VJ32MLCCS VISHAY | Alldatasheet

Document overview

  • Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
  • PDF pages: 21

Technical content

VJ....32 Lead-Bearing Finish MLCCs www.vishay.com Vishay Vitramon Revision: 01-Mar-2022 1 Document Number: 45256 For technical questions, contact: mlcc@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Surface Mount Multilayer Ceramic Chip Capacitors With Lead-Bearing Finish Termination

FEATURES

  • Tin / lead termination finish - minimum 4 % lead
  • Available in 0402 to 1210 body size
  • Two dielectrics
  • High operating temperature, high reliability
  • Wet build process
  • Reliable Noble Metal Electrode (NME) system
  • AEC-Q200 qualified with PPAP available
  • Custom combinations to meet specific need
  • Material categorization: fo r definitions of compliance please see www.vishay.com/doc?99912

APPLICATIONS

  • Low earth orbit satellites (LEO)
  • S p a c e
  • Aerospace
  • A v i o n i c
  • Military
  • Tin whisker mitigation ELECTRICAL SPECIFICATIONS Note (1) Under qualification; contact factory for availability C0G (NP0) DIELECTRIC (1) GENERAL SPECIFICATION Note Electrical characteristics at +25 °C unless otherwise specified Operating Temperature: -55 °C to +150 °C (above +125 °C changed characteristics) Capacitance Range: 1 pF to 15 nF Voltage Range: 25 VDC to 630 VDC Temperature Coefficient of Capacitance (TCC): 0 ppm/°C ± 30 ppm/°C from -55 °C to +125 °C Dissipation Factor (DF): 0.1 % maximum at 1.0 V RMS and

1 MHz for values ≤ 1000 pF

0.1 % maximum at 1.0 VRMS and 1 kHz for values > 1000 pF Insulating Resistance: at +25 °C 100 000 MΩ min. or 1000 ΩF whichever is less at +125 °C 10 000 MΩ min. or 100 ΩF whichever is less Aging: 0 % maximum per decade Dielectric Strength Test: performed per method 103 of EIA 198-2-E. Applied test voltages ≤ 250 V DC-rated: 250 % of rated voltage

500 VDC-rated: 200 % of rated voltage

630 VDC-rated: 150 % of rated voltage

Electrical characteristics at +25 °C unless otherwise specified Operating Temperature: -55 °C to +150 °C (above +125 °C changed characteristics) Capacitance Range: 120 pF to 1 μF Voltage Range: 16 V DC to 630 VDC Temperature Coefficient of Capacitance (TCC): ± 15 % from -55 °C to +125 °C, with 0 VDC applied Dissipation Factor (DF): 16 V, 25 V ratings: 3.5 % maximum at 1.0 VRMS and 1 kHz > 25 V ratings: 2.5 % maximum at 1.0 VRMS and 1 kHz Insulating Resistance: at +25 °C 100 000 MΩ min. or 1000 ΩF whichever is less at +125 °C 10 000 MΩ min. or 100 ΩF whichever is less Aging Rate: 1 % maximum per decade Dielectric Strength Test: performed per method 103 of EIA 198-2-E. Applied test voltages ≤ 250 V DC-rated: 250 % of rated voltage 500 VDC-rated: min. 150 % of rated voltage 630 VDC-rated: min. 120 % of rated voltage

VJ....32 Lead-Bearing Finish MLCCs www.vishay.com Vishay Vitramon Revision: 01-Mar-2022 2 Document Number: 45256 For technical questions, contact: mlcc@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Note

  • Detail ratings see “Selection Chart” Notes (1) DC voltage rating should not be exceeded in application. Other application factors may affect the MLCC performance. Consult for questions: mlcc@vishay.com (2) Consult Selection Chart table for correct dielectric code QUICK REFERENCE DATA DIELECTRIC CASE CODE MAXIMUM VOLTAGE (V) CAPACITANCE MINIMUM MAXIMUM C0G (NP0) 0402 100 1.0 pF 220 pF 0603 200 1.0 pF 820 pF 0805 500 1.0 pF 3.9 nF 1206 630 1.0 pF 8.2 nF 1210 630 100 pF 12 nF X7R 0402 100 120 pF 33 nF 0603 200 330 pF 150 nF 0805 200 330 pF 470 nF 1206 630 220 pF 1.0 μF 1210 630 390 pF 1.0 μF

