UMFT51AA-01 | DigiCamel IC Datasheet

Online Datasheet

Read UMFT51AA-01 online.

UMFT51AA-01 ETC2 | Alldatasheet

Document overview

Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
PDF pages: 17

Technical content

Neither the whole nor any part of the information contained in, or the product described in this manual, may be adapted or reproduced in any material or electronic form without the prior written consent of the copyright holder. This product and its documentation are supplied on an as -is basis and no warranty as to their suitability for any particular purpose is either made or implied. Future Technology Devices International Ltd w ill not accept any claim for damages howsoever arising as a result of use or failure of this product. Your statutory rights are not affected. This product or any variant of it is not intended for use in any medical appliance, device or system in which the failure of the product might reasonably be expected to result in personal injury. This document provides preliminary information that may be subject to change without notice. No freedom to use patents or oth er intellectual property rights is implied by the publication of this document. Future Technology Devices International Ltd, Unit 1, 2 Seaward Place, Centurion Business Park, Glasgow G41 1HH United Kingdom. Scotland Registered Company Number: SC136640 Copyright © 2015 Future Technology Devices International Limited 1 UMFT51AA-01 Datasheet Version 1.0 Document Reference No.: FT_001141 Clearance No.: FTDI# 479 Future Technology Devices International Datasheet UMFT51AA 8051 Compatible Module UMFT51AA is an FT51A DIP module that is compatible with an 8051 microcontroller.

1 Introduction

The UMFT51AA is a development module for FTDI’s FT51AQ, one of the devices from FTDI’s range of microcontrollers with USB interface bridging features integrated. FT51A is a MCU series which includes the following features: USB client and USB h ub interfaces, 8051 core, 8-bit ADC, UART, SPI, I2C, 245 FIFO and PWM. The UMFT51AA is a module which is designed to plug into a standard 0.6” wide 40 pin DIP socket. All components used, including the FT 51AQ are Pb- free (RoHS compliant).

1.1 Features

The UMFT51AA is built with a FT51A Q; many of the features of the FT51A Q can be utilized with this module. For a full list of the FT51A’s series features refer to the FT51A datasheet which can be found by clicking here. In addition to the features listed in the FT 51A datasheet, the UMFT51AA has the following features:  PCB assembly module is designed to fit a standard 15.24mm (0.6”) wide 40 pin DIP socket. Pins are on a 2.54mm (0.1”) pitch. This module is a drop in replacement for an 8051 microcontroller.  An on board USB type A socket and plug allow modules to be connected to a PC via a standard A extension cable or directly . This module is also capable of cascading several modules by utilizing the USB hub feature.  Debugger interface hea der used for debugging and programming the FT51AQ. Designe d for operation with the FTPD-1 programmer / debugger module . See the FTPD-1 datasheet for details about this module.  Onboard jumper for configuring the FT51AA to be in self powered or USB powered modes.

2 Driver Support

Driver support for the FT51 A USB Device Firmware Updater (DFU) is available as part of the FT51A SDK and is available for the following OS:  Windows 10 32,64-bit  Windows 8.1 32,64-bit  Windows 8 32,64-bit  Windows 7 32,64-bit  Linux 3.0 and greater

3 Ordering Information

Module Code Utilised IC Code Description UMFT51AA-01 FT51AQ 8051 compatibility module. Other modules in the FT51A range: Module Code Utilised IC Code Description UMFT51-EVM FT51AQ FT51A demonstration platform.

4 UMFT51AA Signals and Configurations

4.1 UMFT51AA Pin Out

(DIO0) P1.0 (DIO1) P1.1 (DIO2) P1.2 (DIO3) P1.3 (DIO4) P1.4 (DIO5) P1.5 (DIO6) P1.6 (DIO7) P1.7 (DIO8) P3.0 (DIO9) P3.1 (DIO10) P3.2 (DIO11) P3.3 (DIO12) P3.4 (DIO13) P3.5 (DIO14) P3.6 (DIO15) P3.7 RST P0.0 (AIO0) Ground P0.1 (AIO1) P0.2 (AIO2) P0.3 (AIO3) P0.4 (AIO4) P0.5 (AIO5) P0.6 (AIO6) P0.7 (AIO7) P2.7 (AIO15) P2.6 (AIO14) P2.5 (AIO13) P2.4 (AIO12) P2.3 (AIO11) P2.2 (AIO10) P2.1 (AIO9) P2.0 (AIO8) VCC Figure 4.1 – Module Pin Out Figure 4.1 illustrates the signals available on the DIL pins. The top image shows the pinout when the module is viewed from the top. The bottom image shows what signals are available whe n viewed from the bottom.

