WP710A10ID14V KINGBRIGHT | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 6

Technical content

Features

z Low power consumption. z Popular T-1 diameter package. z General purpose leads. z Reliable and rugged. z Long life - solid state reliability. z Available on tape and reel. z 14V internal resistor. z RoHS compliant. Descriptions z The High Efficiency Red source color devices are made with Gallium Arsenide Phosphide on Gallium Phosphide Orange Light Emitting Diode. z Electrostatic discharge and power surge could damage the LEDs. z It is recommended to use a wrist band or anti- electrostatic glove when handling the LEDs. z All devices, equipments and machineries must be electrically grounded. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.25(0.01") unless otherwise noted. 3. Lead spacing is measured where the leads emerge from the package. 4. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES

SPEC NO: DSAL0506 REV NO: V.5A DATE: JAN/22/2015 PAGE: 2 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1101029207 Selection Guide Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity/ luminous Flux: +/-15%. * Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Absolute Maximum Ratings at TA=25°C Electrical / Optical Characteristics at TA=25°C Note: 1.Wavelength: +/-1nm. 2.Wavelength value is traceable to the CIE127-2007 compliant national standards. 3.Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Notes: 1. 2mm below package base. 2. 5mm below package base. Part No. Dice Lens Type Iv (mcd) [2] V= 14V Viewing Angle [1] Min. Typ. 2 θ1/2 High Efficiency Red (GaAsP/GaP) Red Diffused 10 20 40° *5 *10 WP710A10ID14V Symbol Parameter Device Typ. Max. Units Test Conditions λpeak Peak Wavelength High Efficiency Red 627 nm V F=14V λD [1] Dominant Wavelength High Efficiency Red 617 nm V F=14V Δλ1/2 Spectral Line Half-width High Efficiency Red 45 nm V F=14V IF Forward Current High Efficiency Red 10.5 13.5 mA V F=14V IR Reverse Current High Efficiency Red 10 uA V R = 5V Parameter High Efficiency Red Units Power dissipation 160 mW Forward Voltage 16 V Reverse Voltage 5 V Operating Temperature -40°C To +70°C Storage Temperature -40°C To +85°C Lead Solder Temperature [1] 260°C For 3 Seconds Lead Solder Temperature [2] 260°C For 5 Seconds

SPEC NO: DSAL0506 REV NO: V.5A DATE: JAN/22/2015 PAGE: 3 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1101029207 High Efficiency Red WP710A10ID14V

SPEC NO: DSAL0506 REV NO: V.5A DATE: JAN/22/2015 PAGE: 4 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1101029207 PACKING & LABEL SPECIFICATIONS WP710A10ID14V Terms and conditions for the usage of this document 1. The information included in this docum ent reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applicati ons. If customer's application ha s special reliability requirements or have life-threatening liabilitie s, such as automotive or m edical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes

SPEC NO: DSAL0506 REV NO: V.5A DATE: JAN/22/2015 PAGE: 5 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1101029207

SPEC NO: DSAL0506 REV NO: V.5A DATE: JAN/22/2015 PAGE: 6 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1101029207