VCS1026 CTS | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 4

Technical content

622.080MHz VCSO Document No. VCS1026 06/28/2007 Page 1 - 4 Rev. A ٠ ٠ ٠CTS Electronic Components, Inc. ٠171 Covington Drive ٠Bloomingdale, IL 60108 ٠ ٠ ٠ ٠ ٠ ٠www.ctscorp.com ٠ ٠ ٠

FEATURES

  • Industry Standard 5x7mm SMT Footprint
  • +3.3 Vdc Supply Voltage
  • -40°C to 85°C Temp. Range
  • LVPECL differential outputs
  • ± 50ppm Absolute Pull Range (APR)
  • Output Enable/Disable Function
  • SAW resonator
  • Extremely Low Jitter
  • Tape & Reel Packaging
  • RoHS Compliant

DESCRIPTION

Surface mount 5x7mm VCSO operating at 3.3V supply with complementary LVPECL outputs for use in datacom & telecom applications. ELECTRICAL SPECIFICATIONS Parameter Conditions & Remarks Min Typical Max Unit Operating Conditions Nominal Frequency fNOM - 622.080 - MHz Operating Temperature Range -40 - 85 °C Storage Temperature Range -55 - 125 °C Supply Voltage VCC; ±5% 3.135 3.300 3.465 Vdc Supply Current Icc; Max. VCC; TA = 25°C load = 50Ω to VCC – 2V - 60 70 mA Load output to VCC – 2V - 50 - Ω Frequency Stability Frequency vs. Temperature ref to TA = 25°C; VC = constant +20 - -150 ppm Electronic Frequency Control Input Impedance Zi 50 100 - kΩ Control Voltage Range VC ; positive monotonic transfer 0.3 - 3.0 Vdc Gain Transfer - 180 - ppm/V Absolute Pull Range APR; all causes (see note 1) ± 50 - - ppm Modulation Bandwidth -3dB ref. 100Hz - 50 - kHz Linearity Deviation from best linear fit - 2 10 % NOTE 1: Minimum guaranteed frequency shift (∆f/fNOM) under all conditions (temperature, aging, supply voltage, load) for 15 years at an average effective operating temperature of +55°C

622.080MHz VCSO Document No. VCS1026 06/28/2007 Page 2 - 4 Rev. A ٠ ٠ ٠CTS Electronic Components, Inc. ٠171 Covington Drive ٠Bloomingdale, IL 60108 ٠ ٠ ٠ ٠ ٠ ٠www.ctscorp.com ٠ ٠ ٠ ELECTRICAL SPECIFICATIONS (Continued) Parameter Conditions & Remarks Min Typical Max Unit Output Parameters Output Signal LVPECL VOL - - VCC-1.620 Amplitude VOH VCC-1.025 - - Vdc Rise/Fall Times 20% to 80% - 250 400 ps Duty Cycle @ 50% of output signal 45 50 55 % Start up time to reach 90% of final amplitude - - 10 ms 100Hz - -85 -75 dBc/Hz 1kHz - -110 -100 dBc/Hz 10kHz - -140 -130 dBc/Hz 100kHz - -143 -140 dBc/Hz Phase Noise 1MHz - -143 -140 dBc/Hz 12kHz to 20MHz (calculated from Phase Noise) - 0.16 0.3 ps RMS Phase Jitter 50kHz to 80MHz (calculated from Phase Noise) - 0.16 0.3 ps RMS LVPECL OUTPUT WAVEFORM TEST CIRCUIT, LVPECL LOAD OUTPUT ENABLE/DISABLE LOGIC Pad 2 Pad 4 Pad 5 Low ”0” outputs disabled HI Z HI Z Open outputs enabled Output Comp. Output High ”1” outputs enabled Output Comp. Output

622.080MHz VCSO Document No. VCS1026 06/28/2007 Page 3 - 4 Rev. A ٠ ٠ ٠CTS Electronic Components, Inc. ٠171 Covington Drive ٠Bloomingdale, IL 60108 ٠ ٠ ٠ ٠ ٠ ٠www.ctscorp.com ٠ ٠ ٠ MECHANICAL SPECIFICATIONS PACKAGE DRAWING PIN 1 PIN 2 PIN 3 PIN 6 PIN 5 PIN 4 VCS1026 CTS YYWW 5.18±0.10 [.204±.004] 7.52±0.10 [.296±.004] 5.08 [.200] 2.54 [.100] 2.68 [.105] 1.27 [.050] 1.90 [.075] PIN 1 PIN 2 PIN 3 PIN 6P IN 5P IN 4 BARRIER COVERING OVER RESIST MASK OVER GROUND PLANE MAX TYP PIN #1 MARK 1.68 [.066] 1.47 [.058] 1.47 [.058] 1.68 [.066] 0.56 [.022] EXPOSED GROUND PLANE AND COVER CASTELLATION

2 PLACES

TYP 1.27 [.050] TYP Lead Termination Finish: Gold flash, <10 micro inch, over 100 micro inch minimum Ni plated Cu Co-Planarity (from seating plane): 0.1 [0.004] maximum Dimensions in mm and [inches] 1) Control Voltage - VC 2) Enable/Disable Control 3) Ground/Case 4) Output 5) Complementary Output 6) Supply Voltage - VCC

622.080MHz VCSO Document No. VCS1026 06/28/2007 Page 4 - 4 Rev. A ٠ ٠ ٠CTS Electronic Components, Inc. ٠171 Covington Drive ٠Bloomingdale, IL 60108 ٠ ٠ ٠ ٠ ٠ ٠www.ctscorp.com ٠ ٠ ٠ SUGGESTED SOLDER PAD GEOMETRY 3.83 [.151] 1.68 [.066] 5.08 [.200] 2.54 [.100] 1.70 [.067] 2.34 [.092] 5.54 [.218] Dimensions are in mm and [inches]. MAXIMUM SOLDERING PROFILE Temperature 217°C 260°C (Absolute max temperature) Time 60-150 sec 10 sec. max Note: Part is not designed to be reflowed in an inverted position. TAPE AND REEL INFORMATION DIRECTION OF FEED Ø23 Ø180Ø60 17.5 120° Ø13 2.0 8.00 4.00 7.80 7.60 5.60 5.40 16.00 1.75 7.50 Ø1.50 3.10 2.90 DIMENSIONS ARE IN MM Device quantity is 1000 pieces max. per 180mm reel. MSL Level: 1 This product is fully compliant to RoHS Directive 2002/95/EC