V15G1C25T

V15G1C25T OMRON | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 16

Technical content

V General Purpose Snap Action Switch

• Industry standard design with switching currents of 10A to 21A  Widely used for applications where long life expectancy and high reliability is required.  Choose from a variety of levers, terminals and operating forces.  Right and Left Barrier options are available for the V-21 and V-16 models  Heat resistant versions of the V-15 and V-10 are available.  RoHS Compliant

Ordering Information

■Model Number Legend V - - - - 1. Ratin gs 21: 21 A at 250 VAC 16: 16 A at 250 VAC 2. Contact Gap None: 1 mm (F gap) G: 0.5 mm (G gap) 15: 15 A at 250 VAC 11: 11 A at 250 VAC 10: 10 A at 250 VAC 4: 100 gf 7. Maximum Operatin g Force 6: 400 gf 5: 200 gf 8. Special Purpose T: Heat resisti ve ( V-15 and V-10, only) 4. Contact Form 1: SPDT COM Terminal, Bottom position: COM Terminal, Side position: 2: SPST-NC 9. Mountin g Hole Size None: 3.1 mm None: Standard K: 2.9 mm 3: SPST-NO 4: SPDT 5: SPST-NC 6: SPST-NO 6. Insulation Barrier None: Without Barrier R: Right-hand barrier L: Left-hand barrier Note: These OF values are for the pin plunger models. 3. Actuator None: Pin pl unger 1: Short hinge le ver 2: Hinge le ver 3: Long hinge le ver 4: Sim ulated roller lever 5: Short hinge roller le ver 6: Hinge roller le ver 5. Terminals A: Solder terminals C2: Q uick-connect terminal (#187) C: Q uick-connect terminal (#250) 3 4 521 7 8 96 (Barriers available for V-21 and V-16, only) Note: Consult Omron regarding nomenclature combinations and part numbers not fo und in this datasheet.

122 Snap Action Switch V

■Available Combinations Note: 1. ❍: Available model. Consult OMRON for specific models with standard approval. ■List of Models Thermoplastic Case

21 A (OF: 400 gf)

Note: 1. Add “G” to the part number in the appropriate location to obtain a 0.5 mm contact gap. Add “-K” to the part number in the appropriate location to obtain 2.9 mm mounting holes. Example: V-21G2-1C6-K 2. Not all combinations are available. Consult Omron regarding nomenclature combinations and part numbers not found in this datasheet. Thermoplastic case Thermosetting case M o d e l V - 2 1V - 1 6V - 1 1V - 1 5 V - 1 0 Rated Current 21 A 16 A 11 A 15 A 10 A COM terminal position Insulation Barrier Heat Resistance OF Terminal Symbol 400 gf 400 gf 200 gf 100 gf 400 gf 200 gf 200 gf 100 gf Bottom No Standard (80°C) Quick-connect Quick-connect Heat resistant (150°C) Solder terminals (A) - - - - - - - - - - - - ❍❍❍❍ Quick-connect Quick-connect Y es Standard (80°C) Solder terminals (A) - - - ❍❍ - - - - - - - - - - - - - - - Quick-connect Quick-connect Side No Standard (80°C) Solder terminals (A) - - - - - - - - - - - - ❍❍❍❍ Quick-connect Quick-connect terminal position Contact form Terminal style Actuator Bottom SPDT Quick-connect (#250) (C) V-21-1C6 V-21-1CR6 V-21-1CL6 SPST -NC V-21-2C6 V-21-2CR6 V-21-2CL6 SPST -NO V-21-3C6 V-21-3CR6 V-21-3CL6 SPDT V-211-1C6 V-211-1CR6 V-211-1CL6 V-212-1C6 V-212-1CR6 V-212-1C6 V-213-1C6 V-213-1CR6 V-213-1CL6 V-214-1C6 V-214-1CR6 V-214-1CL6 V-215-1C6 V-215-1CR6 V-215-1CL6 V-216-1C6 V-216-1CR6 V-216-1CL6 Without barrier Without barrier Right-hand barrier Left-hand barrier Pin plunger Short hinge lever Hinge lever Long hinge lever Simulated roller lever Short hinge roller lever Hinge roller lever