ORDERING INFORMATION

CASE DIELECTRIC CAPACITANCE CAPACITANCE TERMINATION DC VOLTAGE MARKING PACKAGING PROCESS CODE NOMINAL TOLERANCE RATING (1) CODE CODE 0402 0603 0805 1206 1210 A, D = C0G (NP0) (2) Y = X7R Expressed in picofarads (pF). The first two digits are significant, the third is a multiplier. An “R” indicates a decimal point. Examples 4R7 = 4.7 pF 102 = 1000 pF B = ± 0.10 pF C = ± 0.25 pF D = ± 0.5 pF F = ± 1 % G = ± 2 % J = ± 5 % K = ± 10 % M = ± 20 % Note C0G (NP0): B, C, D < 10 pF F, G, J, K ≥ 10 pF X7R: J, K, M L = Ni barrier with tin lead plated finish min. 4 % lead J = 16 V X = 25 V A = 50 V B = 100 V C = 200 V P = 250 V E = 500 V L = 630 V A = unmarked 32 = AEC-Q200 qualified with tin / lead termination finish T = 7" reel / plastic tape C = 7" reel / paper tape J = 7" reel (low quantity) R = 11 1/4" / 13" reel / plastic tape P = 11 1/4" / 13" reel / paper tape DIMENSIONS in inches (millimeters) CASE CODE STYLE LENGTH (L) WIDTH (W) MAXIMUM THICKNESS (T) TERMINATIONS PAD (P) MINIMUM MAXIMUM 0402 VJ0402 0.040 + 0.004 / - 0.002 0.024 (0.60) 0.004 (0.10) 0.016 (0.41) 0603 VJ0603 0.063 ± 0.006 (1.60 ± 0.15) 0.031 ± 0.006 (0.80 ± 0.15) 0.038 (0.97) 0.012 (0.30) 0.024 (0.60) 0805 VJ0805 0.079 ± 0.008 (2.00 ± 0.20) 0.049 ± 0.008 (1.25 ± 0.20) 0.057 (1.45) 0.010 (0.25) 0.028 (0.71) 1206 VJ1206 0.126 ± 0.010 (3.20 ± 0.25) 0.063 ± 0.010 (1.60 ± 0.25) 0.067 (1.70) 0.010 (0.25) 0.028 (0.71) 1210 VJ1210 0.126 ± 0.010 (3.20 ± 0.25) 0.098 ± 0.010 (2.50 ± 0.25) 0.076 (1.94) 0.010 (0.25) 0.028 (0.71) L W P T

VJ....32 Lead-Bearing Finish MLCCs www.vishay.com Vishay Vitramon Revision: 01-Mar-2022 3 Document Number: 45256 For technical questions, contact: mlcc@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SELECTION CHART DIELECTRIC C0G (NP0) STYLE VJ0402 VJ0603 VJ0805 CASE CODE 0402 0603 0805 VOLTAGE (V DC) 25 / 50 100 50 100 200 50 100 200 500 VOLTAGE CODE X / A B A B C A B C E CAP. CODE CAP. Notes

  • • Paper tape, • Plastic tape These values use dielectric code “D”. All other NP0 (C0G) part numbers use dielectric code “A”

VJ....32 Lead-Bearing Finish MLCCs www.vishay.com Vishay Vitramon Revision: 01-Mar-2022 4 Document Number: 45256 For technical questions, contact: mlcc@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 122 1.2 nF •• • 152 1.5 nF •• • 182 1.8 nF • • 222 2.2 nF • 272 2.7 nF • 332 3.3 nF • 392 3.9 nF • 472 4.7 nF 562 5.6 nF 682 6.8 nF 822 8.2 nF 103 10 nF 123 12 nF 153 15 nF 183 18 nF 223 22 nF 273 27 nF 333 33 nF 393 39 nF 473 47 nF 563 56 nF Note

  • • Paper tape, • Plastic tape SELECTION CHART DIELECTRIC C0G (NP0) STYLE VJ0402 VJ0603 VJ0805 CASE CODE 0402 0603 0805 VOLTAGE (V DC) 25 / 50 100 50 100 200 50 100 200 500 VOLTAGE CODE X / A B A B C A B C E CAP. CODE CAP.

