V23026E1106B201

V23026 MACOM | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 10

Technical content

Rev. C EC-JM00-0009-03 ECOC: JM10 1. Aug. 04

1 pole telecom and signal relay, polarized, Through Hole Type (THT) or Surface Mount Technology (SMT), Relay types: non-latching with 1 coil latching with 2 coils latching with 1 coil

Features

– Directly triggerable with TTL standard modules such as ALS, HCT and ACT – Slim line 13.5 x 7.85 mm, 0.531 x 0.309 inch – Switching current 1 A – 1 changeover contact (1 form C / SPDT) – Bifurcated contacts – Immersion cleanable – High sensitivity results in low nominal power consumption 65 to 130 mW for non-latching 30 to 150 mW for latching – Surge voltage resistance between contact and coil: - 2.5 kV (2 / 10 µsec) meets the Bellcore Requirement GR-1089 - 1.5 kV (10 / 160 µsec) meets FCC Part 68 Typical applications – Automotive equipment CAN bus, imobilizer – Office equipment – Measurement and control equipment – Medical equipment – Safety equipment Options – FCC version on request. Testing of open contacts with surge voltage in accordance with FCC 68.302 (1.5 kV, 10/160 µsec) P1 Relay V23026 Basic insulation coil/contacts according to IEC/EN 60950 Clearance > 0.75 mm Creepage distance > 0.75 mm UL File No. E 111441 Page 2 (10) 108-98009 Rev. C European Directive conformance: P1 relay product conformance according to: - Directive 2000/53/EC: ELV (End of Life of Vehicles) - Directive 2002/95/EC: ROHS (Restrictions of the use of certain hazardous substances in electrical and electronic equipment) Compliance is evidenced by written declaration from all raw material suppliers. Tyco Electronics AXICOM only has responsibility for the proper processing of these materials. Confirmation is valid for date codes ≥ 0429

T 3.5 - 0.2 0.138 -0.008 N/A N/A T1 N/A N/A 10.9 - 0.5 0.429 - 0.020 S 0.3 ± 0.1 0.012 ±0.004 N/A N/A S1 N/A N/A 0.85 ± 0.1 0.033 ±0.004 S2 N/A N/A 0.2 - 0.15 0.008 ±0.006 P1 Relay V23026 Terminal assignment Relay - top view Mounting hole layout View onto the component side of the PCB Solder pad layout View onto the component side of the PCB Contact release or reset condition, coil polarity to set the relay THT Version SMT Version Latching type, 2 coils reset condition Non-latching type, not energized condition Latching type, 1 coil reset condition Page 3 (10) 108-98009 Rev. C Contacts are shown in reset condition. Both coils can be used either as set or reset coil.

3 2.25 8.80 0.30 66 137 V23026A1006B201 1-1393774-7 5 3.75 14.50 0.50 68 370 V23026A1001B201 0-1393774-1 9 6.75 25.50 0.90 70 1165 V23026A1005B201 1-1393774-5 12 9.00 35.00 1.20 64 2250 V23026A1002B201 0-1393774-2 24 18.00 50.00 2.40 128 4500 V23026A1004B201 1-1393774-2 3 2.25 8.00 0.30 80 113 V23026D1026B201 0-1393776-8 5 3.75 13.30 0.50 80 313 V23026D1021B201 0-1393776-3 9 6.75 24.00 0.90 80 1015 V23026D1025B201 0-1422015-9 12 9.00 35.00 1.20 80 1800 V23026D1022B201 0-1393776-4 24 18.00 50.00 2.40 128 4500 V23026D1024B201 0-1393776-7 3 2.25 13.00 2.25 30 300 V23026C1056B201 2-1393774-6 5 3.75 20.00 3.75 34 740 V23026C1051B201 2-1393774-0 9 6.75 35.00 6.75 38 2160 V23026C1057B201 2-1393774-7 12 9.00 50.00 9.00 32 4500 V23026C1052B201 2-1393774-1 24 18.00 50.00 18.00 128 4500 V23026C1054B201 2-1393774-4 3 2.25 8.55 2.25 69 130 V23026B1106B201 0-1393775-3 5 3.75 14.75 3.75 64 390 V23026B1101B201 3-1393774-4 9 6.75 26.00 6.75 68 1200 V23026B1105B201 0-1393775-2 12 9.00 29.00 9.00 96 1500 V23026B1102B201 3-1393774-5 24A nominal voltage of 24 V is feasible with a 12 V coil with a series resistor (1500 W) THT, non-latching, 1 coil Further coil versions e.g. 1.5 V, 9 V and 15 V are available on request. P1 Relay V23026 THT, latching, 2 coils (coils I and II are identical) THT, latching, 1 coil SMT, non-latching, 1 coil 3 2.25 8.55 2.25 69 130 V23026E1106B201 0-1393777-3 5 3.75 14.75 3.75 64 390 V23026E1101B201 0-1422015-6 9 6.75 26.00 6.75 68 1200 V23026E1105B201 0-1393777-2 12 9.00 29.00 9.00 96 1500 V23026E1102B201 0-1393776-9 24A nominal voltage of 24 V is feasible with a 12 V coil with a series resistor (1500 W) SMT, latching, 2 coils (coils I and II are identical) 5 3.75 20.00 3.75 34 740 V23026F1051B201 0-1422015-8 12 9.00 50.00 9.00 32 4500 V23026F1052B201 4-1393774-3 24A nominal voltage of 24 V is feasible with a 12 V coil with a series resistor (4500 W) SMT, latching, 1coil Page 4 (10) 108-98009 Rev. C Coil Data (values at 23°C) Nominal Operate/set voltage range Release/ Coil Coil Relay Tyco part voltage reset voltage power Resistance code number Unom Minimum Minimum Maximum voltage Umin voltage Umax Vdc Vdc Vdc Vdc mW Ω / ± 10 %