16 A (OF: 200 gf)

11 A (OF: 100 gf)

Note: 1. Add “G” to the part number in the appropriate location to obtain a 0.5 mm contact gap. Add “-K” to the part number in the appropriate location to obtain 2.9 mm mounting holes. Examples: 1) V-16G3-1C25-K 2) V-11G-1A4-K 2. Not all combinations are available. Consult Omron regarding nomenclature combinations and part numbers not found in this datasheet. Common terminal position Contact form Terminal style Actuator Bottom SPDT A V-16-1A5 V-16-1AR5 V-16-1AL5 C2 V-16-1C25 V-16-1C2R5 V-16-1C2L5 SPST -NCA V-16-2A5 V-16-2AR5 V-16-2AL5 C2 V-16-2C25 V-16-2C2R5 V-16-2C2L5 SPST -NOA V-16-3A5 V-16-3AR5 V-16-3AL5 C2 V-16-3C25 V-16-3C2R5 V-16-3C2L5 SPDT A V-161-1A5 V-161-1AR5 V-161-1AL5 C2 V-161-1C25 V-161-1C2R5 V-161-1C2L5 A V-162-1A5 V-162-1AR5 V-162-1AL5 C2 V-162-1C25 V-162-1C2R5 V-162-1C2L5 A V-163-1A5 V-163-1AR5 V-163-1AL5 C2 V-163-1C25 V-163-1C2R5 V-163-1C2L5 A V-164-1A5 V-164-1AR5 V-164-1AL5 C2 V-164-1C25 V-164-1C2R5 V-164-1C2L5 A V-165-1A5 V-165-1AR5 V-165-1AL5 C2 V-165-1C25 V-165-1C2R5 V-165-1C2L5 A V-166-1A5 V-166-1AR5 V-166-1AL5 C2 V-166-1C25 V-166-1C2R5 V-166-1C2L5 Without barrier Without barrier Right-hand barrier Left-hand barrier Pin plunger Short hinge lever Hinge lever Long hinge lever Simulated roller lever Short hinge roller lever Hinge roller lever Common terminal position Contact form Terminal style Actuator Bottom SPDT A V-11-1A4 C2 V-11-1C24 C V-11-1C4 A V-111-1A4 C2 V-111-1C24 C V-111-1C4 A V-112-1A4 C2 V-112-1C24 C V-112-1C4 A V-113-1A4 C2 V-113-1C24 C V-113-1C4 A V-114-1A4 C2 V-114-1C24 C V-114-1C4 A V-115-1A4 C2 V-115-1C24 C V-115-1C4 A V-116-1A4 C2 V-116-1C24 C V-116-1C4 Without barrier Pin plunger Short hinge lever Hinge lever Long hinge lever Simulated roller lever Short hinge roller lever Hinge roller lever

124 Snap Action Switch V

Standard models - 15 A / 10 A Note: 1. For SPST -NC and SPST -NO with levers consult Omron. 2. Not all combinations are available. Consult Omron regarding nomenclature combinations and part numbers not found in this datasheet. Heat Resistant Models (Up to 150°C) - 15 A / 10A Note: 1. Add “G” to the part number in the appropriate location to obtain a 0.5 mm contact gap. Add “-K” to the part number in the appropriate location to obtain 2.9 mm mounting holes. Add “C2” to the part number in the appropriate location to obtain versions with #1 87 quick- connect terminals. Example: 1) V-15G1-1C25-T -K 2. Not all combinations are available. Consult Omron regarding nomenclature combinations and part numbers not found in this datasheet. Common terminal position Contact form Terminal style Actuator 15 A 10 A 200 gf 200 gf 100 gf Bottom SPDT A V-15G-1A5-K V-10G-1A5-K V-10G-1A4-K C2 V-15G-1C25-K V-10G-1C25-K V-10G-1C24-K C V-15G-1C5-K — — SPST -NCA V-15G-2A5-K V-10G-2A5-K V-10G-2A4-K C2 V-15G-2C25-K V-10G-2 C25-K V-10G-2C24-K SPST -NOA V-15G-3A5-K V-10G-3A5-K V-10G-3A4-K C2 V-15G-3C25-K V-10G-3 C25-K V-10G-3C24-K C V-15G-3C5-K — — Side SPDT A V-15G-4A5-K V-10G-4A5-K V-10G-4A4-K SPST -NC V-15G-5A5-K V-10G-5A5-K V-10G-5A4-K SPST -NO V-15G-6A5-K V-10G-6A5-K V-10G-6A4-K Bottom SPDT A V-15G1-1A5-K V-10G1- 1A5-K V-10G1-1A4-K C2 V-15G1-1C25-K V-10G1- 1C25-K V-10G1-1C24-K A V-15G2-1A5-K V-10G2- 1A5-K V-10G2-1A4-K C2 V-15G2-1C25-K V-10G2- 1C25-K V-10G2-1C24-K A V-15G3-1A5-K V-10G3- 1A5-K V-10G3-1A4-K C2 V-15G3-1C25-K V-10G3-1C25-K V-10G3-1C24-K A V-15G4-1A5-K V-10G4- 1A5-K V-10G4-1A4-K C2 V-15G4-1C25-K V-10G4-1C25-K V-10G4-1C24-K A V-15G5-1A5-K V-10G5- 1A5-K V-10G5-1A4-K C2 V-15G5-1C25-K V-10G5-1C 25-K V-10G5-1C24-K A V-15G6-1A5-K V-10G6- 1A5-K V-10G6-1A4-K C2 V-15G6-1C25-K — V-10G6-1C24-K Common terminal position Contact form Terminal style Actuator 15 A 10 A 200 gf 100 gf Bottom SPDT Solder Terminals (A) V-15-1A5-T V-10-1A4-T V-151-1A5-T V-101-1A4-T V-152-1A5-T V-102-1A4-T V-153-1A5-T V-103-1A4-T V-154-1A5-T V-104-1A4-T V-155-1A5-T V-105-1A4-T V-156-1A5-T V-106-1A4-T Pin plunger Short hinge lever Hinge lever Long hinge lever Simulated roller lever Short hinge roller lever Hinge roller lever Pin plunger Short hinge lever Hinge lever Long hinge lever Simulated roller lever Short hinge roller lever Hinge roller lever

