TSSP6P38_V01 VISHAY | Alldatasheet

Document overview

  • Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
  • PDF pages: 13

Technical content

www.vishay.com Vishay Semiconductors Datasheet Values Refer to PCN-OPT-1224-2022 Rev. 2.4, 17-Aug-2022 1 Document Number: 82475 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 IR Mid Range Proximity Sensor LINKS TO ADDITIONAL RESOURCES

DESCRIPTION

The TSSP6P38 is a compact infrared detector module for proximity sensing application. It receives 38 kHz modulated signals and has a peak sensitivity of 940 nm. The length of the detector’s output pulse varies in proportion to the amount of light reflected from the object being detected.

FEATURES

  • Up to 2 m for proximity sensing
  • Receives 38 kHz modulated signal
  • Photo detector and preamplifier in one package
  • Low supply current
  • Shielding against EMI
  • Visible light is suppressed by IR filter
  • Supply voltage: 2.0 V to 5.5 V
  • Insensitive to supply voltage ripple and noise
  • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912

APPLICATIONS

  • Object approach detection for activation of displays and user consoles, signaling of alarms, etc.
  • Simple gesture controls
  • Differentiation of car arri val, static, car departure in parking lots
  • Reflective sensors for toilet flush
  • Navigational sensor for robotics DESIGN SUPPORT TOOLS
  • 3D models
  • Window size calculator BLOCK DIAGRAM 23204 23204 Product Page Marking 33 kΩ VS OUTDemo- GND passAGCInput PIN Band dulator Control circuit 16833_19

www.vishay.com Vishay Semiconductors Datasheet Values Refer to PCN-OPT-1224-2022 Rev. 2.4, 17-Aug-2022 2 Document Number: 82475 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 MECHANICAL DATA Pinning 1 = GND, 2 = N.C., 3 = V S, 4 = OUT ORDERING CODE Taping: TSSP6P38TT - top view taped, 1190 pcs/reel TSSP6P38TR - side view taped, 1120 pcs/reel PROXIMITY SENSING Note

  • Other frequencies available by request Note
  • Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress ratin g only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability 23205 +3 V IR emitter +3 V 38 kHz Envelope signal Out to μC IR detector PARTS TABLE Carrier frequency 38 kHz TSSP6P38 Package Panhead Pinning 1 = GND, 2 = N.C., 3 = V S, 4 = OUT Dimensions (mm) 7.5 W x 5.3 H x 4.0 D Mounting SMD Application Proximity sensors Special options • Narrow optical filter: www.vishay.com/doc?81590
  • Wide optical flter: www.vishay.com/doc?82726 ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITION SYMBOL VALUE UNIT Supply voltage (pin 3) V S -0.3 to +6 V Supply current (pin 3) I S 5m A Output voltage (pin 4) V O -0.3 to 5.5 V Voltage at output to supply V S - VO -0.3 to (VS + 0.3) V Output current (pin 4) I O 5m A Junction temperature T j 100 °C Storage temperature range T stg -25 to +85 °C Operating temperature range T amb -25 to +85 °C Power consumption T amb ≤ 85 °C P tot 10 mW

www.vishay.com Vishay Semiconductors Datasheet Values Refer to PCN-OPT-1224-2022 Rev. 2.4, 17-Aug-2022 3 Document Number: 82475 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) Fig. 1 - Output Active Low Fig. 2 - Pulse Length and Sensitivity in Dark Ambient Fig. 3 - Frequency Dependence of Responsivity Fig. 4 - Sensitivity in Bright Ambient ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT Supply current (pin 3) E e = 0, VS = 3.3 V I SD 0.25 0.35 0.45 mA Ev = 40 klx, sunlight I SH -0 . 4 5- m A Supply voltage V S 2.0 - 5.5 V Receiving distance Direct line of sight, test signal see Fig. 1, IR diode TSAL6200, IF = 50 mA d- 2 1 - m Output voltage low (pin 4) IOSL = 0.5 mA, Ee = 0.7 mW/m2, test signal see Fig. 1 VOSL - - 100 mV Minimum irradiance Pulse width tolerance: tpi - 5/fo < tpo < tpi + 5/fo, test signal see Fig. 1 Ee min. - 0.15 0.3 mW/m 2 Maximum irradiance Pulse width tolerance: tpi - 5/fo < tpo < tpi + 5/fo, test signal see Fig. 1 Ee max. 30 - - W/m 2 Directivity Angle of half receiving distance ϕ1/2 -± 4 5- ° Ee T tpi (1) t VO VOH VOL t Optical Test Signal (IR diode TSAL6200, 30 pulses, f = f 0, T = 10 ms) Output Signal td (2) tpo (3) (3) tpi - 5/f0 < tpo < tpi + 5/f0 16110-17 (1) tpi ≥ 16/f0 100 1000 10000 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 0.1 10 1000 100 000 Axis Title 1st line 2nd line 2nd line tpo - Output Pulse Width (ms) Ee - Irradiance (mW/m2) Output pulse width Input burst length λ= 9 5 0 n m , optical test signal, Fig. 1 0.0 0.2 0.4 0.6 0.8 0.9 1.0 25 30 45 50 f/f0 - Relative Frequency E /E - Rel. Responsivitye min. e 4035 0.1 0.3 0.5 0.7 f = f0 ± 5 % Δf (3 dB) = f0/10 100 1000 10000 0.01 0.1 1 10 100 Axis Title 1st line 2nd line 2nd line Ee min. - Threshold Irradiance (mW/m2) Ee - Ambient DC Irradiance (W/m2) Correlation with ambient light sources:

10 W/m

2 = 1.4 klx (std. ilum. A, T = 2855 K) 10 W/m2 = 8.2 klx (daylight, T = 5900 K) Wavelength of ambient illumination: λ = 950 nm

www.vishay.com Vishay Semiconductors Datasheet Values Refer to PCN-OPT-1224-2022 Rev. 2.4, 17-Aug-2022 4 Document Number: 82475 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Fig. 5 - Sensitivity vs. Supply Voltage Disturbances Fig. 6 - Maximum Output Pulse Width vs. Irradiance Fig. 7 - Sensitivity vs. Ambient Temperature Fig. 8 - Relative Spectral Sensitivity vs. Wavelength Fig. 9 - Angle Characteristic Fig. 10 - Max. Rate of Bursts 100 1000 10000 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 11 0 1 0 0 1 0 0 0 Axis Title 1st line 2nd line 2nd line Ee min. - Threshold Irradiance (mW/m2) ∆VS RMS - AC Voltage on DC Supply Voltage (mV) f = 100 Hz f = 10 kHz f = 30 kHz f = f0 100 1000 10000 100 150 200 250 0.1 1 10 100 Axis Title 1st line 2nd line 2nd line tpo - Output Pulse Width (ms) Ee - Irradiance (mW/m2) dark

1 W/m² ambient DC light

10 W/m² ambient DC light

burst length 200ms, burst repetition time 1s 100 1000 10000 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 -30 -10 10 30 50 70 90 Axis Title 1st line 2nd line 2nd line Ee min. - Threshold Irradiance (mW/m2) Tamb - Ambient Temperature (°C) 100 1000 10000 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 750 850 950 1050 1150 Axis Title 1st line 2nd line 2nd line S(λ)rel. - Relative Spectral Sensitivity λ - Wavelength (nm)21425 0.2 0.4 0.6 0.8 1.0 1.2 -90 90 Angle (°) 70503010-10-30-50-70 Relative Response Distance Directivity Characteristic of a Reflective Sensor using VSMB3940X01 and TSSP6P38 tpi (ms) trepeat min. (ms) 100 200 300 400 500 600 700 800 0 20 40 60 80 100 120 140 160 180

www.vishay.com Vishay Semiconductors Datasheet Values Refer to PCN-OPT-1224-2022 Rev. 2.4, 17-Aug-2022 5 Document Number: 82475 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Fig. 11 - tpo vs. Distance Kodak Gray Card Plus 15 % Fig. 12 - Dynamic Rang e of Sensor vs. tpi The typical application of the TSSP6P38 is a reflective sensor with analog information contained in its output. Such a sensor is evaluating the time required by the AGC to suppress a quasi continuous signal. The time required to suppress such a signal is longer when the signal is strong than when the signal is weak, resulting in a pulse length corresponding to the distance of an object from the sensor. This kind of analog information can be evaluated by a microcontroller. The absolute amount of reflected light depends much on th e environment and is not evaluated. Only sudden changes of the amount of reflected light, and therefore changes in the pulse width, are evaluated using this application. Example of a signal pattern: Example for a sensor hardware: There should be no common window in front of the emitter and receiver in order to avoid crosstalk by guided light through the window. The logarithmic characteristic of the AGC in the TSSP6P38 results in an almost linear relationship between distance and pulse width. Ambient light has also some impact to the pulse width of this kind of sensor, making the pulse shorter. Response Distance (m) tpo (ms) 100 120 IF = 100 mA IF = 50 mAIF = 30 mAIF = 10 mA Emitter: VSMB1940X01 tpi (ms) dmax./dmin. 10 20 30 40 110 120 1009080706050 Optical signal Response of the TSSP6P38 (strong reflection) trepeat = 500 ms tpi = 120 ms, 38 kHz Response of the TSSP6P38 (weak reflection) Emitter TSAL6200 IR Receiver TSSP6P38 Separation to avoid crosstalk by stray light inside the housing