Ordering Information

Umax. at 0 A Umax. at - 1 A Unom. nominal coil voltage Uop. min. Urel. min. Ambient Temperature [°C] Coil Voltage [U/Unom] Umax. at 0 A 65 mW 130 mW

Uset min. Ambient Temperature [°C] Coil Voltage [U/Unom] Unom. nominal coil voltage Umax. - 100 % coil duty at 0 A 65 mW Latching 32 mW LatchingUmax. - 5 % coil duty at 1 A Umax. - 5 % coil duty at 0 A Max. DC load breaking capacity P1 Relay V23026 Page 5 (10) 108-98009 Rev. C Number of contacts and type Contact assembly Contact material Limiting continuous current at max. ambient temperature Maximum switching current Maximum swichting voltage Maximum switching capacity Thermoelectric potential Initial contact resistance / measuring condition: 10 mA / 20 mV Electrical endurance at 12 V / 10 mA at 6 V / 100 mA at 30 V / 1000 mA Mechanical endurance UL/CSA ratings 1 changeover contact Bifurcated contact Palladium nickel, gold-rhodium covered 1 A 1 A

125 Vdc

150 Vac

30 W, 60 VA

< 100 mV < 50 mW typ. 5 x 107 operations typ. 1 x 107 operations typ. 1 x 104 operations typ. 109 operations

30 Vdc / 1 A

65 Vdc / 0.46 A 150 Vac / 0.46 A Contact Data Unom = Nominal coil voltage Umax. = Upper limit of the operative range of the coil voltage (limiting voltage) when coils are continously energized Uop. min. = Lower limit of the operative range of the coil voltage (reliable operate voltage) Urel. min. = Lower limit of the operative range of the coil voltage (reliable release voltage)

Insulation resistance at 500 VDC Dielectric test voltage (1 min) between coil and contacts (Relay with 1 coil) between open contacts Surge voltage resistance according to Bellcore TR-NWT-001089 (2 / 10 ms) between coil and contacts (Relay with 1 coil) between open contacts according to FCC 68 (10 / 160 ms) between coil and contacts (Relay with 1 coil) between open contacts Insulation according to IEC / EN 60950 Clearance Creepage distance > 109 W

1500 Vrms

500 Vrms

0.75 mm 0.75 mm P1 Relay V23026 Capacitance between coil and contacts between open contacts RF Characteristics Isolation at 100 / 900 MHz Insertion loss at 100 / 900 MHz V.S.W.R. at 100 / 900 MHz max. 6 pF max. 5 pF - 30.0 dB / - 18.0 dB - 0.12 dB / - 1.9 dB 1.06 / 1.75 High Frequency Data Insulation Page 6 (10) 108-98009 Rev. C General data Operate time at Unom typ. / max. Reset time (latching) at Unom , typ. / max. Release time without diode in parallel (non-latching), typ. / max. Release time with diode in parallel (non-latching), typ. / max. Bounce time at closing contact, typ. / max. Maximum switching rate without load Ambient temperature Thermal resistance Maximum permissible coil temperature Vibration resistance (function) Shock resistance, half sinus, 11 ms Degree of protection / Environmental protection Needle flame test Mounting position Processing information Weight (mass) Terminal surface Resistance to soldering heat 1 ms / 2 ms 1 ms / 2 ms 0.4 ms / 1 ms 1.2 ms / 2 ms 1 ms / 3 ms 200 operations/s -40° C ... +70° C, +85° C on request < 130 K/W 85° C

20 G, 200 to 2000 Hz

40 G, 10 to 200 Hz

50 G (function)

immersion cleanable, IP 67 / RT III application time 20 s, burning time < 15 s any Ultrasonic cleaning possible max. 2 g SnCu 0.7 260° C / 10 s All data refers to 23° C unless otherwise specified.