■Ratings (reference values) Note: 1. The above current values are the normal current values of models with a contact gap of 1 mm (gap F), which vary with the normal current values of models with a contact gap of 0.5 mm (gap G). 3. Lamp load has an inrush current of 10 times the steady-state current. 4. Motor load has an inrush current of 6 times the steady-state current. 5. The ratings values apply under the following test conditions: Ambient temperature: 20±2°C, Ambient humidity: 65±5%, Operating frequency: 30 operations/min ■Approved Standards UL1054 (File No. E41515) CSA C22.2 No.55 (File No. LR21642) EN 61058-1 (File No. 129608, VDE approval) Testing conditions: 5E4 (50,000 operations), T105 (0°C to 105°C) EN 61058-1 (File No. T9451451, TÜV Rheinland approval) Testing conditions: 5E4 (50,000 operations), T85 (0°C to 85°C) Type Rated voltage Non-inductive load Inductive load Resistive load Lamp load Inductive load Motor load NC NO NC NO NC NO NC NO V-21 250 VAC 21 A 3 A 12 A 4 A

8 VDC

30 VDC

125 VDC

250 VDC

0.6 A 0.3 A 5 A 5 A 0.1 A 0.05 A 12 A 12 A 0.6 A 0.3 A 7 A 5 A 0.1 A 0.05 A V-16 250 VAC 16 A 2 A 10 A 3 A 0.6 A 0.3 A 4 A 4 A 0.1 A 0.05 A 10 A 10 A 0.6 A 0.3 A 6 A 4 A 0.1 A 0.05 A V-15 250 VAC 15 A 2 A 10 A 3 A 0.6 A 0.3 A 4 A 4 A 0.1 A 0.05 A 10 A 10 A 0.6 A 0.3 A 6 A 4 A 0.1 A 0.05 A V-11 250 VAC 11 A 1.5 A 6 A 2 A 0.6 A 0.3 A 3 A 3 A 0.1 A 0.05 A 6 A 6 A 0.6 A 0.3 A 3 A 3 A 0.1 A 0.05 A V-10 250 VAC 10 A 1.5 A 6 A 2 A 0.6 A 0.3 A 3 A 3 A 0.1 A 0.05 A 6 A 6 A 0.6 A 0.3 A 3 A 3 A 0.1 A 0.05 A Rated voltage V-21 V-16 V-15 V-11 V-10

