SD7763-4-3 WINCHESTER | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 2

Technical content

FLATS (180° APART) 9/16" WRENCH MARK: 7763-4-3 (DATE CODE) 5.254 133.45 .905 22.99 .804 20.42 FLATS (180° APART) 3/4" WRENCH CATALOG P/N: 7763-4-3 CONTACTS: .000100 MIN GOLD PER ASTM B488 OVER COPPER FLASH PER ASTM B734 (RoHS) 4. ELECTRICAL SPECIFICATIONS: LOW VOLTAGE CONTACTS: 42 - 60 VAC, 1 AMP AUX ELECTRICAL CONTACTS: 600 VAC, 10 AMP 5. ENVIRONMENTAL: OPERATING TEMPERATURE RATING: -40°C TO 75°C NON-OPERATING/STORAGE TEMPERTURE RATING: -40°C TO 85°C HUMIDITY: <95 RH (AT 40°C) .000080 MIN NICKEL PER AMS-QQN-290 (RoHS) CRIMP SLEEVE: .000100 MIN NICKEL PER AMS-QQ-N-290 OVER NOTES: UNLESS OTHERWISE SPECIFIED 1. INTERFACE COMPLIANT TO SMPTE 304 SPECIFICATION. 2. MATERIAL SPECIFICATIONS: CONTACTS: COPPER ALLOY ALIGNMENT PINS: BRASS PER ASTM B16 CRIMP SLEEVE: PHOS. BRONZE O-RINGS AND STRAIN RELIEF: SILICONE RUBBER ALL PLASTIC PARTS: 20% GLASS FILLED POLYPROPYLENE ALL OTHER METAL PARTS: 303 STAINLESS STEEL PER ASTM A582 3. FINISH SPECIFICATIONS: STAINLESS STEEL PARTS: PASSIVATE 6. OPTICAL: WAVELENGTH: 1100nm - 1350nm INSERTION LOSS: 0.3dB TYPICAL, 0.5dB MAX RETURN LOSS: > -45dB, -50dB TYPICAL 7. REPLACEMENT KITS: CONTACT KIT: 7760-000-00709Z 8. CABLE PREPARATION AND STRIPPING PROCEDURE: CAP-E05. 9. OPTIONAL ENVIRONMENTAL BOOT 7760-000-00705Z SOLD SEPARATELY. 10. RED LDPE DUST CAP INCLUDED (NOT SHOWN) 11. CRIMP TOOLING: FOR FACTORY APPLICATION USE HAND TOOL KTH-1000 AND DIE KTH-2035 FOR FIELD APPLICATION USE HAND TOOL KTH-5000 AND DIE KTH-5018 ANGLE XXX

62 Barnes Industrial Road North

DESCRIPTION

Wallingford, Connecticut 06492 .XXXX [X.XXX] ± .XXXX ANGLES: ± 2° SCALE: 1:1 PER ASME Y14.5M-1994 UNLESS OTHERWISE SPECIFIED: DIMENSIONS ARE IN INCHES [MM] TOLERANCES: DECIMAL: .XX [X.X] ± .01 [0.3] Winchester Electronics Corporation THIRD DMF026 B 2A 1 PRE-POLISHED SHT REV OF TRI-LOC, SMPTE 304, RECEPTACLE SD7763-4-3

REPLACEMENT COMPONENT ORDERING NUMBERS 2 3 4 1 10 7 XXX KFC 01/07/10 BY DATE APPD REVISED PER ER30231 PER ASME Y14.5M-1994 UNLESS OTHERWISE SPECIFIED: DIMENSIONS ARE IN INCHES [MM] TOLERANCES: DECIMAL: .XX [X.X] ± .01 [0.3] .XXXX [X.XXX] ± .XXXX ANGLES: ± 2° SCALE: 1:1 Winchester Electronics Corporation Wallingford, Connecticut 06492 THIRD ANGLE DMF026 B A TRI-LOC, SMPTE 304, RECEPTACLE PRE-POLISHED SHT REV OF 05 2 2SD7763-4-3 CATALOG P/N: 7763-4-3 ITEM NO. PART NO. Description 7763-4- 3/QTY. PLATING CODE(S)

13 VNFPS01-900-34 SPLICE PROTECTOR SLEEVE, 34MM 50

12 VNSC-748U RED LDPE DUST CAP 25

11 7760-000-00711Z FIBER OPTIC CONNECTOR STUB 2 10 78-0102U #4-40 HEX SET SCREW 10 9 78-1012U STRENGTH MEMBER SUPPORT CLAMP 10 8 78-3011U JACK INSULATOR HALF SIDE "B" 25 7 78-3010U JACK INSULATOR HALF SIDE "A" 25 6 78-4204U JACK MALE CRIMP CONTACT 50 5 78-4203U JACK FEMALE CRIMP CONTACT 50 4 78-0705U REAR O-RING 25 3 78-0701U REAR CABLE SEAL 25 2 78-0301U WASHER FOR REAR CABLE SEAL 25 1 1-8156U CRIMP SLEEVE (CABLE SHIELD FERRULE) 25