXSEL2/ HPMXSEL0/ /LPMXSEL0/ HPMXSEL1/HNMXSEL1/LPMXSEL1/LNMXSEL1 CMPSS2 Input MUX CMPSS3 Input MUX CMPSS4 Input MUX CMPSS1 Input MUX HPMXSEL2/HNMXSEL0/LPMXSEL2/LNMXSEL0 HPMXSEL1/ /LPMXSEL1/ HPMXSEL3/ /LPMXSEL3/ HPMXSEL0/HNMXSEL1/LPMXSEL0/LNMXSEL1 HPMXSEL0/ /LPMXSEL0/ HPMXSEL3/HNMXSEL0/LPMXSEL3/LNMXSEL0 HPMXSEL4/ /LPMXSEL 4/ HPMXSEL1/HNMXSEL1/LPMXSEL1/LNMXSEL1 HPMXSEL2/ /LPMXSEL 2/ HPMXSEL1/HNMXSEL1/LPMXSEL1/LNMXSEL1 HPMXSEL0/ /LPMXSEL 0/ HPMXSEL3/HNMXSEL0/LPMXSEL3/LNMXSEL0 HPMXSEL2/ /LPMXSEL 2/ HPMXSEL4/ /LPMXSEL 4/ ADC-B 12-bits REFHI REFLO Input MUXADC Inputs B0 to B30 12-bit Buffered DAC-A VREFHI DACA_OUT HPMXSEL5/ /LPMXSEL5/ HPMXSEL5/ /LPMXSEL5/ B5/D15/E15 HPMXSEL5/ /LPMXSEL5/ HPMXSEL5/ /LPMXSEL 5/B11/D16/E16 B4/C8 C14 C1/E11/PGA3_INP AIOAIOAIO AGPIOAGPIOAGPIO AIOAIOAIO AIOAIOAIO AIOAIOAIO AGPIOAGPIOAGPIO ADC-D 12-bits REFHI REFLO Input MUX ADC-E 12-bits REFHI REFLO Input MUX ADC Inputs D0 to D30 ADC Inputs E0 to E30 AGPIOAGPIOAGPIO AGPIOAGPIOAGPIO CMPSS Module ADC Module Buffered DAC Module CMPSS Input MUX Temp Sensor Analog Interconnect Reference Circuit Figure 6-32. Analog Subsystem Block Diagram (100-Pin Package) TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
122 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
CMPx_HP0 CMPx_HP1 CMPx_HP2 CMPx_HP3 CMPx_HP4 CMPx_HN0 CMPx_HN1 CMPx_LN0 CMPx_LN1 CMPx_LP0 CMPx_LP1 CMPx_LP2 CMPx_LP3 CMPx_LP4 CMPxHPMX CMPxHNMX CMPxLNMX CMPxLPMX CMPx_HP CMPx_HN CMPx_LN CMPx_LP To CMPSSx ADCA ADCC ADCA ADCC To ADCs AIO AIO ADCB ADCB AIO CMPx_HP5 5 CMPx_LP5 AGPIO AGPIO ADCD ADCD AIO AGPIO ADCE PGAx_OUT AIO AGPIO AGPIO TO Device Pins PGAx_INP PGAx_INM ADCE VSSA VDDA PGAx_OUT_INT PGAx_OUT 6CMPx_HP6 CMPx_LP6 PGA Module CMPSS Input MUX AIO AGPIO Figure 6-33. Analog Group Connections www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 123 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Input connections to the CMPSS modules are selectable through a programmable input mux. Figure 6-33 demonstrates the connection between the input MUX of CMPSS modules, PGA modules, and ADC modules. Table 6-12 shows the mapping of ADC input signals and PGA input and output signals to CMPSS mux inputs.
- To configure the CMPx_HP input mux for CMPSSx, write to the CMPxHPMXSEL field in the CMPHPMXSEL analog subsystem register.
- To configure the CMPx_HN input mux for CMPSSx, write to the CMPxHNMXSEL field in the CMPHNMXSEL analog subsystem register.
- To configure the CMPx_LP input mux for CMPSSx, write to the CMPxLPMXSEL field in the CMPLPMXSEL analog subsystem register.
- To configure the CMPx_LN input mux for CMPSSx, write to the CMPxLNMXSEL field in the CMPLNMXSEL analog subsystem register. Table 6-12. CMPSS Input Mux Options CMPSSx Input MUX CMP1 CMP2 CMP3 CMP4 HP0 A2, B6, C9, PGA1_INP A4, B8 B2,C6, E12 B4, C8 HP1 A11, B10, C0, PGA2_OUT A12 B12, C2, PGA2_INM A7, C3, D12, B30, E30, HP2 A6, D14, E14(3) A9 A0, B15, C15, DACA_OUT C1, E11, PGA3_INP HP3 A15(2) A10, B1, C10 B3, PGA2_INP C14 B0, C11(1) HP4 A1, B7, D11, DACB_OUT A14, B14, C4, PGA1_OUT B0, C11(2) HP5 B5, D15, E15(4) A5(1) A3 B11, D16, E16(4) HP6 PGA1_OUT_INT PGA3_OUT_INT PGA2_OUT_INT HP7 TEMP SENSOR HN0 A15(2) A10, B1, C10 B3, PGA2_INP C14 HN1 A11, B10, C0, PGA2_OUT A12 B12, C2, PGA2_INM A7, B30, C3, D12, E30 LP0 A2, B6, C9, PGA1_INP A4, B8 B2, C6, E12 B4, C8 LP1 A11, B10, C0, PGA2_OUT A12 B12, C2, PGA2_INM A7, B30, C3, D12, E30 LP2 A6, D14, E14(3) A9 A0, B15, C15, DACA_OUT C1, E11, PGA3_INP LP3 A15(2) A10, B1, C10 B3, PGA2_INP C14 B0, C11(1) LP4 A1, B7, D11, DACB_OUT A14, B14, C4, PGA1_OUT B0, C11(2) LP5 B5, D15, E15(4) A5(1) A3 B11, D16, E16(4) LP6 PGA1_OUT_INT PGA3_OUT_INT PGA2_OUT_INT LN0 A15 A10, B1, C10 B3, PGA2_INP C14 LN1 A11, B10, C0, PGA2_OUT A12 B12, C2, PGA2_INM A7, C3, D12, B30,E30 (1) These MUX options are available only on 100 QFP package. (2) This MUX option is available only on 56 QFN, 64 QFP, 80 QFP, and 128 QFP packages. (3) This MUX option is available only on 64 QFP, 80 QFP, 100 QFP, and 128 QFP packages. (4) This MUX option is available only on 100 QFP and 128 QFP packages. TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
124 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.14.2 Analog Pins and Internal Connections
Table 6-13. Analog Pins and Internal Connections Pin Name Pins/Package ADC DAC PGA Comparator Subsystem (MUX) AIO Input/ AGPIO128 QFP 100 QFP QFP QFP QFN A B C D E High Positive High Negative Low Positive Low Negative VREFHI 31 25 20 16 14 - - - D20 E20 VREFLO 33 27 21 17 15 A13 B13 C13 D13 E13 Analog Group 1 CMP1 A6/D14/E14 18 14 10 6 - A6 - - D14 E14 CMP1 (HPMXSEL=2) - CMP1 (LPMXSEL=2) - AGPIO228 (3) A2/B6/C9/PGA1_INP 21 17 13 9 7 A2 B6 C9 - - PGA1_INP CMP1 (HPMXSEL=0) - CMP1 (LPMXSEL=0) - AGPIO224 (3) A15 14 10 8 A15 - - - - CMP1 (HPMXSEL=3) CMP1 (HNMXSEL=0) CMP1 (LPMXSEL=3) CMP1 (LNMXSEL=0) AGPIO233 (3) B9/C7/PGA1_INM 18 - B9 C7 PGA1_INM A11/B10/C0/PGA2_OUT 27 20 16 12 10 A11 B10 C0 - - PGA2_OUT CMP1 (HPMXSEL=1) CMP1 (HNMXSEL=1) CMP1 (LPMXSEL=1) CMP1 (LNMXSEL=1) AIO237 A1/B7/D11/DACB_OUT 29 22 18 14 12 A1 B7 - D11 - DACB_OUT CMP1 (HPMXSEL=4) - CMP1 (LPMXSEL=4) - AIO232 B5/D15/E15 38 32 - - - - B5 D15 E15 - CMP1 (HPMXSEL=5) - CMP1 (LPMXSEL=5) - AIO252 PGA3_OUT 24 20 18 - - - PGA3_OUT Analog Group 2 CMP2 A4/B8 42 36 27 23 21 A4 B8 - - - CMP2 (HPMXSEL=0) - CMP2 (LPMXSEL=0) - AIO225 A12 35 28 22 18 16 A12 - - - - CMP2 (HPMXSEL=1) - CMP2 (LPMXSEL=1) - AIO238 A9 48 38 28 24 22 A9 - - - - CMP2 (HPMXSEL=2) - CMP2 (LPMXSEL=2) - AGPIO227 (3) A10/B1/C10 50 40 29 25 23 A10 B1 C10 - - CMP2 (HPMXSEL=3) CMP2 (HNMXSEL=0) CMP2 (LPMXSEL=3) CMP2 (LNMXSEL=0) AGPIO230 (3) B0/C11 - 41 - - - - B0 C11 CMP2 (HPMXSEL=3) - CMP2 (LPMXSEL=3) - AGPIO231 (3) 28 - 17 13 11 A5 - - - - CMP2 (HPMXSEL=5) - CMP2 (LPMXSEL=5) - AIO249 - 35 - - - Analog Group 3 CMP3 B2/C6/E12 19 15 11 7 - - B2 C6 - E12 CMP3 (HPMXSEL=0) - CMP3 (LPMXSEL=0) - AGPIO226 (3) B12/C2/PGA2_INM 28 21 17 13 11 - B12 C2 - - PGA2_INM CMP3 (HPMXSEL=1) CMP3 (HNMXSEL=1) CMP3 (LPMXSEL=1) CMP3 (LNMXSEL=1) AIO244 www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 125 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 6-13. Analog Pins and Internal Connections (continued) Pin Name Pins/Package ADC DAC PGA Comparator Subsystem (MUX) AIO Input/ AGPIO128 QFP 100 QFP QFP QFP QFN A B C D E High Positive High Negative Low Positive Low Negative A0/B15/C15/DACA_OUT 30 23 19 15 13 A0 B15 C15 - - DACA_OUT CMP3 (HPMXSEL=2) - CMP3 (LPMXSEL=2) - AIO231 B3/PGA2_INP 12 8 6 - B3 - - - PGA2_INP CMP3 (HPMXSEL=3) CMP3 (HNMXSEL=0) CMP3 (LPMXSEL=3) CMP3 (LNMXSEL=0) AGPIO242 (3) C5 28 - C5 A14/B14/C4/PGA1_OUT 26 19 15 11 9 A14 B14 C4 - - PGA1_OUT CMP3 (HPMXSEL=4) - CMP3 (LPMXSEL=4) - AIO239 20 - 12 8 6 A3 - - - - CMP3 (HPMXSEL=5) - CMP3 (LPMXSEL=5) - - 18 - - - AIO229 Analog Group 4 CMP4 B4/C8 49 39 28 24 22 - B4 C8 - - CMP4 (HPMXSEL=0) - CMP4 (LPMXSEL=0) - AGPIO236 (3) C1/E11/PGA3_INP 35 29 22 18 16 - - C1 - E11 PGA3_INP CMP4 (HPMXSEL=2) - CMP4 (LPMXSEL=2) - - C14 42 42 27 23 21 - - C14 - - CMP4 (HPMXSEL=3) CMP4 (HNMXSEL=0) CMP4 (LPMXSEL=3) CMP4 (LNMXSEL=0) AGPIO247 (3) B0/C11 39 - 24 20 18 - B0 C11 - - CMP4 (HPMXSEL=4) - CMP4 (LPMXSEL=4) - AIO241 A8 - -- 37 - - - A8 AIO240 B11/D16/E16 36 30 - - - - B11 - D16 E16 CMP4 (HPMXSEL=5) - CMP4 (LPMXSEL=5) - AIO251 PGA3_INM 36(1) 30(1) 23 19 17 - - - - - PGA3_INM A7/B30/C3/D12/E30 37 31 A7 B30 C3 D12 E30 CMP4 (HPMXSEL=1) CMP4 (HNMXSEL=1) CMP4 (LPMXSEL=1) CMP4 (LNMXSEL=1) AIO245 Other Analog TempSensor(2) - - C12 - - CMP2 (HPMXSEL=7) - - - - PGA1_OUT_INT(2) A21 B21 - - - PGA1_OUT_I NT CMP1 (HPMXSEL=6) - CMP1 (LPMXSEL=6) - - PGA2_OUT_INT(2) - B22 C21 - - PGA2_OUT_I NT CMP3 (HPMXSEL=6) - CMP3 (LPMXSEL=6) - - PGA3_OUT_INT(2) A22 - C22 - - PGA3_OUT_I NT CMP2 (HPMXSEL=6) - CMP2 (LPMXSEL=6) - - (1) Signal is bonded together with another signal as a single pin on this package. (2) Internal connection only; does not come to a device pin. (3) Only on 100 QFP package, AGPIO 247 is available. TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
126 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
The GPIOs on the analog pins support full digital input and output functionality and are referred to as AGPIOs. By default, the AGPIOs are unconnected; that is, the analog and digital functions are both disabled. For configuration details, see the Digital Inputs and Outputs on ADC Pins (AGPIOs) section. www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 127 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.14.3 Analog Signal Descriptions
Table 6-14. Analog Signal Descriptions Signal Name Description AIOx Digital input on ADC pin AGPIOx Digital input/output pin with ADC functionality ADCINAx, Ax ADC A Input ADCINBx, Bx ADC B Input ADCINCx, Cx ADC C Input ADCINDx, Dx ADC D Input ADCINEx, Ex ADC E Input CMPx_HP Comparator subsystem high comparator positive input CMPx_HN Comparator subsystem high comparator negative input CMPx_LP Comparator subsystem low comparator positive input CMPx_LN Comparator subsystem low comparator negative input DACA_OUT Buffered DAC Output DACB_OUT CMPSS1 DAC Output PGAx_INP PGA module non-inverting pin PGAx_INM PGA module inverting pin PGAx_OUT PGA module output PGAx_OUT_INT PGA module internal output connected to CMPSS and ADC modules TEMP SENSOR, TS Internal temperature sensor TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
128 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.14.4 Analog-to-Digital Converter (ADC)
The ADC module described here is a successive approximation (SAR) style ADC with resolution of 12 bits . This section refers to the analog circuits of the converter as the “core,” and includes the channel-select MUX, the sample-and-hold (S/H) circuit, the successive approximation circuits, voltage reference circuits, and other analog support circuits. The digital circuits of the converter are referred to as the “wrapper” and include logic for programmable conversions, result registers, interfaces to analog circuits, interfaces to the peripheral buses, post-processing circuits, and interfaces to other on-chip modules. Each ADC module consists of a single sample-and-hold (S/H) circuit. The ADC module is designed to be duplicated multiple times on the same chip, allowing simultaneous sampling or independent operation of multiple ADCs. The ADC wrapper is start-of-conversion (SOC)-based (see the SOC Principle of Operation section of the Analog-to-Digital Converter (ADC) chapter in the TMS320F28P55x Real-Time Microcontrollers Technical Reference Manual). Each ADC has the following features:
- Resolution of 12 bits
- Ratiometric external reference set by VREFHI/VREFLO
- Selectable internal reference of 2.5 V or 3.3 V
- Single-ended signal mode
- Input multiplexer with up to 32 channels
- 16 configurable SOCs
- 16 individually addressable result registers
- External analog input mux selection per SOC, up to 4 bits
- Sample cap reset feature for memory crosstalk mitigation
- Multiple trigger sources – Software immediate start – All ePWMs: ADCSOC A or B – GPIO XINT2 – CPU Timers 0/1/2 – ADCINT1/2 – ECAP events in capture mode (CEVT1, CEVT2, CEVT3, and CEVT4) and APWM mode (period match, compare match, or both). – Global software trigger for multiple ADCs
- Four flexible PIE interrupts
- Burst-mode triggering option
- Hardware oversampling mode up to 128x, with configurable trigger spread delay
- Hardware undersampling mode
- Trigger phase delay function
- Four post-processing blocks, each with: – Saturating offset calibration – Error from setpoint calculation – High, low, and zero-crossing compare, with interrupt and ePWM trip capability – Configurable digital filter for high/low/zero-crossing compare – Trigger-to-sample delay capture – Absolute value calculation – 24-bit accumulation register for oversampling, with configurable binary shift – Minimum/maximum calculation for outlier rejection Note Not every channel can be pinned out from all ADCs. See the Pin Configuration and Functions section to determine which channels are available. www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 129 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
The block diagram for the ADC core and ADC wrapper are shown in Figure 6-34. Analog System Control Analog to Digital Control Logic Analog to Digital Core Input Circuit Reference Voltage Generator SOC Arbitration& Control SOCx (0-15) ADCIN0 Converter ADCIN1 ADCIN2 ADCIN3 ADCIN4 ADCIN5 ADCIN6 ADCIN7 Bandgap Reference Circuit Interrupt Block (1-4) Triggers ADCIN8 ADCIN9 ADCIN10 ADCIN11 VREFLO VREFHI CHSEL ADCSOC [15:0] ADCINT1-4_DMA REFPMUXSEL 29ADCIN29 ADCIN30 ADCIN31 TRIGSELACQPS CHSEL RESOLUTION SIGNALMODE Post Processing Block (1-4) [15:0] SIGNALMODE RESOLUTION RESULT ADCRESULT 0–15 Regs Limit Compare and Event Logic, Digital Filters ADCEVTINT [15:0] ADCEVT TRIGGER[15:0] FREECOUNT EOCx[15:0] DOUT VIN- VIN+ S/H Circuit ANAREFx1P65SEL REPEATx (1-2) TRIGSEL MODE NSEL PHASE Conversion Start Delay Calculation Sample Correction (OFFCAL, OFFREF, INV, ABS, last-sample delta) Oversampling and Accumulation (COUNT, SUM, MAX, MIN) PPBxRESULT ADCOSINT1 Sync Logic EOCx[15:0] SOCxSTART[15:0] ADCEXTMUX[3:0] [15:0] SPREAD ADCINT1-4 Clock Prescaler SYSCLKADCCLK EXTCHSEL Analog to Digital Control Logic Post Processing Block Analog to Digital Core Reference Voltage Generator Analog System Control Input Circuit Converter REPEATx (1-2) SOCx (0-15) Figure 6-34. ADC Module Block Diagram TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
130 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.14.4.1 ADC Configurability
Some ADC configurations are individually controlled by the SOCs, while others are globally controlled per ADC module. Table 6-15 summarizes the basic ADC options and their level of configurability. Table 6-15. ADC Options and Configuration Levels OPTIONS CONFIGURABILITY Clock Per module(1) Resolution Not configurable (12-bit resolution only) Signal mode Not configurable (single-ended signal mode only) Reference voltage source Either external or internal for all modules Trigger source Per SOC(1) Converted channel Per SOC Acquisition window duration Per SOC(1) EOC location Per module Burst mode Per module(1) (1) Writing these values differently to different ADC modules could cause the ADCs to operate asynchronously. For guidance on when the ADCs are operating synchronously or asynchronously, see the Ensuring Synchronous Operation section of the Analog-to-Digital Converter (ADC) chapter in the TMS320F28P55x Real-Time Microcontrollers Technical Reference Manual.
6.14.4.1.1 Signal Mode
The ADC supports single-ended signaling. The input voltage to the converter is sampled through a single pin (ADCINx), referenced to VREFLO. VREFHI VREFLO (VSSA) VREFHI/2 Pin Voltage ADCINx ADC ADCINx VREFLO VREFHI 2n - 1 Digital Output ADC Vin Figure 6-35. Single-ended Signaling Mode www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 131 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.14.4.2 ADC Electrical Data and Timing
The ADC inputs should be kept below VDDA + 0.3 V. If an ADC input goes above this level, ADC disturbances to other channels may occur by two mechanisms:
- ADC input overvoltage will overdrive the CMPSS mux, disturbing all other channels which share a common CMPSS mux. This disturbance will be continuous regardless of if the overvoltage input is sampled by the ADC
- When the ADC samples the overvoltage ADC input, VREFHI will be pulled up to a higher level. This will disturb subsequent ADC conversions on any channel until the VREF stabilizes Note The VREFHI pin must be kept below VDDA + 0.3 V to ensure proper functional operation. If the VREFHI pin exceeds this level, a blocking circuit may activate, and the internal value of VREFHI may float to 0 V internally, giving improper ADC conversion.
6.14.4.2.1 ADC Operating Conditions
over recommended operating conditions (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT ADCCLK (derived from PERx.SYSCLK) 5 75 MHz Sample rate 150-MHz SYSCLK
3.9 MSPS
Sample window duration (set by ACQPS and PERx.SYSCLK)(1) With 50 Ω or less Rs 67 ns VREFHI External Reference 1.55 1.65 or 2.50 VDDA V VREFHI(2) Internal Reference = 3.3V Range 1.65 V Internal Reference = 2.5V Range 2.50 V VREFLO VSSA VSSA V VREFHI - VREFLO 2.4 VDDA V Conversion range Internal Reference = 3.3 V Range 0 3.3 V Conversion range Internal Reference = 2.5 V Range 0 2.5 V Conversion range External Reference VREFLO VREFHI V Conversion range Analog Supply as Reference VSSA VDDA V (1) The sample window must also be at least as long as 1 ADCCLK cycle for correct ADC operation. (2) In internal reference mode, the reference voltage is driven out of the VREFHI pin by the device. The user should not drive a voltage into the pin in this mode.
6.14.4.2.2 ADC Characteristics
over recommended operating conditions (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT General ADCCLK Conversion Cycles 150-MHz SYSCLK 14 ADCCLKs Power Up Time External Reference mode 500 µs Internal Reference mode 5000 µs Internal Reference mode, when switching between 2.5-V range and 3.3-V range. 5000 µs VREFHI input current(1) 40 µA Internal Reference Capacitor Value(2) 2.2 µF TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
132 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.14.4.2.2 ADC Characteristics (continued)
over recommended operating conditions (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT External Reference Capacitor Value(2) 2.2 µF DC Characteristics Gain Error Internal reference –45 45 LSB External reference –5 ±3 5 Offset Error –5 ±1 5 LSB Channel-to-Channel Gain Error(4) 2 LSB Channel-to-Channel Offset Error(4) 2 LSB ADC-to-ADC Gain Error(5) Identical VREFHI and VREFLO for all ADCs 4 LSB ADC-to-ADC Offset Error(5) Identical VREFHI and VREFLO for all ADCs 2 LSB DNL Error >–1 ±0.5 1 LSB INL Error –2 ±1.5 2 LSB ADC-to-ADC Isolation VREFHI = 2.5 V, synchronous ADCs –1 1 LSBs AC Characteristics SNR(3) VREFHI = 2.5 V, fin = 100 kHz, SYSCLK from X1 69.2 dBVREFHI = 2.5 V, fin = 100 kHz, SYSCLK from INTOSC TBD THD(3) VREFHI = 2.5 V, fin = 100 kHz –83 dB SFDR(3) VREFHI = 2.5 V, fin = 100 kHz 79.2 dB SINAD(3) VREFHI = 2.5 V, fin = 100 kHz, SYSCLK from X1 68.5 dBVREFHI = 2.5 V, fin = 100 kHz, SYSCLK from INTOSC 60.0 ENOB(3) VREFHI = 2.5 V, fin = 100 kHz, SYSCLK from X1, Single ADC 11.2 bitsVREFHI = 2.5 V, fin = 100 kHz, SYSCLK from X1, synchronous ADCs TBD VREFHI = 2.5 V, fin = 100 kHz, SYSCLK from X1, asynchronous ADCs Not Supported PSRR VDD = 1.2-V DC + 100mV DC up to Sine at 1 kHz 60 dB VDD = 1.2-V DC + 100 mV DC up to Sine at 300 kHz 57 VDDA = 3.3-V DC + 200 mV DC up to Sine at 1 kHz 60 VDDA = 3.3-V DC + 200 mV Sine at 900 kHz 57 (1) Load current on VREFHI increases when ADC input is greater than VDDA. This causes inaccurate conversions. (2) A ceramic capacitor with package size of 0805 or smaller is preferred. Up to ±20% tolerance is acceptable. (3) IO activity is minimized on pins adjacent to ADC input and VREFHI pins as part of best practices to reduce capacitive coupling and crosstalk. (4) Variation across all channels belonging to the same ADC module. (5) Worst case variation compared to other ADC modules. www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 133 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.14.4.2.3 ADC INL and DNL
VREFHI – VREFLO Digital Output Code Analog Input Voltage = Ideal Transfer Function = Transfer Function (Low) = INL Error 0x002 0x001 0x000 0x003 0x004 0x005 0x006 DNL Error 2^n R = Figure 6-36. ADC INL and DNL
6.14.4.2.4 ADC Input Model
Table 6-16. Input Model Parameters DESCRIPTION REFERENCE MODE VALUE Cp Parasitic input capacitance All See Table 6-17 to Table 6-21 Ron Sampling switch resistance External Reference, 2.5-V Internal Reference 1000 Ω 3.3-V Internal Reference 1700 Ω Ch Sampling capacitor External Reference, 2.5-V Internal Reference 4 pF 3.3-V Internal Reference 2.5 pF Rs Nominal source impedance All 50 Ω ADC RonSwitch VREFLO ChCp ADCINx AC Rs Figure 6-37. Input Model This input model should be used with actual signal source impedance to determine the acquisition window duration. For more information, see the Choosing an Acquisition Window Duration section of the Analog- TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
134 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
to-Digital Converter (ADC) chapter in the TMS320F28P55x Real-Time Microcontrollers Technical Reference Manual. For recommendations on improving ADC input circuits, see the ADC Input Circuit Evaluation for C2000 MCUs Application Report. Table 6-17. Per-Channel Parasitic Capacitance for 128-Pin QFP ADC CHANNEL Cp (pF) COMPARATOR DISABLED COMPARATOR ENABLED A0, B15, C15, DACA_OUT 1.7 3.2 A1, B7, D11, DACB_OUT, REFHI 1.5 3.0 A2, B6, C9, PGA1_INP 1.7 3.2 A3 5.4 6.9 A4, B8, REFLO 1.2 2.7 A5 2.2 3.7 A6, D14, E14 0.2 1.7 A7, C3, D12, B30, E30 0.9 2.4 A8, B0, C11 0.5 2.0 A9 0.2 1.7 A10, B1, C10 0.2 1.7 A11, B10, C0,PGA2_OUT 1.1 2.6 A12 1.1 2.6 A14, B14, C4, PGA1_OUT 1.0 2.5 A15 0.5 2.0 A16, B16, C16 0.2 0.2 A17,B17,C17 0.2 0.2 A18,B18,C18 0.2 0.2 A19,B19,C19 0.2 0.2 A20,B20,C20 0.2 0.2 B2, C6, E12 0.2 1.7 B3, PGA2_INP 0.2 1.7 B4, C8 0.2 1.7 B5, D15, E15 0.5 2.0 B9, C7, PGA1_INM 1.8 1.8 B11, D16, E16 5.0 6.5 B12, C2, PGA2_INM 1.0 2.5 C1,E11,PGA3_INP 0.7 2.2 C5 5.4 5.4 C14 4.9 6.4 D0,E0,A24 0.2 0.2 D1,E1,B24 0.2 0.2 D2,E2,C24 0.2 0.2 D3,E3,A25 0.2 0.2 D4,E4,B25 0.2 0.2 www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 135 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 6-17. Per-Channel Parasitic Capacitance for 128-Pin QFP (continued) ADC CHANNEL Cp (pF) COMPARATOR DISABLED COMPARATOR ENABLED D5,E5,C25 5.0 5.0 D6,E6,A26 5.0 5.0 D7,E7,B26 5.0 5.0 D8, E8, C26 0.2 0.2 D9,E9, A27 0.2 0.2 D10,E10,B27 0.2 0.2 D18,E18,C27 0.2 0.2 D19,E19,A28 0.2 0.2 Table 6-18. Per-Channel Parasitic Capacitance for 100-Pin QFP ADC CHANNEL Cp (pF) COMPARATOR DISABLED COMPARATOR ENABLED A0, B15, C15, DACA_OUT 1.7 3.2 A1, B7, D11, DACB_OUT, REFHI 1.5 3.0 A2, B6, C9, PGA1_INP 1.7 3.2 A3 5.4 6.9 A4, B8, REFLO 1.2 2.7 A5 2.2 3.7 A6, D14, E14 0.2 1.7 A7, C3, D12, B30, E30 0.9 2.4 A8, B0, C11 0.5 2.0 A9 0.2 1.7 A10, B1, C10 0.2 1.7 A11, B10, C0, PGA2_OUT 1.1 2.6 A12 1.1 2.6 A14, B14, C4, PGA1_OUT 1.0 2.5 A16/B16/C16 0.2 0.2 A17,B17,C17 0.2 0.2 A18,B18,C18 0.2 0.2 A19,B19,C19 0.2 0.2 A20,B20,C20 0.2 0.2 B2, C6, E12 0.2 1.7 B3, PGA2_INP 0.2 1.7 B4, C8 0.2 1.7 B5, D15, E15 0.5 2.0 B9, C7, PGA1_INM 1.8 1.8 B11, D16, E16 5.0 6.5 B12, C2, PGA2_INM 1.0 2.5 C1,E11,PGA3_INP 0.7 2.2 TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
136 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 6-18. Per-Channel Parasitic Capacitance for 100-Pin QFP (continued) ADC CHANNEL Cp (pF) COMPARATOR DISABLED COMPARATOR ENABLED C5 5.4 5.4 C14 4.9 6.4 D0,E0,A24 0.2 0.2 D1,E1,B24 0.2 0.2 D2,E2,C24 0.2 0.2 D3,E3,A25 0.2 0.2 D4,E4,B25 0.2 0.2 Table 6-19. Per-Channel Parasitic Capacitance for 80-Pin QFP ADC CHANNEL Cp (pF) COMPARATOR DISABLED COMPARATOR ENABLED A0, B15, C15, DACA_OUT 1.7 3.2 A1, B7, D11, DACB_OUT, REFHI 1.5 3.0 A2, B6, C9, PGA1_INP 1.7 3.2 A3 5.4 6.9 A4, B8, REFLO 1.2 2.7 A5 2.2 3.7 A6, D14, E14 0.2 1.7 A7, C3, D12, B30,E30 0.9 2.4 A8, B0, C11 0.5 2.0 A9 0.2 1.7 A10, B1, C10 0.2 1.7 A11, B10, C0,PGA2_OUT 1.1 2.6 A12 1.1 2.6 A14, B14, C4, PGA1_OUT 1.0 2.5 A15 0.5 2.0 A16/B16/C16 0.2 0.2 A17,B17,C17 0.2 0.2 A18,B18,C18 0.2 0.2 A19,B19,C19 0.2 0.2 A20,B20,C20 0.2 0.2 B2, C6, E12 0.2 1.7 B3, PGA2_INP 0.2 1.7 B4, C8 0.2 1.7 B9, C7, PGA1_INM 1.8 1.8 B12, C2, PGA2_INM 1.0 2.5 C1,E11,PGA3_INP 0.7 2.2 C5 5.4 5.4 C14 4.9 6.4 www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 137 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 6-19. Per-Channel Parasitic Capacitance for 80-Pin QFP (continued) ADC CHANNEL Cp (pF) COMPARATOR DISABLED COMPARATOR ENABLED D0,E0,A24 0.2 0.2 D1,E1,B24 0.2 0.2 D2,E2,C24 0.2 0.2 D3,E3,A25 0.2 0.2 D4,E4,B25 0.2 0.2 Table 6-20. Per-Channel Parasitic Capacitance for 64-Pin QFP ADC CHANNEL Cp (pF) COMPARATOR DISABLED COMPARATOR ENABLED A0, B15, C15, DACA_OUT 1.7 3.2 A1, B7, D11, DACB_OUT, REFHI 1.5 3.0 A2, B6, C9, PGA1_INP 1.7 3.2 A3 5.4 6.9 A4, B8, REFLO 1.2 2.7 A5 2.2 3.7 A6, D14, E14 0.2 1.7 A7, C3, D12, B30, E30 0.9 2.4 A8, B0, C11 0.5 2.0 A9 0.2 1.7 A10, B1, C10 0.2 1.7 A11, B10, C0,PGA2_OUT 1.1 2.6 A12 1.1 2.6 A14, B14, C4, PGA1_OUT 1.0 2.5 A15 0.5 2.0 A16, B16, C16 0.2 0.2 A17,B17,C17 0.2 0.2 A18,B18,C18 0.2 0.2 A19,B19,C19 0.2 0.2 A20,B20,C20 0.2 0.2 B2, C6, E12 0.2 1.7 B3, PGA2_INP 0.2 1.7 B4, C8 0.2 1.7 B9, C7, PGA1_INM 1.8 1.8 B12, C2, PGA2_INM 1.0 2.5 C1,E11,PGA3_INP 0.7 2.2 C5 5.4 5.4 C14 4.9 6.4 D0,E0,A24 0.2 0.2 D1,E1,B24 0.2 0.2 TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
138 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 6-20. Per-Channel Parasitic Capacitance for 64-Pin QFP (continued) ADC CHANNEL Cp (pF) COMPARATOR DISABLED COMPARATOR ENABLED D2,E2,C24 0.2 0.2 D3,E3,A25 0.2 0.2 D4,E4,B25 0.2 0.2 Table 6-21. Per-Channel Parasitic Capacitance for 56-Pin QFN ADC CHANNEL Cp (pF) COMPARATOR DISABLED COMPARATOR ENABLED A0, B15, C15, DACA_OUT 1.7 3.2 A1, B7, D11, DACB_OUT, REFHI 1.5 3.0 A2, B6, C9, PGA1_INP 1.7 3.2 A3 5.4 6.9 A4, B8, REFLO 1.2 2.7 A5 2.2 3.7 A7, C3, D12, B30,E30 0.9 2.4 A8, B0, C11 0.5 2.0 A9 0.2 1.7 A10, B1, C10 0.2 1.7 A11, B10, C0,PGA2_OUT 1.1 2.6 A12 1.1 2.6 A14, B14, C4, PGA1_OUT 1.0 2.5 A15 0.5 2.0 A16,B16,C16 0.2 0.2 A17,B17,C17 0.2 0.2 A18,B18,C18 0.2 0.2 A19,B19,C19 0.2 0.2 A20,B20,C20 0.2 0.2 B3, PGA2_INP 0.2 1.7 B4, C8 0.2 1.7 B9, C7, PGA1_INM 1.8 1.8 B12, C2, PGA2_INM 1.0 2.5 C1,E11,PGA3_INP 0.7 2.2 C5 5.4 5.4 C14 4.9 6.4 D0,E0,A24 0.2 0.2 D1,E1,B24 0.2 0.2 D2,E2,C24 0.2 0.2 D3,E3,A25 0.2 0.2 D4,E4,B25 0.2 0.2 www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 139 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.14.4.2.5 ADC Timing Diagrams
The following diagrams show the ADC conversion timings for two SOCs given the following assumptions:
- SOC0 and SOC1 are configured to use the same trigger.