125 VAC 21 A, 1/2 HP 16 A, 1/2 HP 15 A, 1/2 HP 11 A, 1/3 HP 10 A, 1/3 HP250 VAC

125 VDC 0.6 A 250 VDC 0.3 A Rated voltage V-21 V-16 V-11

250 VAC 20 (4) A 16 (4) A 11 (3) A

250 VAC 15 A 10 A

250 VDC 0.3 A

126 Snap Action Switch V

■Characteristics Note: 1. Data shown are of initial value. 2. The dielectric strength shown is measured using a separator between the switch and metal mounting plate. 3. For pin plunger models, the above values apply for use at both the free position and total travel position. For lever models, they apply at the total travel position. 4. For testing conditions, contact your OMRON sales representative. ■Contact Specifications Note: Minimum applicable loads are indicated by N standard reference values. This value represents the failure rate at a 60% (λ60) reliability level (JIS C5003). The equation λ60=0.5 x 10-6 / operations indicates that a failure rate of 1/2,000,000 operations can be expected at a reliability level of 60% Operating speed 0.1 mm to 1 m/s (plunger models) Operating frequency Mechanical: 600 operations/minute, max. Electrical: 30 operations/minute, max. Insulation resistance 100 MΩ min. (at 500 VDC) Contact resistance 15 mΩ max. Dielectric strength (see note 2) 1,000 VAC, 50/60 Hz for 1 min between terminals of the same polarity V-21, V-16 and V-11: 2,000 VAC, 50/60 Hz for 1 min between current-carrying metal parts and ground, and between each terminal and non-current-carrying metal parts V-15 and V-10: 1,500 VAC, 50/60 Hz for 1 min between current-carrying metal parts and ground, and between each terminal and non-current-carrying metal parts Vibration resistance (see note 3) Malfunction: 10 to 55 Hz, 1.5-mm double amplitude Shock resistance (see note 3) Destruction: 1,000 m/s 2 (approx. 100G) max. Malfunction: V-21/V-16/V-15: 300 m/s 2 (approx. 30G) max. V-11/V10: 200 m/s 2 (approx. 20G) max. Life expectancy Mechanical: 50,000,000 operations min. (60 operations/minute) Electrical: V-21/V-16/V-15: 100,000 operat ions min. (30 operations/minute) (V-15 heat resistive: 20,000 operations min. (30 ops/minute)) V-11/V-10: 300,000 operations min. (30 operations/minute) (V-10 heat resistive: 50,000 operations min. (30 ops/minute)) Degree of protection IEC IP40 Degree of protection against electric shock Class I Proof tracking index (PTI) 175 Ambient operating temperature -25°C to 80°C (at 60% RH max.) with no icing -25°C to 150°C for heat resistive models (at 60% RH max.) with no icing. Ambient operating humidity 85% max. (for 5°C to 35°C) Weight Approx. 6.2 g (plunger models) Item V-21 V-16 V-15 V-11 V-10 Contact Specification Rivet Material Silver alloy Silver Gap (standard value) 1 mm (F gap type) or 0.5 mm (G gap type) Inrush current NC 50 A max. 40 A max. 36 A max. 24 A max.NO Minimum applicable load 160 mA at 5 VDC

■Contact Form * The SPST- NC and SPST-NO contact form types listed in the ordering information tables are for Pin Plunger models only. For information concerning lever models consult Omron. ■Barrier direction (V-21 and V-16) ■Mounting Holes All switches may be panel mounted using M3 mounting screws with plane washers or spring washers to securely mount the switch. Tighten the screws to a torque of 0.39 to 0.59 N·m. ■ Mechanical service life ■ Electrical service life (Pin plunger models) (Pin plunger models) V-21/-16/-15/-10 Number of operations (x10 ) 200 100 Ambient temperature: 20±2°C Ambient humidity: 65±5% Without load Operating frequency: 600 operations/min V-11 V-10 (1.96 N {200 gf}) V-15 V-16 V-21 OT rated value Full stroke OT (mm) V-21/-16/-15 Operating frequency: 60 operations/min cosφ = 1, 250 VAC 0.5 0.3 0.1 0 4 8 1 21 62 02 42 8 V-21 V-15 V-16 Switching current (A) Number of operations (x10 ) 0.5 0.3 0.1 0 0.5 1 2 3 4 5 6 7 8 9 10 11 12 V-10 V-11 V-11/-10 Switching current (A) Ambient temperature: 20±2°C Ambient humidity: 65±5% Operating frequency: 60 operations/min cosφ = 1, 250 VAC Number of operations (x10 ) Common terminal position Contact form SPDT SPST-NC* SPST-NO* Bottom type Side type Right-hand Barrier Left-hand Barrier Two, 3.1-dia. mounting holes or M3 screw holes 10.3 ± 0.1 22.2 ± 0.1

