UPC4084 NEC | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 8
Technical content
J-FET INPUT QUAD OPERATIONAL AMPLIFIER DESCRIPTION FEATURES The uPC4084, is a quad operational amplifier © Very low input bias and offset currents incorporating well matched ion implant P-channel © High input impedance...J-FET Input Stage J-FET on the same chip with standard bipolar tran- © High slew rate: 13 V/us (TYP.) sistors. The key features of this op amp is very © Internal frequency compensation low input bias current and high slew rate ten times © Output short circuit protection faster than conventional general purpose op amps. By these features uPC4084, is excellent choice for wide variety of applications including integrator, active filter, pulse amp etc. CONNECTION DIAGRAM EQUIVALENT CIRCUIT (1/4 Circuit) (Top View) pPC4084C
6 Qs } outa fit OUTs
8 a : Qua o=—far ary | % ere | Qre Int Ive * G z Re = Ro = Rio [4 un — t__ Q13 | Qs the aan In Di Kor oo OUT \\ ke othe OER, ayy pe Re Lat Ra zh we Rn be OUT? [8] OUTs
ORDERING INFORMATION
PART NUMBER PACKAGE QUALITY GRADE HPC4084C 14 PIN PLASTIC DIP (300 mil) Please refer to “Quality grade on NEC Semiconductor Devices” (Document number IEI-1209) published by NEC Corporation to know the specification of quality grade on the devices and its recommended applications. eee Document No.iC-1987A (O.D. No.IC-5876C) Date Published March 1993 M Printed in Japan
ABSOLUTE MAXIMUM RATINGS (Ta = 25 °C) PARAMETER SYMBOL HPC4084 UNIT Input Volage ror) Va v-008 Output Voltage Note 3) V--0.3 to 40.3 Operating Temperature Range “200+ 8 Storage Temperature Range B50 18 Note 1. Reverse connection of supply voltage can cause destruction. Note 2. The input voltage should be allowed to input without damage destruction. Even during the transition period of supply voltage, power on/off etc., this specification should be kept. The normal operation will establish when the both inputs are within the Common Mode Input Voltage Range of electrical : characteristics. Note 3. This specification is the voltage which should be allowed to supply to the output terminal from external without damage or destructive. Even during the transition period of supply voltage, power on/off etc., this specification should be kept. The output voltage of normal operation will be the Output Voltage Swing of electrical characteristics. Note 4. Thermal derating factor is -7.6 mW / °C when ambient temperature is higher than 50 °C. Note 5. Pay careful attention to the total power dissipation not to exceed the absolute maximum ratings, Note RECOMMENDED OPERATING CONDITIONS
ELECTRICAL CHARACTERISTICS (Ta = 25 °C, V* = +15 V) [amscrenere [swear] own [wr [woe [wr [| conomon | Piero |e |e [oe | feed ee Fitaecurextoree |» | |» [om fmf id ee re a ee Se +15 feronmnenimner | w foe ft fe | Sere | | fee [onvennreamey fm || | pm | TS Fite ee oearooae] «|| mw | [wie] ervm ese er Finronmvone | we ||| [aw [eamaroaeeaee | Pain vormewnneain [aware] [se [ [are | nese Pinot orconetowe | [|| | mm [teens _—| er Note 6. Input bias currents flow into IC. Because each currents are gate leak current of P-channel J-FET on input stage. And that are temperature sensitive. Short time measuring method is recommendable to maintain the junction temperature close to the ambient temperature.
TYPICAL PERFORMANCE CHARACTERISTICS (Ta = 25 °C, TYP.) POWER DISSIPATION OPEN LOOP FREQUENCY RESPONSE 800 —— or 120 | = g ft fs . 100 V¥=+15V 1 é NX R= 2kQ so N i PEIN TTT 5 409 IN S$ © iN : S Peet EINK é 5 6 N « 5 \\ 3 a0 Bp tT IN | i" 7 20 IN XN] é ett | IN ie) 20 40 60 80 100 % 10 100 1k 10k 100k 1M 10M Ta—- Ambient Temperature - °C f - Frequency - Hz LARGE SIGNAL FREQUENCY RESPONSE OUTPUT VOLTAGE SWING $ Vi= x15 V $ Ri = 10k ‘ Ri=10kQ 4 2 2 30 me ® " ® 4
2 Vi=s10V &
3 3% 7 > > i) a ee RS eo ° Viss5V ° 4 § § > > 0 IN 100 1k 10k 100 k 1M 10M i) +10 +20 f ~ Frequency - Hz V* — Supply Voltage - V OUTPUT VOLTAGE SWING VOLTAGE FOLLOWER PULSE RESPONSE é . f = 100 pl = S$ 0 .* 7 of) INL 8 a 2 5 4 3 g ; 2 1 fu SA pit te] | = £6 ° Ss \\ $s e.t | | 3 a 0 a ee 100 300 1k 3k 10k ie) 1 2 3 4 Ri Load Resistance ~ 0 Timo - us
INPUT BIAS CURRENT INPUT EQUIVALENT NOISE VOLTAGE DENSITY 100 10¢ < Bin is = 1002 Eo Co Bs ep _! 5 83 3 S> 2 10 2m 10° g a Ee = 5a g ee £ 01 12 10 20-0 20 40 60 80 10 700 1k 10k 100 k Ts- Ambient Temperature - °C f ~ Frequency — Hz SUPPLY CURRENT - | a7 [_ : | 215 :” — + Ei - || | 0 25 =10 218 £20 V* Supply Voltage - V
14PIN PLASTIC DIP (300 mil) 14 8 Ww 1 7 A K 5 [| WHI oly iF He D cB M Omt5 NOTES Irem | _ MILLIMETERS 1) Each lead centerline is located within 0.25 t mm (0.01 inch) ofits true positon (T.P.) at maximum material condition |e [| zsemax. | 0.100 max. | 2) tem “K" t f leads when formed 0.100 (7. ~ paral. |e | osose [0.020888 Le [namin [oe mv. | js [sets | otazsoos [x | ostmv. [0.020 mn. [1 [ast max [orzo max |
0.200 MAK,
[x | zeae) [0.00 3 VY a [_» [025% | ooro8a | Lx [| o2 | oor S
RECOMMENDED SOLDERING CONDITIONS The following conditions (see table below) must be met when soldering this product. Please consult with our sales offices in case other soldering process is used, or in case soldering is done under different conditions. TYPES OF THROUGH HOLE DEVICE [uPC4084C] Soldering Solderi iti Recommended Method oldering conditions condition symbol Wave soldering Solder temperature: 260 °C or below, Flow time: 10 seconds or below
[MEMO] No part of this document may be copied or reproduced in any from or by any means without the prior written consent of NEC Corporation.NEC Corporation assumes no responsibility for any errors which may appear in this document. NEC Corporation does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from use of a device described herein or any other liability arising from use of such device. No license, either express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC Corporation or others. The devices listed in this document are not suitable for use in aerospace equipment, submarine cables, nuclear reactor control systems and life support systems. If customers intend to use NEC devices for above applications or they intend to use "Standard" quality grade NEC devices for applications not intended by NEC, please contact our sales people in advance. Application examples recommended by NEC Corporation. Standard: Computer, Office equipment, Communication equipment, Test and Measurement equipment, Machine tools, Industrial robots, Audio and Visual equipment, Other consumer products, etc. Special: Automotive and Transportation equipment, Traffic control systems, Antidisaster systems, Anticrime systems, etc. M4 92.6 eee