Recommended soldering conditions Soldering conditions according CECC 00802 Vapor Phase Soldering: Temperature/Time Profile (Lead Temperature) Infrared Soldering: Temperature/Time Profile (Lead Temperature) Full line: typical Dotted line: process limits 10 sec ca. 40 sec max. 235° C 200° C 130° C 180° C Time (s) 215° C 180° C 130° C 100° C external preheating 20 - 40 sec Full line: typical Dotted line: process limits forced cooling Time (s) Temperature °C Temperature °C Note: Internal relay termperature should not exceed 210° C Page 7 (10) 108-98009 Rev. C

Tube for THT version - 40 relays per tube, 2000 relays per box Tape and reel for SMT version - 480 relays per reel, 2400 per box Reel dimension Packing Dimensions in mm Page 8 (10) 108-98009 Rev. C

4th generation slim line – low profile polarized 2 c/o telecom relay with bifurcated contacts, available as non latching or latching relay with of 140... 200 mW, latching relays with 1 coil 100 mW. The IM relay is available as through hole and surface mount type (J-Legs and Gull Wings) and capable to switch loads up to 60 W/62,5 VA. Dielectric strength fulfills the Bellcore requirements according GR 1089 (2,5 kV – 2 / 10 µs) and FCC part 68 (1,5 kV – 10 / 160 µs). The IM relay is CECC/IECQ approved and certified in accordance with IEC/EN 60950 and UL1950. Dimensions approx. 10 x 6 mm board space and 5.65 mm height. P2 Relays 3rd generation polarized 2 c/o telecom relay with bifurcated contacts, available as non latching or latching relay with 1 or 2 coils. Nominal voltage range from 3 ... 24 V, coil power consumption 140 mW, latching relays with 1 coil 70 mW. The P2 Relay is available as through hole or surface mount type and capable to switch currents up to 5 A. Dielectric strength fulfills the Bellcore requirements according GR 1089 (2,5 kV – 2 / 10 µs) and FCC part 68 (1,5 kV – 10 / 160 µs). Dimensions approx. 15 x 7,5 mm board space and 10 mm height. FX Relays 3rd generation polarized 2 c/o telecom relay with bifurcated contacts, available as non latching or latching relay with 1 coil. Nominal voltage high sensitive version, 140... 300 mW for the standard version, latching relays with 1 coil 100 mW. The FX2 relay is available as through hole type and capable to switch loads up to 60 W/62,5 VA. Dielectric strength fulfills the Bellcore requirements according GR 1089 (2,5 kV – 2 / 10 µs) and FCC part 68 (1,5 kV – 10 / 160 µs). The FX2 is CECC/ IECQ approved and certified in accordance with IEC/EN 60950 and UL1950. Dimensions approx. 15 x 7,5 mm board space and 10,7 mm height. FT2 / FU2 Relays 3rd generation non polarized, non latching 2 c/o telecom relay with bifurcated contacts. Nominal voltage range from 3 ... 48 V, coil power through hole and surface mount type. Dielectric strength fulfills the Bellcore requirements according GR 1089 (2,5 kV – 2 / 10 µs) and FCC part 68 (1,5 kV – 10 / 160 µs). The FT2/FU2 is CECC/IECQ approved and certified in accordance with IEC/EN 60950 and UL1950. Dimensions approx. 15 x 7,5 mm board space and 10 mm height. FP2 Relays 3rd generation polarized 2 c/o telecom relay with bifurcated contacts, available as non latching or latching relay with 1 or 2 coils. Nominal for the high sensitive version, 140... 300 mW for the standard version, latching relays with 1 coil 100 mW.. The FP2 Relay is available as through hole type and capable to switch loads up to 30 W/62,5 VA. Dielectric strength fulfills FCC part 68 (1,5 kV – 10 / 160 µs). The FP2 is CECC/IECQ approved. Dimensions approx. 14 x 9 mm board space and 5 mm height. MT2 / MT4 2nd generation non polarized, non latching 2 c/o and 4 c/o telecom and