128 Snap Action Switch V

■Terminals Note: 1. Unless otherwise specified, all units are in millimeters and a tolerance of ±0.4 mm applies to all dimensions 2. The following table is for the SPDT contact specifications. Two terminals will be available for SPST -NO or SPST -NC contact specifications. For terminal positions, refer to the above Contact Form 3. Right-angle PCB terminal type is available with some models (not shown). Drawings will be provided if requested. D5: Pins at right angles, to the right D6: Pins at right angle, to the left Terminal type Solder Terminal (A) Quick-connect Terminal (#187) (C2) Quick-connect Terminal (#250) (C) COM bottom position COM side position Terminal dimensions t = 0.5 Three, solder terminals (10) 2.9 (6.5) (5.5) t = 0.5 Three, quick-connect terminals (#187) (10) 2.9 (6.5) (5.5) t = 0.8 Three, quick-connect terminals (#250) (12.0) 3.2 (7.7) (4.9) (10) 2.4 (6.5) (5.5) (10) 2.4 (6.5) (5.5) (12.0) 3.6 (7.7) (4.9) 1.6 dia.2.4 dia. 4.75±0.1 6.35 3.2 (see note) Note: Indicates the length to the center of the 1.6-dia. holes 1.6-dia. terminal hole 4.75±0.1 3.2 6.35 1.65-dia. terminal hole 6.35±0.1 3.95 8.1

■Dimensions and Operating Characteristics Thermoplastic Case Models Note: 1. Unless otherwise specified, all units are in millimeters and a tolerance of ±0.4 mm applies to all dimensions 2. The following illustrations and drawings are for quick-connect terminals (#250) (terminals C). V models also incorporate termin als A and C2, which are omitted from the following drawings. Refer to Terminals section for the dimensions of these terminals. 3. The @ in the model number is for the terminal code. 5. The operating characteristics are for operation in the A direction ( ). Pin Plunger Models (Without Barrier) V-21-1 6 V-16-1 5 V-11-1 4 3.1+0.13 –0.03 dia. holes 3.1+0.13 –0.03 Three, quick-connect terminals (#250) 20.2±0.25 2.8 1.6 2.8 10.3±0.1 PT OP 27.8 39.8±0.8 2.8 8.4 15.9 19.1 0.6 4.2 2.8 10.3 (With Right-hand Barrier) V-21-1 R6 V-16-1 R5 3.1+0.13 –0.03 dia. holes 3.1+0.13 Three, quick-connect terminals (#250) 20.2±0.25 2.8 1.6 2.8 10.3±0.1 PT OP 27.8 39.8±0.8 40.2 2.8 15.9 8.4 19.1 21.9 0.6 4.2 2.8 0.6 10.3 A A (With Left-hand Barrier) V-21-1 L6 V-16-1 L5 3.1+0.13 –0.03 dia. holes 3.1+0.13 –0.03 3.4±0.15 dia.t=0.8 Three, quick-connect terminals (#250) 2.8 0.6 4.2 0.6 10.3 2.8 19.1 15.9 8.4 21.9 1.6 20.2±0.25 2.8 2.8 (12.0) 2.8 27.8 39.8±0.8 22.2±0.1 40.2 10.3±0.1 PT OP A Characteristics V-21-1 @6 V-16-1 @5 OF max. 400 gf 200 gf RF min. 80 gf 50 gf PT max. 1.2 mm OT min. 1.0 mm MD max. 0.4 mm OP 14.7 ± 0.4 mm Characteristics V-11-1 @4 V-11-1 @5 OF max. 100 gf 200 gf RF min. 20 gf 50 gf PT max. 1.2 mm OT min. 1.0 mm MD max. 0.4 mm OP 14.7 ± 0.4 mm