- No other SOCs are converting or pending when the trigger occurs.
- The round-robin pointer is in a state that causes SOC0 to convert first.
- ADCINTSEL is configured to set an ADCINT flag upon end of conversion for SOC0 (whether this flag propagates through to the CPU to cause an interrupt is determined by the configurations in the PIE module). Table 6-22 lists the descriptions of the ADC timing parameters. Table 6-23 and Table 6-24 list the ADC timings. SYSCLK ADCTRIG ADCSOCFLG.SOC0 ADCSOCFLG.SOC1 ADC S+H ADCCLK SOC0 Input on SOC0.CHSEL Input on SOC1.CHSELADCRESULT0 ADCRESULT1 ADCINTFLG.ADCINTx SOC1 (old data) (old data) Sample n Sample n+1 Sample n Sample n+1 tSH tLAT tEOC tINT Figure 6-38. ADC Timings for 12-bit Mode in Early Interrupt Mode TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
140 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
ADCSOCFLG.SOC0 ADCSOCFLG.SOC1 ADC S+H ADCCLK SOC0 Input on SOC0.CHSEL Input on SOC1.CHSEL ADCRESULT0 ADCRESULT1 ADCINTFLG.ADCINTx SOC1 (old data) (old data) Sample n Sample n+1 Sample n Sample n+1 tSH tLAT tEOC tINT Figure 6-39. ADC Timings for 12-bit Mode in Late Interrupt Mode www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 141 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 6-22. ADC Timing Parameter Descriptions PARAMETER DESCRIPTION tSH The duration of the S+H window. At the end of this window, the value on the S+H capacitor becomes the voltage to be converted into a digital value. The duration is given by (ACQPS + 1) SYSCLK cycles. ACQPS can be configured individually for each SOC, so tSH is not necessarily the same for different SOCs. Note: The value on the S+H capacitor is captured approximately 5 ns before the end of the S+H window regardless of device clock settings. tLAT The time from the end of the S+H window until the ADC results latch in the ADCRESULTx register. If the ADCRESULTx register is read before this time, the previous conversion results are returned. tEOC The time from the end of the S+H window until the S+H window for the next ADC conversion can begin. The subsequent sample can start before the conversion results are latched. tINT The time from the end of the S+H window until an ADCINT flag is set (if configured). If the INTPULSEPOS bit in the ADCCTL1 register is set, tINT coincides with the end of conversion (EOC) signal. If the INTPULSEPOS bit is 0, tINT coincides with the end of the S+H window. If tINT triggers a read of the ADC result register (directly through DMA or indirectly by triggering an ISR that reads the result), care must be taken to make sure the read occurs after the results latch (otherwise, the previous results are read). If the INTPULSEPOS bit is 0, and the OFFSET field in the ADCINTCYCLE register is not 0, then there is a delay of OFFSET SYSCLK cycles before the ADCINT flag is set. This delay can be used to enter the ISR or trigger the DMA exactly when the sample is ready. tDMA The time from the end of the S+H window until a DMA read of the ADC conversion result is triggered, when ADCCTL1.TDMAEN = 1. If TDMAEN is set to 0, then the DMA trigger occurs at TINT. In certain conditions, the ADCINT flag can be set before the ADCRESULT value is latched. To make sure that the DMA read occurs after the ADCRESULT value has been latched, write 1 to ADCCTL1.TDMAEN to enable DMA timings. TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
142 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 6-23. ADC Timings in 12-bit Mode with SAMPCAPRESETSEL = 0 ADCCLK Prescale SYSCLK Cycles ADCCTL2. PRESCALE Prescale Ratio tEOC tLAT tINT (Early)(1) tINT (Late) tDMA 0 1 15 20 1 15 20 2 2 30 35 1 30 35 3 2.5 38 46 1 38 46 4 3 45 50 1 45 50 5 3.5 53 58 1 53 58 6 4 60 65 1 60 65 7 4.5 68 73 1 68 73 8 5 75 80 1 75 80 9 5.5 83 88 1 83 88 10 6 90 95 1 90 95 11 6.5 98 103 1 98 103 12 7 105 110 1 105 110 13 7.5 113 118 1 113 118 14 8 120 125 1 120 125 15 8.5 128 133 1 128 133 (1) By default, tINT occurs one SYSCLK cycle after the S+H window if INTPULSEPOS is 0. This can be changed by writing to the OFFSET field in the ADCINTCYCLE register. Table 6-24. ADC Timings in 12-bit Mode with SAMPCAPRESETSEL = 1 ADCCLK Prescale SYSCLK Cycles ADCCTL2. PRESCALE Prescale Ratio tEOC tLAT tINT (Early)(1) tINT (Late) tDMA 0 1 14 19 1 14 19 2 2 28 33 1 28 33 3 2.5 35 40 1 35 40 4 3 42 47 1 42 47 5 3.5 49 54 1 49 54 6 4 56 61 1 56 61 7 4.5 63 68 1 63 68 8 5 70 75 1 70 75 9 5.5 77 82 1 77 82 10 6 84 89 1 84 89 11 6.5 91 96 1 91 96 12 7 98 103 1 98 103 13 7.5 105 110 1 105 110 14 8 112 117 1 112 117 15 8.5 119 124 1 119 124 (1) By default, tINT occurs one SYSCLK cycle after the S+H window if INTPULSEPOS is 0. This can be changed by writing to the OFFSET field in the ADCINTCYCLE register. www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 143 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.14.5 Temperature Sensor
6.14.5.1 Temperature Sensor Electrical Data and Timing
The temperature sensor can be used to measure the device junction temperature. The temperature sensor is sampled through an internal connection to the ADC and translated into a temperature through TI-provided software. When sampling the temperature sensor, the ADC must meet the acquisition time in the Temperature Sensor Characteristics table.
6.14.5.1.1 Temperature Sensor Characteristics
over recommended operating conditions (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT Tacc Temperature Accuracy External reference ±15 °C tstartup Start-up time (TSNSCTL[ENABLE] to sampling temperature sensor) 500 µs tacq ADC acquisition time 450 ns TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
144 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.14.6 Comparator Subsystem (CMPSS)
The Comparator Subsystem (CMPSS) consists of analog comparators and supporting circuits that are useful for power applications such as peak current mode control, switched-mode power supply, power factor correction, voltage trip monitoring, and so forth. The comparator subsystem is built around a number of modules. Each subsystem contains two comparators, two reference 12-bit DACs, and two digital filters. The subsystem also includes two ramp generators. The ramp generators ramp up and down. Comparators are denoted "H" or "L" within each module where “H” and “L” represent high and low, respectively. Each comparator generates a digital output which indicates whether the voltage on the positive input is greater than the voltage on the negative input. The positive input of the comparator is driven from an external pin (see the Analog Subsystem chapter of the TMS320F28P55x Real-Time Microcontrollers Technical Reference Manual for mux options available to the CMPSS). The negative input can be driven by an external pin or by the programmable reference 12-bit DAC. Each comparator output passes through a programmable digital filter that can remove spurious trip signals. An unfiltered output is also available if filtering is not required. Two ramp generator circuits are optionally available to control the reference 12-bit DAC values for the high and low comparators in the subsystem. The DAC along with a wrapper can be used to generate a ramp which is used for slope compensation in Peak Current Mode Control (PCMC) and other applications. Each CMPSS includes:
- Two analog comparators
- Two independently programmable reference 12-bit DACs
- Dual decrementing/incrementing ramp generators
- Two digital filters with max filter clock prescale of 224
- Ability to synchronize submodules with EPWMSYNCPER
- Ability to extend clear signal with EPWMBLANK
- Ability to synchronize output with SYSCLK
- Ability to latch output
- Ability to invert output
- Option to use hysteresis on the input
- Option for negative input of comparator to be driven by an external signal or by the reference DAC
- Option for positive input of comparator to be driven by an external signal or by the PGA
- Option to use the low comparator DAC output, CMPx_DACL, on an external pin (select instances only, mutually exclusive with use of compare functionality)
- External connection to CMPSS filters
- Supports connection with ePWM for diode emulation
- Ramp generator prescaler
- Wake-up from standby and halt LPM (Low Power Modes) triggered by CMPSS trip outputs
6.14.6.1 CMPx_DACL
Some CMPSS module instances have support for DAC output buffered to a pin. This CMPx_DACL output from the CMPSS module uses the low-side DAC of the CMPSS module specified. When using DAC output from a CMPSS instance, all other CMPSS module features for that instance are unavailable. For CMPx_DACL instances available for a particular device, please see the DAC column of the Analog Pins and Internal Connections table. See the Buffered Output from CMPx_DACL Electrical Characteristics section for DAC output capabilities. www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 145 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.14.6.2 CMPSS Connectivity Diagram
CMP1_LN CTRIP1H CTRIPOUT1H ePWM X-BAR ePWMs CTRIP1H CTRIP1L CTRIP2H CTRIP2L CTRIP4H CTRIP4L Output X-BAR GPIO Mux CTRIPOUT1H CTRIPOUT1L CTRIPOUT2H CTRIPOUT2L CTRIPOUT4H CTRIPOUT4L CMP1_DACL CMP1_HP CMP1_HN CMP1_LP Comparator Subsystem 2 CMP2_HP CMP2_HN CMP2_LN CMP2_LP CTRIP3L CTRIPOUT3L VDDA Digital Filter Digital Filter DAC12 DAC12 CTRIP3H CTRIPOUT3H Comparator Subsystem 3 CMP3_HP CMP3_HN CMP3_LN CMP3_LP CTRIP4L CTRIPOUT4L VDDA Digital Filter Digital Filter DAC12 DAC12 CTRIP4H CTRIPOUT4H Comparator Subsystem 4 CMP4_HP CMP4_HN CMP4_LN CMP4_LP CTRIP3H CTRIP3L CTRIPOUT3H CTRIPOUT3L CMPSS Module GPIO Mux ePWM X-BAR ePWMs Output X-BAR Figure 6-40. CMPSS Connectivity TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
146 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.14.6.3 Block Diagram
The block diagram for the CMPSS is shown in Figure 6-41.
- CTRIPx(x= "H" or "L") signals are connected to the ePWM X-BAR for ePWM trip response. See the Enhanced Pulse Width Modulator (ePWM) chapter of the for more details on the ePWM X-BAR mux configuration.
- CTRIPxOUTx(x= "H" or "L") signals are connected to the Output X-BAR for external signaling. See the General-Purpose Input/Output (GPIO) chapter of the for more details on the Output X-BAR mux configuration. SYSCLK CMPx_HP CMPx_HN COMPCTL[ASYNCHEN] COMPSTS[COMPHLATCH] COMPCTL[CTRIPOUTHSEL] COMPCTL[CTRIPHSEL] CTRIPH CTRIPOUTH To EPWM X-BAR To OUTPUT X-BAR COMPSTS[COMPHSTS] SYNCH ASYNCHSYSCLK COMPSTS[COMPHSTS] EPWM1SYNCPER COMPDACLCTL[RAMPSOURCE]+ 16*COMPDACLCTL2[RAMPSOURCEUSEL] EPWM2SYNCPER EPWM3SYNCPER EPWMnSYNCPER ... EPWMSYNCPER_H COMPSTSCLR[HSYNCCLREN] COMPSTSCLR[HLATCHCLR] COMPSTSCLR[LSYNCCLREN] SYSCLK COMPDACHCTL[SWLOADSEL] COMPDACHCTL[DACSOURCE] COMPCTL[COMPHSOURCE] COMPCTL[COMPHINV] COMPDACHCTL[SWLOADSEL] SYSCLK CMPx_LP CMPx_LNDACLVALA COMPCTL[ASYNCLEN] COMPCTL[COMPLSOURCE] COMPCTL[COMPLINV] COMPSTSCLR[LLATCHCLR] COMPSTS[COMPLLATCH] COMPCTL[CTRIPOUTLSEL] COMPCTL[CTRIPLSEL] CTRIPL CTRIPOUTL To EPWM X-BAR To OUTPUT X-BAR COMPSTS[COMPLSTS] SYNCL ASYNCL DACHVALA D Q D Q DACHVALS Ramp Generator(H) D Q D Q 12-bit DACH 12-bit DACL D Q > Digital Filter S R Q OR OR Digital Filter D Q> OR R Q S OR EPWM1BLANK EPWM2BLANK EPWM3BLANK EPWMnBLANK ... COMPDACLCTL[BLANKSOURCE]+ 16*COMPDACLCTL2[BLANKSOURCEUSEL] OR ANDCOMPDACHCTL[BLANKEN] EPWMBLANK_H R R R R EN EN Bu er CMPxDACOUTEN (from Analog Subsystem) Enable CMPxDACL To Pin >>1 Ramp Generator(L) COMPSTS[COMPLSTS] n EXT_FILTIN_H CTRIPHFILCTL[FILTINSEL] n EXT_FILTIN_L CTRIPLFILCTL[FILTINSEL] 0 0 AND OR EPWMBLANK_L COMPDACLCTL[BLANKEN] EPWMSYNCPER_L COMPDACHCTL[RAMPSOURCE]+ 16*COMPDACHCTL2[RAMPSOURCEUSEL] COMPDACHCTL[BLANKSOURCE]+ 16*COMPDACHCTL2[BLANKSOURCEUSEL] COMPDACLCTL[DACSOURCE] COMPDACHCTL2[XTRIGCFG] To LPM Wakeup To LPM Wakeup DACLVALS EPWMSYNCPER_H COMPSTS[COMPLSTS] TRIGSYNCH 2 1|0 COMPDACHCTL2[XTRIGCFG] EPWMSYNCPER_L COMPSTS[COMPHSTS] TRIGSYNCL 1 2|0 COMPL COMPH Comparator Digital Filter Output MUX Ramp generator n-1 CMPSS DAC n-1 CMPSS Buffered DAC A. CMPxDACL only exists for the CMPSS 1 module on this device. B. Enabling the DACL to a pin disables all other functionality: DACH, both COMP, the Ramp Generator, and the digital filters. Figure 6-41. CMPSS Module Block Diagram Each reference 12-bit DAC can be configured to drive a reference voltage into the negative input of the respective comparator. Some CMPSS instances also allow the low DAC output to be routed to a pin to act as an external DAC. In this case, all other CMPSS module functionality is not useable, including the high DAC, both comparators, ramp generation, and the digital filters. The reference 12-bit DAC is illustrated in Figure 6-42. To COMPH To COMPL VDDA VSSA DACHVALA 12-bit DACH DACLVALA 12-bit DACL DACOUTH DACOUTL DACREF Figure 6-42. Reference DAC Block Diagram www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 147 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.14.6.4 CMPSS Electrical Data and Timing
6.14.6.4.1 CMPSS Comparator Electrical Characteristics
over recommended operating conditions (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT TPU Power-up time 500 µs Comparator input (CMPINxx) range 0 VDDA V Input referred offset error Low common mode, inverting input set to 50mV –20 20 mV Hysteresis(1) 1x 4 12 20 LSB 2x 17 24 33 3x 25 36 50 4x 30 48 67 Response time (delay from CMPINx input change to output on ePWM X-BAR or Output X-BAR) Step response 21 60 ns Ramp response (1.65V/µs) 26 Ramp response (8.25mV/µs) 30 ns PSRR Power Supply Rejection Ratio Up to 250 kHz 46 dB CMRR Common Mode Rejection Ratio 40 dB (1) The CMPSS DAC is used as the reference to determine how much hysteresis to apply. Therefore, hysteresis will scale with the CMPSS DAC reference voltage. Hysteresis is available for all comparator input source configurations. CMPSS Comparator Input Referred Offset and Hysteresis CTRIPx = 0
0 CMPINxN or
CTRIPx = 1 Input Referred Offset COMPINxP Voltage CTRIPx Logic Level Figure 6-43. CMPSS Comparator Input Referred Offset CTRIPx = 0 CTRIPx = 1 Hysteresis COMPINxP Voltage CTRIPx Logic Level Figure 6-44. CMPSS Comparator Hysteresis TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
148 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.14.6.4.2 CMPSS DAC Static Electrical Characteristics
over recommended operating conditions (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT CMPSS DAC output range Internal reference 0 VDDA V Static offset error(1) –25 25 mV Static gain error(1) –2 2 % of FSR Static DNL Endpoint corrected >–1 4 LSB Static INL Endpoint corrected –16 16 LSB Settling time Settling to 1LSB after full-scale output change 1 µs Resolution 12 bits CMPSS DAC output disturbance(2) Error induced by comparator trip or CMPSS DAC code change within the same CMPSS module –100 100 LSB CMPSS DAC disturbance time(2) 200 ns (1) Includes comparator input referred errors. (2) Disturbance error may be present on the CMPSS DAC output for a certain amount of time after a comparator trip.
6.14.6.4.3 CMPSS Illustrative Graphs
Figure 6-45. CMPSS DAC Static Offset www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 149 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Figure 6-46. CMPSS DAC Static Gain Linearity Error Figure 6-47. CMPSS DAC Static Linearity
6.14.6.4.4 Buffered Output from CMPx_DACL Operating Conditions
over recommended operating conditions (unless otherwise noted)(1) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT RL Resistive Load(2) 5 kΩ CL Capacitive Load 100 pF TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
150 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.14.6.4.4 Buffered Output from CMPx_DACL Operating Conditions (continued)
over recommended operating conditions (unless otherwise noted)(1) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT VOUT Valid Output Voltage Range(3) RL = 5 kΩ 0.3 VDDA – 0.3 V RL = 1 kΩ 0.6 VDDA – 0.6 V Reference Voltage(4) VREFHI 2.4 2.5 or 3.0 VDDA V (1) Typical values are measured with VREFHI = 3.3 V and VREFLO = 0 V, unless otherwise noted. Minimum and maximum values are tested or characterized with VREFHI = 2.5 V and VREFLO = 0 V. (2) DAC can drive a minimum resistive load of 1 kΩ, but the output range will be limited. (3) This is the linear output range of the DAC. The DAC can generate voltages outside this range, but the output voltage will not be linear due to the buffer. (4) For best PSRR performance, VREFHI should be less than VDDA.
6.14.6.4.5 Buffered Output from CMPx_DACL Electrical Characteristics
over recommended operating conditions (unless otherwise noted)(1) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT General Resolution(4) 12 bits Load Regulation –1 1 mV/V Glitch Energy 1.5 V-ns Voltage Output Settling Time Full-Scale Settling to 2 LSBs after 0.3V- to-3V transition 2 µs Voltage Output Settling Time 1/4th Full-Scale Settling to 2 LSBs after 0.3V- to-0.75V transition 1.6 µs Voltage Output Slew Rate Slew rate from 0.3V-to-3V transition 2.8 4.5 V/µs Load Transient Settling Time 5-kΩ Load 328 ns TPU Power Up Time Bandgap Not Enabled 500 µs DC Characteristics Offset Offset Error –100 100 mV Gain Gain Error(2) –1.5 1.5 % of FSR DNL Differential Non Linearity(4) Endpoint corrected –2 2 LSB (12-bit) INL Integral Non Linearity Endpoint corrected –7 7 LSB (12-bit) AC Characteristics Output Noise Integrated noise from 100 Hz to 100 kHz 600 µVrms Noise density at 10 kHz 800 nVrms/√Hz SNR Signal to Noise Ratio 1 kHz, 200 KSPS 64 dB THD Total Harmonic Distortion 1 kHz, 200 KSPS –64.2 dB SFDR Spurious Free Dynamic Range 1 kHz, 200 KSPS 66 dB SINAD Signal to Noise and Distortion Ratio 1 kHz, 200 KSPS 61.7 dB PSRR Power Supply Rejection Ratio(3) DC 70 dB 100 kHz 30 dB (1) Typical values are measured with VREFHI = 3.3 V and VREFLO = 0 V, unless otherwise noted. Minimum and maximum values are tested or characterized with VREFHI = 2.5 V and VREFLO = 0 V. (2) Gain error is calculated for linear output range. (3) VREFHI = 3.2 V, VDDA = 3.3 V DC + 100 mV Sine. (4) 11-bit effective (monotonic response). www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 151 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.14.7 Buffered Digital-to-Analog Converter (DAC)
The buffered DAC module consists of an internal 12-bit DAC and an analog output buffer that can drive an external load. For driving even higher loads than typical, a trade-off can be made between load size and output voltage swing. For the load conditions of the buffered DAC, see the Buffered DAC Electrical Data and Timing section. The buffered DAC is a general-purpose DAC that can be used to generate a DC voltage or AC waveforms such as sine waves, square waves, triangle waves and so forth. Software writes to the DAC value register can take effect immediately or can be synchronized with EPWMSYNCO events. Each buffered DAC has the following features:
- 12-bit resolution
- Selectable reference voltage source
- x1 and x2 gain modes when using internal VREFHI
- Ability to synchronize with EPWMSYNCPER EPWM1SYNCPER VREFHI VDDA VSSA DACCTL[MODE] (Select x1 or x2 gain) DACCTL[DACREFSEL] DACCTL[LOADMODE]SYSCLK DACCTL[SYNCSEL] EPWM2SYNCPER EPWM3SYNCPER EPWMnSYNCPER ... D Q D Q DACVALS DACVALA 12-bit DAC VSSA DACOUT DACREF Internal Reference Circuit ANAREFx1P65SEL ANAREFPCTL[REFPMUXSELx] EN 1.65 V 2.5 V n-1 ... Reference Voltage Source Output Bu er 12-Bit DAC Internal Reference Circuit DAC Module A. VDAC is not available for this device; so, VREFHI and VSSA are the reference voltages. Figure 6-48. DAC Module Block Diagram TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
152 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.14.7.1 Buffered DAC Electrical Data and Timing
6.14.7.1.1 Buffered DAC Operating Conditions
over recommended operating conditions (unless otherwise noted)(1) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT RL Resistive Load(2) 5 kΩ CL Capacitive Load 100 pF VOUT Valid Output Voltage Range(3) RL = 5 kΩ 0.3 VDDA – 0.3 V RL = 1 kΩ 0.6 VDDA – 0.6 V Reference Voltage(4) VREFHI 2.4 2.5 or 3.0 VDDA V (1) Typical values are measured with VREFHI = 3.3 V and VREFLO = 0 V, unless otherwise noted. Minimum and maximum values are tested or characterized with VREFHI = 2.5 V and VREFLO = 0 V. (2) DAC can drive a minimum resistive load of 1 kΩ, but the output range will be limited. (3) This is the linear output range of the DAC. The DAC can generate voltages outside this range, but the output voltage will not be linear due to the buffer. (4) For best PSRR performance, VREFHI should be less than VDDA.
6.14.7.1.2 Buffered DAC Electrical Characteristics
over recommended operating conditions (unless otherwise noted)(1) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT General Resolution 12 bits Load Regulation –1 1 mV/V Glitch Energy 1.5 V-ns Voltage Output Settling Time Full-Scale Settling to 2 LSBs after 0.3V- to-3V transition 2 µs Voltage Output Settling Time 1/4th Full-Scale Settling to 2 LSBs after 0.3V- to-0.75V transition 1.6 µs Voltage Output Slew Rate Slew rate from 0.3V-to-3V transition 2.8 4.5 V/µs Load Transient Settling Time 5-kΩ Load 328 ns 1-kΩ Load 557 ns Reference Input Resistance(2) VREFHI 160 200 240 kΩ TPU Power Up Time External Reference mode 500 µs Internal Reference mode 5000 µs DC Characteristics Offset Offset Error Midpoint –10 10 mV Gain Gain Error(3) –2.5 2.5 % of FSR DNL Differential Non Linearity(4) Endpoint corrected –1 ±0.4 1 LSB INL Integral Non Linearity Endpoint corrected –5 ±2 5 LSB AC Characteristics Output Noise Integrated noise from 100 Hz to 100 kHz 600 µVrms Noise density at 10 kHz 800 nVrms/√Hz SNR Signal to Noise Ratio 1 kHz, 200 KSPS 64 dB THD Total Harmonic Distortion 1 kHz, 200 KSPS –64.2 dB SFDR Spurious Free Dynamic Range 1 kHz, 200 KSPS 66 dB SINAD Signal to Noise and Distortion Ratio 1 kHz, 200 KSPS 61.7 dB www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 153 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.14.7.1.2 Buffered DAC Electrical Characteristics (continued)
over recommended operating conditions (unless otherwise noted)(1) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT PSRR Power Supply Rejection Ratio(5) DC 70 dB 100 kHz 30 dB (1) Typical values are measured with VREFHI = 3.3 V and VREFLO = 0 V, unless otherwise noted. Minimum and maximum values are tested or characterized with VREFHI = 2.5 V and VREFLO = 0 V. (2) Per active Buffered DAC module. (3) Gain error is calculated for linear output range. (4) The DAC output is monotonic. (5) VREFHI = 3.2 V, VDDA = 3.3 V DC + 100 mV Sine. TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
154 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.14.8 Programmable Gain Amplifier (PGA)
The Programmable Gain Amplifier (PGA) is used to amplify an input voltage for the purpose of increasing the effective resolution of the downstream ADC and CMPSS modules. The integrated PGA helps to reduce cost and design effort for many control applications that traditionally require external, stand-alone amplifiers. On-chip integration ensures that the PGA is compatible with the downstream ADC and CMPSS modules. Software-selectable gain and filter settings make the PGA adaptable to various performance needs. The PGA has the following features:
- Rail to rail input and output voltage within VDDA and VSSA range
- Programmable gain modes including unity gain and other values from 2X - 64X
- Standalone gain mode using off-chip passive components
- Post-gain filtering using on-chip resistors
- Differential input support
- Hardware assisted chopping for offset reduction
- Support for Kelvin ground connections using PGA_INM pins The active component in the PGA is an embedded operational amplifier (op amp) that is configured as a non-inverting or inverting amplifier with internal feedback resistors. These internal feedback resistor values are paired to produce software selectable voltage gains. Three PGA signals are available at the device pins:
- PGA_INP is the positive input to the PGA op-amp.
