UDN2916LB-T

A2916 ALLEGRO | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 8

Technical content

The UDN2916B, UDN2916EB, and UDN2916LB motor drivers are designed to drive both windings of a bipolar stepper motor or bidirectionally control two dc motors. Both bridges are capable of sustaining 45 V and include internal pulse-width modulation (PWM) control of the output current to 750 mA. The outputs have been opti- mized for a low output saturation voltage drop (less than 1.8 V total source plus sink at 500 mA). For PWM current control, the maximum output current is deter- mined by the user’s selection of a reference voltage and sensing resistor. Two logic-level inputs select output current limits of 0, 33, 67, or 100% of the maximum level. A PHASE input to each bridge determines load current direction. The bridges include both ground clamp and flyback diodes for protection against inductive transients. Internally generated delays prevent cross-over currents when switching current direction. Special power-up sequencing is not required. Thermal protection circuitry disables the outputs if the chip temperature exceeds safe operating limits. The UDN2916B is supplied in a 24-pin dual in-line plastic batwing package with a copper lead-frame and heat sinkable tabs for improved power dissipation capabilities. The UDN2916EB is supplied in a 44-lead power PLCC for surface mount applications. The UDN2916LB is supplied in a 24-lead surface-mountable SOIC. Their batwing construc- tion provides for maximum package power dissipation in the smallest possible construction. The UDN2916B/EB/LB are available for opera- tion from -40°C to +85°C. To order, change the prefix from 'UDN' to 'UDQ'. These devices are also available on special order for operation to +105°C. The B and LB packages are available in a lead (Pb) free version, with 100% matte tin leadframe.

FEATURES

■ 750 mA Continuous Output Current ■ 45 V Output Sustaining Voltage ■ Internal Clamp Diodes ■ Internal PWM Current Control ■ Low Output Saturation Voltage ■ Internal Thermal Shutdown Circuitry ■ Similar to Dual PBL3717, UC3770 Always order by complete part number: Part Number Package UDN2916B 24-Pin DIP UDN2916B-T 24-Pin DIP, Lead-free UDN2916EB 44-Lead PLCC UDN2916LB 24-Lead SOIC UDN2916LB-T 24-Lead SOIC, Lead-free UDN2916B (DIP) 1312 θ 2 θ 1 V CC V BB GROUND GROUND GROUND GROUND 02 I 12 I PHASE 2 V REF 2 2RC 1RC V REF 1 PHASE 1 11 I 2BOUT SEN SE 2 2AOUT 1AOUT SEN SE 1 1BOUT 01 I LOAD SUPPLY LOGIC SUPPLY Dw g . PP- 005 PWM 1 PWM 2 Data Sheet29319.20G ABSOLUTE MAXIMUM RATINGS Output Current, IOUT Logic Input Voltage Range, Package Power Dissipation, Operating Temperature Range, Storage Temperature Range, Output current rating may be limited by duty cycle, ambient temperature, and heat sinking. Under any set of conditions, do not exceed the specified peak current rating or a junction temperature of +150°C. 2916

115 Northeast Cutoff, Box 15036

Worcester, Massachusetts 01615-0036 (508) 853-5000 2916 DUAL FULL-BRIDGE MOTOR DRIVER V REF 2 GND GND GND GND 17 29 Dwg. PP-006A PWM 1 PWM 2 LOGIC SUPPLY OUT 1A E 1 SENSE 1 I01 VREF 1 PHASE 1 RC 1 I11 OUT 1B LOAD SUPPLY OUT 2A I02 SENSE 2 PHASE 2 RC 2 I12 OUT 2B VCC VBB NO CONNECTION NO CONNECTION NC NC V REF Dwg. EP-007B VBB SENSE ONE SHOT SOURCE DISABLE RC ÷10 E OUT A OUT B 'B' PACKAGE, CHANNEL 1 PIN NUMBERS SHOWN. R C R S R T C C C T 20 kΩ 40 kΩ 10 kΩ 211 UDN2916EB (PLCC) VBB GROUND GROUND 2BOUT SENSE 2 2AOUT 1AOUT SENSE 1 1BOUT 01 I LOAD SUPPLY Dwg. PP-047 GROUND GROUND 02 I 12 I PHASE 2 V REF 2 2RC V CC 1RC V REF 1 PHASE 1 11 I LOGIC SUPPLY PWM 2PWM 1 θ 1 θ 2 UDN2916LB (SOIC) PWM CURRENT-CONTROL CIRCUITRY 50 75 100 125 150 ALLOWABLE PACKAGE POWER DISSIPATION IN WATTSTEMPERATURE IN °°°°C Dwg. GP-035B R = 6.0°C/W SUFFIX 'B', R = 40°C/W SUFFIX 'LB', R = 77°C/W SUFFIX 'EB', R = 30°C/W θJT θJA θJA θJA TRUTH TABLE PHASE OUT A OUT B HHL LLH Copyright © 1994, 2003 Allegro MicroSystems, Inc.

www.allegromicro.com 3 Limits Characteristic Symbol Test Conditions Min. Typ. Max. Units Output Drivers (OUTA or OUTB) Motor Supply Range V BB 10 — 45 V Output Leakage Current I CEX VOUT = VBB — < 1.0 50 µA VOUT = 0 — <–1.0 –50 µA Output Sustaining Voltage V CE(sus) IOUT = ±750 mA, L = 3.0 mH 45 — — V Output Saturation Voltage V CE(SAT) Sink Driver, IOUT = +500 mA — 0.4 0.6 V Sink Driver, IOUT = +750 mA — 1.0 1.2 V Source Driver, IOUT = –500 mA — 1.0 1.2 V Source Driver, IOUT = –750 mA — 1.3 1.5 V Clamp Diode Leakage Current I R VR = 45 V — < 1.0 50 µA Clamp Diode Forward Voltage V F IF = 750 mA — 1.6 2.0 V Driver Supply Current I BB(ON) Both Bridges ON, No Load — 20 25 mA IBB(OFF) Both Bridges OFF — 5.0 10 mA Control Logic Input Voltage V IN(1) All inputs 2.4 — — V VIN(0) All inputs — — 0.8 V Input Current I IN(1) VIN = 2.4 V — <1.0 20 µA VIN = 0.8 V — – 3.0 –200 µA Reference Voltage Range V REF Operating 1.5 — 7.5 V Current Limit Threshold V REF/VSENSE I0 = I1 = 0.8 V 9.5 10 10.5 — I0 = 2.4 V, I1 = 0.8 V 13.5 15 16.5 — I0 = 0.8 V, I1 = 2.4 V 25.5 30 34.5 — Thermal Shutdown Temperature T J — 170 — °C Total Logic Supply Current I CC(ON) I0 = I1 = 0.8 V, No Load — 40 50 mA ICC(OFF) I0 = I1 = 2.4 V, No Load — 10 12 mA Fixed Off-Time t off RT = 56 kΩ , CT = 820 pF — 46 — µs ELECTRICAL CHARACTERISTICS at TA = +25°C, TJ ≤≤≤≤≤ 150°C, VBB = 45 V, VCC = 4.75 V to 5.25 V, VREF = 5.0 V (unless otherwise noted). (at trip point)

Worcester, Massachusetts 01615-0036 (508) 853-5000 2916 DUAL FULL-BRIDGE MOTOR DRIVER APPLICATIONS INFORMATION PWM CURRENT CONTROL The UDN2916B/EB/LB dual bridges are designed to drive both windings of a bipolar stepper motor. Output current is sensed and controlled independently in each bridge by an external sense resistor (RS), internal com- parator, and monostable multivibrator. When the bridge is turned ON, current increases in the motor winding and it is sensed by the external sense resistor until the sense voltage (VSENSE) reaches the level set at the comparator’s input: ITRIP = VREF/10 RS The comparator then triggers the monostable which turns OFF the source driver of the bridge. The actual load current peak will be slightly higher than the trip point (especially for low-inductance loads) because of the internal logic and switching delays. This delay (t d) is typically 2 µs. After turn-off, the motor current decays, circulating through the ground-clamp diode and sink transistor. The source driver’s OFF time (and therefore the magnitude of the current decrease) is determined by the monostable’s external RC timing components, where t off = RTCT within the range of 20 kΩ to 100 kΩ and 100 pF to 1000 pF. The fixed-off time should be short enough to keep the current chopping above the audible range (< 46 µs) and long enough to properly regulate the current. Be- cause only slow-decay current control is available, short off times (< 10 µs) require additional efforts to ensure proper current regulation. Factors that can negatively affect the ability to properly regulate the current when using short off times include: higher motor-supply volt- age, light load, and longer than necessary blank time. When the source driver is re-enabled, the winding current (the sense voltage) is again allowed to rise to the comparator’s threshold. This cycle repeats itself, main- taining the average motor winding current at the desired level. Loads with high distributed capaci-tances may result in high turn-ON current peaks. This peak (appear- ing across R S) will attempt to trip the comparator, result- ing in erroneous current control or high-frequency oscillations. An external R CCC time delay should be used to further delay the action of the comparator. Depending on load type, many applications will not require these external components (SENSE connected to E). PWM OUTPUT CURRENT WAVE FORM LOAD CURRENT PATHS Dwg. WM-003-1A V PHASE I OUT td toff I TRIP Dwg. E P-006-1 R S BBV BRIDGE ON SOURCE OFF ALL OFF