130 Snap Action Switch V

Note: 1. Unless otherwise specified, all units are in millimeters and a tolerance of ±0.4 mm applies to all dimensions 2. The following illustrations and drawings are for quick-connect terminals (#250) (termina ls C). V models also incorporate termin als A and C2, which are omitted from the following drawings. Refer to Ter minals section for the dimensions of these terminals. 3. The @ in the model number is for the terminal code. 5. The operating characteristics are for operation in the A direction ( ). Short Hinge Lever Models Hinge Lever Models Long Hinge Lever Models V-211-1 6 V-161-1 5 V-111-1 4 3.1+0.13 –0.03 dia. holes 3.1+0.13 –0.03 3.4±0.15 dia. t = 0.5 (see note) t=0.8 Three, quick-connect terminals (#250) 22.1 8.1 PT OP 2.8 10.3±0.1 2.8 (12.0) 27.8 22.2±0.1 39.8±0.8 1.6 2.8 8.4 15.9 19.1 0.6 2.8 4.3 10.3 Note: Stainless-steel lever A Characteristics V-211-1 @6 V-161-1 @5 V-111-1 @4 OF max. 400 gf 200 gf 100 gf RF min. 50 gf 50 gf 15 gf PT max. 1.6 mm OT min. 0.8 mm MD max. 0.6 mm OP 15.2 ± 0.5 mm 3.1+0.13 –0.03 dia. holes 3.1+0.13 –0.03 3.4±0.15 dia. t = 0.5 (see note) t=0.8 Three, quick-connect terminals (#250) 35.6±0.8 8.1 1.6 PT OP 2.8 10.3±0.1 22.2±0.1 (12.0)2.8 27.8 39.8±0.8 2.8 15.9 8.4 19.1 0.6 2.8 4.3 10.3 V-212-1 6 V-162-1 5 V-112-1 4 Note: Stainless-steel lever A Characteristics V-212-1 @6 V-162-1 @5 V-112-1 @4 OF max. 250 gf 125 gf 60 gf RF min. 25 gf 14 gf 6 gf PT max. 4.0 mm OT min. 1.6 mm MD max. 1.5 mm OP 15.2 ± 1.2 mm 3.1+0.13 –0.03 dia. holes 3.1+0.13 –0.03 3.4±0.15 dia. t = 0.5 (see note) t=0.8 Three, quick-connect terminals (#250) 59.4±0.8 PT OP 2.8 10.3±0.1 22.2±0.1 (12.0)2.8 27.8 39.8±0.8 2.8 8.4 15.9 19.1 0.6 2.8 4.3 10.3 V-213-1 6 V-163-1 5 V-113-1 4 Note: Stainless-steel lever 1.6A Characteristics V-213-1 @6 V-163-1 @5 V-113-1 @4 OF max. 130 gf 70 gf 35 gf RF min. 12 gf 6 gf - - - PT max. 9.0 mm OT min. 2.0 mm 3.2 mm MD max. 2.8 mm OP 15.2 ± 2.6 mm15.2 mm+2.6 −3.2

Note: 1. Unless otherwise specified, all units are in millimeters and a tolerance of ±0.4 mm applies to all dimensions 2. The following illustrations and drawings are for quick-connect terminals (#250) (terminals C). V models also incorporate termin als A and C2, which are omitted from the following drawings. Refer to Terminals section for the dimensions of these terminals. 3. The @ in the model number is for the terminal code. 5. The operating characteristics are for operation in the A direction ( ). Simulated Roller Lever Models Short Hinge Roller Lever Models Hinge Roller Lever Models V-214-1 6 V-164-1 5 V-114-1 4 3.1+0.13 –0.03 dia. holes 3.1+0.13 –0.03 3.4±0.15 dia. t = 0.5 (see note) t=0.8 Three, quick-connect terminals (#250) 3.5R 32.6±0.8 8.1 1.6PT OP 2.8 10.3±0.1 22.2±0.1 (12.0)2.8 27.8 39.8±0.8 0.6 3.48 .2 10.3 Note: Stainless-steel lever 2.8 15.9 19.1 8.4 A Characteristics V-214-1 @6 V-164-1 @5 V-114-1 @4 OF max. 250 gf 125 gf 60 gf RF min. 25 gf 14 gf 6 gf PT max. 4.0 mm OT min. 1.6 mm MD max. 1.5 mm OP 18.7 ± 1.2 mm Note: 1. Stainless-steel le ver 2. Oilless polyacetar resin roller V-215-1 6 V-165-1 5 V-115-1 4 3.1+0.13 –0.03 dia. holes 3.1+0.13 –0.03 3.4±0.15 dia. t = 0.5 (see note 1) 4.8 dia. × 4.8 (see note 2) t=0.8 Three, quick-connect terminals (#250) 20.1 8.1 1.6PT OP 2.8 10.3±0.1 22.2±0.1 2.8 (12.0) 27.8 39.8±0.8 2.8 8.4 15.9 19.1 0.6 5.1 10.3 A Characteristics V-215-1 @6 V-165-1 @5 V-115-1 @4 OF max. 480 gf 240 gf 120 gf RF min. 50 gf 50 gf 15 gf PT max. 1.6 mm OT min. 0.8 mm MD max. 0.6 mm OP 20.7 ± 0.6 mm V-216-1 6 V-166-1 5 V-116-1 4 3.1+0.13 –0.03 dia. holes 3.1+0.13 –0.033.4±0.15 dia. t = 0.5 (see note 1) 4.8 dia. × 4.8 (see note 2) t=0.8 Three, quick-connect terminals (#250) 34.0±0.8 8.1 1.6PT OP 2.8 10.3±0.1 22.2±0.1 (12.0)2.8 27.8 39.8±0.8 2.8 19.1 0.6 5.1 10.3 15.9 8.4 Note: 1. Stainless-steel le ver 2. Oilless polyacetar resin roller A Characteristics V-216-1 @6 V-166-1 @5 V-116-1 @4 OF max. 250 gf 125 gf 60 gf RF min. 25 gf 14 gf 6 gf PT max. 4.0 mm OT min. 1.6 mm MD max. 1.5 mm OP 20.7 ± 1.2 mm