- PGA_INM is the negative input to the PGA op-amp. See the device data manual for more information.
- PGA_OUT supports op-amp output filtering with RC components. The filtered signal is available for sampling and monitoring by on-chip ADC and CMPSS modules. PGA_OUT_INT is an internal signal at the op amp output. It is available for sampling and monitoring by the internal ADC and CMPSS modules. Figure 6-49 shows the PGA block diagram. VSSA VDDA Rib PGA_OUT Ria PGA_INP PGA_INM To ADC and CMPSS RFILT To ADC and CMPSS PGA_OUTENABLE & FILT_RES_SEL=0 PGA_OUTENABLE FILT_RES_SEL PGA_OUTENABLE & FILT_RES_SEL OUT_EN_INTGAIN & FILT_RES_SEL=0 PGA_OUT_INT Figure 6-49. PGA Block Diagram www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 155 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.14.8.1 PGA Electrical Data and Timing
6.14.8.1.1 PGA Operating Conditions
over recommended operating conditions (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT PGA Output Range(1) VSSA+0.025 VDDA-0.025 V Cap Load on PGA Out 40 pF (1) This is the linear output range of the PGA. The PGA can output voltages outside this range, but the voltages will not be linear.
6.14.8.1.2 PGA Characteristics
over recommended operating conditions (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT General Min ADC S+H (No Filter; All Gain Settings; Single ADC Driven) Settling within ±1 ADC LSB Accuracy 400 ns Min ADC S+H (No Filter; All Gain Settings; Two ADC Driven) Settling within ±1 ADC LSB Accuracy 450 ns Min ADC S+H (With Filter;All Gain Settings) Settling within ±1 ADC LSB Accuracy 450(5) ns Gain Settings -63 Input Bias Current 2 nA Short Circuit Current 41 mA Full Scale Step Response (No Filter) Settling within ±1 ADC LSB Accuracy 450 ns Settling Time Gain Switching 10 µs Slew Rate Naked OPA Mode 10.9 V/µs Slew Rate Gain = 1 10 V/µs Gain = 2/-1 21 V/µs Gain = 4/-3 39 V/µs Gain = 8/-7 56 V/µs Gain = 16/-15 46 V/µs Gain = 32/-31 29 V/µs Gain = 64/-63 25 V/µs Ria Gain = 1 256 kΩ Gain = 2/-1 16 kΩ Gain = 4/-3 8 kΩ Gain = 8/-7 8 kΩ Gain = 16/-15 8 kΩ Gain = 32/-31 8 kΩ Gain = 64/-63 4 kΩ TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
156 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.14.8.1.2 PGA Characteristics (continued)
over recommended operating conditions (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT Rib Gain = 1 0 kΩ Gain = 2/-1 16 kΩ Gain = 4/-3 24 kΩ Gain = 8/-7 56 kΩ Gain = 16/-15 128 kΩ Gain = 32/-31 248 kΩ Gain = 64/-63 252 kΩ Filter Resistor Targets RFILT = 800 Ω 800 Ω RFILT = 400 Ω 400 Ω RFILT = 200 Ω 200 Ω RFILT = 100 Ω 100 Ω RFILT = 50 Ω 50 Ω Gain Bandwidth Product Gain=1 7 MHz Gain Bandwidth Product Gain=1 7 MHz Closed Loop -3bd BW Gain=1 15 MHz Gain=2/-1 13.7 MHz Gain=4/-3 10.5 MHz Gain=8/-7 9.5 MHz Gain=16/-15 5.8 MHz Gain=32/-31 3.8 MHz Gain=64/-63 3.25 MHz DC Characteristics Gain Error(1) Gain = 1 +/-0.18 % Gain Error(1) Gain = 2, -1 +/-0.37 % Gain Error(1) Gain = 4, -3 +/-0.6 % Gain Error(1) Gain = 8, -7 +/-0.73 % Gain Error(1) Gain = 16, -15 +/-0.81 % Gain Error(1) Gain = 32, -31 +/-1.0 % Gain Error(1) Gain = 64, -63 +/-1.82 % Offset Error(2) Input Referred +/-1.0 mV Offset Temp Coefficient Input Referred ±3.0 µV/C Offset Error - Chopped +/-0.8 mV Offset Temp Coefficient - Chopped 0.3 µV/C DC Code Spread 2.5 12b LSB AC Characteristics Bandwidth(3) All Gain Modes 7 MHz THD(4) DC –78 dB Up to 100 kHz –70 dB CMRR DC –60 dB Up to 100 kHz –50 dB PSRR(4) DC –75 dB Up to 100 kHz –50 dB Noise PSD(4) 1 kHz 200 nV/sqrt(Hz) www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 157 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
over recommended operating conditions (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT Integrated Noise (Input Referred)(4) 3 Hz to 30 MHz 100 µV (1) Includes ADC gain error. (2) Includes ADC offset error. (3) 3dB bandwidth. (4) Performance of PGA alone. (5) Step response time (max) = 450ns + 7.6*Rfilt* Cfilt TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
158 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.15 Control Peripherals
6.15.1 Enhanced Pulse Width Modulator (ePWM)
The ePWM peripheral is a key element in controlling many of the power electronic systems found in both commercial and industrial equipment. The ePWM type-4 module is able to generate complex pulse width waveforms with minimal CPU overhead by building the peripheral up from smaller modules with separate resources that can operate together to form a system. Some of the highlights of the ePWM type-4 module include complex waveform generation, dead-band generation, a flexible synchronization scheme, advanced trip-zone functionality, and global register reload capabilities. The ePWM and eCAP synchronization scheme on the device provides flexibility in partitioning the ePWM and eCAP modules and allows localized synchronization within the modules. Figure 6-50 shows the ePWM module. Figure 6-51 shows the ePWM trip input connectivity. www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 159 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
DCBEVT1/sync(A) EPWMxSYNCI TBCTL[SWFSYNC] ePWM SYNC Scheme EXTSYNCIN EXTSYNCOUT CMPC Active (16) CMPC Shadow (16) CMPD Active (16) CMPD Shadow (16) CMPB Active (16) CMPB Shadow (16) CMPA Active (24) CMPA Shadow (24) CTR=CMPA CMPAHR (8) CTR=CMPC CTR=CMPD Action Qualifier (AQ) Dead Band (DB) EPWMA EPWMB PWM Chopper (DB) Trip Zone (TZ) Time-Base (TB) TBPHS Active (24) TBCTR Active (16) Counter Up/Down (16 bit) TBPRD Active (24) TBPRD Shadow (24) CTR=PRD TBCTL[PHSEN] CTR=ZERO CTR_Dir Phase Control TBPHSHR (8) 816 Event Trigger And Interrupt (ET) CTR=PRD CTR=ZERO CTR=PRD or ZERO CTR=CMPA CTR=CMPB CTR=CMPC CTR_Dir CTR=CMPD DCAEVT1.soc(A) DCBEVT1.soc(A) EPWMx_INT On-chip ADC EPWMxSOCA EPWMxSOCB Select and pulse stretch for external ADC ADCSOCOUTSELECT ADCSOCAO ADCSOCBO ePWMxA ePWMxB CTR=ZERO DCAEVT1.inter DCBEVT1.inter DCAEVT2.inter DCBEVT2.inter EPWMx_TZ_INT TZ1 to TZ3 EMUSTOP CLOCKFAIL EQEPxERR DCAEVT1.force(A) DCBEVT1.force(A) DCAEVT2.force(A) DCBEVT2.force(A) Counter Compare (CC) HiRes PWM (HRPWM) CMPAHR (8) CMPBHR (8) CTR=CMPB CMPBHR (8) TBCNT (16) TBCNT (16) CMPC[15-0] 16 CMPD[15-0] 16 TBPRDHR (8) DCAEVT1/sync(A) A. These events are generated by the ePWM digital compare (DC) submodule based on the levels of the TRIPIN inputs. Figure 6-50. ePWM Submodules and Critical Internal Signal Interconnects TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
160 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Figure 6-51. ePWM Trip Input Connectivity www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 161 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.15.1.1 Control Peripherals Synchronization
The ePWM and eCAP synchronization scheme on the device provides flexibility in partitioning the ePWM and eCAP modules and allows localized synchronization within the modules. Figure 6-52 shows the synchronization scheme. EPWMSYNCOUTEN SWEN ZEROEN CMPBEN CMPCEN CMPDEN DCARVT1EN DCBEVT1EN TBCTL CTR=ZERO CTR=CMPB CTR=CMPC CTR=CMPD DCAEVT1.sync DCBEVT1.sync OR :ULWH³1´WR GLDCTL2[OSHTLD] One Shot Latch Set Q CLR :ULWH³1´WR TBCTL2[OSHTSYNC] TBCTL3[OSSFRCEN] TBCTL2[OSHTSYNCMODE] EPWMxSYNCOUT TBCTL2[SELFCLRTRREM] Clear Register EPWMSYNCINSEL Disable EPWM1SYNCOUT EPWMxSYNCOUT ECAP1SYNCOUT ECAPySYNCOUT Other Sources EPWMxSYNCIN HRPCTL[PWMSYNCSELX] CTR=CMPC UP CTR=CMPC DOWN CTR=CMPD UP CTR=CMPD DOWN CTR=PRD CTR=ZERO HRPCTL[PWMSYNCSEL] EPWMxSYNCPER SWFSYNC CMPSS DAC Note: SYNCO and SYNCOUT are used interchangeably Figure 6-52. Synchronization Chain Architecture TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
162 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.15.1.2 ePWM Electrical Data and Timing For an explanation of the input qualifier parameters, see the General-Purpose Input Timing Requirements table. 6.15.1.2.1 ePWM Timing Requirements MIN MAX UNIT tw(SYNCIN) Sync input pulse width Asynchronous 2tc(EPWMCLK) cyclesSynchronous 2tc(EPWMCLK) With input qualifier 1tc(EPWMCLK) + tw(IQSW) 6.15.1.2.2 ePWM Switching Characteristics over recommended operating conditions (unless otherwise noted) PARAMETER(1) MIN MAX UNIT tw(PWM) Pulse duration, PWMx output high/low 20 ns tw(SYNCOUT) Sync output pulse width 8tc(SYSCLK) cycles td(TZ-PWM) Delay time, trip input active to PWM forced high Delay time, trip input active to PWM forced low Delay time, trip input active to PWM Hi-Z 25 ns (1) 20-pF load on pin.
6.15.1.2.3 Trip-Zone Input Timing
For an explanation of the input qualifier parameters, see the General-Purpose Input Timing Requirements table. MIN MAX UNIT tw(TZ) Pulse duration, TZx input low Asynchronous 1tc(EPWMCLK) cycles Synchronous 2tc(EPWMCLK) cycles With input qualifier 1tc(EPWMCLK) + tw(IQSW) cycles PWM (B) TZ (A) EPWMCLK tw(TZ) td(TZ-PWM) A. TZ: TZ1, TZ2, TZ3, TRIP1–TRIP12 B. PWM refers to all the PWM pins in the device. The state of the PWM pins after TZ is taken high depends on the PWM recovery software. Figure 6-53. PWM Hi-Z Characteristics www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 163 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.15.2 High-Resolution Pulse Width Modulator (HRPWM)
The HRPWM combines multiple delay lines in a single module and a simplified calibration system by using a dedicated calibration delay line. For each ePWM module, there are two HR outputs:
- HR Duty and Deadband control on Channel A
- HR Duty and Deadband control on Channel B The HRPWM module offers PWM resolution (time granularity) that is significantly better than what can be achieved using conventionally derived digital PWM methods. The key points for the HRPWM module are:
- Significantly extends the time resolution capabilities of conventionally derived digital PWM
- This capability can be used in both single edge (duty cycle and phase-shift control) as well as dual edge control for frequency/period modulation.
- Finer time granularity control or edge positioning is controlled through extensions to the Compare A, B, phase, period and deadband registers of the ePWM module.
6.15.2.1 HRPWM Electrical Data and Timing
6.15.2.1.1 High-Resolution PWM Characteristics
PARAMETER MIN TYP MAX UNIT Micro Edge Positioning (MEP) step size(1) 150 310 ps (1) The MEP step size will be largest at high temperature and minimum voltage on VDD. MEP step size will increase with higher temperature and lower voltage and decrease with lower temperature and higher voltage. Applications that use the HRPWM feature should use MEP Scale Factor Optimizer (SFO) estimation software functions. See the TI software libraries for details of using SFO functions in end applications. SFO functions help to estimate the number of MEP steps per SYSCLK period dynamically while the HRPWM is in operation.
6.15.3 External ADC Start-of-Conversion Electrical Data and Timing
6.15.3.1 External ADC Start-of-Conversion Switching Characteristics
over recommended operating conditions (unless otherwise noted) PARAMETER MIN MAX UNIT tw(ADCSOCL) Pulse duration, ADCSOCxO low 32tc(SYSCLK) cycles
6.15.3.2 ADCSOCAO or ADCSOCBO Timing Diagram
tw(ADCSOCL) Figure 6-54. ADCSOCAO or ADCSOCBO Timing TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
164 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.15.4 Enhanced Capture (eCAP)
The features of the eCAP module include:
- Speed measurements of rotating machinery (for example, toothed sprockets sensed by way of Hall sensors)
- Elapsed time measurements between position sensor pulses
- Period and duty cycle measurements of pulse train signals
- Decoding current or voltage amplitude derived from duty cycle encoded current/voltage sensors The eCAP module features described in this chapter include:
- 4-event time-stamp registers (each 32 bits)
- Edge polarity selection for up to four sequenced time-stamp capture events
- Interrupt on either of the four events
- Single-shot capture of up to four event time-stamps
- Continuous mode capture of time stamps in a four-deep circular buffer
- Absolute time-stamp capture
- Difference (Delta) mode time-stamp capture
- When not used in capture mode, the eCAP module can be configured as a single-channel PWM output The capture functionality of the Type 1 eCAP is enhanced from the Type 0 eCAP with the following added features:
- Event filter reset bit – Writing a 1 to ECCTL2[CTRFILTRESET] clears the event filter, the modulo counter, and any pending interrupts flags. Resetting the bit is useful for initialization and debug.
- Modulo counter status bits – The modulo counter (ECCTL2 [MODCNTRSTS]) indicates which capture register is loaded next. In the Type 0 eCAP, to know the current state of the modulo counter was not possible
- DMA trigger source – eCAPxDMA was added as a DMA trigger. CEVT[1-4] can be configured as the source for eCAPxDMA.
- Input multiplexer – ECCTL0 [INPUTSEL] selects one of 128 input signals, which are detailed in the Configuring Device Pins for the eCAP section of the Enhanced Capture (eCAP) chapter in the .
- EALLOW protection – EALLOW protection was added to critical registers. To maintain software compatibility with Type-0, configure DEV_CFG_REGS.ECAPTYPE to make these registers unprotected. The capture functionality of the Type 2 eCAP is enhanced from the Type 1 eCAP with the following added features:
- Added ECAPxSYNCINSEL register – ECAPxSYNCINSEL register is added for each eCAP to select an external SYNCIN. Every eCAP can have a separate SYNCIN signal. www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 165 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.15.4.1 eCAP Block Diagram TSCTR (counter−32 bit) RST CAP1 (APRD Active) LD CAP2 (ACMP Active) LD CAP3 (APRD Shadow) LD CAP4 ECCTL2[CTRFILTRESET] (ACMP Shadow) LD Continuous / Oneshot Capture Control LD1 LD2 LD3 LD4 MODCNTRSTS PRD [0−31] CMP [0−31] CTR [0−31] Interrupt Trigger and Flag Control CTR=CMP HR Input Capture Pulse ACMP shadow Event Prescale CTRPHS (phase register−32 bit) ECAPxSYNCOUT ECAPxSYNCIN Event qualifier Polarity Select Polarity Output Input Select X-Bar X-Bar Polarity Select Polarity Select CTR=PRD CTR_OVF PWM Compare Logic CTR [0−31] PRD [0−31] CMP [0−31] CTR=CMP CTR=PRD CTR_OVFOVF APWM Mode Delta−Mode SYNC APRD shadow ECCTL2 [ SYNCI_EN, SYNCOSEL, SWSYNC] ECCTL2[CAP/APWM] Edge Polarity Select ECCTL1[CAPxPOL] ECCTL1 [ CAPLDEN, CTRRSTx] ECCTL2 [ REARM, CONT_ONESHT, STOP_WRAP] Registers: ECEINT, ECFLG, ECCLR, ECFRC [127:16] HR SubmoduleHRCLK HRCTRL[HRE] HRCTRL[HRE] SYSCLK HRCTRL[HRE] HRCTRL[HRE] HRCTRL[HRE] ECCTL1[PRESCALE] Other Sources [15:0] ECAPx (to ePIE) ECAPx_HRCAL (to ePIE) Figure 6-55. eCAP Block Diagram TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
166 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.15.4.2 eCAP Synchronization The eCAP modules can be synchronized with each other by selecting a common SYNCIN source. SYNCIN source for eCAP can be either software sync-in or external sync-in. The external sync-in signal can come from EPWM, eCAP, or X-Bar. The SYNC signal is defined by the selection in the ECAPxSYNCINSEL[SEL] bit for ECAPx as shown in Figure 6-56. ECAPx ECCTL2[SWSYNC] CTR=PRD Disable Disable ECCTL2[SYNCOSEL] ECAPSYNCINSEL[SEL] 0x0 0x1 0xn Disable ECAPxSYNCOUT ECAPxSYNCIN ECAPxSYNCIN Signals (EPWM, ECAP, INPUTXBAR, «) EPWMxSYNCOUT SYNCSELECT[SYNCOUT] EXTSYNCOUT Figure 6-56. eCAP Synchronization Scheme 6.15.4.3 eCAP Electrical Data and Timing 6.15.4.3.1 eCAP Timing Requirements MIN NOM MAX UNIT tw(CAP) Capture input pulse width Asynchronous 2tc(SYSCLK) nsSynchronous 2tc(SYSCLK) With input qualifier 1tc(SYSCLK) + tw_(IQSW) 6.15.4.3.2 eCAP Switching Characteristics over recommended operating conditions (unless otherwise noted) PARAMETER MIN TYP MAX UNIT tw(APWM) Pulse duration, APWMx output high/low 20 ns www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 167 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.15.5 Enhanced Quadrature Encoder Pulse (eQEP)
The eQEP module on this device is Type-2. The eQEP interfaces directly with linear or rotary incremental encoders to obtain position, direction, and speed information from rotating machines used in high-performance motion and position control systems. The eQEP peripheral contains the following major functional units (see Figure 6-57):
- Programmable input qualification for each pin (part of the GPIO MUX)
- Quadrature decoder unit (QDU)
- Position counter and control unit for position measurement (PCCU)
- Quadrature edge-capture unit for low-speed measurement (QCAP)
- Unit time base for speed/frequency measurement (UTIME)
- Watchdog timer for detecting stalls (QWDOG)
- Quadrature Mode Adapter (QMA) QWDTMR QWDPRD QWDOGUTIME QUPRD QUTMR UTOUT WDTOUT Quadrature capture unit (QCAP) QCPRDLA T QCTMRLA T QFLG QEPSTS QEPCTL Registers used by multiple units QCLK QDIR QI QS PHE PCSOUT Quadrature decoder (QDU) QDECCTL Position counter/ control unit (PCCU)QPOSLA T QPOSSLAT QPOSILA T EQEPxAIN EQEPxBIN EQEPxIIN EQEPxIOUT EQEPxIOE EQEPxSIN EQEPxSOUT EQEPxSOE GPIO MUX EQEPx_A EQEPx_B EQEPx_STROBE EQEPx_INDEX QPOSCMP QEINT QFRC QCLR QPOSCTL 1632 QPOSCNT QPOSMAX QPOSINIT PIE EQEPxINT Enhanced QEP (eQEP) peripheral System control registers QCTMR QCPRD 1616 QCAPCTL EQEPxENCLK SYSCLK Data bus T o CPU QMA Figure 6-57. eQEP Block Diagram TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
168 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.15.5.1 eQEP Electrical Data and Timing For an explanation of the input qualifier parameters, see the General-Purpose Input Timing Requirements table. 6.15.5.1.1 eQEP Timing Requirements MIN MAX UNIT tw(QEPP) QEP input period Synchronous(1) 2tc(SYSCLK) cycles Synchronous with input qualifier 2[1tc(SYSCLK) + tw(IQSW)] tw(INDEXH) QEP Index Input High time Synchronous(1) 2tc(SYSCLK) cycles Synchronous with input qualifier 2tc(SYSCLK) + tw(IQSW) tw(INDEXL) QEP Index Input Low time Synchronous(1) 2tc(SYSCLK) cycles Synchronous with input qualifier 2tc(SYSCLK) + tw(IQSW) tw(STROBH) QEP Strobe High time Synchronous(1) 2tc(SYSCLK) cycles Synchronous with input qualifier 2tc(SYSCLK) + tw(IQSW) tw(STROBL) QEP Strobe Input Low time Synchronous(1) 2tc(SYSCLK) cycles Synchronous with input qualifier 2tc(SYSCLK) + tw(IQSW) (1) The GPIO GPxQSELn Asynchronous mode should not be used for eQEP module input pins. 6.15.5.1.2 eQEP Switching Characteristics over recommended operating conditions (unless otherwise noted) PARAMETER MIN MAX UNIT td(CNTR)xin Delay time, external clock to counter increment 5tc(SYSCLK) cycles td(PCS-OUT)QEP Delay time, QEP input edge to position compare sync output 7tc(SYSCLK) cycles www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 169 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.16 Communications Peripherals
6.16.1 Modular Controller Area Network (MCAN)
The Controller Area Network (CAN) is a serial communications protocol that efficiently supports distributed real-time control with a high level of reliability. CAN has high immunity to electrical interference and the ability to detect various type of errors. In CAN, many short messages are broadcast to the entire network, which provides data consistency in every node of the system. The MCAN module supports both classic CAN and CAN FD (CAN with flexible data-rate) protocols. The CAN FD feature allows higher throughput and increased payload per data frame. Classic CAN and CAN FD devices may coexist on the same network without any conflict provided that partial network transceivers, which can detect and ignore CAN FD without generating bus errors, are used by the classic CAN devices. The MCAN module is compliant to ISO 11898-1:2015. Note The availability of the CAN FD feature is dependent on the device's part number. Refer to the device data sheet for more information. MCANSS Uncorrectable ECC Correctable ECC Configurable Interrupts (2 lines) Counter Overflow and Clock Stop/ Wakeup Peripheral Clock Bit Timing Clock Reset Clock disable/ enable SYSCLK MCAN Bit Clock Clock Stop and Wakeup NMI mcanss_tx mcanss_rx Device CPU BUS Wakeup RESET PIE Figure 6-58. MCAN Module Overview The MCAN module implements the following features:
- Conforms with CAN Protocol 2.0 A, B and ISO 11898-1:2015
- Full CAN FD support (up to 64 data bytes)
- AUTOSAR and SAE J1939 support
- Flexible Message RAM allocation (maximum configuration below is for a device with 4352 32-bit word message RAM) – Up to 32 dedicated transmit buffers – Configurable transmit FIFO, up to 32 elements – Configurable transmit queue, up to 32 elements – Configurable transmit Event FIFO, up to 32 elements – Up to 64 dedicated receive buffers – Two configurable receive FIFOs, up to 64 elements each – Up to 128 filter elements
- Loop-back mode for self-test TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
170 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
- Maskable interrupt (two configurable interrupt lines, correctable ECC, counter overflow and clock stop/ wakeup)
- Non-maskable interrupt (uncorrectable ECC)
- Two clock domains (CAN clock/host clock)
- ECC check for Message RAM
- Clock stop and wake-up support
- Timestamp counter Non-supported features:
- Host bus firewall
- Clock calibration
- Debug over CAN www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 171 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.16.2 Inter-Integrated Circuit (I2C)
The I2C module has the following features:
- Compliance with the NXP Semiconductors I2C-bus specification (version 2.1): – Support for 8-bit format transfers – 7-bit and 10-bit addressing modes – General call – START byte mode – Support for multiple controller-transmitters and target-receivers – Support for multiple target-transmitters and controller-receivers – Combined controller transmit/receive and receive/transmit mode – Data transfer rate from 10Kbps up to 400Kbps (Fast-mode)
- Supports voltage thresholds compatible to: – SMBus 3.0 and below – PMBus 1.3 and below
- One 16-byte receive FIFO and one 16-byte transmit FIFO
- Supports two ePIE interrupts – I2Cx interrupt – Any of the below conditions can be configured to generate an I2Cx interrupt:
- Transmit Ready
- Receive Ready
- Register-Access Ready
- No-Acknowledgment
- Arbitration-Lost
- Stop Condition Detected
- Addressed-as-Target – I2Cx_FIFO interrupts:
- Transmit FIFO interrupt
- Receive FIFO interrupt
- Module enable and disable capability
- Free data format mode Figure 6-59 shows how the I2C peripheral module interfaces within the device. TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
172 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Figure 6-59. I2C Peripheral Module Interfaces www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 173 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.16.2.1 I2C Electrical Data and Timing
To meet all of the I2C protocol timing specifications, the I2C module clock must be configured in the range from 7 MHz to 12 MHz. A pullup resistor must be chosen to meet the I2C standard timings. In most circumstances, 2.2 k Ω of total bus resistance to VDDIO is sufficient. For evaluating pullup resistor values for a particular design, see the I2C Bus Pullup Resistor Calculation Application Report.
6.16.2.1.1 I2C Timing Requirements
NO. MIN MAX UNIT Standard mode T0 fmod I2C module frequency 7 12 MHz T1 th(SDA-SCL)START Hold time, START condition, SCL fall delay after SDA fall 4.0 µs T2 tsu(SCL-SDA)START Setup time, Repeated START, SCL rise before SDA fall delay 4.0 µs T3 th(SCL-DAT) Hold time, data after SCL fall 0 µs T4 tsu(DAT-SCL) Setup time, data before SCL rise 250 ns T5 tr(SDA) Rise time, SDA 1000 ns T6 tr(SCL) Rise time, SCL 1000 ns T7 tf(SDA) Fall time, SDA 300 ns T8 tf(SCL) Fall time, SCL 300 ns T9 tsu(SCL-SDA)STOP Setup time, STOP condition, SCL rise before SDA rise delay 4.0 µs T10 tw(SP) Pulse duration of spikes that will be suppressed by filter 0 50 ns T11 Cb capacitance load on each bus line 400 pF Fast mode T0 fmod I2C module frequency 7 12 MHz T1 th(SDA-SCL)START Hold time, START condition, SCL fall delay after SDA fall 0.6 µs T2 tsu(SCL-SDA)START Setup time, Repeated START, SCL rise before SDA fall delay 0.6 µs T3 th(SCL-DAT) Hold time, data after SCL fall 0 µs T4 tsu(DAT-SCL) Setup time, data before SCL rise 100 ns T5 tr(SDA) Rise time, SDA 20 300 ns T6 tr(SCL) Rise time, SCL 20 300 ns T7 tf(SDA) Fall time, SDA 11.4 300 ns T8 tf(SCL) Fall time, SCL 11.4 300 ns T9 tsu(SCL-SDA)STOP Setup time, STOP condition, SCL rise before SDA rise delay 0.6 µs T10 tw(SP) Pulse duration of spikes that will be suppressed by filter 0 50 ns T11 Cb capacitance load on each bus line 400 pF TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
174 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.16.2.1.2 I2C Switching Characteristics
over recommended operating conditions (unless otherwise noted) NO. PARAMETER TEST CONDITIONS MIN MAX UNIT Standard mode S1 fSCL SCL clock frequency 0 100 kHz S2 TSCL SCL clock period 10 µs S3 tw(SCLL) Pulse duration, SCL clock low 4.7 µs S4 tw(SCLH) Pulse duration, SCL clock high 4.0 µs S5 tBUF Bus free time between STOP and START conditions 4.7 µs S6 tv(SCL-DAT) Valid time, data after SCL fall 3.45 µs S7 tv(SCL-ACK) Valid time, Acknowledge after SCL fall 3.45 µs S8 II Input current on pins 0.1 Vbus < Vi < 0.9 Vbus –10 10 µA Fast mode S1 fSCL SCL clock frequency 0 400 kHz S2 TSCL SCL clock period 2.5 µs S3 tw(SCLL) Pulse duration, SCL clock low 1.3 µs S4 tw(SCLH) Pulse duration, SCL clock high 0.6 µs S5 tBUF Bus free time between STOP and START conditions 1.3 µs S6 tv(SCL-DAT) Valid time, data after SCL fall 0.9 µs S7 tv(SCL-ACK) Valid time, Acknowledge after SCL fall 0.9 µs S8 II Input current on pins 0.1 Vbus < Vi < 0.9 Vbus –10 10 µA
6.16.2.1.3 I2C Timing Diagram
Contd... Contd... Repeated START 9th clock STOP ACK ACK Figure 6-60. I2C Timing Diagram www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 175 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.16.3 Power Management Bus (PMBus) Interface
The PMBus module has the following features:
- Compliance with the SMI Forum PMBus Specification (Part I v1.0 and Part II v1.1)
- Supports voltage thresholds compatible to: – PMBus 1.3and below – SMBus 3.0and below
- Support for controller and target
- Support for I2C mode
- Support for threespeeds: – Standard Mode: Up to 100 kHz – Fast Mode: 400 kHz – Fast Plus Mode: 1MHz
- Packet error checking
- CONTROL and ALERT signals
- Clock high and low time-outs
- Four-byte transmit and receive buffers
- One maskable interrupt, which can be generated by several conditions: – Receive data ready – Transmit buffer empty – Target address received – End of message – ALERT input asserted – Clock low time-out – Clock high time-out – Bus free Note Please see the TMS320F28P55x Real-Time Microcontrollers Technical Reference Manual to determine which pins support Fast Plus Mode as well as full SMBUS3.0 and PMBUS1.3 specifications PMBus Module GPIO Mux ALERT CTL SCL SDA SYSCLK PCLKCR20 Div Bit clock PIEPMBUSA_INT CPU PMBCTRL Other registers DMA PMBTXBUF PMBRXBUFShift register Figure 6-61. PMBus Block Diagram TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
176 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.16.3.1 PMBus Electrical Data and Timing
6.16.3.1.1 PMBus Electrical Characteristics
over recommended operating conditions (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT VIL Valid low-level input voltage 0.8 V VIH Valid high-level input voltage 2.1 VDDIO V VOL Low-level output voltage At Ipullup = 4 mA 0.4 V IOL Low-level output current VOL ≤ 0.4 V 4 mA tSP Pulse width of spikes that must be suppressed by the input filter 0 50 ns Ii Input leakage current on each pin 0.1 Vbus < Vi < 0.9 Vbus –10 10 µA Ci Capacitance on each pin 10 pF
6.16.3.1.2 PMBus Fast Plus Mode Switching Characteristics
over recommended operating conditions (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT Fmod PMBus Module Clock Frequency(2) 20 25 MHz fSCL SCL clock frequency 3.3V Nominal Bus Voltage 10 1000(3) kHz 5.0V Nominal Bus Voltage 10 1000(4) kHz tBUF Bus free time between STOP and START conditions 0.5 µs tHD;STA START condition hold time -- SDA fall to SCL fall delay 0.26 µs tSU;STA Repeated START setup time -- SCL rise to SDA fall delay 0.26 µs tSU;STO STOP condition setup time -- SCL rise to SDA rise delay 0.26 µs tHD;DAT Data hold time after SCL fall 300 ns Data hold time after SCL fall PMBCTRL_ZH_EN = 1 (1) 0 ns tSU;DAT Data setup time before SCL rise 50 ns tTimeout Clock low time-out 25 35 ms tLOW Low period of the SCL clock 0.5 µs tHIGH High period of the SCL clock 0.26 50 µs tLOW;SEXT Cumulative clock low extend time (target device) From START to STOP 25 ms tLOW;MEXT Cumulative clock low extend time (controller device) Within each byte 10 ms tr Rise time of SDA and SCL 5% to 95% 20 120 ns tf Fall time of SDA and SCL 95% to 5% 20 120 ns (1) This bit must be set to enable 0ns hold time/SMBUS3.0 Compliance (2) If the max clock is used all below timings will be met with the default register configurations for the PMBUS (3) Due to max IO drive strength of 12mA, 1MHz SCL clock is only valid for bus capacitances up to 520pF (4) Due to max IO drive strength of 12mA, 1MHz SCL clock is only valid for bus capacitances up to 330pF www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 177 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.16.3.1.3 PMBus Fast Mode Switching Characteristics
over recommended operating conditions (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT Fmod PMBus Module Clock Frequency (2) f(SYSCLK) / 32
10 MHz
fSCL SCL clock frequency 10 400 kHz tBUF Bus free time between STOP and START conditions 1.3 µs tHD;STA START condition hold time -- SDA fall to SCL fall delay 0.6 µs tSU;STA Repeated START setup time -- SCL rise to SDA fall delay 0.6 µs tSU;STO STOP condition setup time -- SCL rise to SDA rise delay 0.6 µs tHD;DAT Data hold time after SCL fall 300 ns Data hold time after SCL fall PMBCTRL_INC_1[ZH+EN] = 1(1) 0 ns tSU;DAT Data setup time before SCL rise 100 ns tTimeout Clock low time-out 25 35 ms tLOW Low period of the SCL clock 1.3 µs tHIGH High period of the SCL clock 0.6 50 µs tLOW;SEXT Cumulative clock low extend time (target device) From START to STOP 25 ms tLOW;MEXT Cumulative clock low extend time (controller device) Within each byte 10 ms tr Rise time of SDA and SCL 5% to 95% 20 300 ns tf Fall time of SDA and SCL 95% to 5% 20 300 ns (1) This bit must be set to enable 0ns hold time/SMBUS3.0 Compliance (2) If the max clock is used all below timings will be met with the default register configurations for the PMBUS TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
178 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.16.3.1.4 PMBus Standard Mode Switching Characteristics
over recommended operating conditions (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT Fmod PMBus Module Clock Frequency(2) f(SYSCLK) / 32 fSCL SCL clock frequency 10 100 kHz tBUF Bus free time between STOP and START conditions 4.7 µs tHD;STA START condition hold time -- SDA fall to SCL fall delay 4 µs tSU;STA Repeated START setup time -- SCL rise to SDA fall delay 4.7 µs tSU;STO STOP condition setup time -- SCL rise to SDA rise delay 4 µs tHD;DAT Data hold time after SCL fall 300 ns Data hold time after SCL fall PMBCTRL_INC_1[ZH+EN] = 1 (1) 0 ns tSU;DAT Data setup time before SCL rise 250 ns tTimeout Clock low time-out 25 35 ms tLOW Low period of the SCL clock 4.7 µs tHIGH High period of the SCL clock 4 50 µs tLOW;SEXT Cumulative clock low extend time (target device) From START to STOP 25 ms tLOW;MEXT Cumulative clock low extend time (controller device) Within each byte 10 ms tr Rise time of SDA and SCL 1000 ns tf Fall time of SDA and SCL 300 ns (1) This bit must be set to enable 0ns hold time/SMBUS3.0 Compliance (2) If the max clock is used all below timings will be met with the default register configurations for the PMBUS www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 179 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.16.4 Serial Communications Interface (SCI)
The SCI is a 2-wire asynchronous serial port, commonly known as a UART. The SCI module supports digital communications between the CPU and other asynchronous peripherals that use the standard non-return-to-zero (NRZ) format The SCI receiver and transmitter each have a 16-level-deep FIFO for reducing servicing overhead, and each has its own separate enable and interrupt bits. Both can be operated independently for half-duplex communication, or simultaneously for full-duplex communication. To specify data integrity, the SCI checks received data for break detection, parity, overrun, and framing errors. The bit rate is programmable to different speeds through a 16-bit baud-select register. Features of the SCI module include:
- Two external pins: – SCITXD: SCI transmit-output pin – SCIRXD: SCI receive-input pin – Baud rate programmable to 64K different rates
- Data-word format – 1 start bit – Data-word length programmable from 1 to 8 bits – Optional even/odd/no parity bit – 1 or 2 stop bits
- Four error-detection flags: parity, overrun, framing, and break detection
- Two wake-up multiprocessor modes: idle-line and address bit
- Half- or full-duplex operation
- Double-buffered receive and transmit functions
- Transmitter and receiver operations can be accomplished through interrupt-driven or polled algorithms with status flags. – Transmitter: TXRDY flag (transmitter-buffer register is ready to receive another character) and TX EMPTY flag (transmitter-shift register is empty) – Receiver: RXRDY flag (receiver-buffer register is ready to receive another character), BRKDT flag (break condition occurred), and RX ERROR flag (monitoring four interrupt conditions)
- Separate enable bits for transmitter and receiver interrupts (except BRKDT)
- NRZ format
- Auto baud-detect hardware logic
- 16-level transmit and receive FIFO Note All registers in this module are 8-bit registers. When a register is accessed, the register data is in the lower byte (bits 7–0), and the upper byte (bits 15–8) is read as zeros. Writing to the upper byte has no effect. Figure 6-62 shows the SCI block diagram. TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
180 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
TX FIFO_0 TX FIFO_1 TX FIFO_N Transmit Data Buffer Register SCITXBUF.7-0 TX FIFO Interrupts Baud Rate MSB/LSB Registers SCIHBAUD.15-8 SCILBAUD.7-0 LSPCLK Frame Format and Mode Parity SCICCR.6 SCICCR.5 Even/Odd Enable SCICTL1.3 TXWAKE WUT RXENA SCICTL2.6 TXEMPTY SCICTL2.7 TXRDY SCICTL2.0 TXINTENA TX Interrupt Logic 0 1 0 1 Auto Baud Detect Logic TXINT To CPU SCIRXD SCICTL1.0 SCI TX Interrupt Select Logic SCITXD SCICTL1.1 TXENA RX FIFO_0 RX FIFO_1 RX FIFO_N Receive Data Buffer Register SCIRXBUF.7-0 RXENA SCICTL1.0 RX FIFO Interrupts RXFFOVF SCIRXST.6 RXRDY SCIRXST.5 BRKDT SCICTL2.1 RXBKINTENA RX Interrupt Logic SCIRXST.7 RXERROR SCICTL1.6 RXERRINTENA SCI RX Interrupt Select Logic 0 1 0 1 SCIFFENA SCIFFTX.14 RXWAKE SCIRXST.1 RXINT To CPU BRKDT FE OE PE SCIRXST.5-2 SCIFFRX.15 RXSHF Register Figure 6-62. SCI Block Diagram www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 181 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.16.5 Serial Peripheral Interface (SPI)
The serial peripheral interface (SPI) is a high-speed synchronous serial input and output (I/O) port that allows a serial bit stream of programmed length (1 to 16 bits) to be shifted into and out of the device at a programmed bit- transfer rate. The SPI is normally used for communications between the MCU controller and external peripherals or another controller. Typical applications include external I/O or peripheral expansion through devices such as shift registers, display drivers, and analog-to-digital converters (ADCs). Multidevice communications are supported by the controller or peripheral operation of the SPI. The port supports a 16-level, receive and transmit FIFO for reducing CPU servicing overhead. The SPI module features include:
- SPIPOCI: SPI peripheral-output/controller-input pin
- SPIPICO: SPI peripheral-input/controller-output pin
- SPIPTE: SPI peripheral transmit-enable pin
- SPICLK: SPI serial-clock pin
- Two operational modes: Controller and Peripheral
- Baud rate: 125 different programmable rates. The maximum baud rate that can be employed is limited by the maximum speed of the I/O buffers used on the SPI pins.
- Data word length: 1 to 16 data bits
- Four clocking schemes (controlled by clock polarity and clock phase bits) include: – Falling edge without phase delay: SPICLK active-high. SPI transmits data on the falling edge of the SPICLK signal and receives data on the rising edge of the SPICLK signal. – Falling edge with phase delay: SPICLK active-high. SPI transmits data one half-cycle ahead of the falling edge of the SPICLK signal and receives data on the falling edge of the SPICLK signal. – Rising edge without phase delay: SPICLK inactive-low. SPI transmits data on the rising edge of the SPICLK signal and receives data on the falling edge of the SPICLK signal. – Rising edge with phase delay: SPICLK inactive-low. SPI transmits data one half-cycle ahead of the rising edge of the SPICLK signal and receives data on the rising edge of the SPICLK signal.
- Simultaneous receive and transmit operation (transmit function can be disabled in software)
- Transmitter and receiver operations are accomplished through either interrupt-driven or polled algorithm
- 16-level transmit/receive FIFO
- DMA support
- High-speed mode
- Delayed transmit control
- 3-wire SPI mode
- SPIPTE inversion for digital audio interface receive mode on devices with two SPI modules Figure 6-63 shows the SPI CPU interfaces. TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
182 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Figure 6-63. SPI CPU Interface www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 183 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.16.5.1 SPI Controller Mode Timings
The following section contains the SPI Controller Mode Timings. Note All timing parameters for SPI High-Speed Mode assume a load capacitance of 5 pF on SPICLK, SPIPICO, and SPIPOCI.
6.16.5.1.1 SPI Controller Mode Timing Requirements
NO. PARAMETER (2) (BRR + 1)(1) MIN MAX UNIT High-Speed Mode 8 tsu(POCI)M Setup time, SPIPOCI valid before SPICLK Even, Odd 0.7 ns 8 tsu(POCI)M Setup time, SPIPOCI valid before SPICLK(when used on pin muxed with PMBUS - GPIO2, 3, 9, or 32) Even, Odd 1.5 ns 8 tsu(POCI)M Setup time, SPIPOCI valid before SPICLK(when used on pin muxed with USB - GPIO23, or 41) Even, Odd 1.5 ns 9 th(POCI)M Hold time, SPIPOCI valid after SPICLK Even, Odd 6.5 ns Normal Mode 8 tsu(POCI)M Setup time, SPIPOCI valid before SPICLK Even, Odd 15 ns 8 tsu(POCI)M Setup time, SPIPOCI valid before SPICLK(when used on pin muxed with PMBUS - GPIO2, 3, 9, or 32) Even, Odd 16.5 ns 9 th(POCI)M Hold time, SPIPOCI valid after SPICLK Even, Odd 0 ns (1) The (BRR + 1) condition is Even when (SPIBRR + 1) is even or SPIBRR is 0 or 2. It is Odd when (SPIBRR + 1) is odd and SPIBRR is greater than 3. (2) GPIOs 2, 3, 9, 23, 32, or 41 do not support full High-Speed Mode(37.5MHz) SPI operation TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
184 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.16.5.1.2 SPI Controller Mode Switching Characteristics - Clock Phase 0
over recommended operating conditions (unless otherwise noted) NO. PARAMETER (1) (2) (4) (BRR + 1)(3) MIN MAX UNIT General 1 tc(SPC)M Cycle time, SPICLK Even 4tc(LSPCLK) 128tc(LSPCLK) ns Odd 5tc(LSPCLK) 127tc(LSPCLK) 2 tw(SPC1)M Pulse duration, SPICLK, first pulse Even 0.5tc(SPC)M – 1 0.5tc(SPC)M + 1 ns Odd 0.5tc(SPC)M + 0.5tc(LSPCLK) – 1 0.5tc(SPC)M + 0.5tc(LSPCLK) + 1 3 tw(SPC2)M Pulse duration, SPICLK, second pulse Even 0.5tc(SPC)M – 1 0.5tc(SPC)M + 1 ns Odd 0.5tc(SPC)M – 0.5tc(LSPCLK) – 1 0.5tc(SPC)M – 0.5tc(LSPCLK) + 1 23 td(SPC)M Delay time, SPIPTE active to SPICLK Even 1.5tc(SPC)M – 3tc(SYSCLK) – 3 1.5tc(SPC)M – 3tc(SYSCLK) + 3 ns Odd 1.5tc(SPC)M – 4tc(SYSCLK) – 3 1.5tc(SPC)M – 4tc(SYSCLK) + 3 23 td(SPC)M Delay time, SPIPTE active to SPICLK(when used on pin muxed with PMBUS - GPIO2, 3, 9, or 32) Even 1.5tc(SPC)M – 3tc(SYSCLK) – 4 1.5tc(SPC)M – 3tc(SYSCLK) + 3 ns Odd 1.5tc(SPC)M – 4tc(SYSCLK) – 4 1.5tc(SPC)M – 4tc(SYSCLK) + 3 23 td(SPC)M Delay time, SPIPTE active to SPICLK(when used on pin muxed with USB - GPIO23 or GPIO41) Even 1.5tc(SPC)M – 3tc(SYSCLK) – 3 1.5tc(SPC)M – 3tc(SYSCLK) + 5.5 ns Odd 1.5tc(SPC)M – 4tc(SYSCLK) – 3 1.5tc(SPC)M – 4tc(SYSCLK) + 5.5 24 tv(STE)M Valid time, SPICLK to SPIPTE inactive Even 0.5tc(SPC)M – 3 0.5tc(SPC)M + 3 ns Odd 0.5tc(SPC)M – 0.5tc(LSPCLK) – 3 0.5tc(SPC)M – 0.5tc(LSPCLK) + 3 24 tv(STE)M Valid time, SPICLK to SPIPTE inactive(when used on pin muxed with PMBUS - GPIO2, 3, 9, or 32) Even 0.5tc(SPC)M – 4 0.5tc(SPC)M + 3 ns Odd 0.5tc(SPC)M – 0.5tc(LSPCLK) – 4 0.5tc(SPC)M – 0.5tc(LSPCLK) + 3 24 tv(STE)M Valid time, SPICLK to SPIPTE inactive(when used on pin muxed with USB - GPIO23 or GPIO41) Even 0.5tc(SPC)M – 3 0.5tc(SPC)M + 5.5 ns Odd 0.5tc(SPC)M – 0.5tc(LSPCLK) – 3 0.5tc(SPC)M – 0.5tc(LSPCLK) + 5.5 High-Speed Mode 4 td(PICO)M Delay time, SPICLK to SPIPICO valid Even, Odd 1 ns 4 td(PICO)M Delay time, SPICLK to SPIPICO valid(when used on pin muxed with PMBUS - GPIO2, 3, 9, or 32) Even, Odd 2 ns 5 tv(PICO)M Valid time, SPIPICO valid after SPICLK Even 0.5tc(SPC)M – 3 ns Odd 0.5tc(SPC)M – 0.5tc(LSPCLK) – 3 5 tv(PICO)M Valid time, SPIPICO valid after SPICLK(when used on pin muxed with PMBUS - GPIO2, 3, 9, or 32) Even 0.5tc(SPC)M – 4.5 ns Odd 0.5tc(SPC)M – 0.5tc(LSPCLK) – 4.5 Normal Mode 4 td(PICO)M Delay time, SPICLK to SPIPICO valid Even, Odd 2 ns 5 tv(PICO)M Valid time, SPIPICO valid after SPICLK Even 0.5tc(SPC)M – 3 ns Odd 0.5tc(SPC)M – 0.5tc(LSPCLK) – 3 www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 185 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.16.5.1.2 SPI Controller Mode Switching Characteristics - Clock Phase 0 (continued)
over recommended operating conditions (unless otherwise noted) NO. PARAMETER (1) (2) (4) (BRR + 1)(3) MIN MAX UNIT 5 tv(PICO)M Valid time, SPIPICO valid after SPICLK(when used on pin muxed with PMBUS - GPIO2, 3, 9, or 32) Even 0.5tc(SPC)M – 4.5 ns Odd 0.5tc(SPC)M – 0.5tc(LSPCLK) – 4.5 (1) 10-pF load on pin for High-Speed Mode. (2) 20-pF load on pin for Normal Mode. (3) The (BRR + 1) condition is Even when (SPIBRR + 1) is even or SPIBRR is 0 or 2. It is Odd when (SPIBRR + 1) is odd and SPIBRR is greater than 3. (4) GPIOs 2, 3, 9, 23, 32, or 41 do not support full High-Speed Mode(37.5MHz) SPI operation TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
186 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.16.5.1.3 SPI Controller Mode Switching Characteristics - Clock Phase 1
over recommended operating conditions (unless otherwise noted) NO. PARAMETER(1) (2) (4) (BRR + 1) (3) MIN MAX UNIT General 1 tc(SPC)M Cycle time, SPICLK Even 4tc(LSPCLK) 128tc(LSPCLK) ns Odd 5tc(LSPCLK) 127tc(LSPCLK) 2 tw(SPCH)M Pulse duration, SPICLK, first pulse Even 0.5tc(SPC)M – 1 0.5tc(SPC)M + 1 ns Odd 0.5tc(SPC)M – 0.5tc(LSPCLK) – 1 0.5tc(SPC)M – 0.5tc(LSPCLK) + 1 3 tw(SPC2)M Pulse duration, SPICLK, second pulse Even 0.5tc(SPC)M – 1 0.5tc(SPC)M + 1 ns Odd 0.5tc(SPC)M + 0.5tc(LSPCLK) – 1 0.5tc(SPC)M + 0.5tc(LSPCLK) + 1 23 td(SPC)M Delay time, SPIPTE valid to SPICLK Even, Odd 2tc(SPC)M – 3tc(SYSCLK) – 3 2tc(SPC)M – 3tc(SYSCLK) + 3 ns 23 td(SPC)M Delay time, SPIPTE valid to SPICLK(when used on pin muxed with PMBUS - GPIO2, 3, 9, or 32) Even, Odd 2tc(SPC)M – 3tc(SYSCLK) – 4 2tc(SPC)M – 3tc(SYSCLK) + 3 ns 23 td(SPC)M Delay time, SPIPTE valid to SPICLK(when used on pin muxed with USB - GPIO23 or GPIO41) Even, Odd 2tc(SPC)M – 3tc(SYSCLK) – 3 2tc(SPC)M – 3tc(SYSCLK) + 5.5 ns 24 td(STE)M Delay time, SPICLK to SPIPTE invalid Even –3 3 ns Odd –3 3 24 td(STE)M Delay time, SPICLK to SPIPTE invalid(when used on pin muxed with PMBUS - GPIO2, 3, 9, or 32) Even -4 3 ns Odd -4 3 24 td(STE)M Delay time, SPICLK to SPIPTE invalid(when used on pin muxed with USB - GPIO23 or GPIO41) Even –3 5.5 ns Odd –3 5.5 High-Speed Mode 4 td(PICO)M Delay time, SPIPICO valid to SPICLK Even 0.5tc(SPC)M – 2 ns Odd 0.5tc(SPC)M + 0.5tc(LSPCLK) – 2 4 td(PICO)M Delay time, SPIPICO valid to SPICLK (when used on pin muxed with PMBUS - GPIO2, 3, 9, or 32) Even 0.5tc(SPC)M – 3 ns Odd 0.5tc(SPC)M + 0.5tc(LSPCLK) – 3 5 tv(PICO)M Valid time, SPIPICO valid after SPICLK Even 0.5tc(SPC)M – 3 ns Odd 0.5tc(SPC)M – 0.5tc(LSPCLK) – 3 5 tv(PICO)M Valid time, SPIPICO valid after SPICLK (when used on pin muxed with PMBUS - GPIO2, 3, 9, or 32) Even 0.5tc(SPC)M – 4.5 ns Odd 0.5tc(SPC)M – 0.5tc(LSPCLK) – 4.5 Normal Mode 4 td(PICO)M Delay time, SPIPICO valid to SPICLK Even 0.5tc(SPC)M – 2 ns Odd 0.5tc(SPC)M + 0.5tc(LSPCLK) – 2 5 tv(PICO)M Valid time, SPIPICO valid after SPICLK Even 0.5tc(SPC)M – 3 ns Odd 0.5tc(SPC)M – 0.5tc(LSPCLK) – 3 5 tv(PICO)M Valid time, SPIPICO valid after SPICLK (when used on pin muxed with PMBUS - GPIO2, 3, 9, or 32) Even 0.5tc(SPC)M – 4.5 ns Odd 0.5tc(SPC)M – 0.5tc(LSPCLK) – 4.5 (1) 10-pF load on pin for High-Speed Mode. (2) 20-pF load on pin for Normal Mode. (3) The (BRR + 1) condition is Even when (SPIBRR + 1) is even or SPIBRR is 0 or 2. It is Odd when (SPIBRR + 1) is odd and SPIBRR is greater than 3. (4) GPIOs 2, 3, 9, 23, 32, or 41 do not support full High-Speed Mode(37.5MHz) SPI operation www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 187 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.16.5.1.4 SPI Controller Mode Timing Diagrams
(clock polarity = 0) SPICLK (clock polarity = 1) SPIPICO SPIPOCI SPIPTE Controller out data is valid Controller out data must be valid 23 24 A. On the trailing end of the word, SPIPTE will go inactive except between back-to-back transmit words in both FIFO and non-FIFO modes. Figure 6-64. SPI Controller Mode External Timing (Clock Phase = 0) SPICLK (clock polarity = 0) SPICLK (clock polarity = 1) SPIPICO SPIPOCI SPIPTE Controller out data is valid Controller out data must be valid 23 24 A. On the trailing end of the word, SPIPTE will go inactive except between back-to-back transmit words in both FIFO and non-FIFO modes. Figure 6-65. SPI Controller Mode External Timing (Clock Phase = 1) TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
188 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.16.5.2 SPI Peripheral Mode Timings
The following section contains the SPI Peripheral Mode Timings.
6.16.5.2.1 SPI Peripheral Mode Timing Requirements
NO. MIN MAX UNIT 12 tc(SPC)S Cycle time, SPICLK 4tc(SYSCLK) ns 13 tw(SPC1)S Pulse duration, SPICLK, first pulse 2tc(SYSCLK) – 1 ns 14 tw(SPC2)S Pulse duration, SPICLK, second pulse 2tc(SYSCLK) – 1 ns 19 tsu(PICO)S Setup time, SPIPICO valid before SPICLK 1.5tc(SYSCLK) ns 20 th(PICO)S Hold time, SPIPICO valid after SPICLK 1.5tc(SYSCLK) ns 25 tsu(STE)S Setup time, SPIPTE valid before SPICLK (Clock Phase = 0) 2tc(SYSCLK) + 15 ns Setup time, SPIPTE valid before SPICLK (Clock Phase = 1) 2tc(SYSCLK) + 15 ns 26 th(STE)S Hold time, SPIPTE invalid after SPICLK 1.5tc(SYSCLK) ns
6.16.5.2.2 SPI Peripheral Mode Switching Characteristics
over recommended operating conditions (unless otherwise noted) NO. PARAMETER(1) MIN MAX UNIT 15 td(POCI)S Delay time, SPICLK to SPIPOCI valid (non-high speed mode) 17 ns 15 td(POCI)S Delay time, SPICLK to SPIPOCI valid (high-speed mode) 12.5 ns Delay time, SPICLK to SPIPOCI valid (high-speed mode)(when used on pins muxed with PMBUS - GPIO2, 3, 9, or 32) 14 ns Delay time, SPICLK to SPIPOCI valid (high-speed mode)(when used on pins muxed with USB - GPIO23 or 41) 16.7 ns 16 tv(POCI)S Valid time, SPIPOCI valid after SPICLK 0 ns (1) 20-pF load on pin. www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 189 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.16.5.2.3 SPI Peripheral Mode Timing Diagrams
(clock polarity = 0) SPICLK (clock polarity = 1) SPIPOCI SPIPICO SPIPTE SPIPOCI data is valid SPIPICO data must be valid 15 16 25 26 Figure 6-66. SPI Peripheral Mode External Timing (Clock Phase = 0) SPICLK (clock polarity = 0) SPICLK (clock polarity = 1) SPIPOCI SPIPICO SPIPOCI data is valid SPIPTE SPIPICO data must be valid Data valid Data valid 13 14 19 16 25 26 Figure 6-67. SPI Peripheral Mode External Timing (Clock Phase = 1) TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
190 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.16.6 Local Interconnect Network (LIN)
This device contains one Local Interconnect Network (LIN) module. The LIN module adheres to the LIN 2.1 standard as defined by the LIN Specification Package Revision 2.1 . The LIN is a low-cost serial interface designed for applications where the CAN protocol may be too expensive to implement, such as small subnetworks for cabin comfort functions like interior lighting or window control in an automotive application. The LIN standard is based on the SCI (UART) serial data link format. The communication concept is single- commander and multiple- responder with a message identification for multicast transmission between any network nodes. The LIN module can be programmed to work either as an SCI or as a LIN as the core of the module is an SCI. The hardware features of the SCI are augmented to achieve LIN compatibility. The SCI module is a universal asynchronous receiver-transmitter (UART) that implements the standard non-return-to-zero format. Though the registers are common for LIN and SCI, the register descriptions have notes to identify the register/bit usage in different modes. Because of this, code written for this module cannot be directly ported to the stand- alone SCI module and vice versa. The LIN module has the following features:
- Compatibility with LIN 1.3, 2.0 and 2.1 protocols
- Configurable baud rate up to 20 kbps (as per LIN 2.1 protocol)
- Two external pins: LINRX and LINTX
- Multibuffered receive and transmit units
- Identification masks for message filtering
- Automatic commander header generation – Programmable synchronization break field – Synchronization field – Identifier field
- Responder automatic synchronization – Synchronization break detection – Optional baud rate update – Synchronization validation
- 231 programmable transmission rates with 7 fractional bits
- Wakeup on LINRX dominant level from transceiver
- Automatic wake-up support – Wakeup signal generation – Expiration times on wakeup signals
- Automatic bus idle detection
- Error detection – Bit error – Bus error – No-response error – Checksum error – Synchronization field error – Parity error
- Capability to use direct memory access (DMA) for transmit and receive data
- Two interrupt lines with priority encoding for: – Receive – Transmit – ID, error, and status
- Support for LIN 2.0 checksum
- Enhanced synchronizer finite state machine (FSM) support for frame processing
- Enhanced handling of extended frames
- Enhanced baud rate generator www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 191 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
- Update wakeup/go to sleep INTERFACE CHECKSUM CALCULATOR TXRX ERROR DETECTOR (TED) BIT MONITOR ID PARTY CHECKER MASK FILTER TIME-OUT CONTROL COUNTER SYNCHRONIZER FSM COMPARE ADDRESS BUS READ DATA BUS WRITE DATA BUS
8 RECEIVE
8 TRANSMIT
Figure 6-68. LIN Block Diagram TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
192 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.16.7 Fast Serial Interface (FSI)
The Fast Serial Interface (FSI) module is a serial communication peripheral capable of reliable and robust high-speed communications. The FSI is designed to ensure data robustness across many system conditions such as chip-to-chip as well as board-to-board across an isolation barrier. Payload integrity checks such as CRC, start- and end-of-frame patterns, and user-defined tags, are encoded before transmit and then verified after receipt without additional CPU interaction. Line breaks can be detected using periodic transmissions, all managed and monitored by hardware. The FSI is also tightly integrated with other control peripherals on the device. To ensure that the latest sensor data or control parameters are available, frames can be transmitted on every control loop period. An integrated skew-compensation block has been added on the receiver to handle skew that may occur between the clock and data signals due to a variety of factors, including trace-length mismatch and skews induced by an isolation chip. With embedded data robustness checks, data-link integrity checks, skew compensation, and integration with control peripherals, the FSI can enable high-speed, robust communication in any system. These and many other features of the FSI follow. The FSI module includes the following features:
- Independent transmitter and receiver cores
- Source-synchronous transmission
- Dual data rate (DDR)
- One or two data lines
- Programmable data length
- Skew adjustment block to compensate for board and system delay mismatches
- Frame error detection
- Programmable frame tagging for message filtering
- Hardware ping to detect line breaks during communication (ping watchdog)
- Two interrupts per FSI core
- Externally triggered frame generation
- Hardware- or software-calculated CRC
- Embedded ECC computation module
- Register write protection
- DMA support
- SPI compatibility mode (limited features available) Operating the FSI at maximum speed (60 MHz) at dual data rate (120Mbps) may require the integrated skew compensation block to be configured according to the specific operating conditions on a case-by-case basis. The Fast Serial Interface (FSI) Skew Compensation Application Report provides example software on how to configure and set up the integrated skew compensation block on the Fast Serial Interface. The FSI consists of independent transmitter (FSITX) and receiver (FSIRX) cores. The FSITX and FSIRX cores are configured and operated independently. The features available on the FSITX and FSIRX are described in the FSI Transmitter section and the FSI Receiver section of the TMS320F28P55x Real-Time Microcontrollers Technical Reference Manual, respectively. www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 193 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.16.7.1 FSI Transmitter
The FSI transmitter module handles the framing of data, CRC generation, signal generation of TXCLK, TXD0, and TXD1, as well as interrupt generation. The operation of the transmitter core is controlled and configured through programmable control registers. The transmitter control registers let the CPU (or the CLA) program, control, and monitor the operation of the FSI transmitter. The transmit data buffer is accessible by the CPU, CLA, and the DMA. The transmitter has the following features:
- Automated ping frame generation
- Externally triggered ping frames
- Externally triggered data frames
- Software-configurable frame lengths
- 16-word data buffer
- Data buffer underrun and overrun detection
- Hardware-generated CRC on data bits
- Software ECC calculation on select data
- DMA support
- CLA task triggering Figure 6-69 shows the FSITX CPU interface. Figure 6-70 shows the high-level block diagram of the FSITX. Not all data paths and internal connections are shown. This diagram provides a high-level overview of the internal modules present in the FSITX. FSITX RegistersTrigger Muxes(A) DMA Register Interface C28x ePIE CLA GPIO MUX PCLKCR18 SYSRSN SYSCLK PLLRAWCLK FSITXyINT1 FSITXyINT2 FSITXyCLK FSITXyD0 FSITXyD1 FSITXyDMA A. The signals connected to the trigger muxes are described in the External Frame Trigger Mux section of the Fast Serial Interface (FSI) chapter in the TMS320F28P55x Real-Time Microcontrollers Technical Reference Manual. Figure 6-69. FSITX CPU Interface TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
194 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Control Registers, Interrupt Management Ping Time-out Counter Transmit Data Buffer ECC Logic Transmitter Core Register Interface External Frame Triggers PLLRAWCLK SYSRSN SYSCLK TXCLK TXD0 TXD1 Core Reset Transmit Clock Generator FSITXINT1 FSITXINT2 FSITX_DMA_EVT TXCLKIN FSITX FSI Mode: TXCLK = TXCLKIN/2 SPI Signaling Mode: TXCLK = TXCLKIN Figure 6-70. FSITX Block Diagram
6.16.7.1.1 FSITX Electrical Data and Timing
over operating free-air temperature range (unless otherwise noted) NO. PARAMETER(1) MIN MAX UNIT 1 tc(TXCLK) Cycle time, TXCLK 16.67 ns 1 tc(TXCLK) Cycle time, TXCLK(when any FSI signal is used on pins muxed with PMBUS - GPIO2, 3, 9, or 32) 26.67 ns 2 tw(TXCLK) Pulse width, TXCLK low or TXCLK high (0.5tc(TXCLK)) – 1 (0.5tc(TXCLK)) + 1 ns 3 td(TXCLK–TXD) Delay time, TXCLK rising or falling toTXD valid (0.25tc(TXCLK)) – 2 (0.25tc(TXCLK)) + 2 ns 3 td(TXCLK–TXD) Delay time, TXCLK rising or falling toTXD valid(when used on pin muxed with PMBUS - GPIO2, 3, 9, or 32) (0.25tc(TXCLK)) – 2 (0.25tc(TXCLK)) + 2.5 ns 4 td(TXCLK) TXCLK delay compensation at TX_DLYLINE_CTRL[TXCLK_DLY]=31 9.4 30 ns 5 td(TXD0) TXD0 delay compensation at TX_DLYLINE_CTRL[TXD0_DLY]=31 9.4 30 ns 6 td(TXD1) TXD1 delay compensation at TX_DLYLINE_CTRL[TXD1_DLY]=31 9.4 30 ns 7 td(DELAY_ELEMENT) Incremental delay of each delay line element for TXCLK, TXD0, and TXD1 0.29 1 ns (1) 10-pF load on pin. www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 195 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Figure 6-71. FSITX Timings TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
196 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.16.7.2 FSI Receiver
The receiver module interfaces to the FSI clock (RXCLK), and data lines (RXD0 and RXD1) after they pass through an optional programmable delay line. The receiver core handles the data framing, CRC computation, and frame-related error checking. The receiver bit clock and state machine are run by the RXCLK input, which is asynchronous to the device system clock. The receiver control registers let the CPU program (or the CLA), control, and monitor the operation of the FSIRX. The receive data buffer is accessible by the CPU, CLA, and the DMA. The receiver core has the following features:
- 16-word data buffer
- Multiple supported frame types
- Ping frame watchdog
- Frame watchdog
- CRC calculation and comparison in hardware
- ECC detection
- Programmable delay line control on incoming signals
- DMA support
- SPI compatibility mode
- CLA task triggering Figure 6-72 shows the FSIRX CPU interface. Figure 6-73 provides a high-level overview of the internal modules present in the FSIRX. Not all data paths and internal connections are shown. FSIRX Registers DMA Register Interface C28x ePIE CLA PCLKCR18 GPIO MUX FSIRXyINT2 FSIRXyINT1 FSIRXyDMA SYSRSN SYSCLK FSIRXyCLK FSIRXyD0 FSIRXyD1 Figure 6-72. FSIRX CPU Interface www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 197 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Control Registers, Interrupt Management Frame Watchdog Ping Watchdog Receive Data Buffer ECC Check Logic Receiver Core Register Interface Skew Control RXCLK RXD0 RXD1 Core Reset FSIRXINT1 FSIRXINT2 FSIRX_DMA_EVT SYSCLK SYSRSn FSIRX Figure 6-73. FSIRX Block Diagram
6.16.7.2.1 FSIRX Electrical Data and Timing
NO. MIN MAX UNIT 1 tc(RXCLK) Cycle time, RXCLK 16.67 ns 1 tc(RXCLK) Cycle time, RXCLK(when any FSI signal is used on pins muxed with PMBUS - GPIO2, 3, 9, or 32) 26.67 ns 2 tw(RXCLK) Pulse width, RXCLK low or RXCLK high. 0.35tc(RXCLK) 0.65tc(RXCLK) ns 3 tsu(RXCLK–RXD) Setup time with respect to RXCLK, applies to both edges of the clock 1.7 ns 3 tsu(RXCLK–RXD) Setup time with respect to RXCLK, applies to both edges of the clock(when used on pin muxed with PMBUS - GPIO2, 3, 9, or 32) 2.6 ns 4 th(RXCLK–RXD) Hold time with respect to RXCLK, applies to both edges of the clock 2 ns NO. PARAMETER(1) MIN MAX UNIT 1 td(RXCLK) RXCLK delay compensation at RX_DLYLINE_CTRL[RXCLK_DLY]=31 9.7 30 ns 2 td(RXD0) RXD0 delay compensation at RX_DLYLINE_CTRL[RXD0_DLY]=31 9.7 30 ns 3 td(RXD1) RXD1 delay compensation at RX_DLYLINE_CTRL[RXD1_DLY]=31 9.7 30 ns 4 td(DELAY_ELEMENT) Incremental delay of each delay line element for RXCLK, RXD0, and RXD1 0.29 1 ns TDM1 tskew(TDM_CLK-TDM_Dx ) Delay skew introduced between RXCLK- TDM_CLK delay and RXDx-TDM_Dx delays -3 3 ns TDM1 td(RXCLK-TDM_CLK ) Delay time, RXCLK input to TDM_CLK output 2 14.5 ns TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
198 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
NO. PARAMETER(1) MIN MAX UNIT TDM2 td(RXD0-TXD0) Delay time, RXD0 input to TXD0 output 2 14.5 ns TDM3 td(RXD1-TXD1) Delay time, RXD1 input to TXD1 output 2 14.5 ns (1) 10-pF load on pin. FSIRXCLK FSIRXD0 FSIRXD1 Figure 6-74. FSIRX Timings www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 199 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.16.7.3 FSI SPI Compatibility Mode
The FSI supports a SPI compatibility mode to enable communication with programmable SPI devices. In this mode, the FSI transmits its data in the same manner as a SPI in a single clock configuration mode. While the FSI is able to physically interface with a SPI in this mode, the external device must be able to encode and decode an FSI frame to communicate successfully. This is because the FSI transmits all SPI frame phases with the exception of the preamble and postamble. The FSI provides the same data validation and frame checking as if it was in standard FSI mode, allowing for more robust communication without consuming CPU cycles. The external SPI is required to send all relevant information and can access standard FSI features such as the ping frame watchdog on the FSIRX, frame tagging, or custom CRC values. The list of features of SPI compatibility mode follows:
- Data will transmit on rising edge and receive on falling edge of the clock.
- Only 16-bit word size is supported.
- TXD1 will be driven like an active-low chip-select signal. The signal will be low for the duration of the full frame transmission.
- No receiver chip-select input is required. RXD1 is not used. Data is shifted into the receiver on every active clock edge.
- No preamble or postamble clocks will be transmitted. All signals return to the idle state after the frame phase is finished.
- It is not possible to transmit in the SPI peripheral configuration because the FSI TXCLK cannot take an external clock source.
6.16.7.3.1 FSITX SPI Signaling Mode Electrical Data and Timing
Special timings are not required for the FSIRX in SPI signaling mode. FSIRX timings listed in the FSIRX Timing Requirements table are applicable in SPI compatibility mode. Setup and Hold times are only valid on the falling edge of FSIRXCLK because this is the active edge in SPI signaling mode. over operating free-air temperature range (unless otherwise noted) NO. PARAMETER(1) MIN MAX UNIT 1 tc(TXCLK) Cycle time, TXCLK 16.67 ns 1 tc(TXCLK) Cycle time, TXCLK(when any FSI signal is used on pins muxed with PMBUS - GPIO2, 3, 9, or 32) 26.67 ns 2 tw(TXCLK) Pulse width, TXCLK low or TXCLK high (0.5tc(TXCLK)) – 1 (0.5tc(TXCLK)) + 1 ns 3 td(TXCLKH–TXD0) Delay time, TXD0 valid after TXCLK high 3 ns 4 td(TXD1-TXCLK) Delay time, TXCLK high after TXD1 low tw(TXCLK) – 3 ns 5 td(TXCLK-TXD1) Delay time, TXD1 high after TXCLK low tw(TXCLK) ns (1) 10-pF load on pin FSITXCLK FSITXD1 FSITXD0 4 5 Figure 6-75. FSITX SPI Signaling Mode Timings TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
200 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.16.8 Universal Serial Bus (USB)
The USB controller operates as a full-speed or low-speed function controller during point-to-point communications with USB host or device functions. The USB module has the following features:
- USB 2.0 full-speed and low-speed operation
- Integrated PHY
- Three transfer types: control, interrupt, and bulk
- 32 endpoints – One dedicated control IN endpoint and one dedicated control OUT endpoint – 15 configurable IN endpoints and 15 configurable OUT endpoints
- 4KB of dedicated endpoint memory Figure 6-76 shows the USB block diagram. Packet Encode/Decode Endpoint Control EP0 –31 Control Transmit Receive Combine Endpoints Host Transaction Scheduler Packet Encode Packet Decode CRC Gen/Check FIFO RAM Controller Cycle Control Rx Buff Rx Buff Tx Buff Tx Buff CPU Interface Interrupt Control EP Reg. Decoder Common Regs Cycle Control FIFO Decoder Interrupts CPU BusUTM Synchronization Data Sync HNP/SRP Timers USB FS/LS PHY USB DataLines D+ andD- Figure 6-76. USB Block Diagram Note The accuracy of the on-chip zero-pin oscillator (see the INTOSC Characteristics section) will not meet the accuracy requirements of the USB protocol. An external clock source must be used for applications using USB. For applications using the USB boot mode, see the Boot ROM and Peripheral Booting section for clock frequency requirements.
6.16.8.1 USB Electrical Data and Timing
6.16.8.1.1 USB Input Ports DP and DM Timing Requirements
V(CM) Differential input common mode range 0.8 2.5 V Z(IN) Input impedance 300 kΩ VCRS Crossover voltage 1.3 2.0 V VIL Static SE input logic-low level 0.8 V VIH Static SE input logic-high level 2.0 V VDI Differential input voltage 0.2 V www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 201 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
6.16.8.1.2 USB Output Ports DP and DM Switching Characteristics
over recommended operating conditions (unless otherwise noted) PARAMETER TEST CONDITIONS MIN MAX UNIT VOH D+, D– single-ended USB 2.0 load conditions 2.8 3.6 V VOL D+, D– single-ended USB 2.0 load conditions 0 0.3 V Z(DRV) D+, D– impedance 28 44 Ω tr Rise time Full speed, differential, CL = 50 pF, 10%/90%, Rpu on D+ 4 20 ns tf Fall time Full speed, differential, CL = 50 pF, 10%/90%, Rpu on D+ 4 20 ns TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
202 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
7 Detailed Description
7.1 Overview
The TMS320F28P55x (F28P55x) is a member of the C2000™ real-time microcontroller family of scalable, ultra-low latency devices designed for efficiency in power electronics, including but not limited to: high power density, high switching frequencies, and supporting the use of GaN and SiC technologies. These include such applications as:
- Industrial motor drives
- Motor control – Traction inverter motor control – HVAC motor control – Mobile robot motor control
- Solar inverters – Central inverter – Micro inverter – String inverter
- Digital power
- Electrical vehicles and transportation
- EV charging infrastructure The real-time control subsystem is based on TI’s 32-bit C28x DSP core, which provides 150 MIPS of signal- processing performance in each core for floating- or fixed-point code running from either on-chip flash or SRAM. The C28x CPU is further boosted by the Trigonometric Math Unit (TMU) and VCRC (Cyclical Redundancy Check) extended instruction sets , speeding up common algorithms key to real-time control systems. Extended instruction sets enable IEEE double-precision 32-bit floating-point math. Finally, the Control Law Accelerator (CLA) enables an additional 150 MIPS per core of independent processing ability. To allow fast context switching from existing to new firmware, hardware enhancements for Live Firmware Update (LFU) have been added to F28P55x. High-performance analog blocks are tightly integrated with the processing and control units to provide optimal real-time signal chain performance. The Analog-to-Digital Converter (ADC) has been enhanced with up to 39 analog channels, 22 of which have general-purpose input/output (GPIO) capability. Implementation of oversampling is greatly simplified with hardware improvement. For safety-critical ADC conversions, a hardware redundancy checker has been added that provides the ability to compare ADC conversion results from multiple ADC modules for consistency without additional CPU cycles. Three Programmable Gain Amplifiers(PGAs) are present, supporting unity gain as well as up to 64x of non-inverting gain. Twenty-four frequency-independent PWMs, 16 with high-resolution capability, enable control of multiple power stages, from 3-phase inverters to advanced multilevel power topologies. The inclusion of the Configurable Logic Block (CLB) allows the user to add custom logic and potentially integrate FPGA-like functions into the C2000 real-time MCU. Industry-standard protocols like CAN FD and USB 2.0 are available on this device. The Fast Serial Interface (FSI) enables up to 200 Mbps of robust communications across an isolation boundary. Enhancements have been made to the PMBUS module to support Fast Plus mode. Want to learn more about features that make C2000 MCUs the right choice for your real-time control system? Check out The Essential Guide for Developing With C2000 ™ Real-Time Microcontrollers and visit the C2000™ real-time control MCUs page. www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 203 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
7.2 Functional Block Diagram
Figure 7-1 shows the CPU system and associated peripherals. C28x CPU (150 MHz) FPU32 TMU VCRC DIAGNOSTICS DCC MPOST ERAD JTAG/cJTAG M0-M1 RAM 4KB LS0-LS9 RAM 64KB GS0-GS3 RAM 64KB DMA (150 MHz) PF1 24x ePWM Channels (16Ch Hi-Res Capable) 2x eCAP 3x eQEP (CW/CCW Support) 4x CMPSS 1x Buffered DAC PF3 65x GPIO Data Input XBAR Output XBAR ePWM XBAR PF4 PF2 CLA to DMA MSG RAM DMA to CLA MSG RAM SYSTEM CONTROL CPU Timers XTAL INTOSC1, INTOSC2 PLL ePIE Windowed WD NMI WD SECURITY JTAG Lock Secure Boot CLB XBAR CLB Input XBAR CLB Output XBAR PF7 OTHERS EPG CPU CLA DMA Buses Legend 3x PGA PF8 3x SCI 2x I2C PF9 PF10 PF11 1x AES PF12 Boot ROM Secure ROM Flash Bank0 2x CAN FD 1x LIN 2x CLB LFU1x USB Secure Memories Shown in Red NNPU NNPU NNPU A. The internal DAC from one of the CMPSS modules can be configured as an output DAC. B. The LIN module can also be used as a SCI module. Figure 7-1. Functional Block Diagram TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
204 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
7.3 Memory
7.3.1 Memory Map
The Memory Map table describes the memory map. See the Memory Controller Module section of the System Control chapter in the TMS320F28P55x Real-Time Microcontrollers Technical Reference Manual. Table 7-1. Memory Map MEMORY SIZE (x16) START ADDRESS END ADDRESS CPU1.DMA ACCESS CPU1.CLA1 DATA ACCESS CPU1.CLA1 PROGRAM ACCESS ECC/ Parity SECURITY PART NUMBER M0 RAM 1024 0x0000_0000 0x0000_03FF - - - ECC - All M1 RAM 1024 0x0000_0400 0x0000_07FF - - - ECC - All PIE Vector Table 512 0x0000_0D00 0x0000_0EFF - - - Parity - All CLAtoCPU MSG RAM 128 0x0000_1480 0x0000_14FF - YES - Parity - All CPUtoCLA MSG RAM 128 0x0000_1500 0x0000_157F - YES - Parity - All CLAtoDMA MSG RAM 128 0x0000_1680 0x0000_16FF YES YES - Parity - All DMAtoCLA MSG RAM 128 0x0000_1700 0x0000_177F YES YES - Parity - All LS8 RAM - CLA Prog 8192 0x0000_4000 0x0000_5FFF - - YES Parity YES F28P559SJ9- Q1,F28P550SJ9,F28P 559SG9- Q1,F28P550SG9,F28P 550SG8,F28P559SG8- Q1, F28P559SJ6- Q1,F28P550SJ6 LS9 RAM - CLA Prog 8192 0x0000_6000 0x0000_7FFF - - YES Parity YES F28P559SJ9- Q1,F28P550SJ9,F28P 559SG9- Q1,F28P550SG9,F28P 550SG8,F28P559SG8- Q1, F28P559SJ6- Q1,F28P550SJ6 LS0 RAM 2048 0x0000_8000 0x0000_87FF - YES YES Parity YES All LS1 RAM 2048 0x0000_8800 0x0000_8FFF - YES YES Parity YES All LS2 RAM 2048 0x0000_9000 0x0000_97FF - YES YES Parity YES All LS3 RAM 2048 0x0000_9800 0x0000_9FFF - YES YES Parity YES All LS4 RAM 2048 0x0000_A000 0x0000_A7FF - YES YES Parity YES All LS5 RAM 2048 0x0000_A800 0x0000_AFFF - YES YES Parity YES All LS6 RAM 2048 0x0000_B000 0x0000_B7FF - YES YES Parity YES All LS7 RAM 2048 0x0000_B800 0x0000_BFFF - YES YES Parity YES All GS0 RAM 8192 0x0000_C000 0x0000_DFFF YES - - Parity - All GS1 RAM 8192 0x0000_E000 0x0000_FFFF YES - - Parity - All CLA Data ROM 4096 0x0000_F000 0x0000_FFFF - YES - Parity - F28P559SJ9- Q1,F28P550SJ9,F28P 559SG9- Q1,F28P550SG9,F28P 550SG8,F28P559SG8- Q1, F28P559SJ6- Q1,F28P550SJ6 GS2 RAM 8192 0x0001_0000 0x0001_1FFF YES - - Parity - F28P559SJ9- Q1,F28P550SJ9,F28P 559SJ2- Q1,F28P559SJ6- Q1,F28P550SJ6 GS3 RAM 8192 0x0001_2000 0x0001_3FFF YES - - Parity - F28P559SJ9- Q1,F28P550SJ9,F28P 559SJ2-Q1, F28P559SJ6- Q1,F28P550SJ6 LS8 RAM - CPU 8192 0x0001_4000 0x0001_5FFF - - - Parity YES F28P559SJ9- Q1,F28P550SJ9,F28P 559SG9- Q1,F28P550SG9,F28P 559SG8-Q1, F28P559SG2- Q1,F28P559SJ2-Q1, F28P550SG8, F28P559SJ6- Q1,F28P550SJ6 www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 205 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 7-1. Memory Map (continued) MEMORY SIZE (x16) START ADDRESS END ADDRESS CPU1.DMA ACCESS CPU1.CLA1 DATA ACCESS CPU1.CLA1 PROGRAM ACCESS ECC/ Parity SECURITY PART NUMBER LS9 RAM - CPU 8192 0x0001_6000 0x0001_7FFF - - - Parity YES F28P559SJ9- Q1,F28P550SJ9,F28P 559SG9- Q1,F28P550SG9,F28P 559SG8-Q1, F28P559SG2- Q1,F28P559SJ2-Q1, F28P550SG8, F28P559SJ6- Q1,F28P550SJ6 USB RAM 2048 0x0004_1000 0x0004_17FF YES - - - - F28P559SJ9- Q1,F28P550SJ9,F28P 559SG9- Q1,F28P550SG9, F28P559SJ6- Q1,F28P550SJ6 MCANA Message RAM (CPU Access mode) 2048 0x0005_8000 0x0005_87FF YES - - ECC - All MCANA Message RAM (Peripheral mode) 4096 0x0005_8000 0x0005_8FFF YES - - ECC - All MCANB Message RAM (Peripheral mode) 4096 0x0005_A000 0x0005_AFFF YES - - ECC - All MCANB Message RAM (CPU Access mode) 2048 0x0005_A000 0x0005_A7FF YES - - ECC - All TI OTP Bank 0 1536 0x0007_2000 0x0007_25FF - - - ECC - All UID_REGS 6 0x0007_2172 0x0007_2177 - - - ECC - All TI OTP Bank 1 1536 0x0007_3000 0x0007_35FF - - - ECC - F28P559SJ9- Q1,F28P550SJ9,F28P 559SJ2-Q1, F28P559SJ6- Q1,F28P550SJ6 TI OTP Bank 2 1536 0x0007_4000 0x0007_45FF - - - ECC - All TI OTP Bank 3 1536 0x0007_5000 0x0007_55FF - - - ECC - F28P559SJ9- Q1,F28P550SJ9,F28P 559SJ2-Q1, F28P559SJ6- Q1,F28P550SJ6 TI OTP Bank 4 1536 0x0007_6000 0x0007_65FF - - - ECC - F28P559SJ9-Q1, F28P550SJ9, F28P559SJ2-Q1, F28P559SJ6-Q1, F28P550SJ6, F28P559SG9-Q1, F28P550SG9 DCSM BANK0 Z1 OTP 512 0x0007_8000 0x0007_81FF - - - ECC YES All DCSM BANK0 Z2 OTP 512 0x0007_8200 0x0007_83FF - - - ECC YES All User OTP Bank 1 1024 0x0007_8800 0x0007_8BFF - - - ECC - F28P559SJ9- Q1,F28P550SJ9,F28P 559SJ2-Q1, F28P559SJ6- Q1,F28P550SJ6 User OTP Bank 2 1024 0x0007_9000 0x0007_93FF - - - ECC - All User OTP Bank 3 1024 0x0007_9800 0x0007_9BFF - - - ECC - F28P559SJ9- Q1,F28P550SJ9,F28P 559SJ2-Q1, F28P559SJ6- Q1,F28P550SJ6 User OTP Bank 4 1024 0x0007_A000 0x0007_A3FF - - - ECC - F28P559SG9-Q1, F28P550SG9 Flash Bank 0 131072 0x0008_0000 0x0009_FFFF - - - ECC YES All TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
206 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 7-1. Memory Map (continued) MEMORY SIZE (x16) START ADDRESS END ADDRESS CPU1.DMA ACCESS CPU1.CLA1 DATA ACCESS CPU1.CLA1 PROGRAM ACCESS ECC/ Parity SECURITY PART NUMBER Flash Bank 1 131072 0x000A_0000 0x000B_FFFF - - - ECC YES F28P559SJ9- Q1,F28P550SJ9,F28P 559SJ2-Q1, F28P559SJ6- Q1,F28P550SJ6 Flash Bank 2 131072 0x000C_0000 0x000D_FFFF - - - ECC YES All Flash Bank 3 131072 0x000E_0000 0x000F_FFFF - - - ECC YES F28P559SJ9- Q1,F28P550SJ9,F28P 559SJ2-Q1, F28P559SJ6- Q1,F28P550SJ6 Flash Bank 4 32768 0x0010_0000 0x0010_7FFF - - - ECC YES F28P559SJ9-Q1, F28P550SJ9,F28P559 SJ2-Q1, F28P559SJ6- Q1, F28P550SJ6, F28P559SG9-Q1, F28P550SG9 Z1-SecureBoot Functions 3072 0x003F_4000 0x003F_4BFF - - - Parity YES All Z1-Safe Functions 1536 0x003F_4C00 0x003F_51FF - - - Parity YES All Z2-Safe Functions 1536 0x003F_5600 0x003F_5BFF - - - Parity YES All CPU STL 9216 0x003F_5C00 0x003F_7FFF - - - Parity - All Boot ROM 32768 0x003F_8000 0x003F_FFFF - - - Parity - All PIE Vector Table Swap 512 0x0100_0900 0x0100_0AFF - - - Parity - All CLA Data ROM (CPU Mapped) 4096 0x0100_1000 0x0100_1FFF - - - Parity - F28P559SJ9- Q1,F28P550SJ9,F28P 559SG9- Q1,F28P550SG9,F28P 550SG8,F28P559SG8- Q1, F28P559SJ6- Q1,F28P550SJ6 TI OTP Bank 0 ECC 192 0x0107_0400 0x0107_04BF - - - - - All TI OTP Bank 1 ECC 192 0x0107_0600 0x0107_06BF - - - - - F28P559SJ9- Q1,F28P550SJ9,F28P 559SJ2-Q1, F28P559SJ6- Q1,F28P550SJ6 TI OTP Bank 2 ECC 192 0x0107_0800 0x0107_08BF - - - - - All TI OTP Bank 3 ECC 192 0x0107_0A00 0x0107_0ABF - - - - - F28P559SJ9- Q1,F28P550SJ9,F28P 559SJ2-Q1, F28P559SJ6- Q1,F28P550SJ6 TI OTP Bank 4 ECC 192 0x0107_0C00 0x0107_0CBF - - - - - F28P559SJ9-Q1, F28P550SJ9, F28P559SJ2-Q1, F28P559SJ6-Q1, F28P550SJ6, F28P559SG9-Q1, F28P550SG9
7.3.1.1 Dedicated RAM (Mx RAM)
The CPU subsystem has two dedicated ECC-capable RAM blocks: M0 and M1. These memories are small nonsecure blocks that are tightly coupled with the CPU (that is, only the CPU has access to them).
7.3.1.2 Local Shared RAM (LSx RAM)
Local shared RAMs (LSx RAMs) are accessible to the CPU and CLA. All LSx RAM blocks have parity. These memories are secure and have CPU access protection (CPU write/CPU fetch). www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 207 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
7.3.1.3 Global Shared RAM (GSx RAM)
Global shared RAMs (GSx RAMs) are accessible from the CPU and DMA. The CPU and DMA have full read and write access to these memories. All GSx RAM blocks have parity. The GSx RAMs have access protection (CPU write/CPU fetch/DMA write/HIC write).
7.3.1.4 Message RAM
There are two types of message RAMs on this device that can be used to share between CPU, CLA and DMA. CLA-CPU message RAM shares data between the CLA and CPU while the CLA-DMA message RAM shares data between the CLA and DMA.
7.3.2 Control Law Accelerator (CLA) Memory Map
Table 7-2 shows the CLA data ROM memory map. Table 7-2. CLA Data ROM Memory Map MEMORY START ADDRESS LENGTH FFT Tables (Load) 0x0100 1070 0x0800 Data (Load) 0x0100 1870 0x078A Version (Load) 0x0100 1FFA 0x0006 FFT Tables (Run) 0x0000 F070 0x0800 Data (Run) 0x0000 F870 0x078A Version (Run) 0x0000 FFFA 0x0006 TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
208 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
7.3.3 Flash Memory Map
On the F28P55x devices, five flash banks (1084KB) are available. 4 banks are 256KB and the 5th bank is 64KB in size. Flash operations (erase and program) are performed at the bank level. Code cannot be executed from the same bank as an operation is being performed. Code can be allocated in a different flash bank, SRAM, or ROM while these operations are in progress. The Addresses of Flash Sectors table lists the addresses of flash sectors available for each part number.