VJ....32 Lead-Bearing Finish MLCCs www.vishay.com Vishay Vitramon Revision: 01-Mar-2022 5 Document Number: 45256 For technical questions, contact: mlcc@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SELECTION CHART DIELECTRIC C0G (NP0) STYLE VJ1206 VJ1210 CASE CODE 1206 1210 VOLTAGE (V DC) 50 100 200 500 / 630 50 100 200 500 / 630 VOLTAGE CODE A B C E / L A B C E / L CAP. CODE CAP. Notes

  • • Paper tape, • Plastic tape These values use dielectric code “D”. All other NP0 (C0G) part numbers use dielectric code “A”

VJ....32 Lead-Bearing Finish MLCCs www.vishay.com Vishay Vitramon Revision: 01-Mar-2022 6 Document Number: 45256 For technical questions, contact: mlcc@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 103 10 nF • • 123 12 nF • • 153 15 nF 183 18 nF 223 22 nF 273 27 nF 333 33 nF 393 39 nF 473 47 nF 563 56 nF Note

  • • Paper tape, • Plastic tape SELECTION CHART DIELECTRIC C0G (NP0) STYLE VJ1206 VJ1210 CASE CODE 1206 1210 VOLTAGE (V DC) 50 100 200 500 / 630 50 100 200 500 / 630 VOLTAGE CODE A B C E / L A B C E / L CAP. CODE CAP.

VJ....32 Lead-Bearing Finish MLCCs www.vishay.com Vishay Vitramon Revision: 01-Mar-2022 7 Document Number: 45256 For technical questions, contact: mlcc@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SELECTION CHART DIELECTRIC X7R STYLE VJ0402 VJ0603 VJ0805 CASE CODE 0402 0603 0805 VOLTAGE (V DC) 16 25 50 100 16 25 50 100 200 16 25 50 100 200 VOLTAGE CODE J X A B J X A B C J X A B C CAP. CODE CAP. Note

  • • Paper tape, • Plastic tape

VJ....32 Lead-Bearing Finish MLCCs www.vishay.com Vishay Vitramon Revision: 01-Mar-2022 8 Document Number: 45256 For technical questions, contact: mlcc@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 124 120 nF • • • • 154 150 nF • • • • 184 180 nF •• 224 220 nF •• 274 270 nF •• 334 330 nF •• 394 390 nF • 474 470 nF • 564 560 nF 684 680 nF 824 820 nF 105 1.0 μF 125 1.2 μF 155 1.5 μF 185 1.8 μF 225 2.2 μF 275 2.7 μF 335 3.3 μF 395 3.9 μF 475 4.7 μF 565 5.6 μF 685 6.8 μF SELECTION CHART DIELECTRIC X7R STYLE VJ0402 VJ0603 VJ0805 CASE CODE 0402 0603 0805 VOLTAGE (V DC) 16 25 50 100 16 25 50 100 200 16 25 50 100 200 VOLTAGE CODE J X A B J X A B C J X A B C CAP. CODE CAP. Note

  • • Paper tape, • Plastic tape

VJ....32 Lead-Bearing Finish MLCCs www.vishay.com Vishay Vitramon Revision: 01-Mar-2022 9 Document Number: 45256 For technical questions, contact: mlcc@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SELECTION CHART DIELECTRIC X7R STYLE VJ1206 VJ1210 CASE CODE 1206 1210 VOLTAGE (V DC) 16 25 50 100 200 500 / 630 16 25 50 100 200 500 / 630 VOLTAGE CODE J X A B C E / L J X A B C E / L CAP. CODE CAP. 121 120 pF 151 150 pF 181 180 pF 221 220 pF • 271 270 pF • 331 330 pF • 391 390 pF •• 471 470 pF • • 561 560 pF •• 681 680 pF •• Note

