5713 ALLEGRO | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 4

Technical content

DUAL PERIPHERAL AND POWER DRIVER DISCONTINUED PRODUCT — FOR REFERENCE ONLY This “mini-DlP” dual peripheral and power driver is a bipolar monolithic integrated circuit incorporating NOR logic gates, high- current switching transistors, and transient suppression diodes on the same chip. The two output transistors are capable of simultaneously sinking 300 mA continuously at ambient temperatures of up to +70°C. In the OFF state, this driver will withstand at least 80 V. The UDN5713M dual driver is ideally suited for interface between low-level or high-level logic and high-current/high-voltage loads. Typical applications include driving peripheral loads such as incandes- cent lamps, light-emitting diodes, memories, and heaters with a load current of up to 600 mA. The integral transient suppression diodes allow the use of these drivers with inductive loads such as relays, solenoids, or stepping motors without the need for discrete diodes. Similar devices with four drivers per package are the 5703 and 5706.

FEATURES

n DTL/TTL/PMOS/CMOS Compatible Inputs n Low Input Current n 300 mA Continuous Output Current n Stand-off Voltage of 80 V Dwg. No. A-9789 DUAL PERIPHERAL AND POWER DRIVER — TRANSIENT PROTECTED OUTPUTS 5713 Always order by complete part number, e.g.,UDN5713M . ABSOLUTE MAXIMUM RATINGS Output Off-State Voltage, Output On-State Sink Current, Suppression Diode Off-State Voltage, Suppression Diode On-State Current, Power Dissipation at TA = 25°C, PD Operating Free-Air Temperature Range, Storage Temperature Range, *Derate at the rate of 12.5 mW/°C above TA = 25°C. Data Sheet 29307B

DUAL PERIPHERAL AND POWER DRIVER

115 Northeast Cutoff, Box 15036

Worcester, Massachusetts 01615-0036 (508) 853-5000 Min. Nom. Max. Units Supply Voltage (VCC ) 4.75 5.0 5.25 V Operating Temperature Range 0 +25 +85 °C Current into any output (ON state) — — 300 mA RECOMMENDED OPERATING CONDITIONS ELECTRICAL CHARACTERISTICS over operating temperature range (unless otherwise noted). Test Conditions Limits Driven Other Characteristic Symbol Temp. V CC Input Input Output Min. Typ. Max. Units Notes “1” Input Voltage V IN(1) — MIN — — — 2.0 — — V — “0” Input Voltage V IN(0) — MIN — — — — — 0.8 V — “0” Input Current at all Inputs except Strobe I IN(0) — MAX 0.4 V 30 V — — -50 -100 µA 2 “0” Input Current at Strobe IIN(0) — MAX 0.4 V 30 V — — -100 -200 µA— “1” Input Current at all Inputs except Strobe I IN(1) — MAX 30 V 0 V — — — 10 µA 2 “1” Input Current at Strobe IIN(1) — MAX 30 V 0 V — — — 20 µA— Input Clamp Voltage V IK — MIN -12 mA — — — — -1.5 V — Limits Characteristic Symbol Test Conditions Min. Typ. Max. Units Notes Turn-on Delay Time t pd0 VS = 70 V, RL = 465 Ω (10 Watts), — 200 500 ns 3 C L = 15 pF Turn-off Delay Time t pd1 VS = 70 V, RL = 465 Ω (10 Watts), — 300 750 ns 3 C L = 15 pF SWITCHING CHARACTERISTICS at VCC = 5.0 V, TA = 25°C NOTES: 1. Typical values are at VCC = 5.0 V, TA = 25°C. 2. Each input tested separately. 3. Voltage values shown in the test circuit waveforms are with respect to network ground terminal. 4. Capacitance values specified include probe and test fixture capacitance. INPUT PULSE CHARACTERISTICS VIN(0) = 0 V t f = 7 ns t p = 1 µs VIN(1) = 3.5 V t r = 14 ns PRR = 500 kHz W Copyright © 1976, 1997, Allegro MicroSystems, Inc.

DUAL PERIPHERAL AND POWER DRIVER ELECTRICAL CHARACTERISTICS over operating temperature range (unless otherwise noted). Test Conditions Limits Driven Other Characteristic Symbol Temp. V CC Input Input Output Min. Typ. Max. Units Notes “1” Output Reverse Current lOFF — MIN 2.0 V 0 V 80 V — — 100 µA— — OPEN 2.0 V 0 V 80 V — — 100 µA— “0” Output Voltage V ON — MIN 0.8 V 0.8 V 150 mA — 0.35 0.5 V — — MIN 0.8 V 0.8 V 300 mA — 0.5 0.7 V — Diode Leakage Current I LK NOM NOM 0 V 0 V OPEN — — 200 µA3 Diode Forward Voltage Drop VD NOM NOM V CC VCC — — 1.5 1.75 V 4 “1” Level Supply Current l CC(1) NOM MAX 5.0 V 5.0 V — — 8.0 13 mA 1, 2 “0” Level Supply Current l CC(0) NOM MAX 0 V 0 V — — 36 50 mA 1, 2 NOTES: 1. Typical values are at VCC = 5.0 V, TA = 25°C. 2. Per package. 3. Diode leakage current measured at V R = 80 V. 4. Diode forward voltage drop measured at IF = 300 mA. 5. Capacitance values specified include probe and test fixture capacitance. Dwg. No. A-9123A Dwg. No. A-7628C

DUAL PERIPHERAL AND POWER DRIVER Worcester, Massachusetts 01615-0036 (508) 853-5000 Dimensions in Millimeters (Based on 1” = 25.4 mm) Dimensions in Inches 0.014 0.008 0.300 BSC Dwg. MA-001-8A in 0.430 MAX 0.100 BSC 0.022 0.014 0.400 0.355 0.005 MIN 0.150 0.115 0.280 0.240 0.210 MAX 0.070 0.0450.015 MIN 0.355 0.204 7.62 BSC Dwg. MA-001-8A mm 10.92 MAX 10.16 9.02 2.54 BSC 0.13 MIN 3.81 2.93 7.11 6.10 5.33 MAX 1.77 1.150.39 MIN 0.558 0.356 NOTES: 1. Lead thickness is measured at seating plane or below. 2. Lead spacing tolerance is non-cumulative. 3. Exact body and lead configuration at vendor’s option within limits shown. Allegro MicroSystems, Inc. reserves the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the design of its products. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, Inc. assumes no responsibility for its use; nor for any infringements of patents or other rights of third parties which may result from its use.