132 Snap Action Switch V

Note: 1. Unless otherwise specified, all units are in millimeters and a tolerance of ±0.4 mm applies to all dimensions 2. The following illustrations are for quick-connect terminals (#250) (terminals C). Refer to Terminals section for the dimensions of other terminals. 3. The @ in the model number is for the terminal code. 5. The operating characteristics are for operation in the A direction ( ). Pin Plunger Models Short Hinge Lever Models Hinge Lever Models Long Hinge Lever Models V-15G-1 5-K V-10G-1 5-K V-10G-1 4-K 2.9+0.13 –0.03 dia. holes 3.1+0.13 –0.03 3.4±0.15 dia. t=0.5 Three, solder terminals 20.2±0.25 2.8 2.8 10.3±0.1 PT OP 22.2±0.1 2.8 27.8 (10) 37.8±0.8 15.9 18.8 4.2 2.8 10.3 A Characteristics V-15G-1@5-K V-10G-1@5-K V-10G-1@4-K OF max. 200 gf 100 gf RF min. 50 gf 20 gf PT max. 1.2 mm OT min. 1.3 mm MD max. 0.3 mm OP 14.7 ± 0.4 mm V-15G1-1 5-K V-10G1-1 5-K V-10G1-1 4-K 2.9+0.13 –0.03 dia. holes 3.1+0.13 –0.03 3.4±0.15 dia. t = 0.5 (see note) t=0.5 Three, solder terminals 22.1 8.1 PT 2.8 22.2±0.1 2.8 27.8 (10) 37.8±0.8 15.9 18.8 4.3 2.8 10.3 OP 10.3±0.1 Note: Stainless-steel lever A Characteristics V-15G1-1@5-K OF max. 200 gf 100 gf RF min. 50 gf 15 gf PT max. 1.5 mm OT min. 1.0 mm MD max. 0.5 mm OP 15.2 ± 0.5 mm V-15G2-1 5-K V-10G2-1 5-K V-10G2-1 4-K 2.9+0.13 –0.03 dia. holes 3.1+0.13 –0.03 3.4±0.15 dia. t = 0.5 (see note) t=0.5 Three, solder terminals 35.6±0.8 8.1 PT OP 2.8 10.3±0.1 22.2±0.1 2.8 27.8 (10) 37.8±0.8 15.9 18.8 4.3 2.8 10.3 Note: Stainless-steel lever A Characteristics V-15G2-1@5-K OF max. 125 gf 60 gf RF min. 14 gf 6 gf PT max. 3.3 mm OT min. 2.3 mm MD max. 0.8 mm OP 15.2 ± 1.2 mm15.2 mm+2.6 −3.2 V-15G3-1 5-K V-10G3-1 5-K V-10G3-1 4-K 2.9+0.13 –0.03 dia. holes 3.1+0.13 –0.03 3.4±0.15 dia. t = 0.5 (see note) t=0.5 Three, solder terminals22.2±0.1 27.8 2.8 (10) 15.9 18.8 10.3±0.1OP PT 8.1 4.3 2.8 10.3 37.8±0.8 59.4±0.8 2.8 Note: Stainless-steel lever A Characteristics V-15G3-1@5-K OF max. 70 gf 35 gf RF min. 6 gf - - - gf PT max. 9.0 mm 7.6 mm OT min. 3.0 mm 3.2 mm MD max. 2.0 mm OP 15.2 ± 2.6 mm

