VP-1410A ETC1 | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 5

Technical content

Eletech Electronics, Inc.

16019 Kaplan Avenue

Industry, CA 91744, U.S.A. Tel: (626) 333-6394 Fax: (626) 333-6494 Eletech Enterprise Co., Ltd. 531-3F Chung-Cheng Road Hsin Tien, Taipei Hsien, Taiwan Tel:+886 2-2218-0068 Fax:+886 2-2218-0254 http://www.eletech.com

FEATURES

nHigh quality voice & sound generation n10 messages with direct trigger pins nPlayback-only with external EPROM or ROM nStand-alone operation n128K x 8 direct memory addressing, expandable nSingle 5V DC supply voltage GENERAL DESCRIPTIONS The VP-1410A Digital Voice Processor is an advanced CMOS LSI chip designed for multiple-message playback applications. It can access up to 10 different messages of variable length stored in external EPROM or ROM chips. Message activation is simplified since each message has its own trigger pin . If memory bank switching technique is used, the number of messages supported can be easily expanded to 20, 40 or more.

APPLICATIONS

nMultiple message playback nSound effects generator nLow power consumption nInternal RC oscillator or external clock nContinuous Variable Slope Delta (CVSD) modulation nSampling rate from 24Kbps to 128 Kbps nMessage digitization with the VP-880 system n48-pin DIP (VP-1410A) or 48-pin QFP (VP-1410AF) The VP-1410A is totally self-contained. It can access the external memory all by itself without the help from any microprocessor. Although the chip provides only 16 address lines, an external counter can be easily added to extend the memory addressing to virtuely no limitation. Therefore very long message length can be achieved easily. Overall, the VP-1410A offers high voice quality and flexible memory addressing that no other chips can. nDigital message repeaters for consumer, industrial, security and telecommunication products VP-1410A Digital Voice Processor VP-1410A (DIP48) Pin Assignment VP-1410AF (QFP48) Pin Assignment

ABSOLUTE MAXIMUM RATINGS* * Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.

ELECTRICAL CHARACTERISTICS

(VDD = 5V, FOSC = 2048KHz, FCLOCK = 32 KHz unless otherwise specified) Symbol Parameter Min. Typ. Max. Units VDD Supply Voltage 4.5 5 5.5 V IDD Standby Current 1.4 mA IDRIVE Clock Drive Current 12 mA ISINK Clock Sink Current 12 mA VIH Input High 3.5 5 V VIL Voltage Low 0 1.5 V IDRIVE Output Drive 3 4 mA ISINK Current Sink 3 4 mA TRESET Reset Pulse Width 500 ns Ttr I/O Input Pulse Width 35 us FC Internal Memory Search Clock 12 MHz TIMING DIAGRAM SYSTEM CLK (internal) BUSY (internal) READ I/O RESET I/O SCAN (internal) 12MHz 12MHz Ttr

Output, address bus, expandable by adding a counter. Note that VP-1410AF does not have A16. ANG & ANG Output, differential analog audio signal. ANGD Input, analog signal to be connected to the external comparator output. Input, internal RC oscillator. If external clock is to be used, it must be connected to this pin and its frequency 64x the sampling rate. CLK DRV Output, buffered clock signal, a square wave of the same frequency as the sampling rate. D0 - D7 Input, data bus. ENV Input, to be connected to an external integrator output. INT Output, connected to an external integrator to produce envelope waveform. GND Ground. I/O1 ~ I/O10 Input/output, trigger pin, active low. I/O1 is for message #1, I/O2 is for message #2 and etc. When the chip is idle but not under reset, this pin is the trigger input and pulsing it will put the chip in the "Play" mode and start the message. Once in the "Play" mode, the pin becomes a "low" output until the message is over. Output, internal oscillator pin. Leave un-connected when using external clock. READ Output, active low. It indicates the chip is in the "Play" mode. This signal is usually used to enable memory output. RESET Input, active high. Reset the chip back to the "Idle" mode. This pin is level sensitive. TEST For factory use only, keep it un-connected. VCC Input, supply voltage. Block Diagram ADDRESS GENERATOR OSC. & TIMING CTRL A16 READ ANG TEST GND VDD ENV INT CVSD DEMODULATOR VDD GND RESET I/O CONTROL & LATCH I/O SCANNER 12MHz CLOCK 6-AA FLAG RECEIVER ANG ANGD CLK DRV INPUT BUFFER & SHIFT REGISTER

  1. 10-Message Playback, 8M EPROM APPLICATION NOTES 1. VP-1410AF Missing A16 Due to packaging constraint, the VP-1410AF does not provide address line A16. Therefore, A16 must be gener- ated externally by adding a binary counter, as explained below. 2. Memory Address Expansion The VP-1410A’s internal 17-bit address counter covers memory space up to 128K x 8, or 1M bits. It can be easily expanded by just adding an external binary counter, clocked by the falling edge of address line A16. The first counter output becomes A17, the second output becomes A18 and etc. This is possible since once started, the VP- 1410A will continue to play until it reaches the EOM (End Of Message) flag. When the internal address counter reaches the maximum count before the chip sees the EOM flag, the counter simply overflows and restarts from zero again. Therefore the VP-1410A can access an unlimited amount of memory by adding an external address counter. 3. EOM (End Of Message) Flag The EOM flag consists of six consecutive bytes of "AA", or "10101010" in binary format. After a trigger signal is received, the VP-1410A uses the internal 12MHz system clock to scan through memory space and finds the correct message by counting the number of EOM flags. For example, to find the 5th message, it must scan through each and every memory location until it finds 4 EOM flags. The first byte following the 4th EOM flag is the first byte of the 5th message. 4. Creating Master EPROM File on the VP-880 System Follow these steps to create the master EPROM file: 1. Digitize, edit and save each message in a separate file. 2. Use VP-880’s function "H" to combine all the messages together. The VP-880 program will automatically search and eliminate any EOM flag within each messge, which is naturally formed during digitization. It will then put a EOM flag at the end of each message and combine them into one or several master files.