TSH10 STMICROELECTRONICS | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 5

Technical content

■ LOW NOISE : 6nV/√Hz ■ GAIN BANDWIDTH PRODUCT : 140MHz ■ UNITY GAIN STABLE ■ SLEW RATE : 150V/µs ■ STANDARD PIN OUT

DESCRIPTION

The TSH10 is a low cost wide bandwidth single operational amplifier featuring low input noise of 6nV/√Hz. Other features as unity gain stability, fast settling time and high linearity make it suitable for any application requiring speed and precision as high resolution video or DAC buffer. ORDER CODE D = Small Outline Package (SO) - also available in Tape & Reel (DT) PIN CONNECTIONS (top view) Part Number Temperature Range Package D TSH10I -40°C, +125°C • D SO8 (Plastic Micropackage) 7Inverting Input Non-inverting Input Output Offset Null 2Offset Null 1 N.C. VCC VCC TSH10 140MHz BANDWIDTH LOW NOISE SINGLE OPERATIONAL AMPLIFIER October 2000

INPUT OFFSET VOLTAGE NULL CIRCUIT MAXIMUM RATINGS OPERATING CONDITIONS non inverting input inverting input 1 8 Offset N1 Offset N2

7 VCC

V Internal ref N1 N2 TSH10 100k/C87 VCC Symbol Parameter Value Unit VCC Supply Voltage ±7 V Vid Differential Input Voltage ±5 V Vi Input Voltage ±5 V Iin Current On Inputs Current On Offset Null Pins ±50 ±20 V Toper Operating Free-Air Temperature range -40 to +125 °C Tstg Storage Temperature Range -65 to +150 °C Symbol Parameter Value Unit VCC Supply Voltage ±3 to ±6 V Vic Common Mode Input Voltage Range VCC - +2 to VCC + -1 V

ELECTRICAL CHARACTERISTICS

VCC = ±5V, Tamb = 25°C (unless otherwise specified) Symbol Parameter Min. Typ. Max. Unit Vio Input Offset Voltage 1 10 mV DV io Input Offset Voltage Drift Tmin. ≤ Tamb ≤ Tmax. 20 µV/°C Iib Input Bias Current. 53 0 µA Iio Input Offset Current. 0.1 10 µA ICC Supply Current, no load V CC = ±5V 20 40 mA Avd Large Signal Voltage Gain Vo = ±2.5V R L = 100Ω 200 800 V/V Vicm Input Common Mode Voltage Range -3 to +4 -3.5 to +4.5 V CMR Common-mode Rejection Ratio Vic = Vicm min. 55 100 V SVR Supply Voltage Rejection Ratio VCC = ±5V to ±3V 45 70 dB Vo Output Voltage R L = 100Ω ±2.5 +3.5 -3.7 V Io Output Short Circuit Current Vid = ±1V, Vo = 0V ±70 mA GBP Gain Bandwidth Product AVCL = 100, RL = 100Ω , f = 7.5MHz 140 MHz SR Slew Rate V in = ±2V, AVCL = 1, RL = 100Ω 150 V/µs en Equivalent Input Voltage Noise f = 1MHz 6 nV/ √Hz φm Phase Margin A VM = 1, RL = 100Ω , CL = 15pF 40 Degrees

As for any high frequency device, a few rules must be observed when designing the PCB to get the best performances from this high speed op amp. From the most to the least important points : ❑ Each power supply lead has to be by- passed to ground with a 10nF ceramic ca- pacitor very close to the device and a 10µF tantalum capacitor. ❑ To provide low inductance and low resist- ance common return, use a ground plane or common point return for power and sig- nal. ❑ All leads must be wide and as short as pos- sible especially for op amp inputs. This is in order to decrease parasitic capacitance and inductance. ❑ Use small resistor values to decrease time constant with parasitic capacitance. Be aware on TSH10 device of the Iio error and input noise currents with high feedback re- sistor values. ❑ Choose component sizes as small as pos- sible (SMD). ❑ On output, decrease capacitor load so as to avoid circuit stability being degraded which may cause oscillation. You can also add a serial resistor in order to minimise its influence. ❑ One can add in parallel with feedback re- sistor a few pF ceramic capacitor C F adjust- ed to optimize the settling time. Input 1k/C87 10nF 10mF C F -5V +5V 10nF 10/C109F Output 50/C87 1k/C87 50/C87

Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. © The ST logo is a registered trademark of STMicroelectronics © 2000 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom © http://www.st.com PACKAGE MECHANICAL DATA

8 PINS - PLASTIC MICROPACKAGE (SO)

Dim. Millimeters Inches A 1.75 0.069 a1 0.1 0.25 0.004 0.010 a2 1.65 0.065 a3 0.65 0.85 0.026 0.033 b 0.35 0.48 0.014 0.019 b1 0.19 0.25 0.007 0.010 C 0.25 0.5 0.010 0.020 c1 45° (typ.) D 4.8 5.0 0.189 0.197 E 5.8 6.2 0.228 0.244 e 1.27 0.050 e3 3.81 0.150 F 3.8 4.0 0.150 0.157 L 0.4 1.27 0.016 0.050 M 0.6 0.024 S 8° (max.)