  • Plastic tape

VJ....32 Lead-Bearing Finish MLCCs www.vishay.com Vishay Vitramon Revision: 01-Mar-2022 10 Document Number: 45256 For technical questions, contact: mlcc@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 125 1.2 μF 155 1.5 μF 185 1.8 μF 225 2.2 μF 275 2.7 μF 335 3.3 μF 395 3.9 μF 475 4.7 μF 565 5.6 μF 685 6.8 μF SELECTION CHART DIELECTRIC X7R STYLE VJ1206 VJ1210 CASE CODE 1206 1210 VOLTAGE (V DC) 16 25 50 100 200 500 / 630 16 25 50 100 200 500 / 630 VOLTAGE CODE J X A B C E / L J X A B C E / L CAP. CODE CAP. Note

  • Plastic tape

VJ....32 Lead-Bearing Finish MLCCs www.vishay.com Vishay Vitramon Revision: 01-Mar-2022 11 Document Number: 45256 For technical questions, contact: mlcc@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Notes (1) Reference: EIA standard RS 481 - “Taping of Surface Mount Components for Automatic Placement” (2) n/a = not available (3) Packaging quantity can depend from product thickness STANDARD PACKAGING QUANTITIES (1)(2) CASE CODE TAPE SIZE 7" REEL QUANTITIES 11 1/4" AND 13" REEL QUANTITIES PAPER TAPE PACKAGING CODE “C” PLASTIC TAPE PACKAGING CODE “T” LOW QUANTITY PACKAGING CODE “J” PAPER TAPE PACKAGING CODE “P” PLASTIC TAPE PACKAGING CODE “R” 0402 8 mm 5000 n/a 1000 10 000 n/a 0603 8 mm 4000 4000 1000 10 000 10 000 0805 8 mm 3000 3000 1000 10 000 10 000 1206 (3) 8 mm 3000 2500 / 3000 1000 10 000 9000 / 10 000 1210 (3) 8 mm n/a 2000 / 2500 / 3000 1000 n/a 9000 / 10 000

VJ....32 Lead-Bearing Finish MLCCs www.vishay.com Vishay Vitramon Revision: 01-Mar-2022 12 Document Number: 45256 For technical questions, contact: mlcc@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 1 - GENERAL CERTIFICATES 2 - TECHNICAL REQUIREMENTS Unless specified in component specification, these parameters are the minimum requirements for the components.

2.1 OPERATING TEMPERATURE RANGE

2.2 CHARACTERISTICS

2.3 STORAGE AND HANDLING CONDITIONS

# Quality management system according to IATF 16949 Yes # Quality management system according to ISO 9001 Yes # Environmental certification according to ISO 14001 Yes # Health and safety system according to ISO 45001 Yes For standard applications T A: -55 °C to +125 °C See characteristics 2.2 For high temperature applications T A: -55 °C to +150 °C See characteristics 2.2 For ultra high temperature applications T A: -55 °C to +175 °C See characteristics 2.2 PARAMETER CERAMIC TYPE SYMBOL RATINGS TEST CONDITIONS / REMARKS Rated voltage in temperature range -55 °C to +125 °C C0G (NP0) UR

25 V to 630 V

Derating at higher temperature up to +150 °C C0G (NP0) 25 V to 100 V U DC ≤ 1/2 UR X7R 16 V to 100 V UDC ≤ 1/2 UR UDC ≤ 1/4 UR for VJ0603Y104*A (100 nF / 50 V) Derating at higher temperature up to +175 °C C0G (NP0) 25 V to 100 V U DC ≤ 1/4 UR X7R 16 V to 100 V U DC ≤ 1/4 UR Temperature coefficient in temperature range -55 °C to +125 °C C0G (NP0) αC ≤ ± 30 ppm/°C if C R < 10 pF: αC ≤ ± 120 ppm/°C X7R ΔC + 15 % / - 30 % Temperature coefficient in temperature range -55 °C to +150 °C C0G (NP0) αC ≤ ± 30 ppm/°C if C R < 10 pF: αC ≤ ± 120 ppm/°C X7R ΔC + 15 % / - 30 % Temperature coefficient in temperature range -55 °C to +175 °C X7R ΔC + 15 % / - 50 % Dissipation factor in temperature range -55 °C to +175 °C C0G (NP0) tan δ ≤ 0.0015 X7R ≤ 0.06 (1) Store the components at 5 °C to 40 °C ambient temperature and ≤ 70 % relative humidity conditions. (2) The product is recommended to be used within a time-frame of 2 years after shipment. Check solderability in case extended shelf life beyond the expiry date is needed. Precautions: a. Do not store products in an environment containing corrosive elements, especially where chloride gas, sulfide gas, acid, alka li, salt, or the like are present. This may cause corrosion or oxidization of the terminations, which can easily lead to poor soldering. b. Store products on the shelf and av oid exposure to moisture or dust. c. Do not expose products to excessive shoc k, vibration, direct sunlight, and so on.