48 V, coil power consumption 150/200/300/400 and

550 mW, and 300 mW (MT4). Dielectric strength fulfills the requirements according FCC part 68 (1,5 kV – 10 / 160 µs) for both and the Bellcore requirements according GR 1089 (2,5 kV – 2 / 10 µs) the MT4 only. Dimensions MT2 approx. 20 x 10 mm board space and 11 mm height, MT4 approx. 20 x15 mm board space and 11 mm height. D2n Relays 2nd generation non polarized 2 c/o relay for telecom and various other applications. Nominal voltage range from 3 ... 48 V, coil power switch currents up to 3 A. Dielectric strength fulfills the requirements according FCC part 68 (1,5 kV – 10 / 160 µs). Dimensions approx. 20 x10 mm board space and 11,5 mm height. P1 Relays Extremely sensitive, polarized 1 c/o relay with bifurcated contacts for a wide range of applications, available as non latching or latching relay with 1 or 2 coils. Nominal voltage range from 3 ... 24 V, coil power consumption 65 mW, latching relays with 1 coil 30 mW. The P1 relay is available as through hole or surface mount type and capable to switch currents up to 1 A. Dielectric strength fulfills the requirements according FCC part 68 (1,5 kV – 10 / 160 µs). Dimensions approx. 13 x 7,6 mm board space and 7 mm height for THT or 8 mm height for SMT version. W11 Relays Low cost, non polarized 1 c/o relay for various applications. Nominal voltage range from 3 ... 24 V, coil power consumption 450 mW, sensitive versions 200 mW. The W11 relay is capable to switch currents up to 3 A. Dielectric strength 1000 Vrms. Dimensions approx. 15,6 x 10,6 mm board space and 11,5 mm height. Reed Relays High sensitive, non polarized relay for telecom and various other applications, available with 1 n/o, 2 n/o or 1c/o contacts. Nominal for 1 n/o and 125 ... 280 mW for 2 n/o or 1 c/o versions. Reedrelays are available in DIP or SIL housing and capable to switch currents up to 0,5 A. Integrated diode and/or electrostatic shield optional. Dielectric strength 1500 Vdc. Dimensions approx. 19,3 x 7 mm board space and 5 ... 7,5 mm height for DIP or 19,8 x 5 mm board space and 7,8 mm height for SIL version. Cradle Relays Extremely reliable and mature relay family of 1st generation for various signal switching applications. Available as non polarized, polarized / latching and relay with AC coil. The benefit is the possibility of combining various contact sets from 1 up to 6 poles, single and bifurcated contacts, different contact materials with a coil voltage range from 1,5 Vdc to 220 Vac. Cradle relays are available as dust protected and hermetically sealed versions, with plug in or solder terminals and are capable to switch currents up to 5 A. Forcibly guided (linked) contact sets optional. Dielectric strength 500 Vrms. Dimensions from approx. 19 x 24 to 19x35 mm board space and 30 mm height. Other Relays We offer a variety of different relay families for maintenance and replacement purposes. These relays are up to 60 years old now, such as Card Relay SN (V23030 / V23031 series), Small General Purpose Relay (V23006 series), Small Polarized Relay (V23063 ... V23067 and V23163 ... V23167 series). Accessories like sockets, hold down springs, etc. optional. HF3 Relay High performance low cost RF relay with excellent RF characteristics. Available with an impedance of 50 and 75 Ohm. Suitable for frequen- cies up to 3 GHz. Actually smallest RF relay available combining small size, excellent RF performance and SMD solderability. Available as non latching or latching relay with 1 or 2 coils and a nominal coil voltage range from 3 ... 24 V, coil power consumption 140 mW, latching relays with 1 coil 70 mW. Dimensions 14.6 x 7.3 x 10 mm. Page 9 (10) 108-98009 Rev. C

Tyco Electronics AXICOM Ltd. Seestrasse 295 - P.O. Box 220 CH-8804 Au-Wädenswil / Switzerland Phone +41 1 782 9111 Fax +41 1 782 9080 E-mail: axicom@tycoelectronics.com Tyco Electronics Corporation POB 3608, Harrisburg, PA 17105, USA Phone +001 800-522-6752 Tyco Electronics EC Trutnov s.r.o. Komenského 821 CZ-541 01 Trutnov / Czech Republic E-mail: axicom@tycoelectronics.com Page 10 (10) 108-98009 Rev. C Tyco Electronics Paulsternstrasse 26 D-13629 Berlin / Germany Phone +49 30 386 38573 Fax +49 30 386 38575 E-mail: axicom@tycoelectronics.com