X2AS ANAREN | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 2

Technical content

Place Manufacturing. USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 544-2414 +44 2392-232392 Model X2AS Rev. A SMT Crossover

Description

The X2AS is a low profile crossover to intersect an RF and DC circuit trace in an easy to use surface mount package designed for frequencies up to 6 GHz. The X2AS is ideal for any application where an RF circuit must intersect with a DC circuit without resorting to a multilayer PCB. Parts have been subjected to rigorous qualification testing and units are 100% tested. They are manufactured using materials with x and y thermal expansion coefficients compatible with common substrates such as FR4, G-10, and polyimide. ELECTRICAL SPECIFICATIONS** Frequency Port Impedance Return Loss GHz Ohms dB Min DC – 2.5 50 20 2.5 – 4.0 50 20 4.0 – 6.0 50 15 Insertion Loss Power QQQQJC Operating Temp. dB Max Watts ºC / Watt ºC 0.05 30 250.9 -55 to +85 0.10 15 250.9 -55 to +85 Features:

  • DC – 6.0 GHz
  • RF – DC Crossover
  • Low Loss
  • DC Isolation
  • Surface Mountable
  • Tape And Reel
  • Convenient Package
  • Lead Free
  • 100 % Tested 0.15 10 250.9 -55 to +85 **Specification based on performance of unit properly installed on microstrip printed circuit boards with 50 W nominal impedance. Specifications subject to change without notice. Outline Drawing X2AS Mechanical Outline Dimensions are in Inches [Millimeters] Side View Bottom View (Far-side)Top View (Near-side) .200±.010 [5.08±0.25] .200±.010 [5.08±0.25] .047±.005 [1.19±0.13] 4X .033±.008 SQ [0.83±0.20] 2X .056±.004 [1.42±0.10] .039±.004 [1.00±0.10] GND GND RF IN / OUT RF IN / OUT GND GND GND GND RF IN / OUT RF IN / OUT 2X .026±.004 [0.65±0.10]

USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 544-2414 +44 2392-232392 Available on Tape and Reel For Pick and Place Manufacturing. Model X2AS Rev. A Typical Performance: 0.5 GHz to 6.0 GHz Mounting Mounting Footprint In order for Xinger crossovers to work optimally, there must be 50 transmission lines leading to and from all of the RF ports. Also, there must be a very good ground to the corners of the crossover to insure proper electrical performance. If either of these two conditions are not satisfied, insertion loss, VSWR and isolation parameters may not meet published specifications. When a surface mount crossover is mounted to a printed circuit board, the primary concerns are; insuring the RF pads of the device are in contact with the circuit trace of the PCB and insuring the ground plane of neither the component nor the PCB is in contact with the RF signal. Since the component is not symmetrical, the crossovers are specifically oriented in the tape and reel. An example of how the PCB footprint could look is shown below. In specific designs, the 50 lines need to be adjusted to the unique dielectric coefficients and thicknesses as well as varying pick and place equipment tolerances. X2AS Mounting Footprint Dimensions are in Inches [Millimeters] DC Line Transmission Line .063 SQ TYP [1.60] .034 TYP [0.86] Mutiple plated thru holes to ground .148 [3.75] To ensure proper electrical and thermal performance there must be a ground plane with 100% solder connection underneath the part Return Loss X2AS -60 -50 -40 -30 -20 -10 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 Frequency (MHz) Return Loss (dB) Insertion Loss X2AS -0.50 -0.40 -0.30 -0.20 -0.10 0.00 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 Frequency (MHz) Insertion Loss (dB)