7.3.3.1 Addresses of Flash Sectors
Table 7-3. Flash Memory Map PART NUMBER SECTOR ADDRESS ECC ADDRESS SIZE START END SIZE START END OTP Sectors All F28P55x TI OTP Bank 0 (Unsecure) 1520 x 16 0x0007 2000 0x0007 25EF 190 x 16 0x0107 0400 0x0107 04BD TI OTP Bank 0 (Secure) 16 x 16 0x0007 25F0 0x0007 25FF 2 x 16 0x0107 04BE 0x0107 04BE TI OTP Bank 2 1536 x 16 0x0007 4000 0x0007 45FF 192 x 16 0x0107 0800 0x0107 08BF F28P55xSJx TI OTP Bank 1 1536 x 16 0x0007 3000 0x0007 35FF 192 x 16 0x0107 0600 0x0107 06BF TI OTP Bank 3 1536 x 16 0x0007 5000 0x0007 55FF 192 x 16 0x0107 0A00 0x0107 0ABF TI OTP Bank 4 1536 x 16 0x0007 6000 0x0007 65FF 192 x 16 0x0107 0C00 0x0107 0CBF All F28P55x User configurable DCSM Z1 OTP Bank 0 512 x 16 0x0007 8000 0x0007 81FF 64 x 16 0x0107 1000 0x0107 103F User configurable DCSM Z2 OTP Bank 0 512 x 16 0x0007 8200 0x0007 83FF 64 x 16 0x0107 1040 0x0107 107F User configurable OTP Bank 2 1K x 16 0x0007 9000 0x0007 93FF 128 x 16 0x0107 1100 0x0107 117F F28P55xSJx User configurable OTP Bank 1 1K x 16 0x0007 8800 0x0007 8BFF 128 x 16 0x0107 1080 0x0107 10FF User configurable OTP Bank 3 1K x 16 0x0007 9800 0x0007 9BFF 128 x 16 0x0107 1180 0x0107 11FF User configurable OTP Bank 4 1K x 16 0x0007 A000 0x0007 A3FF 128 x 16 0x0107 1200 0x0107 127F Bank 0 Sectors All Sector 0 1K x 16 0x0008 0000 0x0008 03FF 128 x 16 0x0108 0000 0x0108 007F Sector 1 1K x 16 0x0008 0400 0x0008 07FF 128 x 16 0x0108 0080 0x0108 00FF Sector 2 1K x 16 0x000800800 0x0008 0BFF 128 x 16 0x0108 0100 0x0108 017F Sector 29 1K x 16 0x0008 7400 0x0008 77FF 128 x 16 0x0108 0E80 0x0108 0EFF Sector 30 1K x 16 0x0008 7800 0x0008 7BFF 128 x 16 0x0108 0F00 0x0108 0F7F Sector 31 1K x 16 0x0008 7C00 0x0008 7FFF 128 x 16 0x0108 0F80 0x0108 0FFF www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 209 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 7-3. Flash Memory Map (continued) PART NUMBER SECTOR ADDRESS ECC ADDRESS SIZE START END SIZE START END F28P55xSJx, F28P55xSGx, F28P55xSDx Sector 32 1K x 16 0x0008 8000 0x0008 83FF 512 x 16 0x0108 1000 0x0108 107F Sector 33 1K x 16 0x0008 8400 0x0008 87FF 512 x 16 0x0108 1080 0x0108 10FF Sector 34 1K x 16 0x0008 8800 0x0008 8BFF 512 x 16 0x0108 1100 0x0108 117F Sector 61 1K x 16 0x0008 F400 0x0008 F7FF 512 x 16 0x0108 1E80 0x0108 1EFF Sector 62 1K x 16 0x0008 F800 0x0008 FBFF 512 x 16 0x0108 1F00 0x0108 1F7F Sector 63 1K x 16 0x0008 FC00 0x0008 FFFF 512 x 16 0x0108 1F80 0x0108 1FFF F28P55xSJx, F28P55xSGx Sector 64 1K x 16 0x0009 0000 0x0009 03FF 512 x 16 0x0108 2000 0x0108 207F Sector 65 1K x 16 0x0009 0400 0x0009 07FF 512 x 16 0x0108 2080 0x0108 20FF Sector 66 1K x 16 0x0009 0800 0x0009 0BFF 512 x 16 0x0108 2100 0x0108 217F Sector 93 1K x 16 0x0009 7400 0x0009 77FF 512 x 16 0x0108 2E80 0x0108 2EFF Sector 94 1K x 16 0x0009 7800 0x0009 7BFF 512 x 16 0x0108 2F00 0x0108 2F7F Sector 95 1K x 16 0x0009 7C00 0x0009 7FFF 512 x 16 0x0108 2F80 0x0108 2FFF F28P55xSJx Sector 96 1K x 16 0x0009 8000 0x0009 83FF 512 x 16 0x0108 3000 0x0108 307F Sector 97 1K x 16 0x0009 8400 0x0009 87FF 512 x 16 0x0108 3080 0x0108 30FF Sector 98 1K x 16 0x0009 8800 0x0009 8BFF 512 x 16 0x0108 3100 0x0108 317F Sector 125 1K x 16 0x0009 F400 0x0009 F7FF 512 x 16 0x0108 3E80 0x0108 3EFF Sector 126 1K x 16 0x0009 F800 0x0009 FBFF 512 x 16 0x0108 3F00 0x0108 3F7F Sector 127 1K x 16 0x0009 FC00 0x0009 FFFF 512 x 16 0x0108 3F80 0x0108 3FFF Bank 1 Sectors F28P55xSJx only Sector 0 1K x 16 0x000A 0000 0x000A 03FF 128 x 16 0x0108 4000 0x0108 407F Sector 1 1K x 16 0x000A 0400 0x000A 07FF 128 x 16 0x0108 4080 0x0108 40FF Sector 2 1K x 16 0x000A 0800 0x000A 0BFF 128 x 16 0x0108 4100 0x0108 417F Sector 125 1K x 16 0x000B F400 0x000B F7FF 128 x 16 0x0108 7E80 0x0108 7EFF Sector 126 1K x 16 0x000B F800 0x000B FBFF 128 x 16 0x0108 7F00 0x0108 7F7F Sector 127 1K x 16 0x000B FC00 0x000B FFFF 128 x 16 0x0108 7F80 0x0108 7FFF Bank 2 Sectors All Sector 0 1K x 16 0x000C 0000 0x000C 03FF 128 x 16 0x0108 0000 0x0108 007F Sector 1 1K x 16 0x000C 0400 0x000C 07FF 128 x 16 0x0108 0080 0x0108 00FF Sector 2 1K x 16 0x000C 0800 0x000C 0BFF 128 x 16 0x0108 0100 0x0108 017F Sector 29 1K x 16 0x000C 7400 0x000C 77FF 128 x 16 0x0108 0E80 0x0108 0EFF Sector 30 1K x 16 0x000C 7800 0x000C 7BFF 128 x 16 0x0108 0F00 0x0108 0F7F Sector 31 1K x 16 0x000C 7C00 0x000C 7FFF 128 x 16 0x0108 0F80 0x0108 0FFF F28P55xSJx, F28P55xSGx, F28P55xSDx Sector 32 1K x 16 0x000C 8000 0x000C 83FF 512 x 16 0x0108 1000 0x0108 107F Sector 33 1K x 16 0x000C 8400 0x000C 87FF 512 x 16 0x0108 1080 0x0108 10FF Sector 34 1K x 16 0x000C 8800 0x000C 8BFF 512 x 16 0x0108 1100 0x0108 117F Sector 61 1K x 16 0x000C F400 0x000C F7FF 512 x 16 0x0108 1E80 0x0108 1EFF Sector 62 1K x 16 0x000C F800 0x000C FBFF 512 x 16 0x0108 1F00 0x0108 1F7F Sector 63 1K x 16 0x000C FC00 0x000C FFFF 512 x 16 0x0108 1F80 0x0108 1FFF TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
210 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 7-3. Flash Memory Map (continued) PART NUMBER SECTOR ADDRESS ECC ADDRESS SIZE START END SIZE START END F28P55xSJx, F28P55xSGx Sector 64 1K x 16 0x000D 0000 0x000D 03FF 512 x 16 0x0108 2000 0x0108 207F Sector 65 1K x 16 0x000D 0400 0x000D 07FF 512 x 16 0x0108 2080 0x0108 20FF Sector 66 1K x 16 0x000D 0800 0x000D 0BFF 512 x 16 0x0108 2100 0x0108 217F Sector 93 1K x 16 0x000D 7400 0x000D77FF 512 x 16 0x0108 2E80 0x0108 2EFF Sector 94 1K x 16 0x000D 7800 0x000D 7BFF 512 x 16 0x0108 2F00 0x0108 2F7F Sector 95 1K x 16 0x000D 7C00 0x000D 7FFF 512 x 16 0x0108 2F80 0x0108 2FFF F28P55xSJx Sector 96 1K x 16 0x000D 8000 0x000D 83FF 512 x 16 0x0108 3000 0x0108 307F Sector 97 1K x 16 0x000D 8400 0x000D 87FF 512 x 16 0x0108 3080 0x0108 30FF Sector 98 1K x 16 0x000D 8800 0x000D 8BFF 512 x 16 0x0108 3100 0x0108 317F Sector 125 1K x 16 0x000D F400 0x000D F7FF 512 x 16 0x0108 3E80 0x0108 3EFF Sector 126 1K x 16 0x000D F800 0x000D FBFF 512 x 16 0x0108 3F00 0x0108 3F7F Sector 127 1K x 16 0x000D FC00 0x000D FFFF 512 x 16 0x0108 3F80 0x0108 3FFF Bank 3 Sectors F28P55xSJx only Sector 0 1K x 16 0x000E 0000 0x000E 03FF 128 x 16 0x0108 C000 0x0108 C07F Sector 1 1K x 16 0x000E 0400 0x000E 07FF 128 x 16 0x0108 C080 0x0108 C0FF Sector 2 1K x 16 0x000E 0800 0x000E 0BFF 128 x 16 0x0108 C100 0x0108 C17F Sector 125 1K x 16 0x000F F400 0x000F F7FF 128 x 16 0x0108 FE80 0x0108 FEFF Sector 126 1K x 16 0x000F F800 0x000F FBFF 128 x 16 0x0108 FF00 0x0108 FF7F Sector 127 1K x 16 0x000F FC00 0x000F FFFF 128 x 16 0x0108F F80 0x0108 FFFF Bank 4 Sectors F28P55xSJx only Sector 0 1K x 16 0x0010 0000 0x0010 03FF 128 x 16 0x0109 0000 0x0109 007F Sector 1 1K x 16 0x0010 0400 0x0010 07FF 128 x 16 0x0109 0080 0x0190 00FF Sector 2 1K x 16 0x0010 0800 0x0010 0BFF 128 x 16 0x0109 0100 0x0109 0180 Sector 29 1K x 16 0x0010 7400 0x0010 77FF 128 x 16 0x0109 0E80 0x0109 0EFF Sector 30 1K x 16 0x0010 7800 0x0010 7BFF 128 x 16 0x0109 0F00 0x0109 0F7F Sector 31 1K x 16 0x0010 7C00 0x0010 7FFF 128 x 16 0x0109 0F80 0x0109 0FFF www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 211 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
7.3.4 Peripheral Registers Memory Map
Table 7-4. Peripheral Registers Memory Map Structure DriverLib Name Base Address CPU1 CPU1.DMA CPU1.CLA1 Pipeline Protected Peripheral Frame 0 (PF0) CPUTIMER_REGS CPUTIMER0_BASE 0x0000_0C00 YES - - - CLA_ONLY_REGS CLA1_ONLY_BASE 0x0000_0C00 - - YES - CPUTIMER_REGS CPUTIMER1_BASE 0x0000_0C08 YES - - - CPUTIMER_REGS CPUTIMER2_BASE 0x0000_0C10 YES - - - PIE_CTRL_REGS PIECTRL_BASE 0x0000_0CE0 YES - - - CLA_SOFTINT_REGS CLA1_SOFTINT_BASE 0x0000_0CE0 - - YES - PIE_VECT_TABLE PIEVECTTABLE_BASE 0x0000_0D00 YES - - - DMA_REGS DMA_BASE 0x0000_1000 YES - - - DMA_CH_REGS DMA_CH1_BASE 0x0000_1020 YES - - - DMA_CH_REGS DMA_CH2_BASE 0x0000_1040 YES - - - DMA_CH_REGS DMA_CH3_BASE 0x0000_1060 YES - - - DMA_CH_REGS DMA_CH4_BASE 0x0000_1080 YES - - - DMA_CH_REGS DMA_CH5_BASE 0x0000_10A0 YES - - - DMA_CH_REGS DMA_CH6_BASE 0x0000_10C0 YES - - - CLA_REGS CLA1_BASE 0x0000_1400 YES - - - ADC_RESULT_REGS ADCARESULT_BASE 0x0000_1800 YES YES YES - ADC_RESULT_REGS ADCBRESULT_BASE 0x0000_1880 YES YES YES - ADC_RESULT_REGS ADCCRESULT_BASE 0x0000_1900 YES YES YES - ADC_RESULT_REGS ADCDRESULT_BASE 0x0000_1980 YES YES YES - ADC_RESULT_REGS ADCERESULT_BASE 0x0000_1A00 YES YES YES - PCTRACE_BUFFER_REGS ERAD_PCTRACE_BUFFER_BASE 0x0005_FE00 YES - - YES UID_REGS UID_BASE 0x0007_2172 YES - - - DCSM_Z1_OTP DCSM_Z1OTP_BASE 0x0007_8000 YES - - - DCSM_Z2_OTP DCSM_Z2OTP_BASE 0x0007_8200 YES - - - Peripheral Frame 1 (PF1) EPWM_REGS EPWM1_BASE 0x0000_4000 YES YES YES YES EPWM_REGS EPWM2_BASE 0x0000_4100 YES YES YES YES EPWM_REGS EPWM3_BASE 0x0000_4200 YES YES YES YES EPWM_REGS EPWM4_BASE 0x0000_4300 YES YES YES YES EPWM_REGS EPWM5_BASE 0x0000_4400 YES YES YES YES EPWM_REGS EPWM6_BASE 0x0000_4500 YES YES YES YES EPWM_REGS EPWM7_BASE 0x0000_4600 YES YES YES YES EPWM_REGS EPWM8_BASE 0x0000_4700 YES YES YES YES TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
212 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 7-4. Peripheral Registers Memory Map (continued) Structure DriverLib Name Base Address CPU1 CPU1.DMA CPU1.CLA1 Pipeline Protected EPWM_REGS EPWM9_BASE 0x0000_4800 YES YES YES YES EPWM_REGS EPWM10_BASE 0x0000_4900 YES YES YES YES EPWM_REGS EPWM11_BASE 0x0000_4A00 YES YES YES YES EPWM_REGS EPWM12_BASE 0x0000_4B00 YES YES YES YES EQEP_REGS EQEP1_BASE 0x0000_5100 YES YES YES YES EQEP_REGS EQEP2_BASE 0x0000_5140 YES YES YES YES EQEP_REGS EQEP3_BASE 0x0000_5180 YES YES YES YES ECAP_REGS ECAP1_BASE 0x0000_5200 YES YES YES YES ECAP_REGS ECAP2_BASE 0x0000_5240 YES YES YES YES CMPSS_REGS CMPSS1_BASE 0x0000_5500 YES YES YES YES CMPSS_REGS CMPSS2_BASE 0x0000_5540 YES YES YES YES CMPSS_REGS CMPSS3_BASE 0x0000_5580 YES YES YES YES CMPSS_REGS CMPSS4_BASE 0x0000_55C0 YES YES YES YES PGA_REGS PGA1_BASE 0x0000_5B00 YES YES YES YES PGA_REGS PGA2_BASE 0x0000_5B10 YES YES YES YES PGA_REGS PGA3_BASE 0x0000_5B20 YES YES YES YES DAC_REGS DACA_BASE 0x0000_5C00 YES YES YES YES Peripheral Frame 2 (PF2) SPI_REGS SPIA_BASE 0x0000_6100 YES YES YES YES SPI_REGS SPIB_BASE 0x0000_6110 YES YES YES YES PMBUS_REGS PMBUSA_BASE 0x0000_6400 YES YES YES YES FSI_TX_REGS FSITXA_BASE 0x0000_6600 YES YES YES YES FSI_RX_REGS FSIRXA_BASE 0x0000_6680 YES YES YES YES Peripheral Frame 3 (PF3) ADC_REGS ADCC_BASE 0x0000_6A00 YES - YES YES ADC_REGS ADCD_BASE 0x0000_6C00 YES - YES YES ADC_REGS ADCE_BASE 0x0000_6E00 YES - YES YES ADC_REGS ADCA_BASE 0x0000_7400 YES - YES YES ADC_REGS ADCB_BASE 0x0000_7600 YES - YES YES Peripheral Frame 4 (PF4) INPUT_XBAR_REGS INPUTXBAR_BASE 0x0000_7900 YES - - YES XBAR_REGS XBAR_BASE 0x0000_7920 YES - - YES SYNC_SOC_REGS SYNCSOC_BASE 0x0000_7940 YES - - YES INPUT_XBAR_REGS CLBINPUTXBAR_BASE 0x0000_7960 YES - - YES DMA_CLA_SRC_SEL_REGS DMACLASRCSEL_BASE 0x0000_7980 YES - - YES www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 213 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 7-4. Peripheral Registers Memory Map (continued) Structure DriverLib Name Base Address CPU1 CPU1.DMA CPU1.CLA1 Pipeline Protected EPWM_XBAR_REGS EPWMXBAR_BASE 0x0000_7A00 YES - - YES CLB_XBAR_REGS CLBXBAR_BASE 0x0000_7A40 YES - - YES OUTPUT_XBAR_REGS OUTPUTXBAR_BASE 0x0000_7A80 YES - - YES OUTPUT_XBAR_REGS CLBOUTPUTXBAR_BASE 0x0000_7BC0 YES - - YES GPIO_CTRL_REGS GPIOCTRL_BASE 0x0000_7C00 YES - - YES GPIO_DATA_REGS GPIODATA_BASE 0x0000_7F00 YES - YES YES GPIO_DATA_READ_REGS GPIODATAREAD_BASE 0x0000_7F80 YES - YES YES DEV_CFG_REGS DEVCFG_BASE 0x0005_D000 YES - - YES CLK_CFG_REGS CLKCFG_BASE 0x0005_D200 YES - - YES CPU_SYS_REGS CPUSYS_BASE 0x0005_D300 YES - - YES SYS_STATUS_REGS SYSSTAT_BASE 0x0005_D400 YES - - YES PERIPH_AC_REGS PERIPHAC_BASE 0x0005_D500 YES - - YES ANALOG_SUBSYS_REGS ANALOGSUBSYS_BASE 0x0005_D700 YES - - YES Peripheral Frame 6 (PF6) ERAD_GLOBAL_REGS ERAD_GLOBAL_BASE 0x0005_E800 YES - - YES ERAD_HWBP_REGS ERAD_HWBP1_BASE 0x0005_E900 YES - - YES ERAD_HWBP_REGS ERAD_HWBP2_BASE 0x0005_E908 YES - - YES ERAD_HWBP_REGS ERAD_HWBP3_BASE 0x0005_E910 YES - - YES ERAD_HWBP_REGS ERAD_HWBP4_BASE 0x0005_E918 YES - - YES ERAD_HWBP_REGS ERAD_HWBP5_BASE 0x0005_E920 YES - - YES ERAD_HWBP_REGS ERAD_HWBP6_BASE 0x0005_E928 YES - - YES ERAD_HWBP_REGS ERAD_HWBP7_BASE 0x0005_E930 YES - - YES ERAD_HWBP_REGS ERAD_HWBP8_BASE 0x0005_E938 YES - - YES ERAD_COUNTER_REGS ERAD_COUNTER1_BASE 0x0005_E980 YES - - YES ERAD_COUNTER_REGS ERAD_COUNTER2_BASE 0x0005_E990 YES - - YES ERAD_COUNTER_REGS ERAD_COUNTER3_BASE 0x0005_E9A0 YES - - YES ERAD_COUNTER_REGS ERAD_COUNTER4_BASE 0x0005_E9B0 YES - - YES ERAD_CRC_GLOBAL_REGS ERAD_CRC_GLOBAL_BASE 0x0005_EA00 YES - - YES ERAD_CRC_REGS ERAD_CRC1_BASE 0x0005_EA10 YES - - YES ERAD_CRC_REGS ERAD_CRC2_BASE 0x0005_EA20 YES - - YES ERAD_CRC_REGS ERAD_CRC3_BASE 0x0005_EA30 YES - - YES ERAD_CRC_REGS ERAD_CRC4_BASE 0x0005_EA40 YES - - YES ERAD_CRC_REGS ERAD_CRC5_BASE 0x0005_EA50 YES - - YES ERAD_CRC_REGS ERAD_CRC6_BASE 0x0005_EA60 YES - - YES ERAD_CRC_REGS ERAD_CRC7_BASE 0x0005_EA70 YES - - YES TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
214 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 7-4. Peripheral Registers Memory Map (continued) Structure DriverLib Name Base Address CPU1 CPU1.DMA CPU1.CLA1 Pipeline Protected ERAD_CRC_REGS ERAD_CRC8_BASE 0x0005_EA80 YES - - YES PCTRACE_REGS ERAD_PCTRACE_BASE 0x0005_EAD0 YES - - YES EPG_REGS EPG1_BASE 0x0005_EC00 YES - - YES EPG_MUX_REGS EPG1MUX_BASE 0x0005_ECD0 YES - - YES DCSM_Z1_REGS DCSM_Z1_BASE 0x0005_F000 YES - - YES DCSM_Z2_REGS DCSM_Z2_BASE 0x0005_F080 YES - - YES DCSM_COMMON_REGS DCSMCOMMON_BASE 0x0005_F0C0 YES - - YES MEM_CFG_REGS MEMCFG_BASE 0x0005_F400 YES - - YES ACCESS_PROTECTION_REGS ACCESSPROTECTION_BASE 0x0005_F500 YES - - YES MEMORY_ERROR_REGS MEMORYERROR_BASE 0x0005_F540 YES - - YES TEST_ERROR_REGS TESTERROR_BASE 0x0005_F590 YES - - YES FLASH_CTRL_REGS FLASH0CTRL_BASE 0x0005_F800 YES - - YES FLASH_ECC_REGS FLASH0ECC_BASE 0x0005_FB00 YES - - YES Peripheral Frame 7 (PF7) NNPU_EXT_EVT_REGS NNPU_EXTEVT_BASE 0x0005_4000 YES - - YES NNPU_EXT_GPRCM_REGS NNPU_EXTGPRCM_BASE 0x0005_400A YES - - YES NNPU_IPSTANDARD_REGS NNPU_IPSTANDARD_BASE 0x0005_4020 YES - - YES NNPU_IPSPECIFIC_REGS NNPU_IPSPECIFIC_BASE 0x0005_4100 YES - - YES NNPU_DATA_REGS NNPU_DATA_BASE 0x0005_4700 YES - - YES NNPU_ACC_REGS NNPU_ACC_BASE 0x0005_4C00 YES - - YES NNPU_INSTRUCTION_REGS NNPU_INSTRUCTION_BASE 0x0005_5000 YES - - YES NNPU_RFDATA_REGS NNPU_RFDATA_BASE 0x0005_5800 YES - - YES MCANSS_REGS MCANASS_BASE 0x0005_9400 YES - - YES MCAN_REGS MCANA_BASE 0x0005_9600 YES - - YES MCAN_ERROR_REGS MCANA_ERROR_BASE 0x0005_9800 YES - - YES MCANSS_REGS MCANBSS_BASE 0x0005_B400 YES - - YES MCAN_REGS MCANB_BASE 0x0005_B600 YES - - YES MCAN_ERROR_REGS MCANB_ERROR_BASE 0x0005_B800 YES - - YES DCC_REGS DCC0_BASE 0x0005_E700 YES - - YES DCC_REGS DCC1_BASE 0x0005_E740 YES - - YES Peripheral Frame 8 (PF8) LIN_REGS LINA_BASE 0x0000_6800 YES YES YES YES Peripheral Frame 9 (PF9) WD_REGS WD_BASE 0x0000_7000 YES - - YES NMI_INTRUPT_REGS NMI_BASE 0x0000_7060 YES - - YES www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 215 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 7-4. Peripheral Registers Memory Map (continued) Structure DriverLib Name Base Address CPU1 CPU1.DMA CPU1.CLA1 Pipeline Protected XINT_REGS XINT_BASE 0x0000_7070 YES - - YES SCI_REGS SCIA_BASE 0x0000_7200 YES - - YES SCI_REGS SCIB_BASE 0x0000_7210 YES - - YES SCI_REGS SCIC_BASE 0x0000_7220 YES - - YES I2C_REGS I2CA_BASE 0x0000_7300 YES - - YES I2C_REGS I2CB_BASE 0x0000_7340 YES - - YES Peripheral Frame 10 (PF10) CLB_LOGIC_CONFIG_REGS CLB1_LOGICCFG_BASE 0x0000_3000 YES - YES YES CLB_LOGIC_CONTROL_REGS CLB1_LOGICCTRL_BASE 0x0000_3100 YES - YES YES CLB_DATA_EXCHANGE_REGS CLB1_DATAEXCH_BASE 0x0000_3180 YES - YES YES CLB_LOGIC_CONFIG_REGS CLB2_LOGICCFG_BASE 0x0000_3400 YES - YES YES CLB_LOGIC_CONTROL_REGS CLB2_LOGICCTRL_BASE 0x0000_3500 YES - YES YES CLB_DATA_EXCHANGE_REGS CLB2_DATAEXCH_BASE 0x0000_3580 YES - YES YES Peripheral Frame 11 (PF11) USB_REGS USBA_BASE 0x0004_0000 YES YES - YES AES_REGS AESA_BASE 0x0004_2000 YES YES - YES AES_SS_REGS AESA_SS_BASE 0x0004_2C00 YES YES - YES Peripheral Frame 12 (PF12) LFU_REGS LFU_BASE 0x0000_7FE0 YES - YES YES TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
216 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
7.4 Identification
Table 7-5 lists the Device Identification Registers. Additional information on these device identification registers can be found in the TMS320F28P55x Real-Time Microcontrollers Technical Reference Manual. See the register descriptions of PARTIDH and PARTIDL for identification of production status (TMX or TMS) and other device information. Table 7-5. Device Identification Registers NAME ADDRESS SIZE (x16) DESCRIPTION PARTIDL 0x0005 D008 2 Bits Options 14-13 1 = InstaSPIN-FOC INSTASPIN 2 = NONE 3 = NONE 10-8 0 = 56 pin (QFN) PIN_COUNT 1 = 64 pin (QFP) 2 = 80 pin (QFP) 3 = 100 pin (QFP) 4 = 128 pin (QFP) 7-6 0 = Engineering Sample (TMX) QUAL 1 = Pilot Production (TMP) 2 = Fully Qualified (TMS) PARTIDH 0x0005 D00A 2 Device part identification number TMS320F28P55xSJ9 0x09FF 0500 TMS320F28P55xSJ6 0x09FC 0500 TMS320F28P55xSJ2 0x09F8 0500 TMS320F28P55xSG9 0x09F5 0500 TMS320F28P55xSG8 0x09F4 0500 TMS320F28P55xSG2 0x09EE 0500 TMS320F28P55xSD7 0x09E9 0500 REVID 0x0005 D00C 2 Silicon revision number Revision 0 0x0000 0001 UID_UNIQUE 0x0007 2172 4 Unique identification number. This number is different on each individual device with the same PARTIDH. This unique number can be used as a serial number in the application. This number is present only on TMS devices. www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 217 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
7.5 Bus Architecture – Peripheral Connectivity
The Peripheral Connectivity table lists a broad view of the peripheral and configuration register accessibility from each bus controller. Table 7-6. Peripheral Connectivity PERIPHERAL DMA CLA C28 SYSTEM PERIPHERALS CPU Timers Y ERAD Y GPIO Data Y Y GPIO Pin Mapping and Configuration Y XBAR Configuration Y System Configuration Y AES Y Y EPG Y LFU Y Y DCC Y MEMORY M0/M1 Y LSx Y Y GSx Y Y ROM Y FLASH Y CONTROL PERIPHERALS ePWM/HRPWM Y Y Y eCAP Y Y Y eQEP (1) Y Y Y CLB Y Y ANALOG PERIPHERALS CMPSS (1) Y Y Y DAC (1) Y Y Y ADC Configuration Y Y ADC Results (1) Y Y Y PGA (1) Y Y Y COMMUNICATION PERIPHERALS MCAN(CAN-FD) (1) Y Y FSITX/FSIRX Y Y Y I2C Y LIN Y Y Y PMBus Y Y Y SCI Y SPI Y Y Y USB (1) Y Y (1) These modules are accessible from DMA but cannot trigger a DMA transfer. TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
218 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
7.6 C28x Processor
The CPU is a 32-bit fixed-point processor. This device draws from the best features of digital signal processing; reduced instruction set computing (RISC); and microcontroller architectures, firmware, and tool sets. The CPU features include a modified Harvard architecture and circular addressing. The RISC features are single-cycle instruction execution, register-to-register operations, and modified Harvard architecture. The microcontroller features include ease of use through an intuitive instruction set, byte packing and unpacking, and bit manipulation. The modified Harvard architecture of the CPU enables instruction and data fetches to be performed in parallel. The CPU can read instructions and data while it writes data simultaneously to maintain the single-cycle instruction operation across the pipeline. The CPU does this over six separate address/data buses. For more information on CPU architecture and instruction set, see the TMS320C28x CPU and Instruction Set Reference Guide.
7.6.1 Floating-Point Unit (FPU)
The C28x plus floating-point (C28x+FPU) processor extends the capabilities of the C28x fixed-point CPU by adding registers and instructions to support IEEE single-precision floating-point operations. Devices with the C28x+FPU include the standard C28x register set plus an additional set of floating-point unit registers. The additional floating-point unit registers are the following:
- Eight floating-point result registers, RnH (where n = 0–7)
- Floating-point Status Register (STF)
- Repeat Block Register (RB) All of the floating-point registers, except the RB, are shadowed. This shadowing can be used in high-priority interrupts for fast context save and restore of the floating-point registers. For more information on the C28x Floating Point Unit (FPU), see the TMS320C28x Extended Instruction Sets Technical Reference Manual.