4.2 Signal Descriptions

Pin No. Name Type Description CN1-1 to CN1-8 Port 1 I/O Signals Port 1 pins, P1.0 to P1.7 (DIO0 to DIO7). All FT51A digital functions can be mixed to these pins; however ADC features are not available for these pins. These pins are 5 volt tolerant. CN1-10 to CN1-17 Port 3 I/O Signals Port 3 pins, P3.0 to P3.7 (DIO8 to DIO15). All FT51A digital functions can be mixed to these pins; however ADC features are not available for these pins. These pins are 5 volt tolerant. CN2-21 to CN2-13 Port 2 I/O Signals Port 2 pins, P2.0 to P2.7 (AIO8 to AIO15). ADC features are available for these pins however these pins are not suitable for high frequency data transfers such as SPI. These pins are not 5 volt tolerant. CN2-2 to CN2-9 Port 0 I/O Signals Port 0 pins, P2.0 to P0.7 (AIO8 to AIO15). ADC features are available for these pins however these pins are not suitable for high frequency data transfers such as SPI. These pins are not 5 volt tolerant. CN1-9 RST Reset Pin Active high reset. CN1-20 GND Ground Ground 0 volts. CN2-1 VCC5V Power 5 volt power input when JP1 is open, 5 volt power output when JP1 is closed and connected to upstream USB port. CN1-18 to CN1-19 NC Not Connected Floating pin. CN2-10 to CN2-12 NC Not Connected Floating pin. Table 4.1 – Module Pin Out Description Pin No. Name Type Description CN4-1 VBUS Power 5 volt power input. To enable bus power mode close JP1 CN4-2 DM Signal USB Data - from upstream device CN4-3 DP Signal USB Data + from upstream device CN4-4 GND Ground 0 volt ground. Table 4.2 – Upstream USB Port Pin Out Description

Copyright © 2015 Future Technology Devices International Limited 7 UMFT51AA-01 Datasheet Version 1.0 Document Reference No.: FT_001141 Clearance No.: FTDI# 479 Pin No. Name Type Description CN5-1 VBUS Power 5 volt power output. CN5-2 DM Signal USB Data - to downstream device CN5-3 DP Signal USB Data + to downstream device CN5-4 GND Ground 0 volt ground. Table 4.3 – Downstream USB Port Pin Out Description Pin No. Name Type Description CN3-1 and CN3-4 NC Not Connected Floating pin. CN3-2 VCC5V Power 5 volt power input. (Protected by zenor diode.) CN3-3 RESET# Signal Active low reset input from the FTPD-1 debugger/programmer CN3-5 DBG Signal Debugger data line, single line half-duplex UART. CN3-6 GND Ground 0 volt ground. Table 4.4 – Debugger Port Pin Out Description

4.3 I/O Pin Feature Options

The following features can be configured using the FT51 A’s multiplexer to bring signal to the available pins. FT51A IO Signal Option Available On Pin Description GPIO DIO0-15 and AIO0-

15 General purpose IO

ADC AIO0-15 8-bit analog to digital converter UART DIO0-15 UART interface. Data rates up to 6 Mbaud. SPI Master DIO0-15 SPI master interface. Clock frequency up to 24MHz SPI Slave DIO0-15 SPI slave interface 245 FIFO DIO0-15 8 bit parallel data interface with handshake. Data rates up to 7MB/s. I2C Master DIO0-15 I2C interface. Data rates up to 3.4Mb/s I2C Slave DIO0-15 I2C interface PWM DIO0-15 and AIO0- 15 Pulse Width Modulation output. BCD Detect DIO0-15 and AIO0- Indicates a dedicated charger port has be detect on the upstream USB port. Table 4.5 – I/O Signal Options

5 Module Configurations

5.1 Jumper Configuration Options

Link No. Setting Status Description JP1 Opened Non- Defaul t Self-Powered mode. This setting removes the connection between VBUS and VCC5V. For self-powered operation 5V power is received from CN2-1. JP1 Closed Defaul t Bus-Powered mode. This setting creates a connection between VBUS and VCC5V. For bus-powered operations 5V power will be output on CN2-1 when the module is connected to an upstream USB port. Table 5.1 – Jumper JP1 Modes Warning: There should never be more than one power output supplying power to the same net at any one time. Closing JP1 will cause a direct short between two different power supplies, when a self-powered set-up is applied and the USB bus is connected resulting in the potential for damage to the module and other connected circuitry.

5.2 Programming Firmware to the Flash ROM

The FT51A can be programmed using the FTPD -1. CN3 is a dedicated port that can interface with the FTPD-1. A list of availab le examples (at time of writing) is shown below and source code can be found in ‘C:\\Users\\Username\\Documents\\FTDI\\FT51A_SDK\\version\\examples’ after installing the FT51A SDK:  AN_344_FT51A_DFU_Sample  AN_345 FT51A Keyboard Sample  AN_346 FT51A Mouse Sample  AN_347 FT51A Test and Measurement Sample  AN_348 FT51A FT800 Sensors Sample  AN_349 FT51A FT800 Spaced Invaders Sample  AN_351 FT51A Compatibility Module  AN_354 FT51A Standalone Demo Application Users can develop their own custom applications using the SDK.

6 Module Dimensions

57.53 9.28 68.38 83.13 7.88 2.54 18.45 15.24 Figure 6.1 – UMFT51AA Module Dimensions All dimensions are given in millimetres. The UMFT51AA module exclusively uses lead free components, and is fully compliant with European Union directive 2002/95/EC.

7 UMFT51AA Module Circuit Schematic

8 Contact Information

Head Office – Glasgow, UK Unit 1, 2 Seaward Place, Centurion Business Park Glasgow G41 1HH United Kingdom Tel: +44 (0) 141 429 2777 Fax: +44 (0) 141 429 2758 E-mail (Sales) sales1@ftdichip.com E-mail (Support) support1@ftdichip.com E-mail (General Enquiries) admin1@ftdichip.com Branch Office – Taipei, Taiwan 2F, No. 516, Sec. 1, NeiHu Road Taipei 114 Taiwan , R.O.C. Tel: +886 (0) 2 8797 1330 Fax: +886 (0) 2 8751 9737 E-mail (Sales) tw.sales1@ftdichip.com E-mail (Support) tw.support1@ftdichip.com E-mail (General Enquiries) tw.admin1@ftdichip.com Branch Office – Tigard, Oregon, USA

7130 SW Fir Loop

Tigard, OR 97223 USA Tel: +1 (503) 547 0988 Fax: +1 (503) 547 0987 E-Mail (Sales) us.sales@ftdichip.com E-Mail (Support) us.support@ftdichip.com E-Mail (General Enquiries) us.admin@ftdichip.com Branch Office – Shanghai, China Room 1103, No. 666 West Huaihai Road, Shanghai, 200052 China Tel: +86 (0)21 6235 1596 Fax: +86 (0)21 6235 1595 E-mail (Sales) cn.sales@ftdichip.com E-mail (Support) cn.support@ftdichip.com E-mail (General Enquiries) cn.admin@ftdichip.com Web Site http://ftdichip.com Distributor and Sales Representatives Please visit the Sales Network page of the FTDI Web site for the contact details of our distributor(s) and sales representative(s) in your country. System and equipment man ufacturers and designers are responsible to ensure that their systems, and any Future Technology Devices International Ltd (FTDI) devices incorporated in their systems, meet all applicable safety, regulatory and system -level performance requirements. All application-related information in this document (including application descriptions, suggested FTDI devices and other materials) is provided for reference only. While FTDI has taken care to assure it is accurate, this information is subject to customer confirmation, and FTDI disclaims all liability for system designs and for any applications assistance provided by FTDI. Use of F TDI devices in life support and/or safety applications is entirely at the user’s risk, and the user agrees to defend, indemnify a nd hold harmless FTDI from any and all damages, claims, suits or expense resulting from such use. This document is subject to change without notice. No freedom to use patents or other intellectual property rights is implied by the publication of this documen t. Neither the whole nor any part of the information contained in, or the product described in this document, may be adapted or reproduced in any material or electronic form without the prior written consent of the copyright holder. Future Technology Devic es International Ltd, Unit 1, 2 Seaward Place, Centurion Business Park, Glasgow G41 1HH, United Kingdom. Scotland Registered Company Number: SC136640

Copyright © 2015 Future Technology Devices International Limited 14 UMFT51AA-01 Datasheet Version 1.0 Document Reference No.: FT_001141 Clearance No.: FTDI# 479 Appendix A – References Document References FT51A Datasheet AN_289 FT51A programmers Guide FTPD-1 Datasheet AN_344_FT51A_DFU_Sample AN_345_FT51A_Keyboard_Sample AN_346_FT51A_Mouse_Sample AN_347_FT51A_Test_and_Measurement_Sample AN_348_FT51A_FT800_Sensors_Sample AN_349_FT51A_FT800_Spaced_Invaders_Sample AN_352_FT51A_Installation_Guide Acronyms and Abbreviations Terms Description ADC Analog to digital conversion I2C Inter integrated Circuit LCD Liquid Crystal Display LED Light Emitting Diode MCU Micro Controller Unit SPI Serial Peripheral Interface USB Universal Serial Bus

Copyright © 2015 Future Technology Devices International Limited 16 UMFT51AA-01 Datasheet Version 1.0 Document Reference No.: FT_001141 Clearance No.: FTDI# 479 Appendix C – Revision History Document Title: UMFT51AA-01 Datasheet Document Reference No.: FT_001141 Clearance No.: FTDI# 479 Product Page: http://www.ftdichip.com Document Feedback: Send Feedback Revision Changes Date Version 1.0 Initial Release 2015-11-18

Revision History

Revision history (internal use only, please clearly state all changes here before saving the file) Revision Date YYYY-MM-DD Changes Editor Draft 2014-07-11 Initial Datasheet Created John Quinn Draft 2014-11-28 Reviewed, edited, and commented. Not recommended for release at this stage G Lunn 1.0 2015-11-09 Reviewed and major edits Closed what comments I could G Lunn 1.0 2015-11-10 Reviewed. Some changes made. D Paterson 1.0 2015-11-13 Reviewed and recommend for approval G Lunn 1.0 2015-11-18 Minor formatting; Approved LCE L Subramanian

Product Information

UMFT51AA-01 specifications and overview.

Summary

UMFT51AA 8051 Compatible Module

Description

UMFT51AA 8051 Compatible Module

Source title UMFT51AA-01 Datasheet(PDF) - List of Unclassifed Manufacturers

Related Parts

More parts from the same family.

Browse manufacturer