TS339C

TS339C STMICROELECTRONICS | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 6

Technical content

TS339C,I,M MICROPOWER QUAD CMOS VOLTAGE COMPARATORS .EXTREMELY LOW SUPPLY CURRENT : 9µA TYP / COMPARATOR .WIDE SINGLE SUPPLY RANGE (3V TO 16V) OR DUAL SUPPLIES (±1.5V TO ±8V) .EXTREMELY LOW INPUT BIAS CURRENT : 1pA TYP .EXTREMELY LOW INPUT OFFSET CURRENT : 1pA TYP .INPUT COMMON-MODE VOLTAGE RANGE INCLUDES GND .HIGH INPUT IMPEDANCE : 1012Ω TYP .FAST RESPONSE TIME : 1.5µs TYP FOR 5mV OVERDRIVE .PIN-TO-PIN AND FUNCTIONALLY COMPATIBLE WITH BIPOLAR LM339 Inverting Input 2 Output 2 Non-inverting Input 2 Output 1 Inverting Input 1 Non-inverting Input 1 CCV - CCV Output 3 Output 4 Non-inverting Input 4 Inverting Input 4 Non-inverting Input 3 Inverting Input 3 PIN CONNECTIONS (top view) N DIP14 (Plastic Package) D SO14 (Plastic Micropackage) September 1998 ORDER CODES Part Number Temperature Range Package NDP TS339C 0 oC, +70oC lll TS339I -40 oC, +125oC lll TS339M -55 oC, +125oC lll Example :TS339CN

DESCRIPTION

The TS339 is a micropower CMOS quad voltage comparator with extremely low consumption of 9µA typ / comparator (20 times less than bipolar LM339). Similar performances are offered by the quad micropower comparator TS3704 with a push- pull CMOS output. Thus response times remain similar to the LM339. P TSSOP14 (Thin Shrink Small Outline Package)

Symbol Parameter Value Unit VCC + Supply Voltage - (note 1) 18 V Vid Differential Input Voltage - (note 2) ±18 V Vi Input Voltage - (note 3) 18 V VO Output Voltage 18 V IO Output Current 20 mA Toper Operating Free-Air Temperature Range TS339C TS339I TS339M 0 to +70 -40 to +125 -55 to +125 oC Tstg Storage Temperature Range -65 to +150 oC Notes :1. All voltage values, except differential voltage, are with respect to network ground terminal. 2. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal. 3. The magnitude of the input and the output voltages must never exceed the magnitude of the positive supply voltage. 4. Short circuit from outputs to V CC + can cause excessive heating and eventual destruction. OPERATING CONDITIONS Symbol Parameter Value Unit VCC + Supply Voltage TS339C,I TS339M 3t o1 6 4t o1 6 V Vicm Common Mode Input Voltage Range 0 to V CC + -1.5 V T1 T2 TT34 R T T T T T T T T12 T17 T13 TT14 15 T16 T T T18 Input - Input + Output CCV+ CCV- SCHEMATIC DIAGRAM (for 1/4 TS339) TS339C,I,M

ELECTRICAL CHARACTERISTICS

VCC + = 5V, VCC - = 0V, Tamb =2 5°C (unless otherwise specified) Symbol Parameter Min. Typ. Max. Unit Vio Input Offset Voltage - (note 1) Vic=V icm min.,VCC + = 5V to 10V Tmin.≤ Tamb ≤ Tmax . 1.4 5 6.5 mV Iio Input Offset Current - (note 2) Vic= 2.5 V Tmin.≤ Tamb ≤ Tmax . 300 pA Iib Input Bias Current - (note 2) Vic= 2.5 V Tmin.≤ Tamb ≤ Tmax . 600 pA Vicm Input Common Mode Voltage Range Tmin.≤ Tamb ≤ Tmax . 0t oVCC + -1.2 0t oVCC + -1.5 V CMR Common-mode Rejection Ratio Vic=V icm min.7 5 dB SVR Supply Voltage Rejection Ratio VCC + = +5V to +10V 85 dB IOH High Level Output Current Vid=1 V , VOH = +5V Tmin.≤ Tamb ≤ Tmax . 24 0 1000 nA VOL Low Level Output Voltage Vid= -1V, IOL = 6mA Tmin.≤ Tamb ≤ Tmax . 350 400 650 mV ICC Supply Current (4 comparators) No load - Outputs low Tmin.≤ Tamb ≤ Tmax . 36 80 100 µA tPLH Response Time Low to High Vic= 0V, f = 10kHz, RL = 5.1kΩ ,C L = 15pF, Overdrive = 5mV Overdrive = 10mV Overdrive = 20mV Overdrive = 40mV TTL Input 1.5 1.2 1.1 0.9 0.8 µs t PHL Response Time High to Low Vic= 0V, f = 10kHz, RL = 5.1kΩ ,C L = 15pF, Overdrive = 5mV Overdrive = 10mV Overdrive = 20mV Overdrive = 40mV TTL Input 2.5 1.9 1.2 0.8 0.08 µs t f Fall Time f = 10kHz, CL = 15pF, RL = 5.1kΩ , Overdrive 50mV 25 ns Note : 1. The specified offset voltage is the maximun value required to drive the output up to 4.5V or down to 0.3V. 2. Maximum values including unavoidable inaccuracies of the industrial test. TS339C,I,M

PM-DIP14.EPS PACKAGE MECHANICAL DATA

14 PINS - PLASTIC DIP

Dimensions Millimeters Inches a1 0.51 0.020 B 1.39 1.65 0.055 0.065 b 0.5 0.020 b1 0.25 0.010 D 20 0.787 E 8.5 0.335 e 2.54 0.100 e3 15.24 0.600 F 7.1 0.280 i 5.1 0.201 L 3.3 0.130 Z 1.27 2.54 0.050 0.100 DIP14.TBL TS339C,I,M

PM-SO14.EPS PACKAGE MECHANICAL DATA

14 PINS - PLASTIC MICROPACKAGE (SO)

Dimensions Millimeters Inches A 1.75 0.069 a1 0.1 0.2 0.004 0.008 a2 1.6 0.063 b 0.35 0.46 0.014 0.018 b1 0.19 0.25 0.007 0.010 C 0.5 0.020 c1 45 o (typ.) D 8.55 8.75 0.336 0.334 E 5.8 6.2 0.228 0.244 e 1.27 0.050 e3 7.62 0.300 F 3.8 4.0 0.150 0.157 G 4.6 5.3 0.181 0.208 L 0.5 1.27 0.020 0.050 M 0.68 0.027 o (max.) SO14.TBL TS339C,I,M

Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for useas criticalcomponents in life support devices or systems without express written approval of STMicroelectronics.  The ST logo is a trademark of STMicroelectronics  1998 STMicroelectronics – Printed in Italy – All Rights Reserve d STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - France - Germany - Italy - Japan - Korea - Malaysia - Malta - Mexico - Morocco The Netherlands - Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A. ORDER CODE : PACKAGE MECHANICAL DATA

14 PINS - THIN SHRINK SMALL OUTLINE PACKAGE

Dim. Millimeters Inches A 1.20 0.05 A1 0.05 0.15 0.01 0.006 b 0.19 0.30 0.007 0.15 c 0.09 0.20 0.003 0.012 E 6.40 0.252 e 0.65 0.025 o 8o 0o 8o TS339C,I,M