VJ....32 Lead-Bearing Finish MLCCs www.vishay.com Vishay Vitramon Revision: 01-Mar-2022 13 Document Number: 45256 For technical questions, contact: mlcc@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 C0G (NP0) DIELECTRIC - TYPICAL PARAMETERS 100 1000 10000 -0.6 -0.4 -0.2 0.2 0.4 0.6 -50 0 50 100 150 Temperature Dependence of Capacitance 1st line 2nd line 2nd line Capacitance Change (%) Temperature (°C) 100 1000 10000 100 1000 10 000 10 25 50 100 150 Insulation Resistance vs. Temperature 1st line 2nd line 2nd line Insulation Resistance (ΩF) Temperature (°C) 100 1000 10000 -0.2 -0.1 0.1 0.2 1 10 100 1000 10 000 Aging Rate 1st line 2nd line 2nd line Capacitance Change (%) Hours 100 1000 10000 -0.2 -0.1 0.1 0.2 0 1 02 03 04 05 06 07 08 09 0 1 0 0 Voltage Coefficient of Capacitance 1st line 2nd line 2nd line Capacitance Change (%) Applied DC Voltage (VDC) 100 1000 10000 11 0 1 0 0 1 0 0 0 Change of Capacitance with Frequency 1st line 2nd line 2nd line Capacitance Change (%) Frequency (kHz)

VJ....32 Lead-Bearing Finish MLCCs www.vishay.com Vishay Vitramon Revision: 01-Mar-2022 14 Document Number: 45256 For technical questions, contact: mlcc@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 X7R DIELECTRIC - TYPICAL PARAMETERS Note (1) Except for VJ0603Y104*A (100 nF / 50 V), see section “2.2 Characteristics” 100 1000 10000 -30 -25 -20 -15 -10 -75 -50 0 50 100 150-25 25 75 125 175 Temperature Coefficient of Capacitance 1st line 2nd line 2nd line Capacitance Change (%) Temperature (°C) 100 1000 10000 100 1000 10 000 20 40 60 80 100 120 140 160 180 Minimum Insulation Resistance vs. Temperature 1st line 2nd line 2nd line Insulation Resistance (ΩF) Temperature (°C) 100 1000 10000 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 -75 -50 -25 0 25 50 75 100 125 150 175 Dissipation Factor vs. Temperature 1st line 2nd line 2nd line Dissipation Factor (%) Temperature (°C) 100 1000 10000 1 10 100 1000 10 000 Aging Rate 1st line 2nd line 2nd line Capacitance Change (%) Hours 100 1000 10000 100 150 200 -75 -50 -25 0 25 50 75 100 125 150 175 Rated Voltage vs. Temperature (1) 1st line 2nd line 2nd line Rated Voltage (%) Temperature (°C) 100 1000 10000 -30 -25 -20 -15 -10 0 1 02 03 04 05 06 07 08 09 0 1 0 0 Voltage Coefficient of Capacitance 1st line 2nd line 2nd line Capacitance Change (%) Applied DC Voltage (VDC)

50 V rated

25 V rated

100 V rated

VJ....32 Lead-Bearing Finish MLCCs www.vishay.com Vishay Vitramon Revision: 01-Mar-2022 15 Document Number: 45256 For technical questions, contact: mlcc@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 X7R DIELECTRIC - TYPICAL PARAMETERS 100 1000 10000 0.004 0.008 0.012 0.016 0.020 0 1 02 03 04 05 06 07 08 09 0 1 0 0 Dissipation Factor vs. Voltage 1st line 2nd line 2nd line Dissipation Factor Applied DC Voltage (VDC) 50 V 100 V 100 1000 10000 0.004 0.008 0.012 0.016 0.020 0 100 200 300 400 500 600 700 Dissipation Factor vs. Voltage 1st line 2nd line 2nd line Dissipation Factor Applied DC Voltage (VDC) 200 V

500 V / 630 V

-20 -10 11 0 1 0 0 1 0 0 0 Change of Capacitance with Frequency 1st line 2nd line 2nd line Capacitance Change (%) Frequency (kHz) 100 1000 10000 11 0 1 0 0 1 0 0 0 Change of Dissipation Factor with Frequency 1st line 2nd line 2nd line Dissipation Factor (%) Frequency (kHz)

VJ....32 Lead-Bearing Finish MLCCs www.vishay.com Vishay Vitramon Revision: 01-Mar-2022 16 Document Number: 45256 For technical questions, contact: mlcc@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 3 - LOT ACCEPTANCE TESTS Process tests available in classes (on request) Upon request the records can be submitted in electronic format on monthly basis.

3.1 THERMAL STRENGTH, THERMAL SHOCK SENSIBILITY

Acceptance criteria: zero defects (IRATS and BIATS).

3.2 BOARD FLEX TEST

3.3 SOLDERABILITY / RESISTANCE TO SOLDERING HEAT

Temperature profile for reflow soldering of SMD parts IPC/JEDEC-J-STD-020C. Test is done on a regular basis for samples taken randomly out of the line. Acceptance criteria: at least 95 % new solder and no detachment or leaching of terminations. 4 - ENVIRONMENTAL REQUIREMENTS A list of the chemical substances content, which must not be used or whose use shall be limited by international law, is available on request. GROUP ACTION A Components are tested within the monitoring program of the supplier. The supplier shall submit the part numbers of the selected component to the customer during the component specification discussions. B Components (customer P/N) shall be tested quarterly. Records available only on special request by the customer. C Test with each shipment. Records are provided on a monthly basis. Customer special requirement; requirement should be determined in a specific component specification. Sample size 200 Handling Mounted on PCB Thermal shock 1 x 280 °C, no pre-heat, 5 s to 10 s IR - test (IRATS) U = UR, T = room temperature, verified Burn in (BIATS) Equivalent to 12 h burn-in, 2 x UR/125 °C, verification time to failure Sample size 20 pcs/lot Frequency At least three different part numbers of one component family matrix per quarter Max. deflection 8 mm (data to be reported, available on request)

VJ....32 Lead-Bearing Finish MLCCs www.vishay.com Vishay Vitramon Revision: 01-Mar-2022 17 Document Number: 45256 For technical questions, contact: mlcc@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 5 - INSPECTION CRITERIA The supplier shall carry out visual examin ation with suitable equipme nt with approximately 10 x magnification and lighting appropriate to the specimen under test and the required quality level. Chipping The components shall be free of cracks or fissures. Small damages which do not deteriorate the performance of the component shall be less than 50 % of the surface of the MLCC as defined in EIA 595. Delamination or Exposed Electrodes No visible separation or delamination between layers of the capacitor and no exposed electrodes between the two terminals of the capacitor must be seen. Metallization For the metallization, no visible detachment of the metallized terminals and no exposed electrodes must be seen. Defects and gaps in the metallization on each sides of the terminal must not exceed 10 % of the total area (e.g. A, B, C, …). Leaching shall not exceed 25 %. Electrode Distance The ceramic body shall be free of any conducting material between the terminals which reduces the distance of the electrodes. The minimum distance “D” is 400 μm for all package sizes, except 0402. For the component package 0402 the minimum distance is 200 μm. C A B D

VJ....32 Lead-Bearing Finish MLCCs www.vishay.com Vishay Vitramon Revision: 01-Mar-2022 18 Document Number: 45256 For technical questions, contact: mlcc@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 6 - BOARD FLEX TEST CONDITIONS

6.1 BOARD FLEX DEFINITIONS OF TEST

PCB thickness = (1.6 ± 0.1) mm Copper thickness = 35 μm Material FR4 (EP-GC 02 according to DIN 40 802) Note

  • LL = total length; LB = width of the pad; LEL = single pad length

6.2 SOLDERING INSTRUCTIONS

6.3 TYPICAL TEMPERATURE PROFILE FOR REFLOW SOLDERING (Boardflex test)

LAYOUT / PAD DESIGN (Dimensions in mm) CASE CODE PAD SIZE LL LB LEL 0603 2.20 1.00 0.75 0805 3.40 1.30 1.20 1206 4.50 1.80 1.20 1210 4.50 2.80 1.30 THICKNESS, RECOMMENDED FOR SOLDER PASTE (Reflow soldering) CASE CODE THICKNESS in μm 0402 75 to 90 0603 150 to 200 0805 150 to 200 1206 150 to 200 1210 150 to 200 LEL LL LB TEMPERATURE (°C) 300 250 200 150 100 0 50 100 150 200 250 300 350 400 TIME (s) LEAD (Pb)-FREE SOLDERING PROFILE MIN. 300 s MAX. 260 °C MIN. 255 °C T (SOLID) MIN. 217 °C MIN. 190 °C MIN. 40 s MIN. 90 s RAMP UP TO 150 °C MAX. 3 K/s RAMP DOWN FROM T (SOLID) MAX. 6 K/s MIN. 110 s50

VJ....32 Lead-Bearing Finish MLCCs www.vishay.com Vishay Vitramon Revision: 01-Mar-2022 19 Document Number: 45256 For technical questions, contact: mlcc@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

6.4 MOUNTING, DIMENSIONS, AND TESTING

6.5 PERFORMANCE OF THE TEST(S)

A) Electrical test according to component specification (Cap, DF, IR) B) Mounting to PCB C) Storage at room temperature (min. 10 h) D) Board flex test

6.6 DETAILS

6.7 FAILURE CRITERIA

X7R PCB to be deflected continuously, speed 1 mm/s (± 0.5 mm/s) C0G PCB to be deflected in steps until cracks or other damages are visible or can be measured. Dwell time between steps: (5 ± 1) s X7R Piezoelectric sensor, no failure up to min. 2 mm C0G (NP0) ΔC/C < 1 % or < 1 pF, no failure up to min. 2 mm Both Electrical test according to component specification SMD under test Solder Support 1.6 ± 0.1 90 ± 1 45 ± 2 Printed board before test R = 3 + + Material: aluminum20 Printed board during test Width = actual width of substrate + 5 mm on both sides Radius 1 to 2 Width Displacement D = min. 2 mm All dimensions in mm 10 ± 0.1

VJ....32 Lead-Bearing Finish MLCCs www.vishay.com Vishay Vitramon Revision: 01-Mar-2022 20 Document Number: 45256 For technical questions, contact: mlcc@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 7 - QUALIFICATION TESTING NO. TEST ITEM REFERENCE

1 Pre- and post stress electrical test User spec

3 High temp exposure (stora ge) MIL-STD-202, method 108

4 Temperature cycling JESD22, method JA-104

5 Destructive physical analysis EIA-469

6 Moisture resistance MI L-STD-202, method 106

7 Biased humidity MIL-STD-202, method 103

8 Operation life MIL-STD-202 method 108

9 External Visual MIL-STD-883 method 2009

10 Physical dimension J ESD22, method JB-100

13 Mechanical shock MIL-STD-202, method 213

14 Vibration MIL-STD-202, method 204

15 Resistance to solder heat MIL-STD-202, method 210

16 ESD AEC-Q200-002

17 Solderability J-STD-002

21 Board flex AEC-Q200-005

22 Terminal strength AEC-Q200-006

23 Beam load AEC-Q200-003

www.vishay.com Vishay Revision: 01-Jan-2023 1 Document Number: 91000 Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA AR E SUBJECT TO CHANGE WITH OUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product , (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all implied warranties, incl uding warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of pro ducts for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in ge neric applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specificat ions may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and for informational purposes only. Inclusion of these hyperlinks does not constitute an endorsement or an approval by Vishay of any of the products, services or opinions of the corporation, organization or individual associated with the third-party website. Vishay disclaims any and all liability and bears no responsibility for the accuracy, legality or content of the third-party web site or for that of subsequent links. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. © 2023 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED