SKY65152-11 SKYWORKS | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 14
Technical content
Table 1. SKY65152-11 Signal Descriptions
1 GND Ground 11 VCC3 Stage 3 collector voltage
2 GND Ground 12 N/C No connection
3 PA_ENB PA on/off control signal (on = +3 V to VCC;
13 VCC2 Stage 2 collector voltage
4 VC_BIAS Bias voltage 14 V_DET Detector output signal
5 VREF1 Bias reference voltage 1 15 VCC_DET Detector supply voltage
6 VREF2 Bias reference voltage 2 16 VCC1 Stage 1 collector voltage
7 VREF3 Bias reference voltage 3 17 GND Ground
8 GND Ground 18 RF_IN RF input
9 RF_OUT RF output 19 GND Ground
10 GND Ground 20 GND Ground
Note: The center attachment pad must have a low inductance and low thermal resistance connection to the printed circuit board groun d plane. 7, respectively). The maximum voltage for these pins is 4 V. bias to these pins when attached to a 5 V power supply. correct bias to this pin when attached to a 5 V power supply. in Table 3 and electrical specifications are provided in Table 4.
Table 2. SKY65152-11 Absolute Maximum Ratings (Note 1) parameters set at or below their nominal value. Exceeding any of the limits listed here may result in permanent damage to the device. Note 2: Voltage levels measured at the pins of the package. The Evaluation Board supply voltage levels may be different. Refer to the Evaluation Board schematic diagram in this document. or equipment, which can discharge without detection. Industry-standard ESD precautions should be used at all times. Table 3. SKY65152-11 Recommended Operating Conditions Note 1: Voltage levels measured at the pins of the package. The Evaluation Board supply voltage levels may be different. Refer to the Evaluation Board schematic diagram in this document.
Table 4. SKY65152-11 Electrical Specifications (Note 1) temperatures may reduce reliability of the device.
2442 MHz
2412 MHz
Figure 3. Gain vs Output Power Over Frequency
2462 MHz
Figure 5. EVM vs Output Power Over Frequency Figure 7. Output Power vs Enable Time Figure 4. Small Signal Gain vs Frequency Figure 6. Current vs Output Power Figure 8. Output Power vs Disable Time
Figure 9. Spectral Response @ POUT = + 30 dBm Figure 11. PAE vs Output Power Figure 13. Third Harmonic vs Output Power Figure 10. Spectral Response @ POUT = +31 dBm Figure 12. Second Harmonic vs Output Power Figure 14. Detector Voltage vs Output Power
Figure 16. SKY65152-11 Evaluation Board Assembly Diagram
Figure 17. SKY65152-11 Evaluation Board Layer Detail
Figure 20. SKY65152-11 Typical Case Markings
0.10.15 A B C
0.2 A B C
Figure 21. SKY65152-11 20-Pin MCM Package Dimensions
- Carrier tape: black conductive polystyrene
- Cover tape material: transparent conductive PSA
- Cover tape size: 9.3 mm width
- All dimensions are in millimeters
- Pin 1 orientation is in top left corner for the following Skyworks products:
Figure 22. SKY65152-11 20-Pin MCM Tape and Reel Dimensions
DATA SHEET • SKY65152-11 POWER AMPLIFIER Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 14 October 19, 2009 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Not ice • 200968F
Ordering Information
Model Name Manufacturing Part Number Evaluation Kit Part Number SKY65152-11 WLAN Power Amplifier SKY65152-11 (Pb-free package) TW16-D280-031 Copyright © 2009 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks, the Skyworks symbol, and “Breakthrough Simplicity” are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference.