WP710A10IT_15 KINGBRIGHT | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 6
Technical content
Features
z Low power consumption. z Popular T-1 diameter package. z General purpose leads. z Reliable and rugged. z Long life - solid state reliability. z Available on tape and reel. z RoHS compliant.
Description
The High Efficiency Red source color devices are made with Gallium Arsenide Phosphide on Gallium Phosphide Orange Light Emitting Diode. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.25(0.01") unless otherwise noted. 3. Lead spacing is measured where the leads emerge from the package. 4. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.
SPEC NO: DSAL0508 REV NO: V.4A DATE: JAN/17/2015 PAGE: 2 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1101029117 Selection Guide Absolute Maximum Ratings at TA=25°C Electrical / Optical Characteristics at TA=25°C Notes: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. 2. 2mm below package base. 3. 5mm below package base. Part No. Dice Lens Type Iv (mcd) [2] @ 10mA Viewing Angle [1] Min. Typ. 2 θ1/2 WP710A10IT High Efficiency Red (GaAsP/GaP) Red Transparent 20 60 *12 *30 34° Symbol Parameter Device Typ. Max. Units Test Conditions λpeak Peak Wavelength High Efficiency Red 627 nm I F=20mA λD [1] Dominant Wavelength High Efficiency Red 617 nm I F=20mA Δλ1/2 Spectral Line Half-width High Efficiency Red 45 nm I F=20mA C Capacitance High Efficiency Red 15 pF V F=0V;f=1MHz VF [2] Forward Voltage High Efficiency Red 2 2.5 V I F=20mA IR Reverse Current High Efficiency Red 10 uA V R = 5V Parameter High Efficiency Red Units Power dissipation 75 mW DC Forward Current 30 mA Peak Forward Current [1] 160 mA Reverse Voltage 5 V Operating/Storage Temperature -40°C To +85°C Lead Solder Temperature [2] 260°C For 3 Seconds Lead Solder Temperature [3] 260°C For 5 Seconds Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity/ luminous Flux: +/-15%. *Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Notes: 1. Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. 3. Wavelength value is traceable to the CIE127-2007 compliant national standards. 4. Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or premature failure.
SPEC NO: DSAL0508 REV NO: V.4A DATE: JAN/17/2015 PAGE: 3 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1101029117 High Efficiency Red WP710A10IT
SPEC NO: DSAL0508 REV NO: V.4A DATE: JAN/17/2015 PAGE: 4 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1101029117 PACKING & LABEL SPECIFICATIONS WP710A10IT Terms and conditions for the usage of this document 1. The information included in this docum ent reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applicati ons. If customer's application ha s special reliability requirements or have life-threatening liabilitie s, such as automotive or m edical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes
SPEC NO: DSAL0508 REV NO: V.4A DATE: JAN/17/2015 PAGE: 5 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1101029117
SPEC NO: DSAL0508 REV NO: V.4A DATE: JAN/17/2015 PAGE: 6 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1101029117