XCL LEACH | Alldatasheet

Document overview

  • Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
  • PDF pages: 5

Technical content

RELAY – LATCHING 1PDT, LOW LEVEL TO 10 AMP (714) 736-7598 • leachcorp.com • LINA.CustomerService@LeachCorp.com The technical information provided by Leach International Corporation is to be used as a guide only, and is not meant for pub lication or as documentation for altering any existing specification. Dimensions are in inches unless otherwise specified. Rev. 6/2019

  • All weld construction
  • Contact arrangement

1 PDT

  • Designed to the performance standards of MIL-PRF-6106 PRINCIPLE TECHNICAL CHARACTERISTICS
  • Contacts rated at Low level, 28 Vdc and 115/200 Vac, 400Hz, 3Ø, case grounded
  • Weight 0.034 lbs. max
  • Dimensions 0.41in x 0.81in x 0.64in
  • Special models available upon request
  • Hermetically sealed, corrosion resistant can Applicable Socket: Contact factory Application Notes: 001 002 103B 007 023 CONTACT ELECTRICAL CHARACTERISTICS Contact rating per pole and load type [1] Load current in Amps

28 Vdc 115 Vac, 400 Hz, 1Ø

Inductive [2] 6 8 Motor 4 4 Lamp 2 2 Overload 30 60 Rupture 32 80 Low level [3] - - Time current characteristics [4] - -

RELAY – LATCHING 1PDT, LOW LEVEL TO 10 AMP COIL CHARACTERISTICS (Vdc) GENERAL CHARACTERISTICS Unless otherwise noted, the specified temperature range applies to all relay characteristics. CODE A B C N [5] R [5] V [5] Nominal operating voltage 28 12 6 28 12 6 Maximum operating voltage 29 14.5 7.3 29 14.5 7.3 Maximum pickup voltage - Cold coil at +125° C 18 9 4.5 18 9 4.5 - During high temp test at +125° C 19.8 9.9 5 19.8 9.9 5 Maximum drop-out voltage 7 4.5 2.5 7 4.5 2.5 Coil resistance in Ω ±10% at +25° C except types "C" & "V" +20%, -10% 730 182 43 730 182 43 Temperature range -70°C to +125°C Minimum operating cycles (life) at rated load 50,000 Minimum operating cycles (life) at 25% rated load 200,000 Dielectric strength at sea level - All circuits to ground and circuit to circuit 1000 Vrms Dielectric strength at sea level - Coil to ground 1000 Vrms Dielectric strength at altitude 80,000 ft. 500 Vrms [6] Insulation resistance - Initial (500 Vdc) 100 M Ω min Insulation resistance - After environmental tests (500 Vdc) 50 M Ω min Sinusoidal vibration (A, D and J mounting) 0.12 d.a. / 10 to 70 Hz 30G / 70 to 3000 Hz Sinusoidal vibration (G mounting) 0.12 d.a. / 10 to 57 Hz 20G /57 to 3000 Hz Random vibration - Applicable specification MIL-STD-202 - Method 214 - Test condition - A, D and J mounting 1G (0.4G2/Hz, 50 to 2000 Hz) - Test condition - E and G mounting (E in track) 1E (0.2G2/Hz, 50 to 2000 Hz) - Duration 15 minutes each plane Shock (A, D and J mounting) 200G / 6 ms Shock (G mounting) 100G / 6 ms Maximum contact opening time under vibration and shock 10 μs Operate time at nominal voltage @ 25°C 6 ms max Release time at nominal voltage @ 25°C 6 ms max Contact make bounce at nominal voltage @ 25°C 1 ms max Contact release break bounce at nominal voltage @ 25°C 0.5 ms max [7] Weight maximum 0.034 lbs.

RELAY – LATCHING 1PDT, LOW LEVEL TO 10 AMP MOUNTING STYLES Dimensions in inches Tolerances, unless otherwise specified, XX ± 0.03 in., XXX ± 0.010

RELAY – LATCHING 1PDT, LOW LEVEL TO 10 AMP TERMINAL TYPES Dimensions in inches Tolerances, unless otherwise specified, XX ± 0.03 in., XXX ± 0.010

RELAY – LATCHING 1PDT, LOW LEVEL TO 10 AMP DIAGRAMS TOL: .XX ±.03; .XXX ±.010 NUMBERING SYSTEM NOTES 1. Standard Intermediate current test applicable. 2. Inductive load life, 20,000 cycles. AC; 10,000 cycles DC. 3. Low level enducrance test: contact load of 10 to 50 millivolt, 10 to 50 microamp, 100 Ohm max. contact resistance. 4. Refer to MIL-R-6106 for details. 5. "N" "R" & "V" coils have back EMF suppression to 42 volts maximum. 6. 500 Vrms with silicone rubber gasket compressed, 250 Vrms all other conditions. 7. Applicable to Type "N", "R" & "V" coils only. 8. Relay will not operate, but will not be damaged by application of reverse polarity on coil For any inquiries, please contact your local sales representative: leachcorp.com XCL - A 1 A - XXX Basic series designation 1. Mounting styles (A, D, E, G, J) 2. Terminal types (1, 2, 4, 7) 3. Coil voltage, see coil characteristics (A, B, C, M, N, R, V) 4. XXX Designators Dimensions in inches Tolerances, unless otherwise specified, XX ± 0.03 in., XXX ± 0.010