AUML LITTELFUSE | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 9
Technical content
Features
- Load Dump Energy Rated per SAE Specification J1113
- Leadless, Surface Mount Chip Form
- “Zero”Lead Inductance
- Variety of Energy Ratings Available
- No Temperature Derating up to 125oC Ambient
- High Peak Surge Current Capability
- Low Profile, Compact Industry Standard Chip Size; (1206, 1210, 1812 and 2220 Sizes)
- Inherent Bidirectional Clamping
- No Plastic or Epoxy Packaging Assures Better than 94V-0 Flammability Rating
at these or any other conditions above those indicated in the operational sections of this specification is not implied.
- Load dump energy rating (into the suppressor) of a voltage transient with a resultant time constant of 115ms to 230ms.
- Thermal shock capability per Mil-Std-750, Method 1051: -55
oC to 125oC, 5 minutes at 25oC, 25 Cycles: 15 minutes at each extreme.
- For application specific requirements, please contact Littelfuse.
For automotive 24V and 42V applications please contact your Littelfuse representative or visit www.littelfuse.com for the latest product update. FIGURE 1. CURRENT, ENERGY AND POWER DERATING
Multilayer Transient Voltage Surge Suppressor 161www.littelfuse.com 3SURFACE MOUNT VARISTORS Load Dump Energy Capability A Load dump transient occurs when the alternator load in the automobile is abruptly reduced. The worst case scenario of this transient occurs when the battery is disconnected while operating at full rated load. There are a number of different load dump specifications in existence in the automotive industry, with the most common one being that recommend- ed by the Society of Automotive Engineers, specification #SAE J1113. Because of the diversity of these load dump specifications Littelfuse defines the load dump energy capability of the AUML suppressor range as that energy dissipated by the device itself, independent of the test circuit setup. The resultant load dump energy handling capability serves as an excellent figure of merit for the AUML suppressor. Standard load dump specifications require a device capability of 10 pulses at rated energy, across a temperature range of -40 oC to 125oC. This capability requirement is well within the ratings of all of the AUML series (Figure 5). Further testing on the AUML series has concentrated on extending the number of load dump pulses, at rated energy, which are applied to the devices. The reliability information thus generated gives an indication of the inherent capability of these devices. As an example of device durabil- ity the 1210 size has been subjected to over 2000 pulses at its rated energy of 3 joules; the 1812 size has been pulsed over 1000 times at 6 joules and 2220 size has been pulsed at its rated energy of 25 joules over 300 times. In all cases there has been little or no change in the device characteristics (Figure 6). The very high energy absorption capability of the AUML suppressor is achieved by means of a highly controlled manufacturing process. This technology ensures that a largevolume of suppressor material, with an interdigitated layer construction, is available for energy absorption in an extremely small package. Unlike equivalent rated silicon TVS diodes, the entire AUML device volume is available to dissipate the load dump energy. Hence, the peak temperatures generated by the load dump transient are sig- nificantly lower and evenly dissipated throughout the complete device (Figure 4). This even energy dissipation ensures that there are lower peak tempera- tures generated at the P-N grain boundaries of the AUML suppressor. There are a number of different size devices available in the AUML series, each one with a load dump energy rating, which is size dependent. Experience has shown that while the effects of a load dump transient is of real concern, its frequency of occurrence is much less than those of low energy inductive spikes. Such low energy inductive spikes may be generated as a result of motors switching on and off, from ESD occur- rences, fuse blowing, etc. It is essential that the suppression technology selected also has the capability to suppress such transients. Testing on the V18AUMLA2220 has shown that after being subjected to a repetitive energy pulse of 2 joules, over 6000 times, no characteristic changes have occurred (Figure 7.) Speed of Response The clamping action of the AUML suppressor depends on a conduction mechanism similar to that of other semiconductor devices (i.e. P-N Junctions). The apparent slow response time often associated with transient voltage suppressors (Zeners, MOVs) is often due to parasitic inductance in the package and leads of the device and less dependent of the basic material (silicon, zinc oxide). Thus, the single most critical element affecting the response time of any suppressor is its lead induc- tance. The AUML suppressor is a surface mount device, with no leads or external packaging, and thus, it has virtually zero inductance. The actual response time of a AUML surge suppressor is in the 1 to 5 nanosecond range, more than sufficient for the transients which are likely to be encountered in an automotive environment.