Note: 1. Unless otherwise specified, all units are in millimeters and a tolerance of ±0.4 mm applies to all dimensions 2. The following illustrations are for quick-connect terminals (#250) (terminals C). Refer to Ter minals section for the dimensions of other terminals. 3. The @ in the model number is for the terminal code. 5. The operating characteristics are for operation in the A direction ( ). Simulated Roller Lever Models Short Hinge Roller Lever Models Hinge Roller Lever Models Accessories Refer to the “V/VX/D3C Common Accessories” datasheet for information regarding VAL, VAM and VAV external actuators (sold separately). V-15G4-1 5-K V-10G4-1 5-K V-10G4-1 4-K 3.5R 2.9+0.13 –0.03 dia. holes 3.1+0.13 –0.03 3.4±0.15 dia. t = 0.5 (see note) t=0.5 Three, solder terminals22.2±0.1 27.8 2.8 (10) 15.9 18.8 10.3±0.1OP PT 8.1 4.3 2.8 10.3 37.8±0.8 32.6±0.8 2.8 Note: Stainless-steel lever A Characteristics V-15G4-1@5-K OF max. 125 gf 60 gf RF min. 14 gf 6 gf PT max. 3.3 mm OT min. 2.3 mm MD max. 0.8 mm OP 18.7 ± 1.2 mm 4.8 dia. × 4.8 (see note 2) 2.9+0.13 –0.03 dia. holes 3.1+0.13 –0.033.4±0.15 dia. t = 0.5 (see note 1) 22.2±0.1 27.8 2.8 (10) 15.9 18.8 10.3±0.1 OP PT 8.1 5.1 10.3 37.8±0.8 20.1 2.8 V-15G5-1 5-K V-10G5-1 5-K V-10G5-1 4-K Note: 1. Stainless-steel le ver 2. Oilless polyacetar resin roller A t=0.5 Three, solder terminals Characteristics V-15G5-1@5-K OF max. 240 gf 120 gf RF min. 50 gf 15 gf PT max. 1.5 mm OT min. 1.0 mm MD max. 0.5 mm OP 20.7 ± 0.6 mm V-15G6-1 5-K V-10G6-1 5-K V-10G6-1 4-K 4.8 dia. × 4.8 (see note 2) 2.9+0.13 –0.03 dia. holes 3.1+0.13 –0.03 3.4±0.15 dia. t = 0.5 (see note 1) 22.2±0.1 27.8 2.8 (10) 15.9 18.8 10.3±0.1 OP PT 8.1 5.1 10.3 37.8±0.8 34.0±0.8 2.8 Note: 1. Stainless-steel le ver 2. Oilless polyacetar resin roller A t=0.5 Three, solder terminals Characteristics V-15G6-1@5-K OF max. 125 gf 60 gf RF min. 14 gf 6 gf PT max. 3.3 mm OT min. 2.3 mm MD max. 0.8 mm OP 20.7 ± 1.6 mm

134 Snap Action Switch V

Be sure to read the precautions and information common to all Snap Action and Detection Switches, contained in the Technical User’s Guide, “Snap Action Switches, Technical Information” for correct use. ■Correct Use Terminal Connection To solder the lead to the solder terminal, apply a soldering iron rated at 60 W max. quickly (within 5 seconds) with the actuator at the free position. Note that applying a soldering iron for too long a time or using one that is rated at more than 60 W may degrade the switch characteris- tics. Use an appropriate mating connector for #187 or #250 quick connect terminals. Specifications Approved by TÜV Rheinland According to EN61058-1 Appropriate Cable Size (mm2) Operation Make sure that the operating body pushes the switch actuator with an adequate force when the switch is to be operated, and that it does not touch the actuator when the switch is released. Do not change the operating position by modifying the actuator. Do not use the switch in a application where the operating speed is extremely slow or the actuator is set in the midpoint between the free position and operating position. Install the pin plunger switch so that the operating force is applied in alignment with the stroke of the actuator. The switch should be set so that its stroke is in the range of 60 to 90% of the rated OT (minimum value) when the switch has been operated. ■Cautions Insulation Distance According to E N61058-1, the minimum insulation thickness for this switch should be 1.1 mm and minimum clearance distance between the terminal and mounting plate should be 1.0 mm. If the insulation distance cannot be provided in the product incorporating the switch, either use a switch with insulation barrier or use a separator to ensure sufficient insulation distance. Model Solder terminal V-15 1.25, 2.0

Global - http://www.omron.com USA - http://www.components.omron.com Cat. No. X303-E-1 Printed in USA OMRON ELECTRONIC COMPONENTS LLC 55 E. Commerce Drive, Suite B Schaumburg, IL 60173 847-882-2288 11/10 Specifications subject to change without notice All sales are subject to Omron Electronic Components LLC standard terms and conditions of sale, which ALL DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.