TS30111 ETC2 | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 23

Technical content

  • 1 - TS30111 Version 1.0 Specifications subject to change WWW.TRIUNESYSTEMS.COM Copyright © 2012, Triune Systems, LLC TS30111 VOUT Adjustable Output PGND VSW VCC FB GND BST VCC PG PG RTOP RBOT 10 kohm (optional) VOUT ENEN CBYPASS CBST LOUT COUT TS30111 VOUT Fixed Output EN PGND VSW VCC FB GND VCC EN PG PG 10 kohm (optional) VOUT BST The TS30 111 is a DC/DC synchronous switching regulator with fully integrated power switches, internal compensation, and full fault protection. The switching frequency of 1MHz enables the use of small filter components resulting in minimal board space and reduced BOM costs. The TS30 111 utilizes current mode feedback in normal regulation PWM mode. When the regulator is placed in standby (EN is low), the device draws less than 10uA quiescent current. The TS30 111 integrates a wid e range of protection circuitry including input supply under -voltage lockout, output voltage soft start, current limit, and thermal shutdown. The TS30111 includes supervisory reporting through the PG (Power Good) open drain output to interface other components in the system.

APPLICATIONS

 On-card switching regulators  Set-top box, DVD, LCD, LED supply  Industrial power supplies  Fixed output voltage choices: 1.5V, 1.8V, 2.5V, 3.3V, and 5V Adjustable version output voltage range: 0.8V to 5V  Wide input voltage range 4.5V to 16V (18V Abs Max)  1MHz +/- 10% fixed switching frequency  Continuous output current: 700mA  High efficiency – up to 90%  Current mode PWM control with PFM mode for improved light load efficiency  Voltage supervisor for VOUT reported at the PG pin  Input supply under voltage lockout  Soft start for controlled startup with no overshoot  Full protection for over-current, over-temperature, and VOUT over-voltage  Less than 10uA in standby mode  Low external component count SUMMARY SPECIFICATION  Junction operating temperature -40 °C to 125 °C  Packaged in a 16pin QFN (3x3) High Efficiency 700mA Current-Mode Synchronous Buck DC/DC Converter, 1MHz DESCRIPTION FEATURES TYPICAL APPLICATIONS

  • 2 - TS30111 Version 1.0 Specifications subject to change WWW.TRIUNESYSTEMS.COM Copyright © 2012, Triune Systems, LLC PINOUT VCC VCC GND VSW VCC BST EN VSW PGND PGND VSW VSW NC NC FB PG TS30111 PIN 1 Figure 1: 16 Lead 3x3 QFN, Top View PIN DESCRIPTION FOR 16 LEAD 3X3 QFN Pin Symbol Pin # Function Description VSW 1 Switching Voltage Node Connected to 3.3uH (typical) inductor VCC 2 Input Voltage Input voltage VCC 3 Input Voltage Input voltage GND 4 GND Primary ground for the majority of the device except the low-side power FET FB 5 Feedback Input Regulator FB Voltage. Connects to VOUT for fixed mode and the output resistor divider for adjustable mode NC 6 No Connect Not Connected NC 7 No Connect Not Connected PG 8 Power Good Output Open-drain output EN 9 Enable Input Above 2.2V the device is enabled. GND the pin to put device in standby mode. Includes internal pull-up BST 10 Bootstrap Capacitor Bootstrap capacitor for the high-side FET gate driver. 22nF ceramic capacitor from BST pin to VSW pin VCC 11 Input Voltage Input Voltage VSW 12 Switching Voltage Node Connected to 3.3uH (typical) inductor VSW 13 Switching Voltage Node Connected to 3.3uH (typical) inductor PGND 14 Power GND GND supply for internal low-side FET/integrated diode PGND 15 Power GND GND supply for internal low-side FET/integrated diode VSW 16 Switching Voltage Node Connected to 3.3uH (typical) inductor
  • 4 - TS30111 Version 1.0 Specifications subject to change WWW.TRIUNESYSTEMS.COM Copyright © 2012, Triune Systems, LLC ABSOLUTE MAXIMUM RATINGS Over operating free–air temperature range unless otherwise noted(1, 2) Parameter Value Unit VCC -0.3 to 18 V BST -0.3 to (VCC+6) V VSW -1 to 18 V EN, PG,FB -0.3 to 6 V Electrostatic Discharge – Human Body Model +/-2k V Electrostatic Discharge – Charge Device Model +/-500 V Lead Temperature (soldering, 10 seconds) 260 C (1) Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress rati ngs only and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is n ot implied. Exposure to absolute–maximum–rated conditions for extended periods may affect device reliability. (2) All voltage values are with respect to network ground terminal. THERMAL CHARACTERISTICS Symbol Parameter Value Unit JA Thermal Resistance Junction to Air (Note 1) 38 °C/W TSTG Storage Temperature Range -65 to 150 °C TJ MAX Maximum Junction Temperature 150 °C TJ Operating Junction Temperature Range -40 to 125 °C Note 1: Assumes 16LD 3x3 QFN with hi-K JEDEC board and 13.5 inch2 of 1 oz Cu RECOMMENDED OPERATING CONDITIONS Symbol Parameter Min Typ Max Unit VCC Input Operating Voltage 4.5 12 16 V CBST Bootstrap Capacitor 17.6 22 26.4 nF LOUT Output Filter Inductor Typical Value (Note 1) 3.3 uH COUT Output Filter Capacitor Typical Value (Note 2) 22 uF COUT-ESR Output Filter Capacitor ESR 2 100 m CBYPASS Input Supply Bypass Capacitor Typical Value (Note 3) 8 10 uF Note 1: For best performance, an inductor with a saturation current rating higher than the maximum VOUT load requirement plus the inductor current ripple. Note 2: For best performance, a low ESR ceramic capacitor should be used. Note 3: For best performance, a low ESR ceramic capacitor should be used. If CBYPASS is not a low ESR ceramic capacitor, a 0.1uF ceramic capacitor should be added in parallel to CBYPASS.
  • 5 - TS30111 Version 1.0 Specifications subject to change WWW.TRIUNESYSTEMS.COM Copyright © 2012, Triune Systems, LLC