7.6.2 Trigonometric Math Unit (TMU)
The trigonometric math unit (TMU) extends the capabilities of a C28x+FPU by adding instructions and leveraging existing FPU instructions to speed up the execution of common trigonometric and arithmetic operations listed in Table 7-7. Table 7-7. TMU Supported Instructions Instructions C Equivalent Operation Pipeline Cycles MPY2PIF32 RaH,RbH a = b * 2pi 2/3 DIV2PIF32 RaH,RbH a = b / 2pi 2/3 DIVF32 RaH,RbH,RcH a = b/c 5 SQRTF32 RaH,RbH a = sqrt(b) 5 SINPUF32 RaH,RbH a = sin(b*2pi) 4 COSPUF32 RaH,RbH a = cos(b*2pi) 4 ATANPUF32 RaH,RbH a = atan(b)/2pi 4 QUADF32 RaH,RbH,RcH,RdH Operation to assist in calculating ATANPU2 5 Exponent instruction IEXP2F32 and logarithmic instruction LOG2F32 have been added to support computation of floating-point power function for the nonlinear proportional integral derivative control (NLPID) component of the C2000 Digital Control Library. These two added instructions reduce the power function calculations from a typical of 300 cycles using library emulation to less than 10 cycles. No changes have been made to existing instructions, pipeline, or memory bus architecture. All TMU instructions use the existing FPU register set (R0H to R7H) to carry out the operations. For more information, see the TMS320C28x Extended Instruction Sets Technical Reference Manual. www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 219 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
7.6.3 VCRC Unit
Cyclic redundancy check (CRC) algorithms provide a straightforward method for verifying data integrity over large data blocks, communication packets, or code sections. The C28x+VCRC can perform 8-bit, 16-bit, 24-bit, and 32-bit CRCs. For example, the VCRC can compute the CRC for a block length of 10 bytes in 10 cycles. A CRC result register contains the current CRC, which is updated whenever a CRC instruction is executed. The following are the CRC polynomials used by the CRC calculation logic of the VCRC:
- CRC8 polynomial = 0x07
- CRC16 polynomial 1 = 0x8005
- CRC16 polynomial 2 = 0x1021
- CRC24 polynomial = 0x5d6dcb
- CRC32 polynomial 1 = 0x04c11db7
- CRC32 polynomial 2 = 0x1edc6f41 This module can calculate CRCs for a byte of data in a single cycle. The CRC calculation for CRC8, CRC16, CRC24, and CRC32 is done byte-wise (instead of computing on a complete 16-bit or 32-bit data read by the C28x core) to match the byte-wise computation requirement mandated by various standards. The VCRC Unit also allows the user to provide the size (1b-32b) and value of any polynomial to fit custom CRC requirements. The CRC execution time increases to three cycles when using a custom polynomial. For more information on the Cyclic Redundancy Check (VCRC) instruction sets, see the TMS320C28x Extended Instruction Sets Technical Reference Manual. TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
220 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
7.7 Control Law Accelerator (CLA)
The CLA Type-2 is an independent, fully programmable, 32-bit floating-point math processor that brings concurrent control-loop execution to the C28x family. The low interrupt-latency of the CLA allows it to read ADC samples "just-in-time." This significantly reduces the ADC sample to output delay to enable faster system response and higher MHz control loops. By using the CLA to service time-critical control loops, the main CPU is free to perform other system tasks such as communications and diagnostics. The control law accelerator extends the capabilities of the C28x CPU by adding parallel processing. Time-critical control loops serviced by the CLA can achieve low ADC sample to output delay. Thus, the CLA enables faster system response and higher frequency control loops. Using the CLA for time-critical tasks frees up the main CPU to perform other system and communication functions concurrently. The following is a list of major features of the CLA:
- C compilers are available for CLA software development
- Clocked at the same rate as the main CPU (SYSCLKOUT).
- An independent architecture allowing CLA algorithm execution independent of the main C28x CPU. – Complete bus architecture:
- Program Address Bus (PAB) and Program Data Bus (PDB)
- Data Read Address Bus (DRAB), Data Read Data Bus (DRDB), Data Write Address Bus (DWAB), and Data Write Data Bus (DWDB) – Independent 8-stage pipeline. – 16-bit program counter (MPC) – Four 32-bit result registers (MR0 to MR3) – Two 16-bit auxiliary registers (MAR0, MAR1) – Status register (MSTF)
- Instruction set includes: – IEEE single-precision (32-bit) floating-point math operations – Floating-point math with parallel load or store – Floating-point multiply with parallel add or subtract – 1/X and 1/sqrt(X) estimations – Data type conversions – Conditional branch and call – Data load/store operations
- The CLA program code can consist of up to eight tasks or interrupt service routines, or seven tasks and a main background task. – The start address of each task is specified by the MVECT registers. – No limit on task size as long as the tasks fit within the configurable CLA program memory space. – One task is serviced at a time until its completion. There is no nesting of tasks. – Upon task completion a task-specific interrupt is flagged within the PIE. – When a task finishes the next highest-priority pending task is automatically started. – The Type-2 CLA can have a main task that runs continuously in the background, while other high-priority events trigger a foreground task.
- Task trigger mechanisms: – C28x CPU through the IACK instruction – Task1 to Task8: up to 256 possible trigger sources from peripherals connected to the shared bus on which the CLA assumes secondary ownership. – Task8 can be set to be the background task, while Tasks 1 to 7 take peripheral triggers.
- Memory and Shared Peripherals: – Two dedicated message RAMs for communication between the CLA and the main CPU. – The C28x CPU can map CLA program and data memory to the main CPU space or CLA space. – Two dedicated message RAMs for communication between the CLA and the DMA www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 221 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
CLA_INT1 to CLA_INT8 MR0(32) MVECT1(16) MIFR(16) MPC(16) MIER(16) MIFRC(16) MIRUN(16) MR1(32) MR3(32) MAR0(16) CPU Read/Write Data Bus CLA Execution Register Set CLA Control Register Set MSTF(32) MPERINT1 to MPERINT8 SYSCLK PIE CLA Clock Enable From Shared Peripherals CLA Program Memory (LSx) CLA Data Memory (LSx) SYSRS MR2(32) MAR1(16) MIOVF(16) MICLR(16) MCTL(16) MICLROVF(16) LVF LUF CLA Message RAMs Shared PeripheralsMEALLOW CLA Data Bus C28x CPUINT11 INT12 MVECT2(16) MVECT3(16) MVECT4(16) MVECT5(16) MVECT6(16) MVECT7(16) MVECT8(16) CPU Data Bus LSxMSEL[MSEL_LSx] LSxCLAPGM[CLAPGM_LSx] CLA Program Bus MVECTBGRND(16) MVECTBGRNDACTIVE(16) MCTLBGRND(16) MSTSBGRND(16) CLA1SOFTINTEN(16) CLA1INTFRC(16) MPSACTL(16) MPSA1(32) MPSA2(32) Figure 7-2. CLA Block Diagram TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
222 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
7.8 Embedded Real-Time Analysis and Diagnostic (ERAD)
The ERAD module enhances the debug and system-analysis capabilities of the device. The debug and system- analysis enhancements provided by the ERAD module is done outside of the CPU. The ERAD module consists of the Enhanced Bus Comparator units and the System Event Counter units. The Enhanced Bus Comparator units are used to generate hardware breakpoints, hardware watch points, and other output events. The System Event Counter units are used to analyze and profile the system. The ERAD module is accessible by the debugger and by the application software, which significantly increases the debug capabilities of many real-time systems, especially in situations where debuggers are not connected. In the TMS320F28P55x devices, the ERAD module contains eight Enhanced Bus Comparator units (which increases the number of Hardware breakpoints from two to ten) and four Benchmark System Event Counter units. www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 223 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
7.9 Direct Memory Access (DMA)
The DMA module provides a hardware method of transferring data between peripherals and/or memory without intervention from the CPU, thereby freeing up bandwidth for other system functions. Additionally, the DMA has the capability to orthogonally rearrange the data as it is transferred as well as “ping-pong” data between buffers. These features are useful for structuring data into blocks for optimal CPU processing. Figure 7-3 shows a device-level block diagram of the DMA. DMA features include:
- Six channels with independent PIE interrupts
- Peripheral interrupt trigger sources – ADC interrupts and EVT signals – External Interrupts – ePWM SOC signals – CPU timers – eCAP – SPI transmit and receive – LIN transmit and receive
- Data sources and destinations: – GSx RAM – ADC result registers – Control peripheral registers (ePWM, eQEP, eCAP) – SPI, LIN, CAN, and PMBus registers – USB – PGA control registers
- Word Size: 16-bit or 32-bit (SPI limited to 16-bit)
- Throughput: Four cycles per word without arbitration DMA Trigger Source Selection DMACHSRCSEL1.CHx DMACHSRCSEL2.CHx CHx.MODE.PERINTSEL (x = 1 to 6) DMA C28x PIE DMA_CHx(1-6) CAN DMA bus LIN ADC WRAPPER ADC RESULTS Global Shared (GS0- 3) RAM C28x bus XINT TIMER eQEP eCAP EPWM TINT (0-2) XINT(1-5) ADCx.INT(1-5), ADCx.EVT ECAP(1-2)DMA EPWM(1-12).SOCA, EPWM(1-12).SOCB SPITXDMA(A-B) SPIRXDMA(A-B) FSITXADMA, FSIRXADMA FSI_DATA_TAG_MATCH, FSI_PING_TAG_MATCH CMPSS SPI PM Bus AES AESA_ContextIn, AESA_ContextOut, AESA_DataIn, AESA_DataOut LINxTXDMA, LINxRXDMA EPG CLB EPGAINT CLB1-2INT FSIDAC USB PGA Figure 7-3. DMA Block Diagram TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
224 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
7.10 Device Boot Modes
This section explains the default boot modes, as well as all the available boot modes supported on this device. The boot ROM uses the boot mode select, general-purpose input/output (GPIO) pins to determine the boot mode configuration. Table 7-8 shows the boot mode options available for selection by the default boot mode select pins. Users have the option to program the device to customize the boot modes selectable in the boot-up table as well as the boot mode select pin GPIOs used. All the peripheral boot modes that are supported use the first instance of the peripheral module (SCIA, SPIA, I2CA, CANA, and so forth). Whenever these boot modes are referred to in this chapter, such as SCI boot, it is actually referring to the first module instance, which means the SCI boot on the SCIA port. The same applies to the other peripheral boots. See the Reset - XRSn - Switching Characteristics table and the Power-on Reset figure for t boot-flash, the boot ROM execution time to first instruction fetch in flash. Table 7-8. Device Default Boot Modes BOOT MODE GPIO24 (DEFAULT BOOT MODE SELECT PIN 1) GPIO32 (DEFAULT BOOT MODE SELECT PIN 0) Parallel IO 0 0 SCI / Wait Boot (1) 0 1 CAN(MCAN-NONFD) 1 0 Flash(USB) (2) 1 1 (1) SCI boot mode can be used as a wait boot mode as long as SCI continues to wait for an 'A' or 'a' during the SCI autobaud lock process. (2) If the default flash entry address is not programmed, the boot mode will switch to USB Boot for those devices that include the USB peripheral. On devices without a USB, the action will be to enter the ITRAP ISR if the default flash entry address is not programmed. The switch to USB boot is only supported for the default flash entry address option and not all entry address options. www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 225 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
7.10.1 Device Boot Configurations
This section details what boot configurations are available and how to configure them. This device supports from 0 boot mode select pins up to 3 boot mode select pins as well as from 1 configured boot mode up to 8 configured boot modes. To change and configure the device from the default settings to custom settings for your application, use the following process: 1. Determine all the various ways you want application to be able to boot. (For example: Primary boot option of Flash boot for your main application, secondary boot option of CAN boot for firmware updates, tertiary boot option of SCI boot for debugging, etc) 2. Based on the number of boot modes needed, determine how many boot mode select pins (BMSPs) are required to select between your selected boot modes. (For example: 2 BMSPs are required to select between 3 boot mode options) 3. Assign the required BMSPs to a physical GPIO pin. (For example, BMSP0 to GPIO10, BMSP1 to GPIO51, and BMSP2 left as default which is disabled). Refer to Section 7.10.1.1 for all the details on performing these configurations. 4. Assign the determined boot mode definitions to indexes in your custom boot table that correlate to the decoded value of the BMSPs. For example, BOOTDEF0=Boot to Flash, BOOTDEF1=CAN Boot, BOOTDEF2=SCI Boot; all other BOOTDEFx are left as default/nothing). Refer to Section 7.10.1.2 for all the details on setting up and configuring the custom boot mode table. Additionally, the Boot Mode Example Use Cases section of the TMS320F28P55x Real-Time Microcontrollers Technical Reference Manual provides some example use cases on how to configure the BMSPs and custom boot tables. Note The CAN boot mode turns on the XTAL. Be sure an XTAL is installed in the application before using CAN boot mode. TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
226 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
7.10.1.1 Configuring Boot Mode Pins
This section explains how the boot mode select pins can be customized by the user, by programming the BOOTPIN-CONFIG location (refer to Table 7-9 ) in the user-configurable dual-zone security module (DCSM) OTP. The location in the DCSM OTP is Z1-OTP-BOOTPIN-CONFIG or Z2-OTP-BOOTPIN-CONFIG. When debugging, EMU-BOOTPIN-CONFIG is the emulation equivalent of Z1-OTP-BOOTPIN-CONFIG/Z2-OTP- BOOTPIN-CONFIG, and can be programmed to experiment with different boot modes without writing to OTP. The device can be programmed to use 0, 1, 2, or 3 boot mode select pins as needed. Note When using Z2-OTP-BOOTPIN-CONFIG, the configurations programmed in this location will take priority over the configurations in Z1-OTP-BOOTPIN-CONFIG. It is recommended to use Z1-OTP- BOOTPIN-CONFIG first and then if OTP configurations need to be altered, switch to using Z2-OTP- BOOTPIN-CONFIG. Table 7-9. BOOTPIN-CONFIG Bit Fields BIT NAME DESCRIPTION 31:24 Key Write 0x5A to these 8-bits to indicate the bits in this register are valid 23:16 Boot Mode Select Pin 2 (BMSP2) Refer to BMSP0 description except for BMSP2 15:8 Boot Mode Select Pin 1 (BMSP1) Refer to BMSP0 description except for BMSP1 7:0 Boot Mode Select Pin 0 (BMSP0) Set to the GPIO pin to be used during boot (up to 255): - 0x0 = GPIO0 - 0x01 = GPIO1 - and so on Writing 0xFF disables BMSP0 and this pin is no longer used to select the boot mode. The following GPIOs cannot be used as a BMSP. If selected for a particular BMSP, the boot ROM automatically selects the factory default GPIO (the factory default for BMSP2 is 0xFF, which disables the BMSP).
- GPIO 20 and GPIO 21
- GPIO 36 and GPIO 38
- GPIO 62 to GPIO 223 www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 227 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 7-10. Standalone Boot Mode Select Pin Decoding BOOTPIN_CONFIG KEY BMSP0 BMSP1 BMSP2 REALIZED BOOT MODE != 0x5A Don’t Care Don’t Care Don’t Care Boot as defined by the factory default BMSPs = 0x5A 0xFF 0xFF 0xFF Boot as defined in the boot table for boot mode (All BMSPs disabled) Valid GPIO 0xFF 0xFF Boot as defined by the value of BMSP0 (BMSP1 and BMSP2 disabled) 0xFF Valid GPIO 0xFF Boot as defined by the value of BMSP1 (BMSP0 and BMSP2 disabled) 0xFF 0xFF Valid GPIO Boot as defined by the value of BMSP2 (BMSP0 and BMSP1 disabled) Valid GPIO Valid GPIO 0xFF Boot as defined by the values of BMSP0 and BMSP1 (BMSP2 disabled) Valid GPIO 0xFF Valid GPIO Boot as defined by the values of BMSP0 and BMSP2 (BMSP1 disabled) 0xFF Valid GPIO Valid GPIO Boot as defined by the values of BMSP1 and BMSP2 (BMSP0 disabled) Valid GPIO Valid GPIO Valid GPIO Boot as defined by the values of BMSP0, BMSP1, and BMSP2 Invalid GPIO Valid GPIO Valid GPIO BMSP0 is reset to the factory default BMSP0 GPIO Boot as defined by the values of BMSP0, BMSP1, and BMSP2 Valid GPIO Invalid GPIO Valid GPIO BMSP1 is reset to the factory default BMSP1 GPIO Boot as defined by the values of BMSP0, BMSP1, and BMSP2 Valid GPIO Valid GPIO Invalid GPIO BMSP2 is reset to the factory default state, which is disabled Boot as defined by the values of BMSP0 and BMSP1 Note When decoding the boot mode, BMSP0 is the least-significant-bit and BMSP2 is the most-significant- bit of the boot table index value. It is recommended when disabling BMSPs to start with disabling BMSP2. For example, in an instance when only using BMSP2 (BMSP1 and BMSP0 are disabled), then only the boot table indexes of 0 and 4 will be selectable. In the instance when using only BMSP0, then the selectable boot table indexes are 0 and 1. TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
228 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
7.10.1.2 Configuring Boot Mode Table Options
This section explains how to configure the boot definition table, BOOTDEF, for the device and the associated boot options. The 64-bit location is located in user-configurable DCSM OTP in the Z1-OTP-BOOTDEF-LOW and Z1-OTP-BOOTDEF-HIGH locations. When debugging, EMU-BOOTDEF-LOW and EMU-BOOTDEF-HIGH are the emulation equivalents of Z1-OTP-BOOTDEF-LOW and Z1-OTP-BOOTDEF-HIGH, and can be programmed to experiment with different boot mode options without writing to OTP. The range of customization to the boot definition table depends on how many boot mode select pins (BMSP) are being used. For example, 0 BMSPs equals to 1 table entry, 1 BMSP equals to 2 table entries, 2 BMSPs equals to 4 table entries, and 3 BMSPs equals to 8 table entries. Refer to the TMS320F28P55x Real-Time Microcontrollers Technical Reference Manual for examples on how to set up the BOOTPIN_CONFIG and BOOTDEF values. Note The locations Z2-OTP-BOOTDEF-LOW and Z2-OTP-BOOTDEF-HIGH will be used instead of Z1- OTP-BOOTDEF-LOW and Z1-OTP-BOOTDEF-HIGH locations when Z2-OTP-BOOTPIN-CONFIG is configured. Refer to Configuring Boot Mode Pins for more details on BOOTPIN_CONFIG usage. Table 7-11. BOOTDEF Bit Fields BOOTDEF NAME BYTE POSITION NAME DESCRIPTION BOOT_DEF0 7:0 BOOT_DEF0 Mode/Options Set the boot mode for index 0 of the boot table. Different boot modes and their options can include, for example, a boot mode that uses different GPIOs for a specific bootloader or a different flash entry point address. Any unsupported boot mode will cause the device to either go to wait boot or boot to flash. Refer to GPIO Assignments for valid BOOTDEF values to set in the table. BOOT_DEF1 15:8 BOOT_DEF1 Mode/Options Refer to BOOT_DEF0 description BOOT_DEF2 23:16 BOOT_DEF2 Mode/Options BOOT_DEF3 31:24 BOOT_DEF3 Mode/Options BOOT_DEF4 39:32 BOOT_DEF4 Mode/Options BOOT_DEF5 47:40 BOOT_DEF5 Mode/Options BOOT_DEF6 55:48 BOOT_DEF6 Mode/Options BOOT_DEF7 63:56 BOOT_DEF7 Mode/Options www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 229 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
7.10.2 GPIO Assignments
This section details the GPIOs and boot option values used for boot mode set in the BOOT_DEF memory location located at Z1-OTP-BOOTDEF-LOW/ Z2-OTP-BOOTDEF-LOW and Z1-OTP-BOOTDEF-HIGH/ Z2-OTP- BOOTDEF-HIGH. Refer to Configuring Boot Mode Table Options on how to configure BOOT_DEF. When selecting a boot mode option, make sure to verify that the necessary pins are available in the pin mux options for the specific device package being used. Table 7-12. SCI Boot Options OPTION BOOTDEF VALUE SCITXDA GPIO SCIRXDA GPIO 0 (default) 0x01 GPIO29 GPIO28 1 0x21 GPIO16 GPIO17 2 0x41 GPIO8 GPIO9 3 0x61 GPIO2 GPIO3 4 0x81 GPIO16 GPIO3 Table 7-13. MCAN Boot Options OPTION BOOTDEF VALUE CANTXA GPIO CANRXA GPIO 0 (default) 0x08 GPIO4 GPIO5 1 0x28 GPIO1 GPIO0 2 0x48 GPIO13 GPIO12 Table 7-14. CAN(MCAN in non-FD mode) Boot Options OPTION BOOTDEF VALUE CANTXA GPIO CANRXA GPIO 0 (default) 0x02 GPIO4 GPIO5 1 0x22 GPIO1 GPIO0 2 0x42 GPIO13 GPIO12 Table 7-15. I2C Boot Options OPTION BOOTDEF VALUE SDAA GPIO SCLA GPIO 0 0x07 GPIO0 GPIO1 1 0x27 GPIO32 GPIO33 2 0x47 GPIO5 GPIO4 Table 7-16. RAM Boot Options OPTION BOOTDEF VALUE RAM ENTRY POINT (ADDRESS) 0 0x05 0x0000 0000 Table 7-17. Flash/Secure Flash Boot Options OPTION BOOTDEF VALUE FLASH ENTRY POINT (ADDRESS) FLASH SECTOR 0 (default) 0x03 0x0008 0000 Bank0 Sector 0 1 0x23 0x0008 8000 Bank 0 Sector 32 2 0x43 0x000C 0000 Bank 2 Sector 0 3 0x63 0x000C 8000 Bank 2, Sector 32 4 0x83 0x0010 0000 Bank 4, Sector 0 TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
230 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Table 7-18. LFU Flash Boot Options OPTION BOOTDEF VALUE FLASH ENTRY POINT (ADDRESS) BANK 0 (default) 0x0B 0x0008 0000 Bank0 0x000C 0000 Bank2 1 0x2B 0x0008 8000 Bank0 0x000C 8000 Bank2 Table 7-19. Wait Boot Options OPTION BOOTDEF VALUE WATCHDOG 0 0x04 Enabled 1 0x24 Disabled Table 7-20. SPI Boot Options OPTION BOOTDEF VALUE SPIPICOA SPIPOCIA SPICLKA SPISPTE 0 0x06 GPIO2 GPIO1 GPIO3 GPIO5 1 0x26 GPIO16 GPIO1 GPIO3 GPIO0 2 0x46 GPIO8 GPIO10 GPIO9 GPIO11 3 0x66 GPIO8 GPIO17 GPIO9 GPIO11 Table 7-21. Parallel Boot Options OPTION BOOTDEF VALUE D0-D7 GPIO 28x(DSP) CONTROL GPIO HOST CONTROL GPIO 0 (default) 0x00 D0 - GPIO0 GPIO16 GPIO29 D1 - GPIO1 D2 - GPIO2 D3 - GPIO3 D4 - GPIO4 D5 - GPIO5 D6 - GPIO6 D7 - GPIO7 1 0x20 D0 - GPIO0 GPIO12 GPIO13 D1 - GPIO1 D2 - GPIO2 D3 - GPIO3 D4 - GPIO4 D5 - GPIO5 D6 - GPIO6 D7 - GPIO7 Table 7-22. USB Boot Options OPTION BOOTDEF VALUE USB0 DM USB0 DP 0 (default) 0x09 GPIO23 GPIO41 www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 231 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
7.11 Security
Security features are enforced by the Dual Code Security Module (DCSM). The primary layer of defense is securing the boundary of the chip, which should always be enabled. Additionally, the Dual Zone Security feature is available to support code partitioning.
7.11.1 Securing the Boundary of the Chip
The following two features, along with authentication in the firmware update code, should be used to help to prevent unauthorized code from running on the device.
7.11.1.1 JTAGLOCK
Enabling the JTAGLOCK feature in the USER OTP disables JTAG access (for example, debug probe) to resources on the device.
7.11.1.2 Zero-pin Boot
Enabling the Zero-pin Boot option along with Flash Boot in the USER OTP blocks all pin-based external bootloader options (for example, SCI, CAN, Parallel).
7.11.2 Dual-Zone Security
The dual-zone security mechanism offers protection for two zones: Zone 1 (Z1) and Zone 2 (Z2). The security implementation for both zones is identical. Each zone has its own dedicated secure resource (OTP memory and secure ROM) and allocated secure resource (LSx RAM and flash sectors).
7.11.3 Disclaimer
Code Security Module Disclaimer THE CODE SECURITY MODULE (CSM) INCLUDED ON THIS DEVICE WAS DESIGNED TO PASSWORD PROTECT THE DATA STORED IN THE ASSOCIATED MEMORY AND IS WARRANTED BY TEXAS INSTRUMENTS (TI), IN ACCORDANCE WITH ITS STANDARD TERMS AND CONDITIONS, TO CONFORM TO TI'S PUBLISHED SPECIFICATIONS FOR THE WARRANTY PERIOD APPLICABLE FOR THIS DEVICE. TI DOES NOT, HOWEVER, WARRANT OR REPRESENT THAT THE CSM CANNOT BE COMPROMISED OR BREACHED OR THAT THE DATA STORED IN THE ASSOCIATED MEMORY CANNOT BE ACCESSED THROUGH OTHER MEANS. MOREOVER, EXCEPT AS SET FORTH ABOVE, TI MAKES NO WARRANTIES OR REPRESENTATIONS CONCERNING THE CSM OR OPERATION OF THIS DEVICE, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL TI BE LIABLE FOR ANY CONSEQUENTIAL, SPECIAL, INDIRECT, INCIDENTAL, OR PUNITIVE DAMAGES, HOWEVER CAUSED, ARISING IN ANY WAY OUT OF YOUR USE OF THE CSM OR THIS DEVICE, WHETHER OR NOT TI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. EXCLUDED DAMAGES INCLUDE, BUT ARE NOT LIMITED TO LOSS OF DATA, LOSS OF GOODWILL, LOSS OF USE OR INTERRUPTION OF BUSINESS OR OTHER ECONOMIC LOSS. TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
232 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
7.12 Watchdog
The watchdog module is the same as the one on previous TMS320C2000™ microcontrollers, but with an optional lower limit on the time between software resets of the counter. This windowed countdown is disabled by default, so the watchdog is fully backward-compatible. The watchdog generates either a reset or an interrupt. It is clocked from the internal oscillator with a selectable frequency divider. Figure 7-4 shows the various functional blocks within the watchdog module. WDCNTR Overflow 1-count delay WDCR.WDDISWDCR.WDPSWDCR.WDPRECLKDIV WDCLK (INTOSC1) WDCLK Divider Watchdog Prescaler 8-bit Watchdog Counter Watchdog Key Detector 55 + AA WDKEY (7:0) Generate 512-WDCLK Output Pulse Good Key Bad Key Out of Window Watchdog Window Detector WDWCR.MIN Count Watchdog Time-out SYSRSn Clear SCSR.WDENINT WDRSTn WDINTn WDCR(WDCHK(2:0)) 1 0 1 Figure 7-4. Windowed Watchdog www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 233 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
7.13 C28x Timers
CPU-Timers 0, 1, and 2 are identical 32-bit timers with presettable periods and with 16-bit clock prescaling. The timers have a 32-bit count-down register that generates an interrupt when the counter reaches zero. The counter is decremented at the CPU clock speed divided by the prescale value setting. When the counter reaches zero, it is automatically reloaded with a 32-bit period value. CPU-Timer 0 is for general use and is connected to the PIE block. CPU-Timer 1 is also for general use and is connected to INT13 of the CPU. CPU-Timer 2 is reserved for TI-RTOS. It is connected to INT14 of the CPU. If TI-RTOS is not being used, CPU-Timer 2 is available for general use. CPU-Timer 2 can be clocked by any one of the following:
- SYSCLK (default)
- Internal zero-pin oscillator 1 (INTOSC1)
- Internal zero-pin oscillator 2 (INTOSC2)
- X1 (XTAL) TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
234 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
7.14 Dual-Clock Comparator (DCC)
The DCC module is used for evaluating and monitoring the clock input based on a second clock, which can be a more accurate and reliable version. This instrumentation is used to detect faults in clock source or clock structures, thereby enhancing the system's safety metrics.
7.14.1 Features
The DCC has the following features:
- Allows the application to ensure that a fixed ratio is maintained between frequencies of two clock signals.
- Supports the definition of a programmable tolerance window in terms of the number of reference clock cycles.
- Supports continuous monitoring without requiring application intervention.
- Supports a single-sequence mode for spot measurements.
- Allows the selection of a clock source for each of the counters, resulting in several specific use cases.
7.14.2 Mapping of DCCx Clock Source Inputs
Table 7-23. DCCx Clock Source0 Table DCCxCLKSRC0[3:0] CLOCK NAME 0x0 XTAL/X1 0x1 INTOSC1 0x2 INTOSC2 0x4 TCK 0x5 CPU1.SYSCLK 0x8 AUXCLKIN 0xC INPUT XBAR (Output16 of input-xbar) others Reserved Table 7-24. DCCx Clock Source1 Table DCCxCLKSRC1[4:0] CLOCK NAME 0x0 PLLRAWCLK 0x2 INTOSC1 0x3 INTOSC2 0x6 CPU1.SYSCLK 0x9 Input XBAR (Output15 of the input-xbar) 0xA AUXCLKIN 0xB EPWMCLK 0xC LSPCLK 0xD ADCCLK 0xE WDCLK 0xF CAN0BITCLK others Reserved www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 235 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
7.15 Configurable Logic Block (CLB)
The C2000 configurable logic block (CLB) is a collection of blocks that can be interconnected using software to implement custom digital logic functions or enhance existing on-chip peripherals. The CLB is able to enhance existing peripherals through a set of crossbar interconnections, which provide a high level of connectivity to existing control peripherals such as enhanced pulse width modulators (ePWM), enhanced capture modules (eCAP), and enhanced quadrature encoder pulse modules (eQEP). The crossbars also allow the CLB to be connected to external GPIO pins. In this way, the CLB can be configured to interact with device peripherals to perform small logical functions such as comparators, or to implement custom serial data exchange protocols. Through the CLB, functions that would otherwise be accomplished using external logic devices can now be implemented inside the MCU. The CLB peripheral is configured through the CLB tool. For more information on the CLB tool, available examples, application reports and users guide, please refer to the following location in your C2000Ware for C2000 MCUs package (C2000Ware_2_00_00_03 and higher):
- C2000WARE_INSTALL_LOCATION\\utilities\\clb_tool\\clb_syscfg\\doc
- CLB Tool User's Guide
- Designing With the C2000™ Configurable Logic Block (CLB) Application Report
- How to Migrate Custom Logic From an FPGA/CPLD to C2000™ Microcontrollers Application Report The CLB module and its interconnections are shown in Figure 7-5. Input X-BAR Asynchronous Synchronous Sync. + Qual GPIO0 to GPIOx INPUT1 – INPUT6 CLB X-BAR Other Sources CLBx TILE OUT4/5 AUXSIG0 – AUXSIG7 CLB Global Signals Other Sources CLB CLB TILE1 CELLGPREG Local Signals I N 0 - 7 O U T 0 - 7 CLB TILEx CELLGPREG Local Signals I N 0 - 7 O U T 0 - 7 CLB INPUT X-BAR CLB OUTPUT X-BAR All CLB Tile Outputs GPIO MUX CLB Tile Outputs Intersect other Peripherals OUTPUT X-BAR INPUT1 – INPUT16 Figure 7-5. GPIO to CLB Tile Connections TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
236 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Absolute encoder protocol interfaces are now provided as Position Manager solutions in the C2000Ware MotorControl SDK. Configuration files, application programmer interface (API), and use examples for such solutions are provided with C2000Ware MotorControl SDK . In some solutions, the TI-configured CLB is used with other on-chip resources, such as the SPI port or the C28x CPU, to perform more complex functionality. www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 237 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
8 Applications, Implementation, and Layout
Information in the following applications sections is not part of the TI component specification, and TI does not warrant its accuracy or completeness. TI’s customers are responsible for determining suitability of components for their purposes, as well as validating and testing their design implementation to confirm system functionality. The Hardware Design Guide for F2800x C2000 ™ Real-Time MCU Series Application Note is an essential guide for hardware developers using C2000 devices, and helps to streamline the design process while mitigating the potential for faulty designs. Key topics discussed include: power requirements; general-purpose input/output (GPIO) connections; analog inputs and ADC; clocking generation and requirements; and JTAG debugging among many others.