Multilayer Transient Voltage Surge Suppressor AUML Varistor Series Surface Mount Varistors 162 www.littelfuse.com
Multilayer Transient Voltage Surge Suppressor 163www.littelfuse.com 3SURFACE MOUNT VARISTORS Soldering Recommendations The principal techniques used for the soldering of components in surface mount technology are Infra Red (IR) Reflow, Vapour Phase Reflow, and Wave Soldering. When wave soldering, the suppressor is attached to the circuit board by means of an adhesive. The assembly is then placed on a conveyor and run through the soldering process to contact the wave. With IR and Vapour Phase Reflow, the device is placed in a solder paste on the substrate. As the solder paste is heated, it reflows and solders the unit to the board. The recommended solder is a 62/36/2 (Sn/Pb/Ag), 60/40 (Sn/Pb), or 63/37 (Sn/Pb). Littelfuse also recommends an RMA solder flux. Wave soldering is the most strenuous of the processes. To avoid the possibility of generating stresses due to thermal shock, a preheat stage in the soldering process is recommended, and the peak temperature of the solder process should be rigidly controlled. When using a reflow process, care should be taken to ensure that the chip is not subjected to a thermal gradient steeper than 4 degrees per second; the ideal gradient being 2 degrees per second. During the soldering process, preheating to within 100 degrees of the solders peak temperature is essential to minimize thermal shock. Examples of the soldering condi- tions for the AUML Series of suppressors are given in the tables below. Once the soldering process has been completed, it is still necessary to ensure that any further thermal shocks are avoided. One possible cause of thermal shock is hot printed circuit boards being removed from the solder process and subjected to cleaning solvents at room temperature. The boards must be allowed to gradually cool to less than 50 oC before cleaning. Termination Options Littelfuse offers two types of electrode termination finish for the Multilayer product series: 1. Silver/Platinum (standard) 2. Silver/Palladium (optional)
Multilayer Transient Voltage Surge Suppressor AUML Varistor Series Surface Mount Varistors 164 www.littelfuse.com Explanation of Terms Maximum Continuous DC Working Voltage (VM(DC)) This is the maximum continuous DC voltage which may be applied, up to the maximum operating temperature (125oC), to the ML suppressor. This voltage is used as the reference test point for leakage current and is always less than the breakdown voltage of the device. Load Dump Energy Rating (WLD) This is the actual energy the part is rated to dissipate under load dump conditions (not to be confused with the “source energy”of a load dump test specification). Maximum Clamping Voltage (VC) This is the peak voltage appearing across the suppressor when meas- ured at conditions of specified pulse current and specified waveform (8/20µs). It is important to note that the peak current and peak voltage may not necessarily be coincidental in time. Leakage Current (IL) In the nonconducting mode, the device is at a very high impedance (approaching 106Ω at its rated working voltage) and appears as an almost open circuit in the system. The leakage current drawn at this level is very low (<25µA at ambient temperature) and, unlike the zener diode, the multilayer TVS has the added advantage that, when operated up to its maximum temperature, its leakage current will not increase above 500µA. Nominal Voltage (VN(DC)) This is the voltage at which the AUML enters its conduction state and begins to suppress transients. In the automotive environment this voltage is defined at the 10mA point and has a minimum (V N(DC) MIN) and maximum (VN(DC) MAX) voltage specified. Mechanical Dimensions Recommended Pad Outline D E W L
Multilayer Transient Voltage Surge Suppressor 165www.littelfuse.com 3SURFACE MOUNT VARISTORS
Ordering Information
Standard Shipping Quantities V 18 AUML A 2220 X X AUML SERIES PACKING OPTIONS END TERMINATION OPTION DEVICE SIZE LOAD DUMP ENERGY RATING INDICATOR AUTOMOTIVE MULTILAYER DESIGNATOR MAXIMUM DC WORKING VOLTAGE DEVICE FAMILY A: 2500 pc. Bulk Pack H: 7in (178mm) Diameter Reel (Note) T: 13in (330mm) Diameter Reel (Note) No Letter: Ag/Pt (Standard) W: ag/Pd N: Ni/Sn (up to 1210 only) i.e., 220 mil x 200 mil Note: See quantity table TVSS Devise Tape and Reel Specifications
- Conforms to EIA - 481, Revision A
- Can be Supplied to IEC Publication 286 - 3
Multilayer Transient Voltage Surge Suppressor AUML Varistor Series Surface Mount Varistors 166 www.littelfuse.com Standard Packaging Tape and rell is the standard packaging method of the AUML series. The standard 300 millimeter (13 inch) reel utilized contains 4000 pieces for the 2200 and 1812 chips, 8000 pieces for the 1210 chip and 10,000 pieces for the 1206 size. To order add “T”to the standard part number, e.g. V18AUMLA222OT. Special Packaging Option1: 178 millimeter (7 inch) reels containing 1000 (2220, 1812), 2000 (1210), 2500 (1206), pieces are available. To order add “H”to the standard part number, e.g. V18AUMLA2220H. Option 2: For small sample quantities (less than 100 pieces) the units are shipped bulk pack. To order add “A”to the standard part number, e.g. V18AUMLA2220A.