ELECTRICAL CHARACTERISTICS

Electrical Characteristics, TJ = -40C to 125C, VCC = 12V (unless otherwise noted) Symbol Parameter Condition Min Typ Max Unit VCC Supply Voltage VCC Input Supply Voltage 4.5 16 V ICC-NORM Quiescent current Normal Mode VCC = 12V, ILOAD = 0A 5.2 mA ICC-NOSWITCH Quiescent current Normal Mode – Non-switching VCC=12V, ILOAD=0A, Non-switching 2.3 mA ICC-STBY Quiescent current Standby Mode VCC = 12V, EN = 0V 5 10 uA VCC Under Voltage Lockout VCC-UV Input Supply Under Voltage Threshold VCC Increasing 4.3 V VCC-UV_HYST Input Supply Under Voltage Threshold Hysteresis 650 mV OSC FOSC Oscillator Frequency 1 MHz PG Open Drain Output TPG PG Release Timer 10 ms IOH-PG High-Level Output Leakage VPG = 5V 0.5 uA VOL-PG Low-Level Output Voltage IPG = -0.3mA 0.01 V EN Input Voltage Thresholds VIH-EN High Level Input Voltage 2.2 V VIL-EN Low Level Input Voltage 0.8 V VHYST-EN Input Hysteresis 480 mV IIN-EN Input Leakage VEN=5V 3.5 uA VEN=0V -1.5 uA Thermal Shutdown TSD Thermal Shutdown Junction Temperature Note: not tested in production 150 170 °C TSDHYST TSD Hysteresis Note: not tested in production 10 °C