8.1 TI Reference Design
The TI Reference Design Library is a robust reference design library spanning analog, embedded processor, and connectivity. Created by TI experts to help you jump start your system design, all reference designs include schematic or block diagrams, BOMs, and design files to speed your time to market. Search and download TI reference designs at Select TI reference designs. TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
238 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
9 Device and Documentation Support
TI offers an extensive line of development tools. Tools and software to evaluate the performance of the device, generate code, and develop solutions are listed below.
9.1 Device Nomenclature
To designate the stages in the product development cycle, TI assigns prefixes to the part numbers of all MCU devices and support tools. Each TMS320 ™ MCU commercial family member has one of three prefixes: TMX, TMP, or TMS (for example, TMS320F28P559SJ-Q1). Texas Instruments recommends two of three possible prefix designators for its support tools: TMDX and TMDS. These prefixes represent evolutionary stages of product development from engineering prototypes (TMX and TMDX) through fully qualified production devices and tools (TMS and TMDS). Device development evolutionary flow: TMX Experimental device that is not necessarily representative of the final device's electrical specifications and may not use production assembly flow. TMP Prototype device that is not necessarily the final silicon die and may not necessarily meet final electrical specifications. TMS Production version of the silicon die that is fully qualified. Support tool development evolutionary flow: TMDX Development-support product that has not yet completed Texas Instruments internal qualification testing. TMDS Fully-qualified development-support product. TMX and TMP devices and TMDX development-support tools are shipped against the following disclaimer: "Developmental product is intended for internal evaluation purposes." Production devices and TMDS development-support tools have been characterized fully, and the quality and reliability of the device have been demonstrated fully. TI's standard warranty applies. Predictions show that prototype devices (X or P) have a greater failure rate than the standard production devices. Texas Instruments recommends that these devices not be used in any production system because their expected end-use failure rate still is undefined. Only qualified production devices are to be used. TI device nomenclature also includes a suffix with the device family name. This suffix indicates the package type (for example, PZ). For device part numbers and further ordering information, see the TI website ( www.ti.com) or contact your TI sales representative. www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 239 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Generic Part Number: TMS 320 F28 Orderable Part Number: X F28 PREFIX(A) TMX (X) = experimental device TMS (blank) = qualified device CPU ARCHITECTURE DEVICE FAMILY 320 = TMS320 MCU Family F28 = C28 CPU P P SERIES P = Performance (150 MIPS to 600 MIPS) 559 559 MAJOR FAMILY (PLATFORM) P = 30x to 69x Industrial = Third digit is between 0 and 4 Automotive = Third digit is between 5 and 9 S S J J CORE S = 1 PDT PACKAGE TYPE PDT = 128-pin Thin Quad Flatpack (TQFP) PZ = 100-pin Low-profile Quad Flatpack (LQFP) PNA = 80-pin TQFP PM = 64-pin LQFP RSH = 56-pin Very Thin Quad Flatpack No-Lead (VQFN) R SHIPPING OPTIONS (blank) = Tray R = Tape and Reel -Q1 AUTOMOTIVE AEC-Q100 QUALIFICATION (blank) = Not AEC-Q100 qualified Q1 = AEC-Q100 qualification SPECIAL FEATURES CODE 2 = Base + 8 PWM pairs 6 = Base + CLA + CLB + USB + 12 PWM pairs + 64KB Flash 7 = Base + CLA + CLB + 12 PWM pairs + 24KB RAM 8 = Base + CLA + CLB + 12 PWM pairs 9 = Base + CLA + CLB + USB + NNPU + 12 PWM pairs + 64KB Flash MEMORY J = 1MB Flash, 133KB RAM G = 512KB Flash, 101KB RAM D = 256KB Flash, 45KB RAM A. Prefix X is used in orderable part numbers. Figure 9-1. Device Nomenclature
9.2 Markings
Figure 9-2 , Figure 9-3 , Figure 9-4 , Figure 9-5 , Figure 9-6 , Figure 9-7 , Figure 9-8 , and Figure 9-9 show the package symbolization. Table 9-1 lists the silicon revision codes. Package Pin 1 Lot Trace Code 2-digit Year/Month Code Assembly Lot Code Assembly Site Code Wafer Fab Code (one or two characters) as applicable Silicon Revision Code ECAT YMLLLLS YM LLLL S XF28P559 SJ9PDTQ $$#-YMLLLLS Figure 9-2. Package Symbolization for PDT Package – Automotive TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
240 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Wafer Fab Code (one or two characters) as applicable Silicon Revision Code ECAT YMLLLLS YM LLLL S XF28P550 SJ9PNA $$#-YMLLLLS Figure 9-6. Package Symbolization for PNA Package – Non-Automotive Package Pin 1 Lot Trace Code 2-digit Year/Month Code Assembly Lot Code Assembly Site Code Wafer Fab Code (one or two characters) as applicable Silicon Revision Code ECAT YMLLLLS YM LLLL S XF28P559 SJ9PMQ $$#-YMLLLLS Figure 9-7. Package Symbolization for PM Package – Automotive Package Pin 1 Lot Trace Code 2-digit Year/Month Code Assembly Lot Code Assembly Site Code Wafer Fab Code (one or two characters) as applicable Silicon Revision Code ECAT YMLLLLS YM LLLL S XF28P550 SJ9PM $$#-YMLLLLS Figure 9-8. Package Symbolization for PM Package – Non-Automotive TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
242 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Wafer Fab Code (one or two characters) as applicable Silicon Revision Code ECAT YMLLLLS YM LLLL S XF28P550 SJ9RSH $$#YMLLLLS TI G4 Figure 9-9. Package Symbolization for RSH Package – Non-Automotive Table 9-1. Revision Identification SILICON REVISION CODE SILICON REVISION REVID(1) ADDRESS: 0x5D00C COMMENTS Blank 0 0x0000 0000 This silicon revision is available as TMX. (1) Silicon Revision ID
9.3 Tools and Software
TI offers an extensive line of development tools. Some of the tools and software to evaluate the performance of the device, generate code, and develop solutions follow. To view all available tools and software for C2000 ™ real-time control MCUs, visit the C2000 real-time control MCUs – Design & development page. Development Tools TI Resource Explorer To enhance your experience, be sure to check out the TI Resource Explorer to browse examples, libraries, and documentation for your applications. Software Tools C2000Ware for C2000 MCUs C2000Ware for C2000 ™ MCUs is a cohesive set of software and documentation created to minimize development time. It includes device-specific drivers, libraries, and peripheral examples. DigitalPower SDK DigitalPower SDK is a cohesive set of software infrastructure, tools, and documentation designed to minimize C2000 MCU-based digital power system development time targeted for various AC-DC, DC-DC and DC-AC power supply applications. The software includes firmware that runs on C2000 digital power evaluation modules (EVMs) and TI designs (TIDs), which are targeted for solar, telecom, server, electric vehicle chargers and industrial power delivery applications. DigitalPower SDK provides all the needed resources at every stage of development and evaluation in a digital power applications. MotorControl SDK MotorControl SDK is a cohesive set of software infrastructure, tools, and documentation designed to minimize C2000 MCU-based motor control system development time targeted for various three-phase motor control applications. The software includes firmware that runs on C2000 motor control evaluation modules (EVMs) and TI designs (TIDs), which are targeted for industrial drive and other motor control, MotorControl SDK provides all the needed resources at every stage of development and evaluation for high-performance motor control applications. Code Composer Studio™ integrated development environment (IDE) Code Composer Studio is an integrated development environment (IDE) for TI's microcontrollers and processors. It comprises a suite of tools used to develop and debug embedded applications. Code Composer Studio is available for download across Windows®, Linux® and macOS® desktops. It can also be used in www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 243 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
the cloud by visiting https://dev.ti.com. Code Composer Studio includes an optimizing C/C++ compiler, source code editor, project build environment, debugger, profiler and many other features. The intuitive IDE takes you through each step of the application development flow. Familiar tools and interfaces make getting started faster than ever before. The desktop version of Code Composer Studio combines the advantages of the Eclipse software framework with advanced capabilities from TI resulting in a compelling feature-rich environment. The cloud-based Code Composer Studio leverages the Theia application framework enabling development in the cloud without needing to download and install large amounts of software. SysConfig System configuration tool SysConfig is a comprehensive collection of graphical utilities for configuring pins, peripherals, radios, subsystems, and other components. SysConfig helps you manage, expose and resolve conflicts visually so that you have more time to create differentiated applications. The tool's output includes C header and code files that can be used with software development kit (SDK) examples or used to configure custom software. The SysConfig tool automatically selects the pinmux settings that satisfy the entered requirements. The SysConfig tool is delivered integrated in CCS, as a standalone installer, or can be used via the dev.ti.com cloud tools portal. For more information about the SysConfig system configuration tool, visit the System configuration tool page. C2000 Third-party search tool TI has partnered with multiple companies to offer a wide range of solutions and services for TI C2000 devices. These companies can accelerate your path to production using C2000 devices. Download this search tool to quickly browse third-party details and find the right third-party to meet your needs. UniFlash Standalone Flash Tool UniFlash is a standalone tool used to program on-chip flash memory through a GUI, command line, or scripting interface. Models Various models are available for download from the product Design & development pages. These models include I/O Buffer Information Specification (IBIS) Models and Boundary-Scan Description Language (BSDL) Models. To view all available models, visit the Design tools & simulation section of the Design & development page for each device. Training To help assist design engineers in taking full advantage of the C2000 microcontroller features and performance, TI has developed a variety of training resources. Utilizing the online training materials and downloadable hands-on workshops provides an easy means for gaining a complete working knowledge of the C2000 microcontroller family. These training resources have been designed to decrease the learning curve, while reducing development time, and accelerating product time to market. For more information on the various training resources, visit the C2000™ real-time control MCUs – Support & training site.
9.4 Documentation Support
To receive notification of documentation updates, navigate to the device product folder on ti.com. Click on Notifications to register and receive a weekly digest of any product information that has changed. For change details, review the revision history included in any revised document. The current documentation that describes the processor, related peripherals, and other technical collateral follows. Note TI is transitioning to use more inclusive terminology. Some language may be different than what you would expect to see for certain technology areas. Errata TMS320F28P55x Real-Time MCUs Silicon Errata describes known advisories on silicon and provides workarounds. TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
244 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Technical Reference Manual TMS320F28P55x Real-Time Microcontrollers Technical Reference Manual details the integration, the environment, the functional description, and the programming models for each peripheral and subsystem in the F28P55x real-time microcontrollers. CPU User's Guides TMS320C28x CPU and Instruction Set Reference Guide describes the central processing unit (CPU) and the assembly language instructions of the TMS320C28x fixed-point digital signal processors (DSPs). This Reference Guide also describes emulation features available on these DSPs. TMS320C28x Extended Instruction Sets Technical Reference Manual describes the architecture, pipeline, and instruction set of the TMU, VCU-II, and FPU accelerators. Peripheral Guides C2000 Real-Time Control Peripherals Reference Guide describes the peripheral reference guides of the 28x DSPs. Tools Guides TMS320C28x Assembly Language Tools v22.6.0.LTS User’s Guide describes the assembly language tools (assembler and other tools used to develop assembly language code), assembler directives, macros, common object file format, and symbolic debugging directives for the TMS320C28x device. TMS320C28x Optimizing C/C++ Compiler v22.6.0.LTS User’s Guide describes the TMS320C28x C/C++ compiler. This compiler accepts ANSI standard C/C++ source code and produces TMS320 DSP assembly language source code for the TMS320C28x device. Application Reports The SMT & packaging application notes website lists documentation on TI’s surface mount technology (SMT) and application notes on a variety of packaging-related topics. Semiconductor Packing Methodology describes the packing methodologies employed to prepare semiconductor devices for shipment to end users. Calculating Useful Lifetimes of Embedded Processors provides a methodology for calculating the useful lifetime of TI embedded processors (EPs) under power when used in electronic systems. It is aimed at general engineers who wish to determine if the reliability of the TI EP meets the end system reliability requirement. An Introduction to IBIS (I/O Buffer Information Specification) Modeling discusses various aspects of IBIS including its history, advantages, compatibility, model generation flow, data requirements in modeling the input/ output structures, and future trends. Serial Flash Programming of C2000 ™ Microcontrollers discusses using a flash kernel and ROM loaders for serial programming a device. The Essential Guide for Developing With C2000 ™ Real-Time Microcontrollers provides a deeper look into the components that differentiate the C2000 Microcontroller Unit (MCU) as it pertains to Real-Time Control Systems.
9.5 Support Resources
TI E2E™ support forums are an engineer's go-to source for fast, verified answers and design help — straight from the experts. Search existing answers or ask your own question to get the quick design help you need. Linked content is provided "AS IS" by the respective contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of Use. www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 245 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
9.6 Trademarks
C2000™, TMS320C2000™, Code Composer Studio™, and TI E2E™ are trademarks of Texas Instruments. Windows® is a registered trademark of Microsoft Corporation. Linux® is a registered trademark of Linus Torvalds. macOS® is a registered trademark of Apple Inc. All trademarks are the property of their respective owners.
9.7 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
9.8 Glossary
TI Glossary This glossary lists and explains terms, acronyms, and definitions. TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
246 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
April 2024 * Initial Release TI is transitioning to use more inclusive terminology. Some language may be different than what you would expect to see for certain technology areas. For SPI, all instances of legacy terminology have been changed to controller and peripheral. All instances of legacy pin names have been changed to: POCI (Peripheral OUT Controller IN); PICO (Peripheral IN Controller OUT); and CS (Chip Select). For the I2C Bus Interface, all instances of legacy terminology have been changed to controller and target. For the CAN and LIN Interface/BUS, all instances of legacy terminology have been changed to commander and responder. For the EtherCAT Controller, all instances of legacy terminology have been changed to MainDevice (or MDevice) and SubordinateDevice (or SubDevice). www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 247 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
11 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most current data available for the designated devices. This data is subject to change without notice and revision of this document. For browser-based versions of this data sheet, refer to the left-hand navigation. TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
248 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
Reel Width (W1) REEL DIMENSIONS W Dimension designed to accommodate the component length Dimension designed to accommodate the component thickness Overall width of the carrier tape Pitch between successive cavity centers Dimension designed to accommodate the component width TAPE DIMENSIONS B0 W A0Cavity QUADRANT ASSIGNMENTS FOR PIN 1 ORIENTATION IN TAPE Pocket Quadrants Sprocket Holes Q1 Q1Q2 Q2 Q3 Q3Q4 Q4 Reel Diameter User Direction of Feed All dimensions are nominal. Device Package Type Package Drawing Pins SPQ Reel Diameter (mm) Reel Width W1 (mm) (mm) (mm) (mm) (mm) W (mm) Pin1 Quadrant www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 249 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
TAPE AND REEL BOX DIMENSIONS Width (mm) W L H All dimensions are nominal. Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) XF28P550SJ6RSHR VQFN RSH 56 4000 367.0 367.0 35.0 XF28P559SJ6PMRQ1 LQFP PM 64 1000 336.6 336.6 41.3 XF28P550SJ6PMR LQFP PM 64 1000 336.6 336.6 41.3 XF28P559SJ6PNARQ1 TQFP PNA 80 1000 336.6 336.6 41.3 XF28P550SJ6PNAR TQFP PNA 80 1000 336.6 336.6 41.3 XF28P559SJ6PZRQ1 LQFP PZ 100 1000 367.0 367.0 55.0 XF28P550SJ6PZR LQFP PZ 100 1000 367.0 367.0 55.0 XF28P559SJ6PDTRQ1 TQFP PDT 128 1000 367.0 367.0 55.0 XF28P550SJ6PDTR TQFP PDT 128 1000 367.0 367.0 55.0 TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 www.ti.com ADVANCE INFORMATION
250 Submit Document Feedback Copyright © 2024 Texas Instruments Incorporated
Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
L - Outer tray length without tabs KO - Outer tray height W - Outer tray width P1 - Tray unit pocket pitch CW - Measurement for tray edge (Y direction) to corner pocket center CL - Measurement for tray edge (X direction) to corner pocket center Text Chamfer on Tray corner indicates Pin 1 orientation of packed units. All dimensions are nominal. Device Package Type Package Name Pins SPQ Unit Array Matrix Max Temp. (Deg C) L (mm) W (mm) K0 (μm) P1 (mm) CL (mm) CW (mm) XF28P550SJ9PDT TQFP PDT 128 90 6 x 15 150 315 135.9 7620 15.4 20.3 21 XF28P559SJ9PDTQ1 TQFP PDT 128 90 6 x 15 150 315 135.9 7620 15.4 20.3 21 XF28P550SJ9PZ LQFP PZ 100 90 6 x 15 150 315 135.9 7620 20.3 15.4 15.4 XF28P559SJ9PZQ1 LQFP PZ 100 90 6 x 15 150 315 135.9 7620 20.3 15.4 15.4 XF28P550SJ9PNA TQFP PNA 80 119 7 x 17 150 315 135.9 7620 17.9 14.3 13.95 XF28P559SJ9PNAQ1 TQFP PNA 80 119 7 x 17 150 315 135.9 7620 17.9 14.3 13.95 XF28P550SJ9PM LQFP PM 64 160 8 x 20 150 315 135.9 7620 15.2 13.1 13 XF28P559SJ9PMQ1 LQFP PM 64 160 8 x 20 150 315 135.9 7620 15.2 13.1 13 XF28P550SJ9RSH VQFN RSH 56 260 10 x 26 150 315 135.9 7620 11.8 10 10.35 www.ti.com TMS320F28P550SJ, TMS320F28P559SJ-Q1 SPRSP85 – APRIL 2024 ADVANCE INFORMATION Copyright © 2024 Texas Instruments Incorporated Submit Document Feedback 251 Product Folder Links: TMS320F28P550SJ TMS320F28P559SJ-Q1
www.ti.com PACKAGE OUTLINE C 128X 0.23 0.13124X 0.4 PIN 1 ID
0.05 MIN
4X 12.4 16.1
15.9 TYP
(0.13) TYP B14.05 13.95 A 14.05 13.95 0.75 0.45 0.25 GAGE PLANE 0 -5
1.2 MAX
(1) PLASTIC QUAD FLATPACK TQFP - 1.2 mm max heightPDT0128A PLASTIC QUAD FLATPACK 4215171/A 10/2023 0.08 C NOTES: 1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing per ASME Y14.5M. 2. This drawing is subject to change without notice. 33 64 97128
0.05 C A B
SCALE: 12 DETAIL A TYPICAL SCALE 1.000
www.ti.com EXAMPLE BOARD LAYOUT
0.05 MAX
128X (1.45) 128X (0.2) (15.35) (15.35) 124X (0.4) (R0.05) TYP TQFP - 1.2 mm max heightPDT0128A PLASTIC QUAD FLATPACK 4215171/A 10/2023 NOTES: (continued) 3. Publication IPC-7351 may have alternate designs. 4. Solder mask tolerances between and around signal pads can vary based on board fabrication site. 5. For more information, see Texas Instruments literature numbers SLMA002 (www.ti.com/lit/slma002) and SLMA004 (www.ti.com/lit/slma004). LAND PATTERN EXAMPLE EXPOSED METAL SHOWN SCALE:6X SYMM SYMM 128 97 33 64 SEE DETAILS METAL SOLDER MASK OPENING NON SOLDER MASK DEFINED SOLDER MASK DETAILS EXPOSED METAL SOLDER MASK METAL UNDER SOLDER MASK SOLDER MASK DEFINED EXPOSED METAL
www.ti.com EXAMPLE STENCIL DESIGN (15.35) 124X (0.4) 128X (1.45) 128X (0.2) (15.35) (R0.05) TYP TQFP - 1.2 mm max heightPDT0128A PLASTIC QUAD FLATPACK 4215171/A 10/2023 NOTES: (continued) 6. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate design recommendations. 7. Board assembly site may have different recommendations for stencil design. SOLDER PASTE EXAMPLE BASED ON 0.1 mm THICK STENCIL SCALE:6X SYMM SYMM 128 97 33 64
MTQF013A – OCTOBER 1994 – REVISED DECEMBER 1996 1POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 PZ (S-PQFP-G100) PLASTIC QUAD FLATPACK 4040149/B 11/96 26 0,13 NOM Gage Plane 0,25 0,45 0,75 0,05 MIN 0,27 12,00 TYP 0,17 100 SQ SQ15,80 16,20 13,80 1,35 1,45 1,60 MAX 14,20 0°–7° Seating Plane 0,08 0,50 M0,08 NOTES: A. All linear dimensions are in millimeters. B. This drawing is subject to change without notice. C. Falls within JEDEC MS-026
www.ti.com PACKAGE OUTLINE C 80X 0.21 0.15 76X 0.4 0.15 0.05 4X 7.6 12.22
11.82 TYP
(0.13) TYP B10.1 9.9 A 10.1 9.9 0.7 0.5 0.25 GAGE PLANE 0 -5 (1) PLASTIC QUAD FLATPACK TQFP - 1.2 mm max heightPNA0080A PLASTIC QUAD FLATPACK 4229169/D 02/2024 0.08 C NOTES: 1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing per ASME Y14.5M. 2. This drawing is subject to change without notice. 3. Reference JEDEC registration MS-026. 21 40 6180 SCALE: 14 DETAIL A TYPICAL SCALE 1.500
www.ti.com EXAMPLE BOARD LAYOUT ALL AROUND 0.05 MIN ALL AROUND 80X (1.45) 80X (0.2) (11.4) (11.4) 76X (0.4) (R0.05) TYP TQFP - 1.2 mm max heightPNA0080A PLASTIC QUAD FLATPACK 4229169/D 02/2024 NOTES: (continued) 4. Publication IPC-7351 may have alternate designs. 5. Solder mask tolerances between and around signal pads can vary based on board fabrication site. 6. For more information, see Texas Instruments literature number SLMA004 (www.ti.com/lit/slma004). LAND PATTERN EXAMPLE EXPOSED METAL SHOWN SCALE:8X SYMM SYMM 80 61 21 40 METAL SOLDER MASK OPENING NON SOLDER MASK DEFINED SOLDER MASK DETAILS EXPOSED METAL SOLDER MASK METAL UNDER SOLDER MASK SOLDER MASK DEFINED EXPOSED METAL
www.ti.com EXAMPLE STENCIL DESIGN 80X (1.45) 80X (0.2) 76X (0.4) (R0.05) TYP (11.4) (11.4) TQFP - 1.2 mm max heightPNA0080A PLASTIC QUAD FLATPACK 4229169/D 02/2024 NOTES: (continued) 7. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate design recommendations. 8. Board assembly site may have different recommendations for stencil design. SYMM SYMM 80 61 21 40 SOLDER PASTE EXAMPLE BASED ON 0.1 mm THICK STENCIL SCALE:8X
www.ti.com PACKAGE OUTLINE C 64X 0.27 0.1760X 0.5 PIN 1 ID 4X 7.5 0.08 TYP12.2 11.8 (0.13) TYP
1.6 MAX
B NOTE 3 10.2 9.8 A NOTE 3 10.2 9.8 0.75 0.45 0.25 GAGE PLANE -70 (1.4) PLASTIC QUAD FLATPACK LQFP - 1.6 mm max heightPM0064A PLASTIC QUAD FLATPACK 4215162/A 03/2017 NOTES: 1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing per ASME Y14.5M. 2. This drawing is subject to change without notice. 3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not exceed 0.15 mm per side. 4. Reference JEDEC registration MS-026. 17 32 4964
0.08 C A B
0.08 SEATING PLANE DETAIL A SCALE: 14 DETAIL A TYPICAL SCALE 1.400
www.ti.com EXAMPLE BOARD LAYOUT ALL AROUND 0.05 MIN ALL AROUND 64X (1.5) 64X (0.3) (11.4) (11.4)60X (0.5) (R0.05) TYP LQFP - 1.6 mm max heightPM0064A PLASTIC QUAD FLATPACK 4215162/A 03/2017 NOTES: (continued) 5. Publication IPC-7351 may have alternate designs. 6. Solder mask tolerances between and around signal pads can vary based on board fabrication site. 7. For more information, see Texas Instruments literature number SLMA004 (www.ti.com/lit/slma004). LAND PATTERN EXAMPLE EXPOSED METAL SHOWN SCALE:8X SYMM SYMM 64 49 17 32 METAL SOLDER MASK OPENING NON SOLDER MASK DEFINED SOLDER MASK DETAILS EXPOSED METAL SOLDER MASK METAL UNDER SOLDER MASK SOLDER MASK DEFINED EXPOSED METAL
www.ti.com EXAMPLE STENCIL DESIGN 64X (1.5) 64X (0.3) 60X (0.5) (R0.05) TYP (11.4) (11.4) LQFP - 1.6 mm max heightPM0064A PLASTIC QUAD FLATPACK 4215162/A 03/2017 NOTES: (continued) 8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate design recommendations. 9. Board assembly site may have different recommendations for stencil design. SYMM SYMM 64 49 17 32 SOLDER PASTE EXAMPLE BASED ON 0.125 mm THICK STENCIL SCALE:8X
www.ti.com PACKAGE OUTLINE 7.1 6.9 7.1 6.9 1.0 0.8 0.05 0.00 2X 5.2 52X 0.4 2X 5.2 56X 0.65 0.45 5.3 0.1 56X 0.225 0.125 0.25 0.15 (0.1) TYP (0.17) (0.175) VQFN - 1 mm max heightRSH0056G PLASTIC QUAD FLATPACK - NO LEAD 4229539/B 08/2023 0.08 C NOTES: 1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing per ASME Y14.5M. 2. This drawing is subject to change without notice. 3. The package thermal pad must be soldered to the printed circuit board for thermal and mechanical performance. PIN 1 INDEX AREA SEATING PLANE PIN 1 ID (45 X 0.3) SYMMEXPOSED THERMAL PAD SYMM 15 28 4356
0.1 C A B
0.05 C SEE DETAIL A SCALE 2.000 A35.000 DETAIL A TYPICAL AB C
www.ti.com EXAMPLE BOARD LAYOUT 52X (0.4) (R0.05) TYP 56X (0.75) 56X (0.2) (6.65) (6.65) ( 5.3) ( 0.2) TYP VIA (1.28) TYP (1.12) TYP (1.28) TYP (1.12) TYP VQFN - 1 mm max heightRSH0056G PLASTIC QUAD FLATPACK - NO LEAD 4229539/B 08/2023 NOTES: (continued) 4. This package is designed to be soldered to a thermal pad on the board. For more information, see Texas Instruments literature number SLUA271 (www.ti.com/lit/slua271). 5. Vias are optional depending on application, refer to device data sheet. If any vias are implemented, refer to their locations shown on this view. It is recommended that vias under paste be filled, plugged or tented. SYMM SYMM LAND PATTERN EXAMPLE EXPOSED METAL SHOWN SCALE: 12X SEE SOLDER MASK DETAIL 15 28 4356 METAL EDGE SOLDER MASK OPENING EXPOSED METAL METAL UNDER SOLDER MASK SOLDER MASK OPENING EXPOSED METAL NON SOLDER MASK DEFINED (PREFERRED) SOLDER MASK DEFINED SOLDER MASK DETAILS
www.ti.com EXAMPLE STENCIL DESIGN 56X (0.75) 56X (0.2) 52X (0.4) (6.65) (6.65) 16X (1.08) 16X (1.08) (R0.05) TYP (0.64) TYP (0.64) TYP (1.28) TYP (1.28) TYP VQFN - 1 mm max heightRSH0056G PLASTIC QUAD FLATPACK - NO LEAD 4229539/B 08/2023 NOTES: (continued) 6. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate design recommendations. SOLDER PASTE EXAMPLE BASED ON 0.100 MM THICK STENCIL SCALE: 12X EXPOSED PAD 57 66% PRINTED SOLDER COVERAGE BY AREA UNDER PACKAGE SYMM SYMM 15 28 4356
www.ti.com 20-Jun-2024 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead finish/ Ball material (6) MSL Peak Temp (3) Op Temp (°C) Device Marking (4/5) Samples XF28P550SJ9PDT ACTIVE TQFP PDT 128 90 TBD Call TI Call TI -40 to 150 Samples XF28P550SJ9PM ACTIVE LQFP PM 64 160 TBD Call TI Call TI -40 to 150 Samples XF28P550SJ9PNA ACTIVE TQFP PNA 80 160 TBD Call TI Call TI -40 to 150 Samples XF28P550SJ9PZ ACTIVE LQFP PZ 100 90 TBD Call TI Call TI -40 to 150 Samples XF28P550SJ9RSH ACTIVE VQFN RSH 56 3000 TBD Call TI Call TI -40 to 150 Samples XF28P559SJ9PDTQ1 ACTIVE TQFP PDT 128 90 TBD Call TI Call TI -40 to 150 Samples XF28P559SJ9PMQ1 ACTIVE TQFP PTF 128 160 TBD Call TI Call TI -40 to 150 Samples XF28P559SJ9PNAQ1 ACTIVE TQFP PNA 80 160 TBD Call TI Call TI -40 to 150 Samples XF28P559SJ9PZQ1 ACTIVE LQFP PZ 100 90 TBD Call TI Call TI -40 to 150 Samples (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based flame retardants must also meet the <=1000ppm threshold requirement. (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. Addendum-Page 1
www.ti.com 20-Jun-2024 (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2
IMPORTANT NOTICE AND DISCLAIMER TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, regulatory or other requirements. These resources are subject to change without notice. TI grants you permission to use these resources only for development of an application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these resources. TI’s products are provided subject to TI’s Terms of Sale or other applicable terms available either on ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for TI products. TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2024, Texas Instruments Incorporated