www.allegromicro.com 5 LOGIC CONTROL OF OUTPUT CURRENT Two logic level inputs (l0 and I1) allow digital selection of the motor winding current at 100%, 67%, 33%, or 0% of the maximum level per the table. The 0% output current condition turns OFF all drivers in the bridge and can be used as an OUTPUT ENABLE function. CURRENT-CONTROL TRUTH TABLE l0 I1 Output Current LL V REF/10 RS = ITRIP HL V REF/15 RS = 2/3 ITRIP LH V REF/30 RS = 1/3 ITRIP HH 0 These logic level inputs greatly enhance the implementation of µP-controlled drive formats. During half-step operations, the l 0 and l1 allow the µP to control the motor at a constant torque between all positions in an eight-step TYPICAL APPLICATION sequence. This is accomplished by digitally selecting 100% drive current when only one phase is ON and 67% drive current when two phases are ON. Logic highs on both l 0 and l1 turn OFF all drivers to allow rapid current decay when switching phases. This helps to ensure proper motor operation at high step rates. The logic control inputs can also be used to select a reduced current level (and reduced power dissipation) for ‘hold’ condi- tions and/or increased current (and available torque) for start-up conditions. GENERAL The PHASE input to each bridge determines the direction motor winding current flows. An internally generated deadtime (approximately 2 µs) prevents crossover currents that can occur when switching the PHASE input. All four drivers in the bridge output can be turned OFF between steps (l 0 = l1 ž 2.4 V) resulting in a fast current decay through the internal output clamp and flyback diodes. The fast current decay is desirable in half-step and high-speed applications. The PHASE, l 0,and I1 inputs float high. Varying the reference voltage (VREF) provides continuous control of the peak load current for micro-stepping applications. Thermal protection circuitry turns OFF all drivers when the junction temperature reaches +170°C. It is only intended to protect the device from failures due to excessive junction temperature and should not imply that output short circuits are permitted. The output drivers are re-enabled when the junction temperature cools to +145°C. The UDN2916B/EB/LB output drivers are optimized for low output saturation voltages—less than 1.8 V total (source plus sink) at 500 mA. Under normal operating conditions, when combined with the excellent thermal properties of the batwing package design, this allows continuous operation of both bridges simultaneously at 500 mA. FROM µP VREF Dwg. EP-008B1 VBB FROM µP 1312 θ 2 VCC VBB VREF +5 V STEPPER MOTOR RS RS RC RC RTCT CC CC PWM 1 PWM 2 θ 1 820 pF 56 k Ω CT 820 pF56 kΩ RT

Worcester, Massachusetts 01615-0036 (508) 853-5000 2916 DUAL FULL-BRIDGE MOTOR DRIVER UDN2916B Dimensions in Inches (controlling dimensions) Dimensions in Millimeters (for reference only) NOTES:1. Webbed lead frame. Leads 6, 7, 18, and 19 are internally one piece. 2. Lead thickness is measured at seating plane or below. 3. Lead spacing tolerance is non-cumulative. 4. Exact body and lead configuration at vendor’s option within limits shown. 0.014 0.008 0.300 BSC Dwg. MA-001-25A in 0.430 MAX 16 12 0.280 0.240 0.210 MAX 0.070 0.045 0.015 MIN 0.022 0.014 0.100 BSC 0.005 MIN 0.150 0.115 1.280 1.230 NOTE 1 0.355 0.204 7.62 BSC Dwg. MA-001-25A mm 10.92 MAX 1 12 7.11 6.10 5.33 MAX 1.77 1.15 0.39 MIN 0.558 0.356 2.54 BSC 0.13 MIN 3.81 2.93 32.51 31.24 NOTE 1

www.allegromicro.com 7 UDN2916EB Dwg. MA-005-44A mm 17.65 17.40 0.51 MIN 4.57 4.20 17.65 17.40 16.662 16.510 1.27 BSC 0.812 0.661 144 0.533 0.331 INDEX AREA 16.662 16.510 8.10 7.39 8.10 7.39 1828 Dwg. MA-005-44A in 0.020 MIN 0.050 BSC 144 0.021 0.013 INDEX AREA 2 6 1729 0.695 0.685 0.032 0.026 0.319 0.291 0.319 0.291 0.180 0.165 0.695 0.685 0.656 0.650 0.656 0.650 Dimensions in Millimeters (for reference only) Dimensions in Inches (controlling dimensions) OTES: 1. MO-047AC except for terminal shoulder height. Intended to meet new JEDEC Standard when that is approved. 2. Webbed lead frame. Leads 7-17 and 29-39 are internally one piece. 3. Lead spacing tolerance is non-cumulative. 4. Exact body and lead configuration at vendor’s option within limits shown.

Worcester, Massachusetts 01615-0036 (508) 853-5000 2916 DUAL FULL-BRIDGE MOTOR DRIVER UDN2916LB 0° TO 8° 2 3 7.60 7.40 15.60 15.20 10.65 10.00 0.51 0.33 2.65 2.35 0.10 MIN. 0.32 0.23 1.27 BSC NOTE 1 NOTE 3 1.27 0.40 Dwg. MA-008-25A mm 0° TO 8° 24 13 2 3 0.2992 0.2914 0.6141 0.5985 0.419 0.394 0.020 0.013 0.0926 0.1043 0.0040 MIN. 0.0125 0.0091 Dwg. MA-008-25A in 0.050 BSC NOTE 1 NOTE 3 0.050 0.016 Allegro MicroSystems, Inc. reserves the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the design of its products. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, Inc. assumes no responsibil- ity for its use; nor for any infringements of patents or other rights of third parties which may result from its use. Dimensions in Millimeters (controlling dimensions) Dimensions in Inches (for reference only) NOTES:1. Webbed lead frame. Leads indicated are internally one piece. 2. Lead spacing tolerance is non-cumulative. 3. Exact body and lead configuration at vendor’s option within limits shown.