  • 6 - TS30111 Version 1.0 Specifications subject to change WWW.TRIUNESYSTEMS.COM Copyright © 2012, Triune Systems, LLC REGULATOR CHARACTERISTICS Electrical Characteristics, TJ = -40C to 125C, VCC = 12V (unless otherwise noted) Symbol Parameter Condition Min Typ Max Unit Switch Mode Regulator: L=3.3uH and C=22uF VOUT-PWM Output Voltage Error in PWM Mode ILOAD =700 mA ±2% V VOUT-PFM Output Voltage Tolerance in PFM Mode ILOAD = 0A VOUT + 1% V RDSON High Side Switch On Resistance IVSW = -700mA (Note 1) 240 mΩ Low Side Switch On Resistance IVSW = 700mA (Note 1) 160 mΩ IOUT Output Current TS30111 700 mA IOCD Over Current Detect HS switch current TS30111 1.2 A FBTH Feedback Reference (Adjustable Mode) (Note 3) 0.8 V FBTH-TOL Feedback Reference Absolute Tolerance (Note 3) 1.5 % TSS Soft start Ramp Time 4 ms FBTH-PFM PFM Mode FB Comparator Threshold VOUT + V VOUT-UV VOUT Under Voltage Threshold 93% VOUT VOUT-UV_HYST VOUT Under Voltage Hysteresis 1.5% VOUT VOUT-OV VOUT Over Voltage Threshold 103% VOUT VOUT-OV_HYST VOUT Over Voltage Hysteresis 1% VOUT DUTYMAX Max Duty Cycle (Note 2) 95% 97% 99% Note 1: RDSON is characterized at 600mA and tested at lower current in production. Note 2: Regulator VSW pin is forced off for 240ns every 8 cycles to ensure the BST cap is replenished. Note 3: For the adjustable version, the ratio of VCC/Vout cannot exceed 16. Note 4: Based on Over Current Detect testing
  • 7 - TS30111 Version 1.0 Specifications subject to change WWW.TRIUNESYSTEMS.COM Copyright © 2012, Triune Systems, LLC FUNCTIONAL DESCRIPTION The TS30111 current-mode synchronous step -down power supply product is ideal for use in the commercial, industrial, and automotive market segments. It includes flexibility to be used for a wide range of output voltages and is optimized for high efficiency power conversion with low RDSON integrated synchronous switches. A 1MHz internal switching frequency facilitates low cost LC filter combinations. Additionally, the fixed output versions enable a minimum external component count to provide a complete regulation solution with only 4 external components: an input bypass capacitor, an inductor, an output capacitor, and the bootstrap capacitor. The regulator automatically transitions between PFM and PWM mode to maximize efficiency for the load demand. The TS30111 was designed to provide these system benefits:  Reduced board real estate  Lower system cost o Lower cost inductor o Low external parts count  Ease of design o Bill of Materials and suggested board layout provided o Power Good output o Integrated compensation network o Wide input voltage range  Robust solution o Over current, over voltage and over temperature protection DETAILED PIN DESCRIPTION Unregulated input, VCC This terminal is the unregulated input voltage source for the IC. It is recommended that a 10uF bypass capacitor be placed close to the device for best performance . Since this is the main supply for the IC, good layout practices need to be followed for this connection. Bootstrap control, BST This terminal will provide the bootstrap voltage required for the upper internal NMOS switch of the buck regulator. An external ceramic capacitor placed between the BST input terminal and the VSW pin will provide the necessary voltage for the upper switch. In normal operation the capacitor is re-charged on every low side synchronous switching action. In the case of where the switch mode approaches 100% duty cycle for the high side FET, the device will automatically reduce the duty cycle switch to a minimum off time on every 8th cycle to allow this capacitor to re-charge. Sense feedback, FB This is the input terminal for the output voltage feedback. For the fixed mode versi ons, this should be hooked directly to V OUT. The connection on the PCB should be kept as short as possible, and should be made as close as possib le to the capacitor. The trace should not be shared with any other connection. (Figure 23) For adjustable mode versions, this should be connected to the external resistor divid er. To choose the resistors, use the following equation: VOUT = 0.8 (1 + RTOP/RBOT) The input to the FB pin is high impedance, and input current should be less than 100nA. As a resu lt, good layout practices are required for the feedback resistors and feedback traces. When using the adjustable version, the feedback trace should be kept as short as possible and minimum width to reduce stray capacitance and to reduce the injection of noise. For the adjustable version, the ratio of VCC/Vout cannot exceed 16.
  • 8 - TS30111 Version 1.0 Specifications subject to change WWW.TRIUNESYSTEMS.COM Copyright © 2012, Triune Systems, LLC Switching output, VSW This is the switching node of the regulator. It should be connected directly to the 3.3uH inductor with a wide, short trace and to one end of the Bootstrap capacitor. It is switching between VCC and PGND at the switching frequency. Ground, GND This ground is used for the majority of the device including the analog reference, control loop, and other circuits. Power Ground, PGND This is a separate ground connection used for the low side sync hronous switch to isolate switching noise from the rest of the device. (Figure 23) Enable, high-voltage, EN This is the input terminal to activate the regulator. The input threshold is TTL/CMOS compatible. It also has an internal pull - up to ensure a stable state if the pin is disconnected. Power Good Output, PG This is an open drain , active low output. The switched mode output voltage is monitored and the PG line will remain low until the output voltage reaches the VOUT-UV threshold. Once the internal comparator detects the output voltage is above the desired threshold, an internal delay timer is activated and the PG line is de-asserted to high once this delay timer expires. In the event the output voltage decreases below VOUT-UV, the PG line will be asserted low and remain low until the output rises above VOUT-UV and the delay timer times out. See Figure 2 for the circuit schematic for the PG signal. INTERNAL PROTECTION DETAILS Internal Current Limit The current through the high side FET is sensed on a cycle by cycle basis and if current l imit is reached, it will abbreviate the cycle. In addition, the device senses the FB pin to identify hard short conditions and will direct the VSW output to skip 4 cycles if current limit occurs when FB is low. This allow s current built up in the inductor during the minimum on time to decay sufficiently. Current limit is always active when the regulator is enabled. Soft start ensures current limit does not prevent regulator startup. Under extended over current conditions (such as a short), the device will automatically disable. Once the over current condition is removed, the device returns to normal operation automatically. (Alternately the factory can configure the device’s NVM to shutdown the regulator if an extended over current event is detected and require a toggle of the Enable pin to return the device to normal operation.) Thermal Shutdown If the temperature of the die exceeds 170 °C (typical), the VSW outputs will tri-state to protect the device from damage. The PG and all other protection circuitry will stay active to inform t he system of the failure mode. Once the device cools to 160 °C (typical), the device will start up again, f ollowing the normal soft start sequence . If the device reaches 170 °C, the shutdown/restart sequence will repeat. Reference Soft Start The reference in this device is ramped at a rate of 4ms to prevent the output from overshoot during startup. This ramp restarts whenever there is a rising edge sensed on the Enable pin. This occurs in both the fixed and adjustable versions. During the soft start ramp, current limit is still active, and will still protect the device in case of a short on the output. Output Overvoltage If the output of the regulator exceeds 103% of the regulation voltage, the VSW outputs will tri-state to protect the device from damage. This check occurs at the start of each switching cycle. If it occurs during the middle of a cycle, the switching for that cycle will complete, and the VSW outputs will tri-state at the beginning of the next cycle. VCC Under-Voltage Lockout The device is held in the off state until VCC reaches 4.3V (typical). There is a 300mV hysteresis on this input, which requires the input to fall below 4V (typical) before the device will disable.
  • 12 - TS30111 Version 1.0 Specifications subject to change WWW.TRIUNESYSTEMS.COM Copyright © 2012, Triune Systems, LLC TYPICAL APPLICATION SCHEMATIC TS30111 VOUT 2.5V PGND VSW VCC FB GND BST VCC PG PG RTOP 17.8K RBOT 10K RPUP 10K (optional) VOUT ENEN CBYPASS 10uF 35V CBST 22nF LOUT 3.3uH COUT1 22uF 10V CBYPASS2 0.1uF (optional) DCATCH (optional) Figure 20: TS30111 Application Schematic A minimal schematic suitable for most applications is shown on page 1. Figure 22 includes optional components that may be considered to address specific issues as listed in the External Component Selection section. PCB LAYOUT For proper operation and minimum EMI, care must be taken during PCB layout. An improper layout can lead to issues such as poor stability and regulation, noise sensitivity and increased EMI radiation. (figure 23) The main guidelines are the following:  provide low inductive and resistive paths for loops with high di/dt,  provide low capacitive paths with respect to all the other nodes for traces with high di/dt,  sensitive nodes not assigned to power transmission should be referenced to the analog signal ground (GND) and be always separated from the power ground (PGND). The negative ends of C BYPASS, COUT and the Schottky diode D CATCH (optional) should be placed close to ea ch other and connected using a wide trace. Vias must be used to connect the PGND node to the ground plane. The PGND node must be placed as close as possible to the TS30111 PGND pins to avoid additional voltage drop in traces. The bypass capacitor CBYPASS (optionally paralleled to a 0.1µF capacitor) must be placed close to the VCC pins of TS30111. The inductor must be placed close to the VSW pins and connected directly to C OUT in order to minimize the area between the VSW pin, the inductor, the C OUT capacitor and the PGND pins. The trace area and length of the switching nodes VSW and BST should be minimized. For the adjustable output voltage version of the TS30111, feedback resistors R BOT and R TOP are required for Vout settings greater than 0. 8V and shoul d be placed close to the TS30111 in order to keep the traces of the sensitive node FB as short as possible and away from switching signals. R BOT should be connected to the analog ground pin (GND) directly and should never be connected to the ground plane. The analog ground trace (GND) should be connected in only one point to the power ground (PGND). A good connection point is under the TS30111 package to the exposed thermal pad and vias which are connected to PGND. RTOP will be connected to the VOUT node using a trace that ends close to the actual load. For fixed output voltage versions of the TS30111, RBOT and RTOP are not required and the FB pin should be connected directly to the Vout.
  • 13 - TS30111 Version 1.0 Specifications subject to change WWW.TRIUNESYSTEMS.COM Copyright © 2012, Triune Systems, LLC The exposed thermal pad must be soldered to the PCB for mechanical r eliability and to achieve good power dissipation. Vias must be placed under the pad to transfer the heat to the ground plane. COUT COUT LOUT CBYPASS DCATCH CBYP RBOT RTOP CBST RPLP PGND VCC VOUT Vias to ground plane Vias to ground plane Analog ground (GND) Switching node VCC VCC GND VSW VCC BST EN VSW PGND PGND VSW VSW NC NC FB PG Figure 21: TS30111 PCB Layout, Top View EXTERNAL COMPONENT BILL OF MATERIALS Designator Function Description Suggested Manufacturer Manufacturer Code Qty CBYPASS Input Supply Bypass Capacitor 10uF 10% 35V TDK CGA5L3X5R1V106K160AB 1 COUT Output Filter Capacitor 22uF 10% 10V TDK C2012X5R1A226K125AB 1 LOUT Output Filter Inductor 3.3uH 900mA TDK Wurth MLP2012S3R3MT 744045003 1 CBST Boost Capacitor 22nF 10V TDK C1005X7R1C223K 1 RTOP Voltage Feedback Resistor (optional) 17.8K (Note 1) 1 RBOT Voltage Feedback Resistor (optional) 10K (Note 1) 1 RPLP PG Pin Pull-up Resistor (optional) 10K 1 DCATCH Catch Diode (optional) 30V 2A SOD-123FL On Semiconductor MBR230LSFT1G 1
  • 14 - TS30111 Version 1.0 Specifications subject to change WWW.TRIUNESYSTEMS.COM Copyright © 2012, Triune Systems, LLC Note 1: The voltage divider resistor values are calculated for an output voltage of 2.5V. For fixed output versions, the FB pin is connected directly to VOUT. EXTERNAL COMPONENT SELECTION The 1MHz internal switching frequency of the TS30111 facilitates low cost LC filter combinations. Additionally, the fixed output versions enable a minimum external component count to provide a complete regulation solution with only 4 external components: an input bypass capacitor, an inductor, an output cap acitor, and the bootstrap capacitor. The internal compensation is optimized for a 22uF output capacitor and a 3.3uH inductor. For best performance, a low ESR ceramic capacitor should be used for C BYPASS. If C BYPASS is not a low ESR ceramic capacitor, a 0.1uF ceramic capacitor should be added in parallel to CBYPASS. The minimum allowable value for the output capacitor is 22 uF. To keep the output ripple low, a low ESR (less than 35mOhm) ceramic is recommended. Multiple capacitors can be paralleled to reduce the ESR. The inductor range is 3.3 uH +/ -20%. For optimal over -current protection, the inductor should be able to handle up to the regulator current limit without saturation. Otherwise, an inductor with a satura tion current rating higher than the maximum IOUT load requirement plus the inductor current ripple should be used. For high current modes, the optional Schottky diode will improve the overall efficiency and reduce the heat. It is up to the user to determine the cost/benefit of adding this additional component in the user’s application. The diode is typically not needed. For the adjustable output version of the TS30111, the output voltage can be adjusted by sizing RTOP and RBOT feedback resistors. The equation for the output voltage is VOUT = 0.8 (1 + RTOP/RBOT). For the adjustable version, the ratio of VCC/Vout cannot exceed 16. RPUP is only required when the Power Good signal (PG) is utilized. THERMAL INFORMATION TS30111 is designed for a maximum operating junction temperature T j of 125°C. The maximum output power is limited by the power losses that can be dissipated over the thermal resistance given by the package and the PCB structures. The PCB must provide heat sinking to keep the TS30111 cool. The exposed metal on the bottom of the QFN package must be soldered to a ground plane. This ground should be tied to other copper layers below with thermal vias. Adding more copper to the top and the bottom layers and tying this copper to the internal planes with vias can reduce thermal resistance further. For a hi -K JEDEC board and 13.5 square inch of 1 oz Cu, the thermal resistance from junction to ambient can be reduced to JA = 38°C/W. The power dissipation of other power components (catch diode, inductor) cause additional copper heating and can further increase what the TS30111 sees as ambient temperature.
  • 15 - TS30111 Version 1.0 Specifications subject to change WWW.TRIUNESYSTEMS.COM Copyright © 2012, Triune Systems, LLC PACKAGE MECHANICAL DRAWINGS (all dimensions in mm)
  • 16 - TS30111 Version 1.0 Specifications subject to change WWW.TRIUNESYSTEMS.COM Copyright © 2012, Triune Systems, LLC RECOMMEDED PCB LAND PATTERN
  • 17 - TS30111 Version 1.0 Specifications subject to change WWW.TRIUNESYSTEMS.COM Copyright © 2012, Triune Systems, LLC PACAKGING INFORMATION Pb-Free (RoHS): The TS30111 devices are fully compliant for all materials covered by European Union Directive 2002/95/EC, and meet all IPC-1752 Level 3 materials declaration requirements. MSL, Peak Temp: The TS30111 family has a Moisture Sensitivity Level (MSL) 1 rating per JEDEC J-STD-020D. These devices also have a Peak Profile Solder Temperature (Tp) of 260°C. IR REFLOW PROFILE
  • 18 - TS30111 Version 1.0 Specifications subject to change WWW.TRIUNESYSTEMS.COM Copyright © 2012, Triune Systems, LLC
  • 19 - TS30111 Version 1.0 Specifications subject to change WWW.TRIUNESYSTEMS.COM Copyright © 2012, Triune Systems, LLC ROHS AND REACH COMPLIANCE Triune Systems is fully committed to environmental quality. All Triune Systems materials and suppliers are fully compliant with RoHS (European Union Directive 2011/65/EU), REACH SVHC Chemical Restrictions (EC 1907/2006), IPC-1752 Level 3 materials declarations, and their subsequent amendments. Triune Systems maintains certified laboratory reports for all product materials, from all suppliers, which show full compliance to restrictions on the following:  Cadmium (Cd)  Chlorofluorocarbons (CFCs)  Chlorinate Hydrocarbons (CHCs)  Halons  Hexavalent Chromium (CrVI)  Hydrobromofluorocarbons (HBFCs)  Hydrochlorofluorocarbons (HCFCs)  Lead (Pb)  Mercury (Hg)  Perfluorocarbons (PFCs)  Polybrominated biphenyls (PBB)  Polybrominated Diphenyl Ethers (PBDEs)
  • 20 - TS30111 Version 1.0 Specifications subject to change WWW.TRIUNESYSTEMS.COM Copyright © 2012, Triune Systems, LLC

ORDERING INFORMATION

Part Number: TS30111-MvvvQFNR-13 (13 inch reel) vvv Output Voltage 015 1.5 V 018 1.8 V 025 2.5 V 033 3.3 V 050 5.0 V

000 Adjustable

  • 21 - TS30111 Version 1.0 Specifications subject to change WWW.TRIUNESYSTEMS.COM Copyright © 2012, Triune Systems, LLC REEL DIMENSIONS (13 INCH)
  • 22 - TS30111 Version 1.0 Specifications subject to change WWW.TRIUNESYSTEMS.COM Copyright © 2012, Triune Systems, LLC CARRIER TAPE SPECIFICATION
  • 23 - TS30111 Version 1.0 Specifications subject to change WWW.TRIUNESYSTEMS.COM Copyright © 2012, Triune Systems, LLC Legal Notices Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. “Typical” parameters whic h may be provided in Triune Systems data sheets and/or specificatio ns can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for your application by your technical experts. TRIUNE SYSTEMS MAKES NO R EPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Triune Systems disclaims all liability a rising from this information and its use. Triune System products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to su pport or sustain life, or for any other application in which the failure of the Triune Systems product could create a situation where personal injury or death m ay occur. Should the Buyer purchase or use Triune Systems products for any such unintended or unauthorized application, the Buyer s hall indemnify and hold Triune Systems, and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expe nses, and reasonable attorney fees arising out of, directly or indirectly, any claim of per sonal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Triune Systems was negligent regarding the design or manufacture of the part. No licenses are conveyed, implici tly or otherwise, under any Triune Systems intellectual property rights. Trademarks All other trademarks mentioned herein are property of their respective companies. © 2013 Triune Systems, LLC. All Rights Reserved.