WL50S_V03 BANNER | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 4

Technical content

Chemically Resistant LED work lighting

  • Three lens options, depending on model, to vary spot size
  • Illuminates a large area with an even pattern of light and no shadows
  • 12 to 30 V dc operation
  • 56 mm (2.2 in) diameter with flat profile and 30 mm (1.2 in) mounting base
  • Rugged, Viton ® o-ring sealed housing rated to IP69K
  • Chemically resistant 316 stainless steel housing for use in harsh environments
  • FDA grade silicone gasket WARNING: Not To Be Used for Personnel Protection Never use this device as a sensing device for personnel protection. Doing so could lead to serious injury or death. This device does not include the self-checking redundant circuitry necessary to allow its use in personnel safety applications. A sensor failure or malfunction can cause either an energized or de-energized sensor output condition. Models Model LED Color Window Material Lumens Lux Lens Angle (see Beam Patterns on page 2) Connection 0.5 m 1 m WL50SWSSL5Q White, 5000–8300 K Polycarbonate 295 13780 3445 ±5° small, more focused spot 5 pin Euro integral QD connector (use with a 4- wire or 5-wire mating cordset, only 2 wires used for connection) WL50SWSSGL5Q Glass WL50SWSSL11Q Polycarbonate 285 5460 1365 ±11° larger spotWL50SWSSGL11Q Glass WL50SWSSL20Q Polycarbonate 270 2000 500 ±20° largest spotWL50SWSSGL20Q Glass Specifications Supply Voltage and Current Operating Voltage: 12 to 30 V dc Current Draw: 400 mA maximum Supply Protection Circuitry Protected against reverse polarity and transient voltages Light Source Three high-intensity LEDs; see models table for color temperature Useful Life When operating within specifications, output will decrease less than 30% after 50,000 hours. Construction 316 stainless steel housing, polycarbonate or glass window with Viton seal, 316 stainless steel M30 mounting nut, FDA grade silicon base gasket Mounting 30 × 1.5 mm thread base mount Connections Integral 5-pin M12 quick disconnect fitting; 4-pin connecting cordset required for quick disconnect fitting models; only 2 wires used Environmental Rating IEC IEC IP67, IEC IP69K per DIN 40050-9 NOTE: Do not spray the cable with a high-pressure sprayer or cable damage will result. Operating Conditions 95% maximum relative humidity (non-condensing) Vibration and Mechanical Shock All models meet Mil. Std. 202F requirements method 201A (vibration: 10 to 60 Hz max., double amplitude 0.06", maximum acceleration 10G). Also meets IEC 947-5-2; 30G 11 ms duration, half sine wave. Storage Temperature 95% maximum relative humidity (non-condensing) Certifications Approvals are pending WL50S Stainless Steel High-Intensity Work Spot Light Original Document 168649 Rev. D

19 December 2016

Percentage of Maximum Light Intensity Per Lens Type at 0.5 Meter (Typical) at 1 Meter (Typical) 0 % 25 % 50 % 75 % 100 % - 3 0 - 2 0 - 1 0 0 1 0 2 0 3 0 Percentage of Max Light Intensity (Lux or mW/cm² %) Light Pattern From Center (cm) ±5º±11º±20º 0 % 25 % 50 % 75 % 100 % - 6 0 - 5 0 - 4 0 - 3 0 - 2 0 - 1 0 0 1 0 2 0 3 0 4 0 5 0 6 0 Percentage of Max Light Intensity (Lux or mW/cm² %) Light Pattern From Center (cm) ±5º ±11º ±20º Dimensions Wiring 12–30 V dc Female Male Wiring Key: 1 = Brown 3 = Blue WL50S Stainless Steel High-Intensity Work Spot Light 2 www.bannerengineering.com - Tel: +1-763-544-3164 P/N 168649 Rev. D

