UD24121 UTC | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 5
Technical content
UNISONIC TECHNOLOGIES CO., LTD UD24121 LINEAR INTEGRATED CIRCUIT www.unisonic.com.tw 1 of 5 Copyright © 2022 Unisonic Technologies Co., Ltd QW-R115-011.E 1.2A, 24V, 1.4MHz STEP-DOWN CONVERTER DESCRIPTION The UTC UD24121 is a monolithic step-down switching mode converter with a built-in power MOSFET. It regulates input volt ages from 4.5V to 24V down to an output voltage as low as 0.81V, and supplies up to 1.2A of load current. Current mode operation provides fast transient response and eases loop stabilization. Fault condition protection includes cycle-by-cycle current limiting and thermal shutdown. The UTC UD24121 requires a minimum number of readily available standard external components. APPLICATIONS * Distributed Power Systems * Battery Charger * Pre-Regulator for Linear Regulators * WLED Drivers FEATURES * 1.2A Peak Output Current * 0.35Ω Internal Power MOSFET Switch * Stable with Low ESR Output Ceramic Capacitors * Up to 92% Efficiency * 0.1μA Shutdown Mode * Fixed 1.4MHz Frequency * Thermal Shutdown * Cycle-by-Cycle Over Current Protection * Wide 4.5V to 24V Operating Input Range * Output Adjustable from 0.81V to 15V ORDERING INFORMATION Ordering Number Package Packing Lead Free Halogen Free UD24121L-AG6-R UD24121G-AG6-R SOT-26 Tape Reel
UD24121 LINEAR INTEGRATED CIRCUIT UNISONIC TECHNOLOGIES CO., LTD 2 of 5 www.unisonic.com.tw Q W - R 1 15-011.E MARKING PIN CONFIGURATION BST GND FB SW IN EN PIN DESCRIPTION PIN NO. PIN NAME DESCRIPTION
1 BST
High-Side Gate Drive Boost Input. BS supplies the drive for the high-side N-Channel MOSFET switch. Connect a 0.01μF or greater capacitor from SW to BST to power the high side switch. 2 GND Ground. 3 FB Feedback. An external resistor divider from the output to GND, tapped to the FB pin sets the output voltage. To prevent current limit run away during a short circuit fault condition, the frequency foldback comparator lowers the oscillator frequency when the FB voltage is below 250mV. 4 EN On/Off Control Input. Pull EN above 1.2V to turn the device on. For automatic enable, connect a 100kΩ resistor between this pin and Vin pin. 5 V IN Supply Voltage. The UD24121 operates from a +4.5V to +24V unregulated input. C1 is needed to prevent large voltage spikes from appearing at the input. 6 SW Power Switching Output. SW is the switching node that supplies power to the output. Connect the output LC filter from SW to the output load. Note that a capacitor is required from SW to BS to power the high-side switch.
UD24121 LINEAR INTEGRATED CIRCUIT UNISONIC TECHNOLOGIES CO., LTD 3 of 5 www.unisonic.com.tw Q W - R 1 15-011.E BLOCK DIAGRAM DRIVERS R R Q REGULATOR Σ REFERENCE REGULATOR OSCILATOR 1.4MHz/460KHz RAMP GENERATOR Current Sense Amplifier RSEN 25mΩ D Current Limit Comparator PWM ComparatorError Amplifier 1pF 27pF 400kΩ SW BST GND FB EN IN x20
UD24121 LINEAR INTEGRATED CIRCUIT UNISONIC TECHNOLOGIES CO., LTD 4 of 5 www.unisonic.com.tw Q W - R 1 15-011.E ABSOLUTE MAXIMUM RATING (TA=25°C, unless otherwise specified) PARAMETER SYMBOL RATINGS UNIT VCC Pin Voltage V IN 2 6 V SW Pin Voltage V SW 2 7 V BOOST Trap Voltage V BST V SW +6V V All Other Pins Voltage -0.3V ~ + 6V V Power Dissipation P D 568 mW Junction Temperature Range T J +150 °C Storage Temperature Range T STG -65 ~ +150 °C Notes: 1. Absolute maximum ratings are those values beyond whic h the device could be permanently damaged. Absolute maximum ratings are stress ratings only and functional device operation is not implied. RECOMMENDED OPERATING CONDITIONS PARAMETER SYMBOL RATINGS UNIT Input Supply Voltage V IN 4.5 ~ 24 V Output Voltage V OUT 0.81 ~ 15 V Ambient Temperature T A -40 ~ +125 °C input current into the EN pin 300 μA Note: The device is not guaranteed to function outside of its operating conditions. THERMAL CHARACTERISTICS PARAMETER SYMBOL RATINGS UNIT Junction To Ambient θ JA 220 °C/W Junction to Case θ JC 110 °C/W ELECTRICAL CHARACTERISTICS (VIN = 12V, TA=25°C, unless otherwise specified) PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNIT Quiescent Current I Q V EN=2V, VFB= 1 V 0 . 8 m A Shutdown Current I SHDN V EN=0V. 1 3 µA Switch-On Resistance (Note 6) R DS-ON 0 . 3 5 Ω Switch Leakage Current ISW LKG V EN=0V, VSW=0V 10 uA Current Limit (Note 6) I LIMIT 1 . 8 A Oscillation frequency F SW 1 . 4 M H z Fold-Back Frequency F SB V FB=0V 460 KHz Max Duty Cycle D MAX V FB=0.6V 87 % Minimum On Time (Note 6) T ON_MIN 100 nS Feedback Voltage V FB 4.5V≦VIN≦18V 0.790 0.810 0.830 V EN Input High Voltage V EN_H V EN Rising 1.2 V EN Input Low Voltage V EN_L 0.4 mV EN input current VEN= 2 V 2 . 1 uA VEN= 0 V 0 . 1 VIN UVLO Threshold-Rising V UVLO(Vth) V IN Rising 2.8 V VIN UVLO Threshold Hysteresis 150 mV Thermal Shutdown (Note 6) T SD 150 °C Thermal Hysteresis (Note 6) 25 °C Note: Guaranteed by design.
UD24121 LINEAR INTEGRATED CIRCUIT UNISONIC TECHNOLOGIES CO., LTD 5 of 5 www.unisonic.com.tw Q W - R 1 15-011.E TYPICAL APPLICATION CIRCUIT UTC assumes no responsibility for equipment failures that resul t from using products at values that exceed, even momentarily, rated va lues (such as maximum ratings , operating condition ranges, or other parameters) listed in products specifications of any and all UT C products described or contained herein. UTC products are not designed for use in life support appliance s, devices or systems where malfunction of these products can be reasonably expected to result in perso nal injury. Reproduction in whole or in part is prohibited without the pr ior written consent of the cop yright owner. UTC reserves the right to make changes to information published in this document, includi ng without limitation specifications and product descriptions, at any time and without notice. This docu ment supersedes and replaces all information supplied prior to the publication hereof.