UPC8119T_02 NEC | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 3
Technical content
SYMBOLS PARAMETERS AND CONDITIONS UNITS MIN TYP MAX ICC Circuit Current (no signal) mA 7.5 11 15 GCR Gain Control 2f = 950 MHz, PIN = -30 dBm dB 40 50 f = 1440 MHz, PIN = -30 dBm dB 35 45 f = 1900 MHz, PIN = -30 dBm dB 22 GPMAX Maximum Power Gain, f = 950 MHz, PIN = -30 dBm dB 10 12.5 15 f = 1440 MHz, PIN = -30 dBm dB 10 13 16 f = 1900 MHz, PIN = -30 dBm dB 12.5 P1dB Output Power at 1 dB compression, f = 950 MHz, GPMAX dBm 0 +3 f = 1440 MHz, GPMAX dBm +1 +4 f = 1900 MHz, GPMAX dBm +3 NF Noise Figure f = 950 MHz, G PMAX dB 8.5 11.5 f = 1440 MHz, GPMAX dB 7.5 10.5 f = 1900 MHz, GPMAX dB 7.2 RLIN Input Return Loss f = 950 MHz, GPMAX dB 3 6 f = 1440 MHz,GPMAX dB 3 6 ISOL Isolation f = 950 MHz, G PMAX dB 27 32 f = 1440 MHz, GPMAX dB 31 36
- FREQUENCY RESPONSE: 800 MHz to 1.9 GHz
- SUPPLY VOLTAGE RANGE: 2.7~3.3 V
- V AGC: 0.6~2.3 V
- SUPER SMALL SURFACE MOUNT PACKAGE
- TAPE AND REEL PACKAGING OPTION AVAILABLE
- GAIN CONTROL RANGE UP TO 40 dB
FEATURES
1.9 GHz AGC AMPLIFIER
ELECTRICAL CHARACTERISTICS (TA = 25°C, VCC = 3.0 V, ZS = ZL = 50 Ω)
DESCRIPTION
California Eastern Laboratories UPC8119T UPC8119T GAIN vs. AGC VOLTAGE -10 -20 -30 0 12 3 Gain, dB VAGC Voltage, VAGC (V) The UPC8119T is a Silicon Monolithic Microwave Integrated Circuit which is manufactured using the NESAT III process. The NESAT III process produces transistors with f T approach- ing 20 GHz. This device is suitable as an Automatic Gain Control Amplifier stage in cellular radios, GPS receivers, PCN, and test/measurement equipment. NEC's stringent quality assurance and test procedures assure the highest reliability and performance.
Pin No. Symbol Pin Voltage Description Equivalent Circuit 1I N —
2 GND 0
4 Out
5V CC 2.7~3.3 6V AGC 0~3.3 SYMBOLS PARAMETERS UNITS MIN TYP MAX VCC Supply Voltage V 2.7 3.0 3.3 VAGC Gain Control Voltage V 0.6 - 2.4 TOP Operating Temperature °C -40 25 +85 PIN Input Level dBm - - -18 1 f Operating Frequency MHz 100 - 1900 IAGC AGC Pin Drive Current mA 0.5 - - ABSOLUTE MAXIMUM RATINGS1 (TA = 25°C) SYMBOLS PARAMETERS UNITS RATINGS VCC Supply Voltage V 3.6 VAGC Gain Control Voltage V 3.6 TOP Operating Temperature °C -40 to +85 TSTG Storage Temperature °C -55 to +150 UPC8119T Notes: 1. Operation in excess of any one of these conditions may result in permanent damage. RECOMMENDED OPERATING CONDITIONS PIN FUNCTIONS Ground pin. This pin must be connected to system ground. Form ground pattern as wide as possible to minimize ground impedance. RF output pin. The output is an open collector with high impedance. External matching circuit is required. Supply voltage pin. This pin should be connected with a bypass capacitor (e.g., 1000 pF) to minimize ground impedance. Gain Control pin. The gain slope vs. increasing AGC voltage is summarized below: Device Gain Slope vs. V AGC UPC8119T Down RF input pin. Input RF signal with 50 Ω source impedance through a coupling capacitor. External matching circuit is not required.Same as V CC through external inductor Note: 1. Padj ≤ -60 dBc @ ∆f = ± 50 kHz. Wave form condition: π/4 QPSK modulation signal, data rate = 42 kbps, roll off ratio = 0.5, PN9 pattern.
OUTLINE DIMENSIONS (Units in mm) PACKAGE OUTLINE T06 LEAD CONNECTIONS Note: All dimensions are typical unless otherwise specified. 1. IN 2. GND 3. GND 4. OUT 5. V CC 6. V AGC (Top View) (Bottom View) PART NUMBER QUANTITY UPC8119T-E3 3K/Reel
ORDERING INFORMATION
Package Markings: UPC8119T - C2M VCC RFOUT VAGC 0.1µF 0.1µF VCC RFOUT VAGC 0.1µF 0.1µF TEST CIRCUIT
900 MHz 1900 MHz
+0.2 -0.32.8 1.5 +0.2 -0.1 3 4 1.9±0.2 -0.05 +0.100.3 0.13±0.11.1 +0.2 -0.1 0 to 0.1 0.95 0.95 0.8 2.9±0.2 FOUT L1 L2 C1 900 6.8nH 15nH 1.5pF 1900 100nH 5nH (TRL) 2.2pF Unless Noted All Other Caps = 1000pF EXCLUSIVE NORTH AMERICAN AGENT FOR NEC RF, MICROWAVE & OPTOELECTRONIC SEMICONDUCTORS CALIFORNIA EASTERN LABORATORIES • Headquarters • 4590 Patrick Henry Drive • Santa Clara, CA 95054-1817 • (408) 988-3500 • Telex 34-6393 • FAX (408) 988-0279 Internet: http://WWW.CEL.COM 01/17/2002 DATA SUBJECT TO CHANGE WITHOUT NOTICE Life Support Applications These NEC products are not intended for use in life support devices, appliances, or systems where the malfunction of these products can reasonably be expected to result in personal injury. The customers of CEL using or selling these products for use in such applications do so at their own risk and agree to fully indemnify CEL for all damages resulting from such improper use or sale.