4-Pin Threaded M12/Euro-Style Cordsets Model Length Style Dimensions Pinout (Female) MQDC-406 1.83 m (6 ft) Straight 44 Typ. ø 14.5 M12 x 1 1 = Brown 2 = White 3 = Blue 4 = Black MQDC-415 4.57 m (15 ft) MQDC-430 9.14 m (30 ft) MQDC-450 15.2 m (50 ft) MQDC-406RA 1.83 m (6 ft) Right-Angle 32 Typ.[1.26"] 30 Typ.[1.18"] ø 14.5 [0.57"] M12 x 1 MQDC-415RA 4.57 m (15 ft) MQDC-430RA 9.14 m (30 ft) MQDC-450RA 15.2 m (50 ft) Washdown Rated Cordsets Polypropylene jacket and connector body, stainless steel coupling nut 5-Pin Threaded M12/Euro-Style Cordsets—Washdown, with Shield Model Length Style Dimensions Pinout (Female) MQDCWD-506 1.83 m (6 ft) Straight 42 Typ.[1.65"] ø 15.0[0.57"] M12 x 1 1 = Brown 2 = White 3 = Blue 4 = Black 5 = Gray MQDCWD-530 9.14 m (30 ft) Mounting Brackets All measurements are in mm SMB30A

  • Right-angle bracket with curved slot for versatile orientation
  • Clearance for M6 (¼ in) hardware
  • Mounting hole for 30 mm sensor
  • 12-ga. stainless steel

69 A B

C Hole center spacing: A to B=40 Hole size: A=ø 6.3, B= 27.1 x 6.3, C=ø 30.5 SMB30SC

  • Swivel bracket with 30 mm mounting hole for sensor
  • Black reinforced thermoplastic polyester
  • Stainless steel mounting and swivel locking hardware included B A Hole center spacing: A=ø 50.8 Hole size: A=ø 7.0, B=ø 30.0 WL50S Stainless Steel High-Intensity Work Spot Light P/N 168649 Rev. D www.bannerengineering.com - Tel: +1-763-544-3164 3
  • Swivel bracket with tilt and pan movement for precise adjustment
  • Mounting hole for 30 mm sensor
  • 12-ga. 304 stainless steel
  • Easy sensor mounting to extrude rail T-slot
  • Metric and inch size bolt available A B 68.9 36.3 83.2 Bolt thread: SMB30FA, A= 3/8 - 16 x 2 in; SMB30FAM10, A= M10 - 1.5 x 50 Hole size: B= ø 30.1 SMBAMS30RA
  • Right-angle SMBAMS series bracket
  • 30 mm hole for mounting sensors
  • Articulation slots for 90°+ rotation
  • 12-ga. (2.6 mm) cold-rolled steel A C B Hole center spacing: A=26.0, A to B=13.0 Hole size: A=26.8 x 7.0, B=ø 6.5, C=ø 31.0 SMB30MM
  • 12-ga. stainless steel bracket with curved mounting slots for versatile orientation
  • Clearance for M6 (¼ in) hardware
  • Mounting hole for 30 mm sensor A B C Hole center spacing: A = 51, A to B = 25.4 Hole size: A = 42.6 x 7, B = ø 6.4, C = ø 30.1 SMBAMS30P
  • Flat SMBAMS series bracket
  • 30 mm hole for mounting sensors
  • Articulation slots for 90°+ rotation
  • 12-ga. 300 series stainless steel 93 A C B Hole center spacing: A=26.0, A to B=13.0 Hole size: A=26.8 x 7.0, B=ø 6.5, C=ø 31.0 Banner Engineering Corp. Limited Warranty Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product. THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE. This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE. Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously manufactured by Banner Engineering Corp. Any misuse, abuse, or improper application or installation of this product or use of the product for personal protection applications when the product is identified as not intended for such purposes will void the product warranty. Any modifications to this product without prior express approval by Banner Engineering Corp will void the product warranties. All specifications published in this document are subject to change; Banner reserves the right to modify product specifications or update documentation at any time. Specifications and product information in English supersede that which is provided in any other language. For the most recent version of any documentation, refer to: www.bannerengineering.com. WL50S Stainless Steel High-Intensity Work Spot Light © Banner Engineering Corp. All rights reserved