www.vishay.com Vishay Semiconductors Datasheet Values Refer to PCN-OPT-1224-2022 Rev. 2.4, 17-Aug-2022 6 Document Number: 82475 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 PACKAGE DIMENSIONS in millimeters 2.35 R 1.7 5.51 0.5 ± 0.15 3 x 1.27 = 3.81 2.6 7.5 7.2 1.27 5.3 2.9 2.2 Pick and place area. TR taping 2.2 3 x 1.27 = 3.81 1.27 0.9 2.8 specifications according to DIN technical drawings Not indicated tolerances ± 0.3 Pick and place area. TT taping Footprint (1.5) (1.4) Issue: 8; 02.09.09 16776 Drawing-No.: 6.544-5341.01-4 A A 0.1 0.1 0.3 0.4

www.vishay.com Vishay Semiconductors Datasheet Values Refer to PCN-OPT-1224-2022 Rev. 2.4, 17-Aug-2022 7 Document Number: 82475 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 ASSEMBLY INSTRUCTIONS Reflow Soldering

  • Reflow soldering must be done within 72 h while stored under a max. tempera ture of 30 °C, 60 % RH after opening the dry pack envelope
  • Set the furnace temperatures for pre-heating and heating in accordance with the reflow temperature profile as shown in the diagram. Exercise extreme care to keep the maximum temperature below 260 °C. The temperature shown in the profile means the temperature at the device surface. Since there is a temperature difference between the component and the circuit board, it should be verified that the temperature of the device is accurately being measured
  • Handling after reflow should be done only after the work surface has been cooled off Manual Soldering
  • Use a soldering iron of 25 W or less. Adjust the temperature of the soldering iron below 300 °C
  • Finish soldering within 3 s
  • Handle products only after the temperature has cooled off VISHAY LEAD (Pb)-FREE REFLOW SOLDER PROFILE 19800 100 1000 10000 100 150 200 250 300 0 5 0 1 0 01 5 02 0 02 5 03 0 0 Axis Title 1st line 2nd line 2nd line Temperature (°C) Time (s) max. 120 s max. 100 s max. 20 s Max. ramp up 3 °C/s max. 260 °C 245 °C 217 °C 240 °C 255 °C Max. ramp down 6 °C/s Max. 2 cycles allowed

www.vishay.com Vishay Semiconductors Datasheet Values Refer to PCN-OPT-1224-2022 Rev. 2.4, 17-Aug-2022 8 Document Number: 82475 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TAPING VERSION TSSP..TT DIMENSIONS in millimeters 16584

www.vishay.com Vishay Semiconductors Datasheet Values Refer to PCN-OPT-1224-2022 Rev. 2.4, 17-Aug-2022 9 Document Number: 82475 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TAPING VERSION TSSP..TR DIMENSIONS in millimeters 16585

www.vishay.com Vishay Semiconductors Datasheet Values Refer to PCN-OPT-1224-2022 Rev. 2.4, 17-Aug-2022 10 Document Number: 82475 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 REEL DIMENSIONS in millimeters LEADER AND TRAILER DIMENSIONS in millimeters 16734 Trailer Leader no devices min. 200 min. 400 StartEnd devices 96 11818 no devices

www.vishay.com Vishay Semiconductors Datasheet Values Refer to PCN-OPT-1224-2022 Rev. 2.4, 17-Aug-2022 11 Document Number: 82475 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 OUTER PACKAGING The sealed reel is packed into a pizza box. COVER TAPE PEEL STRENGTH According to DIN EN 60286-3 0.1 N to 1.3 N 300 mm/min. ± 10 mm/min. 165° to 180° peel angle LABEL Standard bar code labels for finished goods The standard bar code labels are product labels and used for identification of goods. The finished goods are packed in final packing area. The standard packing units are labeled with standard bar code labels before transported as finished goods to warehouses. The labels are on each packing unit and contain Vishay Semiconductor GmbH specific data. CARTON BOX DIMENSIONS in millimeters THICKNESS WIDTH LENGTH Pizza box (SMD and Heimdall) (taping in reels) 50 340 340 Thickness Width 22127 Length VISHAY SEMICONDUCTOR GmbH STANDARD BAR CODE PRODUCT LABEL (finished goods) PLAIN WRITING ABBREVIATION LENGTH Item-description - 18 Item-number INO 8 Selection-code SEL 3 LOT-/serial-number BATCH 10 Data-code COD 3 (YWW) Plant-code PTC 2 Quantity QTY 8 Accepted by ACC - Packed by PCK - Mixed code indicator MIXED CODE - Origin xxxxxxx+ Company logo LONG BAR CODE TOP TYPE LENGTH Item-number N 8 Plant-code N 2 Sequence-number X 3 Quantity N 8 Total length - 21 SHORT BAR CODE BOTTOM TYPE LENGTH Selection-code X 3 Data-code N 3 Batch-number X 10 Filter - 1 Total length - 17

www.vishay.com Vishay Semiconductors Datasheet Values Refer to PCN-OPT-1224-2022 Rev. 2.4, 17-Aug-2022 12 Document Number: 82475 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 DRY PACKING The reel is packed in an anti-humidity bag to protect the devices from absorbing moisture during transportation and storage. FINAL PACKING The sealed reel is packed into a cardboard box. RECOMMENDED METHOD OF STORAGE Dry box storage is recommended as soon as the aluminum bag has been opened to preve nt moisture absorption. The following conditions should be observed, if dry boxes are not available:

  • Storage temperature 10 °C to 30 °C
  • Storage humidity ≤ 60 % RH max. After more than 72 h under these conditions moisture content will be too high for reflow soldering. In case of moisture absorptio n, the devices will recover to the former condition by drying under the following condition: 192 h at 40 °C + 5 °C / - 0 °C and < 5 % RH (dry air / nitrogen) or 96 h at 60 °C + 5 °C and < 5 % RH for all device containers or 24 h at 125 °C + 5 °C not suitable for reel or tubes. An EIA JEDEC ® standard J-STD-020 level 4 label is included on all dry bags. EIA JEDEC standard J-STD-020 level 4 label is included on all dry bags ESD PRECAUTION Proper storage and handling procedures should be followed to prevent ESD damage to the devices especially when they are removed from the antistatic shielding bag. Electrostatic sensitive devices warning labels are on the packaging. VISHAY SEMICONDUCTORS STANDARD BAR CODE LABELS The Vishay Semiconductors st andard bar code labels are printed at final packing areas. The labels are on each packing unit and contain Vishay Semiconductors specific data. Aluminum bag Label Reel 15973 CAUTION This bag contains MOISTURE-SENSITIVE DEVICES 1. Shelf life in sealed bag: 12 months at < 40 °C and < 90 % relative humidity (RH) 2. After this bag is opened, devices that will be subjected to soldering reflow or equivalent processing (peak package body temp. 260 °C) must be 2a. Mounted within 72 hours at factory condition of < 30 °C/60 % RH or 2b. Stored at < 5 % RH 3. Devices require baking befor mounting if: Humidity Indicator Card is > 10 % when read at 23 °C ± 5 °C or 2a. or 2b. are not met. 4. If baking is required, devices may be baked for: 192 hours at 40 °C + 5 °C/- 0 °C and < 5 % RH (dry air/nitrogen) or 96 hours at 60 °C ± 5 °C and < 5 % RH for all device containers or 24 hours at 125 °C ± 5 °C not suitable for reels or tubes Bag Seal Date: (If blank, see barcode label) Note: Level and body temperature defined by EIA JEDEC Standard J-STD-020 LEVEL 22522 22645

www.vishay.com Vishay Revision: 01-Jan-2022 1 Document Number: 91000 Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA AR E SUBJECT TO CHANGE WITH OUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product , (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all implied warranties, incl uding warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of pro ducts for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in ge neric applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specificat ions may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and for informational purposes only. Inclusion of these hyperlinks does not constitute an endorsement or an approval by Vishay of any of the products, services or opinions of the corporation, organization or individual associated with the third-party website. Vishay disclaims any and all liability and bears no responsibility for the accuracy, legality or content of the third-party web site or for that of subsequent links. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. © 2022 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED